Experimental investigation of vibration pretreatment-microwave curing process for carbon fiber reinforced resin matrix composites

The vibration pretreatment-microwave curing process is an efficient,low energy consumption,and high-quality out-of-autoclave curing process for carbon fiber resin matrix composites.This study aims to investigate the impact of vibration pretreatment temperature on the fiber weight content,microscopic morphology and mechanical properties of the composite laminates by using optical digital microscopy,universal tensile testing machine and thermo-gravimetric analyzer.Additionally,the combined mode of Bragg fiber grating sensor and temperature measurement fiber was employed to explore the effect of vibration pretreatment on the strain process during microwave curing.The study results revealed that the change in vibration pretreatment temperature had a slight impact on the fiber weight content when the vibration acceleration remained constant.The metallographic and interlaminar strength of the specimen formed at a vibration pretreatment temperature of 80℃ demonstrated a porosity of 0.414% and a 10.69% decrease in interlaminar shear strength compared to autoclave curing.Moreover,the introduction of the vibration energy field during the microwave curing process led to a significant reduction in residual strain in both the 0°and 90°fiber directions,when the laminate was cooled to 60℃.

Fabrication and Properties of a New Reactive Diluent for Cationic UV Curing

The reactive diluent prepared by siloxane modified Trimethylene oxide can improve the performance of the UV curing system.Therefore,1,7-bis[(3-ethyl-3-methoxyoxacylobutane)propyl]octadecylosiloxane(BEMOPOMTS)was synthesized from diethyl carbonate,trimethylopropanes,allyl bromide,and 1,1,3,3,5,5,7,7-octadecylosiloxane as the main raw materials.BEMOPOMTS can be used as reactive diluents in the field of cationic UV curing.It has good thermal stability,and the addition of BEMOPOMTS significantly improves the tensile strength and elongation at break of epoxy resin.Compared with the pure epoxy resin,adding 20%BEMOPOMTS increased the elastic modulus by 25%to 677 MPa.

A strength model for cement-stabilized mud subjected to various curing temperatures and its early-stage quality control

The influence of curing temperature on the strength development of cement-stabilized mud has been well documented in terms of strength-increase rate and ultimate strength.However,the strength development model is not mature for the extremely early stages.In addition,there is a lack of studies on quality control methods based on early-stage strength development.This paper presents a strength model for cement-stabilized mud to address these gaps,considering various curing temperatures and early-stage behaviors.In this study,a series of laboratory experiments was conducted on two types of muds treated with Portland blast furnace cement and ordinary Portland cement under four different temperatures.The results indicate that elevated temperatures expedite strength development and lead to higher long-term strength.The proposed model,which combines a three-step conversion process and a hyperbolic model at the reference temperature,enables accurate estimate of the strength development for cement-treated mud with any proportions cured under various temperatures.With this model,a practical early quality control method is introduced for applying cement-stabilized mud in field projects.The back-analysis parameters obtained from a 36-h investigation at temperature of 60C demonstrated a sufficient accuracy in predicting strength levels in practical applications.

Fluorinated semi-interpenetrating polymer networks for enhancing the mechanical performance and storage stability of polymer-bonded explosives by controlling curing and phase separation rates

Herein, the effect of fluoropolymer binders on the properties of polymer-bonded explosives(PBXs) was comprehensively investigated. To this end, fluorinated semi-interpenetrating polymer networks(semiIPNs) were prepared using different catalyst amounts(denoted as F23-CLF-30-D). The involved curing and phase separation processes were monitored using Fourier-transform infrared spectroscopy, differential scanning calorimetry, a haze meter and a rheometer. Curing rate constant and activation energy were calculated using a theoretical model and numerical method, respectively. Results revealed that owing to its co-continuous micro-phase separation structure, the F23-CLF-30-D3 semi-IPN exhibited considerably higher tensile strength and elongation at break than pure fluororubber F2314 and the F23-CLF-30-D0 semi-IPN because the phase separation and curing rates matched in the initial stage of curing.An arc Brazilian test revealed that F23-CLF-30-D-based composites used as mock materials for PBXs exhibited excellent mechanical performance and storage stability. Thus, the matched curing and phase separation rates play a crucial role during the fabrication of high-performance semi-IPNs;these factors can be feasibly controlled using an appropriate catalyst amount.

