Critical load position for cavities beneath CRCP slab under vehicle loading

In order to study the critical load position that causes cavities beneath the continuously reinforced concrete pavement（ CRCP） slab under vehicle loading, the elliptical load is translated into the square load based on the equivalence principle.The CRCP slab is analyzed to determine the cavity position beneath the slab under vehicle loading. The influences of cavity size on the CRCP slab＇s stress and vertical displacement are investigated. The study results showthat the formation of the cavity is unavoidable under traffic loading, and the cavity is located at the edge of the longitudinal crack and the slab corner.The cavity size exerts an obvious influence on the largest horizontal tensile stress and vertical displacement. The slab corner is the critical load position of the CRCP slab. The results can be used to assist the design of CRCP in avoiding cavities beneath slabs subject to vehicle loading.

Acid deposition critical loads modeling for the simulation of sulfur exceedance and reduction in Guangdong, China

The current acid deposition critical loads in Guangdong, China were calculated using the PROFILE model with a 3 km × 3 km resolution. Calculations were carded out for critical loads of potential acidity, actual acidity, sulfur and nitrogen, with values in extents of 0-3.5, 0-14.0, 0-26.0 and 0-3.5 kmol/（hrnE.year）, respectively. These values were comparable to previously reported results and reflected the influences of vegetation and soil characteristics on the soil acid buffering capacity. Simulations of SO2 emission and sulfur deposition in this study showed that sulfur deposition core areas mirrored SO2 emission centers. The prediction of sulfur deposition after 20% and 40% reduction of SO2 emission suggested that the reduction of area sources contributed greatly to the decrease of sulfur deposition. Thus, abatement of area source emissions could be the primary way to mitigate sulfur deposition in Guangdong to meet both the provincial and national regulations of air pollution control.

A method for predicting critical load evaluating adhesion of coatings in scratch testing

In this paper based on the experiment principle of evaluating adhesion property by scratch testing, the peeling mechanism of thin films is discussed by applying contact theory and surface physics theory. A mathematical model predicting the critical load is proposed for calculating critical load as determined byscratch testing. The factors for correctly evaluating adhesion of coatings according to the experimental data arediscussed.

Critical load of sulfur deposition for ecosystemand its application in China

ＣｒｉｔｉｃａｌｌｏａｄｏｆｓｕｌｆｕｒｄｅｐｏｓｉｔｉｏｎｆｏｒｅｃｏｓｙｓｔｅｍａｎｄｉｔｓａｐｐｌｉｃａｔｉｏｎｉｎＣｈｉｎａＺｈａｏＤｉａｎｗｕ；ＺｈａｎｇＸｉａｏｓｈａｎ；ＹａｎｇＪｉａｎｘｉｎ（ＲｅｓｅａｒｃｈＣｅｎｔｅｒｆｏｒＥｃｏ－Ｅ...

A New Proximity Indicator for Assessment of Voltage Stability and Critical Loadability Point

This paper presents a newly developed proximity indicator for voltage stability assessment which can be used to predict critical real system load and voltages at various load buses at critical loading point.The proximity indicator varies almost parabolic with total real load demand and reaches orthogonally to real load axis.This relation has been utilized to predict critical loading point.It has been shown that two operating points are needed for estimating critical point and proper selection of operating points and variation of proximity indicator near collapse point highly affect the accuracy of estimation.Simulation is based on load flow equations and system real and reactive loadings have been increased in proportion with base case scenario for IEEE 14 and IEEE 25 bus test systems to demonstrate the behaviour of proposed proximity indicator.CPF has been used as benchmark to check the accuracy of estimation.

DISCUSSION OF CRITICAL LOAD IN NONLINEAR STABILITY ANALYSIS AND SUGGESTION OF VARIATIONAL PRINCIPLE OF SOLVING CRITICAL LOADS

In this paper, a set of variational formulas of solving nonlinear instability critical loads are established from the viewpoint of variational principle. The paper shows that it is very convenient to solve nonlinear instability critical load by using the variational formulas suggested in this paper.

