ICP-AES Determination of Germanium in GdSiGe Series Alloys as Magnetic Refrigeration Material

The ICP-AES method for the determination of Ge in GdSiGe series alloys was studied.As the three main elements in the alloys,Gd,Si,and Ge differ greatly from each other in chemical properties,it was difficult to pretreat the sample.Two decomposition methods were compared,and a mixture of HNO3＋HF was used to decompose the sample and the effect of the HF amount on the sample decomposition was examined.The adsorption effect of GdF3 on Ge was discussed.Three GdSiGe series alloy samples were analyzed,and the RSDs of this method were in the range of 0.85%～2.66%.

Influence of Al content on machinability of AZ series Mg alloys

Influence of A1 content on the machinability of AZ series cast Mg alloys was investigated. In order to evaluate the machinability of the alloys, measurements of the cutting forces during turning operations and surface roughness were carried out as well as considering the microstructure and tensile properties. The results show that maximum tensile properties are observed with 2% （mass fraction） A1 addition to Mg. As the A1 content of the alloy increases above 2%, the cutting forces tend to reduce along with the ductility owing to the grain boundary precipitation of intermetallic phase （fl-Mgl7All2）. Cutting forces are able to increase as the cutting speed increases for all the alloys studied, and it＇s attributed to flank built up at the tip of the cutting tool during machining.

Combustion synthesis of fine TiFe series alloy powder by magnesothermic reduction of ilmenite

Fine TiFe series alloy powder was fabricated by magnesothermic reduction of ilmenite as main raw material.Adiabatic temperature of the FeTiO_(3)-Mg system was studied through thermodynamic analysis.Meanwhile,the characteristics of TiFe series alloy were described by XRD,SEM and grading analysis.It is shown that combustion synthesis of the FeTiO_(3)-Mg system can carry out due to its strong exothermic reaction through adiabatic temperature calculate.Ultrafine TiFe series alloy powder after leached for 5 h has reasonable phases and morphology with the particle distribution of 0.2 to 1μm.It indicates that in-situ magnesothermic reduction of natural ilmenite is a feasible way to fabricate ultrafine powder with a relatively lower cost.

Strengthening-toughening of 7xxx series high strength aluminum alloys by heat treatment

The effects of stepped solution heat treatments on the dissolution of soluble remnant constituents and mechanical properties of 7055 aluminum alloy were investigated. It was shown that a suitable pretreatment at lower temperature can enable complete dissolution of the constituent particles in 7055 alloy without overheating by subsequent high temperature solution treatment. This in turn increased the tensile strength and fracture toughness of 7055 alloy to 805 MPa and 41.5 MPa·m 1/2 respectively, with approximately 9% tensile elongation. The near solvus pre precipitation following after high temperature solution treatment was also studied on 7055 aluminum alloy. The effect of the pre precipitation on the microstructure, age hardening and stress corrosion cracking of 7055 alloy was investigated. The optical and transimission electron microscopy observation show that the near solvus pre precipitation can be limited to grain boundary and enhance the discontinuity of grain boundary precipitates in the subsequent ageing. The stress corrosion cracking resistance of aged 7055 alloy can be improved via the pre precipitation with non deteriorated strength and plasticity.

Influence of aluminum content on machinability of AS series cast magnesium alloys

The influence of Al content on machinability of AS series cast Mg alloys was studied. The assessment of machinability of Mg alloys was performed by measuring the cutting forces and surface roughness. The microstructure and the tensile properties were also studied. The results reveal that cutting forces are increased with the increase of the Al content. Surface roughness and mechanical properties are the highest for AS91 Mg alloy. It is assumed that the main mechanism, which has an influence on the mechanical properties, is the presence of intermetallic phases(Mg2Si and Mg17Al12). Cutting forces increase with the increase of the cutting speed in machining of all Mg alloys. These measured data are in accordance with the mechanical properties of the machined alloys.