Alkali Tolerance of Concrete Internal Curing Agent Based on Sodium Carboxymethyl Starch

Internal curing agents (ICA) based on super absorbent polymer have poor alkali tolerance and reduce the early strength of concrete.An alkali tolerate internal curing agent (CAA-ICA) was designed and prepared by using sodium carboxymethyl starch (CMS) with high hydrophilicity,acrylic acid (AA) containing anionic carboxylic group and acrylamide (AM) containing non-ionic amide group as the main raw materials.The results show that the ratio of CAA-ICA alkali absorption solution is higher than that existing ICA,which solves the low water absorption ratio of the ICA in alkali environment.The water absorption ratio of CAA-ICA in saturated Ca(OH)_(2) solution is 95.8 g·g^(-1),and the alkali tolerance coefficient is 3.4.The application of CAA-ICA in cement-based materials can increase the internal relative humidity and miniaturize the pore structure.The compressive strength of mortar increases up to 12.95%at 28 d,which provids a solution to overcome the reduction of the early strength.

Study on Effects of Curing Process on Characteristics of Marinated Beef Products

[Objectives]This study was conducted to compare the effects of different curing processes on the characteristics of marinated beef.[Methods]Marinated beef was obtained by two curing processes:static curing and injection and vacuum tumbling curing.The effects of the two curing processes on the production rate,curing absorption rate,water content,soluble protein content,amino acid nitrogen content,texture characteristics and microstructure of the product were compared.[Results]Compared with static curing,the production rate of marinated beef increased by 10%,the curing absorption rate increased by 28%,the texture and microstructure were improved,and the water content increased,while the soluble protein content decreased.As a result,the sensory score was higher.There was no significant difference in the content of amino acid nitrogen,but it decreased compared with raw meat.To sum up,injection and vacuum tumbling curing is more conducive to the processing of marinated beef.[Conclusions]This study provides a theoretical basis for the industrial production of marinated beef,and lays a foundation for in-depth exploration of injection and vacuum tumbling curing technique of marinated beef.

Synthesis of Ionic and Non-Ionic Modified Waterborne Polyurethane Curing Agent

By using HDI and TMP as the main raw materials,polyethylene glycol 400(PEG400)is used as a non-ionic hydrophilic modifier,and sodium hydroxyethyl sulfonate is used as an ionic hydrophilic modifier to synthesize a dual hydrophilic modified polyurethane curing agent.Research revealed that introducing PEG400 for hydrophilic chain segments and sodium hydroxyethyl sulfonate for hydrophilic ionic groups in the polyurethane curing agent component leads to a uniform distribution of hydrophilic components,significantly enhancing compatibility with the aqueous polyol component,and results in excellent film performance.The synthesis process and film were characterized using Fourier transform infrared spectroscopy and high-resolution scanning electron microscopy in the study.

Advancements and Applications of Polyurethane Curing Technology in Railway Track Bed Construction in China

This paper examines the application of polyurethane curing technology in the construction of railway track beds,with a specific focus on its implementation in China’s rapidly developing railway infrastructure.The study begins by identifying the limitations of traditional ballasted track beds,especially under the demands of high-speed and heavyload railways.It then methodically analyzes the advantages of polyurethane-cured track beds,highlighting their improved mechanical properties,including enhanced stability and durability.The paper further explores the benefits of transitioning to prefabricated polyurethane track beds,emphasizing significant cost reductions,better construction quality,and enhanced maintainability.Through a detailed review of experimental data and practical applications,the paper demonstrates the efficacy of polyurethane track beds in various railway settings.A critical part of the research involves optimizing the structural parameters of polyurethane track beds to achieve the best balance of mechanical and damping properties.The conclusion of the paper underscores the potential of polyurethane curing technology as a transformative approach to railway track bed construction,offering a solution to the challenges posed by traditional methods and aligning with the evolving needs of modern railways.

Securing the Sea Lanes

Some people,mainly in the West,were taken by surprise when six Chinese warships were seen near the Red Sea in October 2023 amid the conflict in Gaza.Some Western media and politicians tried to frame China’s mission as an escalatory move in the Middle East.

Securing Sustenance

National food security is the backbone of any economy,and achieving food security is essential for the prosperity of a nation.During my study in China at the Institute of South-South Cooperation and Development,Peking University,from September 2022 to July 2023,I leant how China has managed to achieve food security despite its large population of around 1.4 billion and numerous other challenges by means of strategic planning,e"ective policy execution,technological advancement and global collaboration.