Analysis of Critical Load of the Orthotropic Plate Structures

Advanced design based on the concept of orthotropic structure includes better use of materials, less weight compared to the equivalent isotropic construction and controlled effectively reserve resistance in all its segments. In this case a calculation of critical load is exposed using the FDM （Finite Difference Method） concept of thin plates subjected to complex loads due to forces in the middle-plane. Results of calculation model, discussed in this paper, are given in graphic form. Presented results should serve as an indicator of the expansion of theoretical base of similar models, which can be reasonably use by researchers and engineers in their practices, and by students for educational purposes.

Centralized multi-agent implementation for securing critical loads in PV based microgrid

The promotion of recent critical load securing of power system research has been directed towards centralized commands and control functions.This paper presents a multi-agent based critical load securing in a PV based microgrid.For the trustworthy operation of critical buildings,the reliability,efficiency and security of the power system should be guaranteed.At present,to increase the security and reliability of electricity supply there is a need to design a distributed and autonomous subset of a larger grid or a microgrid.This work also clearly discusses the modelling and simulation of specialized microgrid called an Intelligent Distributed Autonomous Power Systems(IDAPS).The IDAPS microgrid plays a crucial role in constructing power grid that facilitate use of renewable energy technologies.IDAPS microgrid comprising of solar photovoltaic as distributed energy resources,different loads and their control algorithms,has been developed.Several case studies have been simulated to evaluate the operation of the IDAPS microgrid during parallel,islanded mode operation and securing critical loads during emergency.

Mapping Critical Loads of Acid Deposition for Soils in China

A method described is to produce critical load maps of acid deposition for soils in China. Critical loads were assigned to the most sensitive soil in each 0.1°×0.1° grid square of China based on the Skokloster classification [1] and adjusted for temperature and land use. The map shows that soils with small critical load (<0.5keq·ha -1 ·a -1 ) i.e., highly sensitive to acid deposition, dominate in the south and northeast China. As a result of the adjustment, much of the acid sensitive area in the south estimated by the Skokloster method is lost. This reflects the decreased sensitivity as a result of agricultural activities and increased weathering rate in response to high temperature. Based on the 0.1°×0.1° map, a series of percentile critical load maps at 1°×1° scale were compiled for integrated assessments, as well as a critical load map using the minimum critical load for each grid. Comparison of critical loads with sulphur deposition in 1995 led to the critical load exceedance maps for sulphur deposition, which show that high exceedance areas do not correlate well with the low critical load areas, and almost one fourth of the land area, mainly in the southeast, is subject to the risk of acidification.

THE INFLUENCE OF IMPERFECTIONS UPON THE CRITICAL LOAD OF STRUCTURES

By means of the theory of universal unfolding, the influence of multi-imperfections upon the critical load of structure in engineering is analysed in this paper. For the pitchfork problem, a lower bound of increments of the critical loads caused by imperfections of the structures is given. A simple and available numerical method for computing the lower bound is described.

THE SOLUTION TO THE DESTABILIZING CRITICAL LOAD OF CIRCULAR DOUBLE ARTICULATED ARCH UNDER GOING VERTICAL DISTRIBUTIVE LOAD g_0/cos^2θ

In this paper, after taking th e effect of axis force on bending into consideration, the general potential ener gy for the circular double articulated arch is established undergoing vertical d istributive load g 0/ cos 2θ . With sufficient engineering precision, the fourth approximations to the destabilizing critical load of the arch under t his load are obtained by Ritz method. The approximations to the critical load ta ble are listed for various center angles of arch, and are contrasted with the cr itical load circular arch undergoing radial uniform load. Some reference results have been obtained.

