In situ luminescence measurements of GaN/Al_(2)O_(3) film under different energy proton irradiations

Ion beam-induced luminescence(IBIL) experiments were performed to investigate the in situ luminescence of GaN/Al_(2)O_(3) at varying ion energies,which allowed for the measurement of defects at different depths within the material.The energies of H^(+)were set to 500 keV,640 keV and 2 MeV,the Bragg peaks of which correspond to the GaN film,GaN/Al_(2)O_(3) heterojunction and Al_(2)O_(3) substrate,respectively.A photoluminescence measurement at 250 K was also performed for comparison,during which only near band edge(NBE) and yellow band luminescence in the GaN film were observed.The evolution of the luminescence of the NBE and yellow band in the GaN film was discussed,and both exhibited a decrease with the fluence of H^(+).Additionally,the luminescence of F centers,induced by oxygen vacancies,and Cr^(3+),resulting from the ^(2)E →^(4)A_(2) radiative transition in Al_(2)O_(3),were measured using 2 MeV H^(+).The luminescence intensity of F centers increases gradually with the fluence of H^(+).The luminescence evolution of Cr^(3+)is consistent with a yellow band center,attributed to its weak intensity,and it is situated within the emission band of the yellow band in the GaN film.Our results show that IBIL measurement can effectively detect the luminescence behavior of multilayer films by adjusting the ion energy.Luminescence measurement can be excited by various techniques,but IBIL can satisfy in situ luminescence measurement,and multilayer structural materials of tens of micrometers can be measured through IBIL by adjusting the energy of the inducing ions.The evolution of defects at different layers with ion fluence can be obtained.

Investigations on MoS_(2)plasma by infra-red pulsed laser irradiation in high vacuum

MoS_(2)targets were irradiated by infra-red(IR)pulsed laser in a high vacuum to determine hot plasma parameters,atomic,molecular and ion emission,and angular and charge state distributions.In this way,pulsed laser deposition(PLD)of thin films on graphene oxide substrates was also realized.An Nd:YAG laser,operating at the 1064 nm wavelength with a 5 ns pulse duration and up to a 1 J pulse energy,in a single pulse or at a 10 Hz repetition rate,was employed.Ablation yield was measured as a function of the laser fluence.Plasma was characterized using different analysis techniques,such as time-of-flight measurements,quadrupole mass spectrometry and fast CCD visible imaging.The so-produced films were characterized by composition,thickness,roughness,wetting ability,and morphology.When compared to the MoS_(2)targets,they show a slight decrease of S with respect to Mo,due to higher ablation yield,low fusion temperature and high sublimation in vacuum.The pulsed IR laser deposited Mo Sx(with 1<x<2)films are uniform,with a thickness of about 130 nm,a roughness of about 50 nm and a higher wettability than the MoS_(2)targets.Some potential applications of the pulsed IR laser-deposited Mo Sx films are also presented and discussed.

Half-integer Shapiro steps in MgB_(2) focused He ion beam Josephson junctions

Half-integer microwave induced steps(Shapiro steps)have been observed in many different Josephson junction systems,which have attracted a lot of attention because they signify the deviation of current phase relation(CPR)and uncover many unconventional physical properties.In this article,we first report the discovery of half-integer Shapiro steps in MgB_(2)focused He ion beam(He-FIB)Josephson junctions.The half-integer steps'dependence on microwave frequency,temperature,microwave power,and magnetic field is also analyzed.We find that the existence of half-integer steps can be controlled by the magnetic field periodically,which is similar to that of high temperature superconductor(HTS)grain boundary junctions,and the similarity of the microstructures between gain boundary junctions and He-FIB junctions is discussed.As a consequence,we mainly attribute the physical origin of half-integer steps in MgB_(2)He-FIB junctions to the model that a He-FIB junction is analogous to a parallel junctions'array.Our results show that He-FIB technology is a promising platform for researching CPR in junctions made of different superconductors.

