采用自主设计的高压挤压小试装置,将城市混合生活垃圾分为干、湿两种组分。分析其性质表明:在20 MPa和40 MPa挤压压力下,干组分含水率低于30%,热值从2 778 k J/kg分别提升至14 503,11 659 k J/kg。湿组分性质与混合垃圾中的厨余组分相近...采用自主设计的高压挤压小试装置,将城市混合生活垃圾分为干、湿两种组分。分析其性质表明:在20 MPa和40 MPa挤压压力下,干组分含水率低于30%,热值从2 778 k J/kg分别提升至14 503,11 659 k J/kg。湿组分性质与混合垃圾中的厨余组分相近,易腐成分含量高,可采用厌氧消化处理回收生物质能。采用高压挤压技术作为预处理手段,垃圾能源最大可回收量达5 340 k J/kg,相对直接焚烧提高近90%。高压挤压技术作为预处理手段,可有效提升城市混合生活垃圾的处理效率和能源回收效率。展开更多
To explore the effect of strain rate ε on the high temperature deformation characteristics of ultrafine-grained materials, the deformation and damage features as well as microstructures of ECAP-treated pure Al at dif...To explore the effect of strain rate ε on the high temperature deformation characteristics of ultrafine-grained materials, the deformation and damage features as well as microstructures of ECAP-treated pure Al at different temperatures T and strain ratesε were systematically studied through compression tests and microscopic observations. The increase in ε eliminates strain softening at T≤473 K, and largely enhances the yield strength and flow stress at 473?573 K. The shear deformation dominates the plastic deformation of ECAP-treated Al. Many cracks along shear bands (SBs) are formed at T≥473 K and secondary SBs basically disappear at 1×10?3 s?1; however, at 1×10?2 s?1, cracks are only observed at temperature below 473 K, and secondary SBs become clearer at T≥473 K. The microstructures of ECAP-treated Al mainly consist of sub-grains (SGs). The increase in ε inhibits the SG growth, thus leading to the increases both in yield strength and flow stress at high temperatures.展开更多
The influence of high pressure and manganese addition on Fe-rich phases(FRPs)and mechanical properties of Al-14Si-2Fe alloy with rheo-squeeze casting(RSC)was investigated.The semi-solid alloy melt was treated by ultra...The influence of high pressure and manganese addition on Fe-rich phases(FRPs)and mechanical properties of Al-14Si-2Fe alloy with rheo-squeeze casting(RSC)was investigated.The semi-solid alloy melt was treated by ultrasonic vibration(UV)firstly,and then formed by squeeze casting(SC).Results show that the FRPs in as-cast SC alloys are composed of coarseβ-Al5(Fe,Mn)Si,δ-Al4(Fe,Mn)Si2 and bone-shapedα-Al15(Fe,Mn)3Si2 phases when the pressure is 0 MPa.With RSC process,the FRPs are first refined by UV,and then the solidification under pressure further causes the grains to become smaller.The peritectic transformation occurs during the formation ofαphase.For the alloy with the same composition,the ultimate tensile strength(UTS)of RSC sample is higher than that of the SC sample.With the same forming process,the UTS of Al-14Si-2Fe-0.8Mn alloy is higher than that of Al-14Si-2Fe-0.4Mn alloy.展开更多
Experiments were conducted to evaluate the effects of extrusion ratio on the microstructure and texture developments of AZ31 Mg alloy during forward extrusion. The forward extrusion was undertaken at 400℃ with extrus...Experiments were conducted to evaluate the effects of extrusion ratio on the microstructure and texture developments of AZ31 Mg alloy during forward extrusion. The forward extrusion was undertaken at 400℃ with extrusion ratios of 10, 18, and 25 after the alloy was homogenized at 410℃ for 12 h. Partially recrystallized microstructures were observed in all the extruded rods examined. The texture of the large elongated deformed grains appeared strongly centered at （1010） dominating the extrusion texture, while the recrystallized grains exhibited much more randomized texture. For the alloy with the largest ER （25）, coarse secondary recrystallized grains were found which presented a different texture component with （11 2 0） parallel to the ED. The occurrence of the coarse secondary recrystallized grains in the alloy with the largest ER might be attributed to that the large ER raised the die exit temperature during extrusion and thus promoted significantly grain growth after the extruded rod exited from extrusion die. The intensities of different texture components varied with ER because ER affected the contents of the deformed grains, DRX grains and coarse secondary recrystallized grains. In particular, the maximum intensity of fiber texture was decreased as ER increased due to the decrease of the large elongated deformed grains.展开更多