Dynamical response of hyper-elastic cylindrical shells under periodic load

Dynamical responses, such as motion and destruction of hyper-elastic cylindrical shells subject to periodic or suddenly applied constant load on the inner surface, are studied within a framework of finite elasto-dynamics. By numerical computation and dynamic qualitative analysis of the nonlinear differential equation, it is shown that there exists a certain critical value for the internal load describing motion of the inner surface of the shell. Motion of the shell is nonlinear periodic or quasi-periodic oscillation when the average load of the periodic load or the constant load is less than its critical value. However, the shell will be destroyed when the load exceeds the critical value. Solution to the static equilibrium problem is a fixed point for the dynamical response of the corresponding system under a suddenly applied constant load. The property of fixed point is related to the property of the dynamical solution and motion of the shell. The effects of thickness and load parameters on the critical value and oscillation of the shell are discussed.

Analytic Solution of Elasto-Plastic Stress in Infinite Slope under Uniform Load

According to the Mohr-Coulomb yield criterion, the stress field of the infinite slope is derived under a vertical uniform load q on the top of the slope. It is indicated that elastic and elasto-plastic states would occur in the slope. When q is smaller than the critical load, q(p), the slope is in the elastic state. If q equals q(p), the slope is in the critical state, and the plastic deformation would occur along the critical angle. With the increase of q, the plastic zone would extend, and the slope is in the elasto-plastic State. If q equals limit load, the slope is in the limit equilibrium state. The slope may be divided into three zones. Some charts of the critical angle, the critical and limit load coefficients are presented in this paper.

NONLINEAR VIBRATION OF CIRCULAR SANDWICH PLATES UNDER CIRCUMJACENT LOAD

Based on von Karman plate theory, the issue about nonlinear vibration for circular sandwich plates under circumjacent load with the loosely clamped boundary condition was researched. Nonlinear differential eigenvalue equations and boundary conditions of the problem were formulated by variational method and then their exact static solution can be got. The solution was derived by modified iteration method, so the analytic relations between amplitude and nonlinear oscillating frequency for circular sandwich plates were obtained. When circumjacent load makes the lowest natural frequency zero, critical load is obtained.

Finding the buckling load of non-uniform columns using the iteration perturbation method

The aim of this study is to calculate the critical load of variable inertia columns. The example studied in this paper can be used as a paradigm for other non-uniform columns. The wavelength of equivalent vibratory system is used to calculate the critical load of the trigonometrically varied inertia column. In doing so, the equilibrium equation of the column is theoretically studied using the perturbation method. Accuracy of the calculated results is evaluated by comparing the solution with numerical results. Effect of improving the initial guess on the solution accuracy is investigated. Effects of varying parameters of the trigonometrically varied inertia and the uniformly tapered columns on their stability behavior are studied. Finally, using the so-called ＂perfectibility＂ parameter, two design goals, i.e., being lightweight and being strong, are studied for the discussed columns.

Service Life Prediction of Lining Concrete of Subsea Tunnel under Combined Compressive Load and Carbonation

Qingdao Jiaozhou Bay subsea tunnel is the second self-built tunnel in China with the designed service life over 100 years.The durability of lining concrete are one of an important factors to determinate the service life of tunnel.Considering the main environmental loads and mechanical loads of subsea tunnel,the durability properties of lining concrete under combined action of compressive load and carbonation has been studied through the critical compressive load test,accelerated carbonation test,natural carbonation test and capillary suction test.The tests results show that critical compressive load apparently accelerates the carbonation and deteriorates the anti-permeability of concrete.Under the combined action of critical compressive load and carbonation,the durability of lining concrete decreases.Based on the carbonization life criteria and research results,for the high-performance concrete with proposed mix ratio,the predicted service life of lining concrete for Jiaozhou bay subsea tunnel is about 80 years which fails to reach the required service life.It is necessary to adopt other measurements simultaneously to improve the durability of lining concrete.