功能化氮杂环卡宾聚合树脂对Cu^(2+)的吸附研究

该研究制备了功能化氮杂环卡宾聚合树脂(PNO),旨在去除废水中Cu^(2+);基于静态和动态吸附实验,研究了PNO对废水中Cu^(2+)的吸附效果。结果表明:PNO对Cu^(2+)的最佳吸附条件为吸附剂投加量100 mg、吸附时间30 min、pH值4.0~5.9、温度298 K、转速150 r/min,最大吸附量为51.55 mg/g。PNO对Cu^(2+)的吸附过程符合Langmuir、Freundlich等温吸附模型和准二级动力学模型。动态吸附量随柱高增加、流速降低和进水Cu^(2+)浓度增加而增大。使用Thomas和Bohart-Adams模型拟合,相关系数R^(2)均大于0.92,预测值与实验值相符。经过5次静态吸附-解吸和3次动态循环再生后,PNO对Cu^(2+)的去除率仍达到第一次循环的96%以上,去除效果和再生性能良好。PNO对含铜废水高效处理具有广泛的应用前景。

磁性三乙烯四胺/单宁树脂对Cu^(2+)、Pb^(2+)的吸附性能研究

利用曼尼希反应将三乙烯四胺(TETA)固化到单宁(TA)基体表面,热溶剂法制得磁性单宁基树脂(MTETA-TA)。通过红外光谱、扫描电镜、比表面积及孔隙度分析仪、振动样品磁强计对M-TETA-TA进行表征,表明M-TETA-TA具有疏水性强、比表面积大的优势,Fe_(3)O_(4)的成功引入有效解决吸附剂回收难的问题。对含Cu^(^(2+))、Pb^(2+)废水溶液进行了静态吸附实验,探讨了其对金属的吸附性能。在pH为5的酸性条件下,吸附效果较好;Cu^(^(2+))和Pb^(2+)吸附动力学均符合准二级反应动力学模型,主要为化学吸附;Cu^(^(2+))的吸附等温线符合Langmuir模型,属单层吸附,理论吸附最大值为173.33 mg·g^(-1);Pb^(2+)的吸附等温线符合Sips模型,属多层吸附,理论吸附最大值为217.14 mg·g^(-1)。推测M-TETA-TA对Pb^(2+)的吸附除了螯合、氧化还原等化学反应,还存在静电和离子交换作用,氨基和酚羟基为主要参与官能团。循环再生5次后,仍有较高的吸附性能和磁性强度。

ZIF-8/PEO杂化泡沫对TC和Cu^(2+)吸附研究

以提高金属有机骨架ZIF-8水处理中可回收性为目标,利用聚氧化乙烯PEO作为致孔剂,采用冰模板-冷冻干燥法制备金属有机骨架杂化泡沫ZIF-8/PEO,利用XRD、SEM、TG-DSC和N2吸附-脱附等表征手段,分析ZIF-8/PEO杂化泡沫的理化性能,研究ZIF-8/PEO对四环素TC和铜离子Cu^(2+)吸附性能及吸附机理。试验结果表明:ZIF-8/PEO形成了更加规则的网状结构且具有良好的机械强度和吸附性能。在吸附时间12 h,pH 7,吸附剂投加量40 mg,TC和Cu^(2+)初始浓度均为30 mg/L的最佳条件下,ZIF-8/PEO对TC和Cu^(2+)的吸附容量为107.55 mg/g和107.81 mg/g;等温吸附过程符合Langmuir模型,动力学过程符合拟二级动力学模型,ZIF-8/PEO吸附TC,Cu^(2+)属于自发、放热、趋于有序的过程。在循环吸附7次后,ZIF-8/PEO吸附剂对TC和Cu^(2+)的去除率仍在70%以上。

Fe^(2+)、Cu^(2+)诱导工艺对柞木表板颜色变化规律的影响

木材中的木质素、抽提物等物质具有能与金属盐溶液产生颜色反应的特性。利用这一特性以硫酸亚铁、硫酸铜溶液作为诱导剂,通过正交试验得到色差最大时的工艺参数,探究金属Fe^(2+)、Cu^(2+)的诱导剂质量分数、诱导时间、干燥时间、干燥温度对实木复合地板柞木表板颜色变化的影响。结果表明:Fe^(2+)、Cu^(2+)的诱导剂质量分数对柞木表板色彩色调的影响极为显著(F值分别为20.4453、8.8442);柞木表板的明度色品指数(L^(*))、红绿轴色品指数(a^(*))、黄蓝轴色品指数(b^(*))均随着Fe^(2+)、Cu^(2+)的诱导剂质量分数、诱导时间、干燥时间的增加而逐渐减少,总色差(ΔE^(*))逐渐增大,最大为31.53、9.90,表板色调逐渐偏暗、偏绿、偏蓝;随着干燥温度的增加,Fe^(2+)、Cu^(2+)诱导时的柞木表板总色差都逐渐减小。