Experiments and modeling of double-peak precipitation hardening and strengthening mechanisms in Al-Zn-Mg alloy

The aim of the present work is to develop a model for simulating double-peak precipitation hardening kinetics in Al-Zn-Mg alloy with the simultaneous formation of different types of precipitates at elevated temperatures based on the modified Langer-Schwartz approach. The double aging peaks are present in the long time age-hardening curves of Al-Zn-Mg alloys. The physically-based model, while taking explicitly into account nucleation, growth, coarsening of the new phase precipitations and two strengthening mechanisms associated with particle-dislocation interaction （shearing and bypassing）, was used for the analysis of precipitates evolution and precipitation hardening during aging of Al-Zn-Mg alloy. Model predictions were compared with the measurements of Al-Zn-Mg alloy. The systematic and quantitative results show that the predicted hardness profiles of double peaks via adding a shape dependent parameter in the growth equation for growth and coarsening generally agree well with the measured ones. Two strengthening mechanisms associated with particle-dislocation interaction （shearing and bypassing） were considered operating simultaneously in view of the particle size-distribution. The transition from shearing to bypassing strengthening mechanism was found to occur at rather early stage of the particle growth. The bypassing was found to be the prevailing strengthening mechanism in the investigated alloys.

Effect of flame rectification on corrosion property of Al-Zn-Mg alloy

The corrosion resistance of Al？Zn？Mg alloy subjected to different times in flame rectification was investigated based on the exfoliation corrosion test. The results indicate that the flame rectification deteriorates the exfoliation corrosion resistance of Al？Zn？Mg alloy. The corrosion resistance of Al-Zn-Mg alloy is ranked in the following order： base metal〉two times〉three times〉one time of flame rectification. The exfoliation corrosion behavior was discussed based on the transformation of precipitates at grain boundaries and matrix. With increasing the number of times in flame rectification, the precipitate-free zones disappeared and the precipitates experienced dissolution and re-precipitation. The sample was seriously corroded after one time of flame rectification, because the precipitates at grain boundaries are more continuous than those in other samples.

Determination of kinetic parameters from calorimetric study of solid state reactions in 7150 Al-Zn-Mg alloy

Differential scanning calorimetric （DSC） study was carried out at different heating rates to examine the solid state reactions in a 7150 A1-Zn-Mg alloy in water-quenched （WQ） state, naturally and artificially aged tempers. The exothermic and endothermic peaks of the thermograms indicating the solid state reaction sequence were identified. The shift of peak temperatures to higher temperatures with increasing heating rates suggests that the solid state reactions are thermally activated and kinetically controlled. The artificial aging behaviour of the alloy was assessed by measuring the variations of hardness with aging time. The fraction of transformation （Y）, the rate of transformation （dY/dt）, the transformation functionflY）, and the kinetic parameters such as activation energy （Q） and frequency factor （k0） of all the solid state reactions in the alloy were determined by analyzing the DSC data, i.e. heat flow involved with the corresponding DSC peaks. It was found that the kinetic parameters of the solid state reactions are in good agreement with the published data.

Microstructure and impact mechanical properties of multi-layer and multi-pass TIG welded joints of Al-Zn-Mg alloy plates

The microstructure and mechanical properties of multi-layer multi-pass TIG welded joints of Al-Zn-Mg alloy plates were studied.The phase constituent and microstructure of different regions of the welded joints were characterized by scanning electron microscopy(SEM),X-ray diffraction(XRD),transmission electron microscopy(TEM)and energy disperse spectrum(EDS),while the mechanical properties were evaluated according to the impact test.A dispersively distributed spherical and needle-likeη(MgZn2)phase was obtained in the welding seam.The phase composition of the heat-affected zone(HAZ)wasα(Al)+η(MgZn2)+Al6Mn,and there were a large number of dispersively precipitated nanoscale particles.The welded joint zone had the highest impact toughness as compared with the other parts of the joint.The MgZn2 phase in the weld zone contributed to the improved toughness of the joint.Al2 MgCu phase in HAZ was proven to act as a crack source during fracture.

Ageing Effect on Hardness and Microstructure of Al-Zn-Mg Alloys

Experimental results of the investigation on the hardness of two Al-Zn-Mg alloys [Al-10.0 Zn-4.0 Mg and Al-8.5 Zn-3.0 Mg (wt pct)] aged in the temperature range 60～310℃ for different intervals of time from 1/4 h to 168 h are presented. Both the alloys were found to show identical behaviour of hardness with ageing time. Alloy with higher Zn and Mg content had higher hardness than the alloy with lower solute content. There were three ranges of temperature in which different types of precipitates formed and affected the hardness. Some of the grain boundaries were found to migrate and precipitate free zone has been observed.