Multiphysics processes in the interfacial transition zone of fiber-reinforced cementitious composites under induced curing pressure and implications for mine backfill materials: A critical review

The mesoscale fiber-matrix interfacial transition zone(FM-ITZ) under induced curing pressure plays a key role in the effectiveness of fiber reinforcement and the engineering application of fiber-reinforced cementitious composites(FRCCs). This critical review establishes the link among induced curing pressure(i.e., external loading condition), multiphysics processes(i.e., internal governing mechanism), and interface behavior(i.e., material behavior) for FRCC materials through analysis of the state-of-the-art research findings on the FM-ITZ of FRCC materials. The following results are obtained. For the mechanical process, the induced curing pressure changes the stress state and enhances multicracking behavior, which can strengthen the FM-ITZ. For the hydraulic process, the strengthened seepage of the FM-ITZ under induced curing pressure weakens the effective stress and exaggerates the deficiency in water retention capacity between the bulk matrix and the FMITZ. For the thermal process, the induced curing pressure causes a steep temperature gradient in the FM-ITZ and thus influences the temperature evolution and thermally-induced microcracks in the FM-ITZ. For the chemical process, the induced curing pressure enhances hydration kinetics and results in the formation of additional hydration products in the FM-ITZ. Moreover, recommendations are proposed on the basis of findings from this review to facilitate the implementation of fiber reinforcement in cemented paste backfill technology.

Internal Curing Mechanism of Sepiolite in Cement Paste

In order to explore the internal curing mechanism of sepiolite in cement-based materials,the effects of sepiolite on the water consumption of standard consistency,setting time,viscosity,strength,pore structure characteristics,micro-hardness characteristics and two-dimensional surface characteristics of cement paste were studied,respectively.The experimental results show that the water consumption of standard consistency increases linearly with the increase of sepiolite content.The setting time and viscosity are also lengthened and increased with the addition of sepiolite,respectively.When the content of sepiolite exceeds 5%,the strength of the specimen increases significantly.The BET results show that the pore structure of the interfacial transition zone(ITZ)in hardened cement paste(HCP)with sepiolite is optimized after curing for28 d and its pore volume content with below 10 nm is decreased,especially for the specimen with a lower watercement ratio.The characteristics of microhardness and strength of specimens have the same law.Backscattered electron image(BSE-IA)shows that the ITZ of the specimen with sepiolite is denser and the unhydrated cement particles are less than the reference specimen.

Effect of High Temperature Curing on the Frost Resistance of Recycled Aggregate Concrete and the Physical Properties of Second-Generation Recycled Coarse Aggregate under Freeze-Thaw Cycles

With the emphasis on environmental issues,the recycling of waste concrete,even recycled concrete,has become a hot spot in the field of architecture.But the repeated recycling of waste concrete used in harsh environments is still a complex problem.This paper discusses the durability and recyclability of recycled aggregate concrete(RAC)as a prefabricated material in the harsh environment,the effect of high-temperature curing(60℃,80℃,and 100℃)on the frost resistance of RAC and physical properties of the second generation recycled coarse aggregate(RCA_(2))of RAC after 300 freeze-thaw cycles were studied.The frost resistance of RAC was characterized by compressive strength,relative dynamic elastic modulus,and mass loss.As the physical properties of RCA_(2),the apparent density,water absorption,and crushing value were measured.And the SEM images of RAC after 300 freeze-thaw cycles were shown.The results indicated that the frost resistance of RAC cured at 80℃ for 7 days was comparable to that cured in the standard condition(cured for 28 days at 20℃±2℃ and 95%humidity),and the RAC cured at 100℃ was slightly worse.However,the frost resistance of RAC cured at 60℃ deteriorated seriously.The RAC cured at 80℃ for 7 days is the best.Whether after the freeze-thaw cycle or not,the RCA that curd at 60℃,80℃,and 100℃ for 7 days can also meet the requirements of Grade III RCA and be used as the aggregate of non-bearing part of prefabricated concrete components.RCA_(2) which is cured at 80℃ for 7 days had the best physical properties.