UiO-66-NH_(2)的改性及其吸附Cu^(2+)性能

通过溶剂热法合成了锆基金属有机框架材料中的UiO-66-NH_(2),用多巴胺(DA)对其进行后合成改性,制备了UiO-66-NH_(2)/PDA复合材料,用于去除重金属Cu^(2+)。探究了pH、初始ρ(Cu^(2+))、接触时间和温度对吸附过程的影响,结果表明,Cu^(2+)的吸附动力学和等温线数据分别符合准二级和Langmuir模型,吸附过程为自发吸热反应;初始ρ(Cu^(2+))=50 mg/L,pH=5.5,t<30 min,Cu^(2+)去除率为93%。

不同质量浓度Cu^(2+)和Ag^(+)对大麦成熟胚组培特性的影响

【目的】探究不同质量浓度Cu^(2+)和Ag^(+)对大麦成熟胚组培特性的影响。【方法】以Bowman、北青7号和光头大麦的成熟胚为材料,研究不同质量浓度Cu^(2+)和Ag^(+)对大麦成熟胚愈伤诱导率、长根率、长芽率、褐化率、绿化率、再分化率和愈伤湿质量的影响。【结果】Bowman、北青7号和光头大麦成熟胚的7种组培特性间存在不同程度差异。与对照相比,0.75 mg/L Cu^(2+)可减少10.43%的成熟胚长根、7.48%的成熟胚长芽、8.24%的愈伤组织褐化、20.74 mg的愈伤湿质量;4.00 mg/L Ag^(+)可提高6.47%的愈伤组织诱导率,可减少9.08%的成熟胚长根、7.96%的成熟胚长芽和9.67%的愈伤褐化;0.75 mg/L Cu^(2+)和4.00 mg/L Ag^(+)对愈伤细胞转绿、愈伤增殖和再分化均无抑制。【结论】适宜质量浓度的Cu^(2+)和Ag^(+)可有效抑制大麦成熟胚长根、长芽和愈伤组织褐化,Ag+还可有效提高愈伤诱导率;在基于MS培养基的大麦成熟胚愈伤组织诱导和再分化培养中,Cu^(2+)和Ag^(+)的适宜质量浓度分别为0.75和4.00 mg/L。研究结果可为构建大麦成熟胚的愈伤诱导及其再分化技术体系提供理论支持。

钠化污泥生物炭复合凹凸棒石对水体中Cu^(2+)的吸附效果研究

含铜废水严重威胁人体健康和环境安全,利用废弃污泥和凹凸棒石制备了钠化污泥生物炭复合凹凸棒石材料,并将其用于含Cu^(2+)废水的处理。利用SEM、XRD及FT-IR对材料的结构和表面性质进行了分析表征,复合材料表面的含氧官能团的络合或C=C键的Π电子作用是吸附重金属的主要机制。研究了复合材料对Cu^(2+)的吸附效果和机理,结果表明,污泥/凹凸棒石质量比2∶1,pH=5,添加量为1.5 g/L,Cu^(2+)初始浓度4 mg/L条件下,材料对Cu^(2+)有最大的吸附容量为3.339 mg/g。吸附过程更好地拟合了准二级动力学模型和Langmuir吸附等温式,表明材料对Cu^(2+)的吸附是单分子层化学吸附。利用响应面分析法预测,pH值为5.04,吸附剂添加量1.16 g/L,Cu^(2+)初始浓度3.60 mg/L是最佳吸附条件。钠化污泥生物炭复合凹凸棒石在实际含铜废水处理中是一种极具潜力的吸附剂。