Relationship between elements migration ofα-AlFeMnSi phase and micro-galvanic corrosion sensitivity of Al-Zn-Mg alloy

First principles calculations and scanning Kelvin probe force microscopy(SKPFM)were used to investigate the effect of elements migration ofα-AlFeMnSi phase on micro-galvanic corrosion behavior of Al-Zn-Mg alloy.The simulation results showed that the average work function difference between theα-AlFeMnSi phase and Al matrix decreased from 0.232 to 0.065 eV due to the synchronous migration of elements Fe-Mn-Si.Specifically,as the elements Fe-Si migration during the extrusion process,the average Volta potential difference detected by SKPFM between theα-AlFeMnSi phase and Al matrix dropped down to 432.383 mV from 648.370 mV.Thus,the elements migration reduced the micro-galvanic corrosion sensitivity of Al-Zn-Mg alloy.To reach the calculated low micro-galvanic tendency betweenα-AlFeMnSi phase and Al matrix,the diffusion of Mn should be promoted during extruding process.

Solidification path calculations of Al-Zn-Mg alloys in Al-rich corner

The solidification paths of Al-Zn-Mg alloys in the Al-rich corner were investigated. The thermodynamic data for the calculation are obtained by direct coupling with the CALPHAD software Thermo-Calc via its TQ6-interface and the COST2 database. The influences of the initial compositions and the extent of solid back diffusion on the solidification path were numerically investigated by sample calculation of the ternary Al-Zn-Mg alloys. The calculation results of solidification paths of the selected alloys: Al-Zn-3 Mg(in wt.%), Al-5 Zn-10 Mg, Al-2.5Zn-15Mg, Al-10Zn-20.5 Mg, Al-8Zn-25 Mg, were: L→(L+α-Al), L→(L+α-Al)→(L+α-Al+TAU), L→(L+α-Al)→(L+α-Al+Al Mg_β), L→(L+α-Al)→(L+α-Al+TAU)→(L+α-Al+TAU+Al Mg_β), L→(L+α-Al)→(L+α-Al+Al Mg_β)→(L+α-Al+TAU+Al Mg_β), respectively. The results show that the initial compositions and the extent of solid back diffusion have a great influence on solidification path, and the amounts of eutectic phase increase with the decrease of the solid back diffusion coefficient. The equilibrium solute partition coefficients for Zn and Mg in alloys are also calculated and their influence on micro-segregation in the primary solidification of Al-5Zn-10 Mg alloy is analyzed.

Fracture Toughness of Cast Al-Zn-Mg Alloys

Compact tension specimens of as-cast Al-3Zn-2Mg and Al-7Zn-2Mg (in wt pct) alloys were subjected to fracture toughness tests at room temperature according to specification5 laid down in ASTM E-399-81. It was found that increasing the Zn content, grain refinement and increasing the solidification rate lead to an increase in the fracture toughness of the material.

SUPERPLASTICITY OF Al-Zn-Mg-Zr-RE AND Al-Zn-Mg-Ti ALLOYS AND THEIR CAVITATION BEHAVIOUR DURING DEFORMATION

The superplasticity of the Al-Zn-Mg-Zr-RE(alloy A)and Al-Zn-Mg-Ti(alloy B),their change of volume fraction of metastable micro-cavities under various reduction of area and strain rates,as well as the growth of stable cavities in them have been studied by means of small angle X-ray scattering analyses and quantitative metalloraphy respectively.Experimen- tal results show that the volume fraction of metastable micro-cavities of the alloy A is more than that of the alloy B,but the growth rate of stable cavities in alloy A is less than that in al- loy B.Thus,it is believed that the superplasticity of alloy A is superior to that of alloy B.

铸轧Al-Zn-Mg-Cu-Sc-Zr合金短流程制备及组织性能研究

通过Sc元素微合金化和电磁场获得了无中心偏析、带状晶间偏析细小和组织均匀分布的铸轧Al-Zn-Mg-Cu-Sc-Zr(以下称“7xxx系”)铝合金板材,并设计了适用于铸轧组织特征的新型短流程轧制-热处理工艺路线(以下简称“短流程工艺路线”)。短流程工艺路线在轧制破碎粗大结晶相和缩小元素扩散距离的作用下,结晶相显著细化,并在中间短时均匀化和固溶处理过程中快速溶解。与传统工艺路线下的T6态样品相比,尽管短流程工艺路线省略了长时间均匀化工艺,但其结晶相溶解更加充分,残余结晶相和晶粒组织显著细化。在传统工艺路线下,C-T6板材的屈服强度、抗拉强度和延伸率分别为568 MPa、618 MPa和8.7%。在短流程工艺路线下,S-T6样品依然保持了良好的力学性能,相应性能分别为551 MPa、605 MPa和10.4%。

Characterization of dynamic microstructural evolution of AA7150 aluminum alloy at high strain rate during hot deformation