Influence Mechanism of Curing Regimes on Interfacial Transition Zone of Lightweight Ultra-High Performance Concrete

This study aims to clarify the effects of curing regimes and lightweight aggregate(LWA)on the morphology, width and mechanical properties of the interfacial transition zone(ITZ) of ultra-high performance concrete(UHPC), and provide reference for the selection of lightweight ultra-high performance concrete(L-UHPC) curing regimes and the pre-wetting degree LWA. The results show that, under the three curing regimes(standard curing, steam curing and autoclaved curing), LWA is tightly bound to the matrix without obvious boundaries. ITZ width increases with the water absorption of LWA and decreases with increasing curing temperature. The ITZ microhardness is the highest when water absorption is 3%, and the microhardness value is more stable with the distance from LWA. Steam and autoclaved curing increase ITZ microhardness compared to standard curing. As LWA pre-wetting and curing temperatures increase, the degree of hydration at the ITZ increases, generating high-density CSH(HD CSH) and ultra-high-density CSH(UHD CSH), and reducing unhydrated particles in ITZ. ITZ micro-mechanical properties are optimized due to hydration products being denser.

Synergistic Use of CO_(2) Pretreatment and Accelerated Carbonation Curing for Maximum Recycling of Steel Slag

Two carbonation approaches are considered for studying the effects on the hardening mechanisms of slurries made of 100 wt%electric arc furnace steel slag (EAF) slag or 80 wt%EAF slag incorporating 20 wt% of Portland cement,which are applied during the hot-stage pretreatment with simulated gas for raw steel slag or the accelerated carbonation curing of slurry.The mechanical strengths,carbonate products,microstructures and CO_(2) uptakes were quantitatively investigated.Results manifest that accelerated carbonation curing increases the compressive strengths of steel slag slurry,from 17.1 MPa (binder of 80 wt% EAF and 20 wt%cement under standard moisture curing) to 36.0 MPa (binder of 80 wt%EAF and 20 wt%cement under accelerated carbonation curing),with a CO_(2) uptake of 52%.In contrast,hot-stage carbonation applied during the pretreatment of steel slag increases the compressive strengths to 43.7 MPa (binder of 80 wt%carbonated EAF and 20 wt%cement under accelerated carbonation curing),with a CO_(2) uptake of 67%.Hotstage carbonation of steel slag is found for particle agglomeration,minerals remodeling and calcite formed,thus causing an activated steel slag with a dense structure and more active components.Accelerated carbonation curing of steel slag slurry paste results in the newly formed amorphous CaCO_(3),calcite crystalline and silica gels that covered the pores of the matrix,facilitating microstructure densification and strength improvement.Adopting the combinative methods of the hot-stage CO_(2) pretreatment and accelerated carbonation curing creates a promising high-volume steel slag-based binder with high strengths and CO_(2) storage.

Numerical Study on the Resin Transfer Molding Curing Process for Thick Composites Materials

The successful manufacture of thick composites is challenging since the highly exothermic nature of thermoset resins and limited temperature control make avoiding the onset of detrimental thermal gradients within the composite relatively difficult.This phenomenon is mainly caused by exothermic heat reactions.The so-called Michaud's model has been largely used in the literature to reduce the gap between experience and simulation with regard to the effective prediction of the temperature cycle in these processes.In this work,another solution is proposed to simulate the curing process for thick composites,namely preheating the resin to activate the curing reaction before resin injection into the mold.A good agreement between the experiment and the simulation is found.Moreover,in order to minimize the thermal gradient in the final composite,the thermophysical properties of the fiber and the torque(temperature,time)of the Plate have been varied leading to interesting results.

Effects of Curing Methods on the Permeability and Mechanism of Cover Concrete

Curing methods are one of the most important factors in determining the quality and compactness of cover concrete.The effect of curing methods on the water absorption and sorptivity coefficient of cover concrete with the substitution ratio of fly ash(FA)and ground granulated blast slag(GGBS)for cement between 30 wt%and 40 wt%was studied by capillary water absorption test.The vacuum saturation test and mercury intrusion test were employed to characterize these differences in the pore structure of cover concrete under different curing methods.With further analysis of the compactness of microstructure by SEM,the mechanism of the impact of curing methods on the permeability of cover concrete was revealed.The results obtained indicate that the effect of curing methods on the water absorption,sorptivity coefficient and porosity of cover concrete shows the trend of natural curing>cover curing>water curing>standard curing.It is also shown that reasonable curing is advantageous to reduce the porosity and permeability of cover concrete.In natural curing conditions,the appearance of porosity increasing and pore structure coarsening is more critical for covering concrete with mineral admixtures than for pure cement concrete.Therefore,the permeability of cover concrete with mineral admixtures is more sensitive to the early-age curing methods.