用于吸附养殖尾水中Cu^(2+)的温度敏感型淀粉基水凝胶制备及性能分析

为了快速移除水产养殖尾水中的铜离子(Cu^(2+)),合成了一种新型温度敏感多糖基水凝胶,以具有结构和性能优势的2-羟基-3-异丙氧基丙基淀粉醚(HIPS)和羧甲基淀粉钠(CMS)为原料,以乙二醇二缩水甘油醚(EDGE)和CaCl 2为交联剂,通过形成共价键和离子键的混合交联方式制备具有温度敏感性能的HIPS/CMS复合凝胶,利用傅里叶转换红外光谱(FT-IR)、扫描电镜(SEM)对复合凝胶的结构和内部形貌进行表征,研究复合凝胶的温度敏感性能,并探究了复合凝胶对水产养殖尾水中Cu^(2+)的吸附效果。结果表明:HIPS/CMS复合凝胶具有优异的温度敏感性能,当温度高于其体积相转变温度(VPTT,34.1℃)时,复合凝胶体积明显收缩,溶胀率从62.1倍下降至33.6倍;HIPS/CMS复合凝胶对水产养殖尾水中Cu^(2+)具有良好的吸附性能,最大吸附量可达25.2 mg/g;复合凝胶对Cu^(2+)吸附过程符合Langmuir吸附模型,属于单分子层化学吸附;利用该复合凝胶的温度敏感性能,可实现HIPS/CMS复合凝胶的回收再利用,并且经5次吸附-解吸循环后吸附量仍可达15.1 mg/g。研究表明,本研究制备的HIPS/CMS复合凝胶对养殖尾水中的Cu^(2+)的去除效果较好且绿色环保,可以重复使用。

Cu^(2+)污染原状黄土的物化及结构特性

为制定环境保护和土壤污染防治和修复策略,以及为污染场地工程建设提供理论支撑,该文研究了Cu^(2+)对原状黄土物化特性及结构特性的影响。通过制备不同掺量的Cu^(2+)污染黄土试样,进行了粒径分布、CaCO_(3)含量和pH值的测定。利用扫描电镜和激光粒度仪获得试样的SEM图像和粉粒各粒径含量,并借助分形理论深入分析了Cu^(2+)对原状黄土微观结构的影响机理。对Cu^(2+)污染的原状黄土试样进行了压缩试验,并对试样的综合结构势进行了分析。结果表明,随着Cu^(2+)掺量的增大,黏粒含量表现为先增后减,再增再减的趋势,粉粒含量则表现为先减后增,再减再增,砂粒含量保持不变;CaCO_(3)的含量呈线性减小;pH值先迅速减小,后保持不变;污染黄土试样的综合结构势先增大后减小,之后再增大再减小。总体而言,重金属Cu^(2+)的掺入,导致土壤pH值降低,主要胶结物质碳酸钙被溶解,而又因黏粒之间的静电引力和范德华力,黏粒聚集体的形态和成分发生变化,从而影响了土体的密实度和结构强度。

Co-doped BaFe_(2)As_(2) Josephson junction fabricated with a focused helium ion beam

Josephson junction plays a key role not only in studying the basic physics of unconventional iron-based superconductors but also in realizing practical application of thin-film based devices,therefore the preparation of high-quality iron pnictide Josephson junctions is of great importance.In this work,we have successfully fabricated Josephson junctions from Co-doped BaFe_(2)As_(2)thin films using a direct junction fabrication technique which utilizes high energy focused helium ion beam(FHIB).The electrical transport properties were investigated for junctions fabricated with various He^(+)irradiation doses.The junctions show sharp superconducting transition around 24 K with a narrow transition width of 2.5 K,and a dose correlated foot-structure resistance which corresponds to the effective tuning of junction properties by He^(+)irradiation.Significant J_c suppression by more than two orders of magnitude can be achieved by increasing the He^(+)irradiation dose,which is advantageous for the realization of low noise ion pnictide thin film devices.Clear Shapiro steps are observed under 10 GHz microwave irradiation.The above results demonstrate the successful fabrication of high quality and controllable Co-doped BaFe_(2)As_(2)Josephson junction with high reproducibility using the FHIB technique,laying the foundation for future investigating the mechanism of iron-based superconductors,and also the further implementation in various superconducting electronic devices.