Nonlinear analysis on dynamic buckling of eccentrically stiffened functionally graded material toroidal shell segment surrounded by elastic foundations in thermal environment and under time-dependent torsional loads

The nonlinear analysis with an analytical approach on dynamic torsional buckling of stiffened functionally graded thin toroidal shell segments is investigated. The shell is reinforced by inside stiffeners and surrounded by elastic foundations in a thermal environment and under a time-dependent torsional load. The governing equations are derived based on the Donnell shell theory with the yon Karman geometrical nonlinearity, the Stein and McElman assumption, the smeared stiffeners technique, and the Galerkin method. A deflection function with three terms is chosen. The thermal parameters of the uniform temperature rise and nonlinear temperature conduction law are found in an explicit form. A closed-form expression for determining the static critical torsional load is obtained. A critical dynamic torsional load is found by the fourth-order Runge-Kutta method and the Budiansky-Roth criterion. The effects of stiffeners, foundations, material, and dimensional parameters on dynamic responses of shells are considered.

From ultra-low friction to superlubricity state of black phosphorus:Enabled by the critical oxidation and load

Based on the density functional theory(DFT),we investigate the friction properties of inevitable oxidized black phosphorus(o-BP).o-BP with the weaker interlayer adhesion exhibits their great potential as a solid lubricant.At the zero load,the friction property of o-BP is adjusted by its oxidation degree.Expressly,ultra-low friction of P4O2(50%oxidation,O:P=2:4=50%)is obtained,which is attributed to the upper O atoms with lower sliding resistance in the O channel formed by lower layer O atoms.More attractive,we observe superlubricity behavior of o-BP at the critical load/distance due to the flattening potential energy surface(PES).The flattening PES is controlled by the electrostatic role for the high-load(P4O3,O:P=3:4=75%),and by the electrostatic and dispersion roles for the low-load(P4O2).Distinctly,the transform from ultra-low friction to superlubricity state of black phosphorus(BP)can be achieved by critical oxidation and load,which shows an important significance in engineering application.In addition,negative friction behavior of o-BP is a general phenomenon(Z>Z_(min),Z_(min)is the interlayer distances between the outermost P atoms of minimum load.),while its surface-surface model is different from the fold mechanism of the tip-surface model(Z_(0)<Z<Z_(min),Z_(0)is the interlayer distances between the outermost P atoms of equilibrium state.).Thus,this phenomenon cannot be captured due to the jump effect with instability of the atomic force microscopy(AFM)(Z>Z_(min)).In summary,o-BP improves the friction performance and reduces the application limitation,comparing to graphene(Gr),MoS2,and their oxides.

Experimental Study and Fragility Analysis of Effective-Length Factors in Column Buckling

The design of columns relies heavily on the basis of Leonhard Euler’s Theory of Elastic Buckling.However,to increase the accuracy in determining the maximum critical load a column can withstand before buckling,a constant was introduced.This dimensionless coefficient is K,also known as the effective-length factor.This constant is often found in building design codes and varies in value depending on the type of column support that is applied.This paper presents experimental and analytical studies on the determination of the effective-length factor in the buckling stability of columns with partially-fixed support conditions.To this end,the accurate K value of the columns tested by the Instron Testing Machine(ITM)at California State University,Northridge’s(CSUN’s)Mechanics Laboratory is determined.The ITM is used in studying the buckling of columns where the supports are neither pinned nor fixed,and the material cross-section rather rests upon the machine while loading is applied axially.Several column specimens were tested and the experimental data were analyzed in order to estimation of the accurate effective-length factor.The calculations from the tested results as well as the conducted probabilistic analysis shed light on how a fragility curve may aid in predicting the effective-length value of future tests.

RESEARCH ON IMPERFECTION SENSITIVE REGION OF SINGLE-LAYER LATTICED DOMES

The concept of the imperfection sensitive region is given. The advanced stochastic imperfection method is used to research the imperfection sensitive region of single-layer latticed domes. Taking a K6 single-layer latticed dome with a diameter of 50 m as an example, its imperfection sensitive region is made up of the first 12 kinds of joints. The influence of the imperfections of support joints on the stability of the K6 single-layer latticed dome is negligible. Influences of the joint imperfections of the main rib and the secondary rib on the structural stability are similar. The initial deviations of these joints all greatly lower the critical load of the dome. Results show that the method can analyze the structural imperfection sensitive region quantitatively and accurately.