Application of Polyurethane Curing Barn in Flue-cured Tobacco Production

[ Objective] This study aimed to investigate the curing performance of polyurethane curing barn and reduce the cost of tobacco leaf flue-curing. [ Meth- odl The temperature control effect, curing effect and curing cost of polyurethane curing barn and traditional bulk curing barn were analyzed and compared. [ Re- suit] The results showed that there were no significant differences in curing performance between two types of curing barns. Horizontal temperature differences in- creased slightly as the temperature rose. Specifically, horizontal temperature differences between each layer ranged from 0.2 ~C to 0.5 ~. Both two types of curing barns exhibited uniform air distribution. Polyurethane curing barn exhibited stable vertical temperature differences. Both two types of curing barns presented good curing effects with slight differences. Polyurethane curing barn exhibited higher economic benefits, lower coal cost, lower electricity cost, lower labor cost and lon- ger service life than traditional bulk curing barn, but its construction cost was higher. [ Conclusion] Polyurethane curing barn exhibits better curing performance with ~ood application prospects.

Effects of Tobacco Curing on Accumulation of Chemical Components and Aroma Components in Tobaccos

[Objective]The aim was to explore effects of curing technique parameters on chemical components and aromatic material accumulation to formulate a suitable curing technique and for and to achieve tobacco scalding, drying and giving aromat- ic flavor. [Method] With tobacco variety KRK 26 as test materials, the test involved parameters of three curing-techniques in down, middle and upper parts of flue-cured tobaccos in an oven to measure chemical components and aromatic substances in tobaccos. [Result] The effects of curing techniques on total sugar and reducing sug- ar differed upon temperature and humidity. The contents of chemical components, such as total alkaloid, total N and the ratio of sugar/ alkali by moderate temperature and high humidity technique were of significant differences with those by moderate temperature and moderate humidity technique and with low temperature and low hu- midity technique; the chemical components by moderate temperature and moderate humidity were of insignificant differences with the treatment by low temperature and low humidity technique. Total amount of aroma components by different curing tech- niques from high to low was the treatment by low temperature and low humidity technique （461.72 μg/g）, the treatment by moderate temperature and moderate hu- midity technique （450.06μg/g） and the treatment by moderate temperature and high humidity technique （385.12μg/g）, suggesting the content of aromatic substances is high at low temperature and low humidity. [Conclusion] Moderate temperature and high humidity curing technique has significant effects on total alkaloid, total N and the ratio of sugar/ alkali of tobaccos and different curing techniques also affect the total amount of aromatic substances of flue-cured tobaccos.

Curing of the Bacillus subtilis Plasmid Using Sodium Dodecyl Sulfate

Curing of Bacillus subtilis plasmid using sodium dodecyl sulfate (SDS)was studied in order to obtain a host strain. An overnight culture of Bacillus subtilis 24/pMX45 was used to inoculate fresh LB containing SDS (0-0.008%). No growth of 24/pMX45 was observed when LB contained an SDS concentration of 0.006% or greater, and the sublethal concentration (w/v) of SDS was 0.005% with a killing rate of 99%. Samples were diluted and plated on LB agar, individual colonies were randomly picked to a selective agar medium by tooth to screen for loss of plasmid-encoded erythomycin resistance. CsCl-EtBr gradient centrifugation and plasmid DNA profile demonstrated that plasmid-cured derivative A7 has completely lost its plasmid. A7 had a shorter lag, and its cell concentration was consistently higher than that of the 24/pMX45. Elimination of the plasmid was first observed after 24/pMX45 had been treated with SDS for 8 h. The percent elimination then continued to increase until about 22 h, after which the fraction of cured cell in the population remained constant. Plasmid cured cell numbers were measured in a separate control culture of 24/pMX45 untreated by SDS. No spontaneous loss of pMX45 was observed after 24/pMX45 were incubated for 24 h and 48 h with shaking at 37 ℃.These results suggested that SDS can be used as curing agent to eliminate the plasmid of Bacillus subtilis.