文摘采用自主设计的高压挤压小试装置,将城市混合生活垃圾分为干、湿两种组分。分析其性质表明:在20 MPa和40 MPa挤压压力下,干组分含水率低于30%,热值从2 778 k J/kg分别提升至14 503,11 659 k J/kg。湿组分性质与混合垃圾中的厨余组分相近,易腐成分含量高,可采用厌氧消化处理回收生物质能。采用高压挤压技术作为预处理手段,垃圾能源最大可回收量达5 340 k J/kg,相对直接焚烧提高近90%。高压挤压技术作为预处理手段,可有效提升城市混合生活垃圾的处理效率和能源回收效率。
基金Projects(51231002,51271054,51571058,50671023)supported by the National Natural Science Foundation of China
文摘To explore the effect of strain rate ε on the high temperature deformation characteristics of ultrafine-grained materials, the deformation and damage features as well as microstructures of ECAP-treated pure Al at different temperatures T and strain ratesε were systematically studied through compression tests and microscopic observations. The increase in ε eliminates strain softening at T≤473 K, and largely enhances the yield strength and flow stress at 473?573 K. The shear deformation dominates the plastic deformation of ECAP-treated Al. Many cracks along shear bands (SBs) are formed at T≥473 K and secondary SBs basically disappear at 1×10?3 s?1; however, at 1×10?2 s?1, cracks are only observed at temperature below 473 K, and secondary SBs become clearer at T≥473 K. The microstructures of ECAP-treated Al mainly consist of sub-grains (SGs). The increase in ε inhibits the SG growth, thus leading to the increases both in yield strength and flow stress at high temperatures.
基金Project(51605342) supported by the National Natural Science Foundation of ChinaProject(2015CFB431) supported by the Natural Science Foundation of Hubei Province,China+1 种基金Project(K201520) supported by the Science Research Foundation of Wuhan Institute of Technology,ChinaProject(2016KA01) supported by the Open Research Fund Program of Hubei Provincial Key Laboratory of Chemical Equipment Intensification and Intrinsic Safety,China
文摘The influence of high pressure and manganese addition on Fe-rich phases(FRPs)and mechanical properties of Al-14Si-2Fe alloy with rheo-squeeze casting(RSC)was investigated.The semi-solid alloy melt was treated by ultrasonic vibration(UV)firstly,and then formed by squeeze casting(SC).Results show that the FRPs in as-cast SC alloys are composed of coarseβ-Al5(Fe,Mn)Si,δ-Al4(Fe,Mn)Si2 and bone-shapedα-Al15(Fe,Mn)3Si2 phases when the pressure is 0 MPa.With RSC process,the FRPs are first refined by UV,and then the solidification under pressure further causes the grains to become smaller.The peritectic transformation occurs during the formation ofαphase.For the alloy with the same composition,the ultimate tensile strength(UTS)of RSC sample is higher than that of the SC sample.With the same forming process,the UTS of Al-14Si-2Fe-0.8Mn alloy is higher than that of Al-14Si-2Fe-0.4Mn alloy.
基金supported by the National Basic Research Program of China ("973" Project) (Grant No. 2007CB613703)the National Natural Science Foundation of China (Grant No. 50890172)the Fundamental Research Funds for the Central Universities (Grant No. CDJXS11132227)
文摘Experiments were conducted to evaluate the effects of extrusion ratio on the microstructure and texture developments of AZ31 Mg alloy during forward extrusion. The forward extrusion was undertaken at 400℃ with extrusion ratios of 10, 18, and 25 after the alloy was homogenized at 410℃ for 12 h. Partially recrystallized microstructures were observed in all the extruded rods examined. The texture of the large elongated deformed grains appeared strongly centered at （1010） dominating the extrusion texture, while the recrystallized grains exhibited much more randomized texture. For the alloy with the largest ER （25）, coarse secondary recrystallized grains were found which presented a different texture component with （11 2 0） parallel to the ED. The occurrence of the coarse secondary recrystallized grains in the alloy with the largest ER might be attributed to that the large ER raised the die exit temperature during extrusion and thus promoted significantly grain growth after the extruded rod exited from extrusion die. The intensities of different texture components varied with ER because ER affected the contents of the deformed grains, DRX grains and coarse secondary recrystallized grains. In particular, the maximum intensity of fiber texture was decreased as ER increased due to the decrease of the large elongated deformed grains.