The AA7150 aluminum alloy was compressed to various strains at strain rate of 10 s（-1） and temperatures of 300 °C and 450 °C, respectively. Flow stress behavior, substructure evolution, morphology and spatial distribution of precipitates were studied based on differential scanning calorimetry analysis and transmission electron microscope observation. The results showed that dynamic flow softening occurs during hot deformation. The main softening mechanism could be concluded as dynamic recovery at 300 °C and continuous dynamic recrystallization at 450 °C. The clear heterogeneous spatial distributions of precipitates are found during deformation and enhanced with increased strain. Higher contents of Cu in T phases are found at 450 °C than at 300 °C, which present a transformation process from T phases to S phases as well. The associated evidence of dynamic precipitation on dislocations and particle-stimulated nucleation, as well as the detailed microstructural inherited relationship and morphological texture（particles preferred orientation） were characterized.

Al-Zn-Mg系合金研究现状

Al-Zn-Mg系合金具有高的强度、韧性,良好的焊接性能和工艺性能,是建筑、军用设施、航空航天器与地面车辆和装备的主要焊接结构材料。在查阅大量文献的基础上,指出了Al-Zn-Mg系合金中各元素对合金组织和性能的影响;介绍了国内外Al-Zn-Mg系合金的研究现状、存在的问题及发展趋势。

Precipitation kinetics of GP zones,metastable η′ phase and equilibrium η phase in Al-5.46wt.%Zn-1.67wt.%Mg alloy

Thermal analysis is one of the most used techniques for analyzing the behavior of aluminum alloys in order to analyze the precipitation of Guinier-Preston(GP)zones and different phases formed.In the present work,the behavior of the Al-5.46wt.%Zn-1.67wt.%Mg alloy was studied.The mechanism and kinetics of precipitation of the GP,the metastable phaseη′and the equilibrium phaseηwere investigated using DSC carried out between room temperature and 480℃at heating rates of 5,10,15 and 20℃/min.The apparent activation energies,calculated by DSC from isothermal calculation method using JMAK model,for GP,η′andηwere 56,79 and 96 kJ/mol,respectively,and those calculated by non-isothermal calculation method using Kissinger methods were 57,82 and 99 kJ/mol,respectively.The values of Avrami parameter,n,from isothermal calculation,during the precipitation of the GP,η′andηwere 1.103,1.9075 and 1.92,respectively,and those calculated by non-isothermal were 0.86,2.30 and 2.24,respectively.The results show that GP zones formation is governed by the migration of Zn and Mg atoms while the precipitation of theη′metastable phase and theηstable phase is governed by both the migration and the diffusion of the solute atoms.

A comparative study on corrosion of Mg-Al-Si alloys

Corrosion behavior of various Mg-Al-Si alloys(AS11,AS21,AS41,AS61and AS91series),cast under the same coolingconditions and controlled alloying composition,was investigated systematically.Optical microscopy and scanning electronmicroscopy were used for microstructural examinations.The corrosion behavior was evaluated by immersion tests andpotentiodynamic polarization measurements in3.5%NaCl solution.The results from both immersion tests and the potentiodynamicpolarization measurements showed that marginal improvement in corrosion resistance was observed with2.0%Al(mass fraction)containing alloy(AS21)whereas Al addition above2.0%(AS41,AS61and AS91)deteriorated the corrosion resistance which wasattributed toβphase,acting as cathode,and the interruption of continuity of the oxide film on the surface of the alloys owing tocoarsenedβand Mg2Si phases.

Effect of ageing process on microstructure, corrosion behaviors and mechanical properties of Al-5.6Zn-1.6Mg-0.05Zr alloy

The influence of different ageing processes on the microstructure, corrosion behaviors and mechanical properties of extruded Al-5.6Zn-1.6Mg-0.05Zr(wt.%) alloy was studied in this work. The changes of morphology, size and distribution of MgZn_(2)precipitate with ageing temperature and time were revealed by optical and electron microscopy. Intergranular corrosion(IGC) and exfoliation corrosion(EXCO) tests were carried out to assess the changes in corrosion susceptibility of the tempered alloy, and some white spots on the surface of the sample aged for longer time were found to be precursors of pits. Electrochemical cyclic polarization test depicted the corrosion behavior under different tempers. Ageing influences on the mechanical behaviors of the alloy were revealed by evaluating its microhardness and tensile strength. The microscopic features of the strengthening phases determined by the ageing procedure directly affect the corrosion resistance and mechanical properties of the alloy.