Hierarchically Structured Nb_(2)O_5 Microflowers with Enhanced Capacity and Fast-Charging Capability for Flexible Planar Sodium Ion Micro-Supercapacitors

Planar Na ion micro-supercapacitors(NIMSCs) that offer both high energy density and power density are deemed to a promising class of miniaturized power sources for wearable and portable microelectron-ics. Nevertheless, the development of NIMSCs are hugely impeded by the low capacity and sluggish Na ion kinetics in the negative electrode.Herein, we demonstrate a novel carbon-coated Nb_(2)O_5 microflower with a hierarchical structure composed of vertically intercrossed and porous nanosheets, boosting Na ion storage performance. The unique structural merits, including uniform carbon coating, ultrathin nanosheets and abun-dant pores, endow the Nb_(2)O_5 microflower with highly reversible Na ion storage capacity of 245 mAh g^(-1) at 0.25 C and excellent rate capability.Benefiting from high capacity and fast charging of Nb_(2)O_5 microflower, the planar NIMSCs consisted of Nb_(2)O_5 negative electrode and activated car-bon positive electrode deliver high areal energy density of 60.7 μWh cm^(-2),considerable voltage window of 3.5 V and extraordinary cyclability. Therefore, this work exploits a structural design strategy towards electrode materials for application in NIMSCs, holding great promise for flexible microelectronics.

两种磁性生物炭耦合Diaphorobacter sp.DFA4去除2,4-DFA和Cu^(2+)的特性

以橘子皮为原料,氯化铁、镍锰铁氧体为磁性介质,制备了氯化铁和镍锰铁氧体改性生物炭(分别记为FBC和MBC),重点考察FBC和MBC介导Diaphorobacter sp.DFA4耦合体系去除2,4-二氟苯胺(2,4-DFA)和Cu^(2+)的特性。结果表明:在0.5~2.0 g/L FBC/MBC的介导作用下,Diaphorobacter sp.DFA4对2,4-DFA和Cu^(2+)的去除效果明显提升。当2,4-DFA初始质量浓度为100~900 mg/L时,相比纯菌Diaphorobacter sp.DFA4培养体系,FBC和MBC介导耦合体系对2,4-DFA的降解强化倍数分别为2.24~4.04倍和1.96~4.71倍,Cu^(2+)去除率则分别由59.70%~69.95%提升至88.57%~93.20%和82.12%~88.20%。当pH为6.0~8.0时,较纯菌Diaphorobacter sp.DFA4培养体系,MBC、FBC介导耦合体系对2,4-DFA的去除率分别提高了15.35%~36.32%和22.43%~37.42%,对Cu^(2+)的去除率则分别提高了37.63%~42.34%和43.61%~47.83%;当盐度由0提高至4%时,两个耦合体系对2,4-DFA的去除率基本保持在85%及以上,而纯菌Diaphorobacter sp.DFA4培养体系对2,4-DFA的去除率则由77.98%降至55.19%。机理分析发现,耦合体系可诱导分泌更多的腐殖酸,且在偏碱条件下,FBC更有利于促使腐殖酸的分泌。

5-磷酸吡哆醛缩合罗丹明B席夫碱合成及对Cu^(2+)的识别研究

合成了吡哆醛-5-磷酸罗丹明B席夫碱.通过紫外-可见光光谱法研究了该化合物对Cu^(2+)的识别能力:在丙酮-水(体积比1∶1)混合体系中,加入Cu^(2+)后,在526 nm处出现了一个新的吸收峰,并且随着Cu^(2+)的加入,吸收强度逐渐增强.在(0.25~10)×10^(-6) mol/L的浓度范围内,检测结果呈现出良好的线性关系(R^(2)=0.9993),检测限为2.30×10^(-7) mol/L.

Delving into the dissimilarities in electrochemical performance and underlying mechanisms for sodium and potassium ion storage in N-doped carbon-encapsulated metallic Cu_(2)Se nanocubes

The large volumetric variations experienced by metal selenides within conversion reaction result in inferior rate capability and cycling stability,ultimately hindering the achievement of superior electrochemical performance.Herein,metallic Cu_(2)Se encapsulated with N-doped carbon(Cu_(2)Se@NC)was prepared using Cu_(2)O nanocubes as templates through a combination of dopamine polymerization and hightemperature selenization.The unique nanocubic structure and uniform N-doped carbon coating could shorten the ion transport distance,accelerate electron/charge diffusion,and suppress volume variation,ultimately ensuring Cu_(2)Se@NC with excellent electrochemical performance in sodium ion batteries(SIBs)and potassium ion batteries(PIBs).The composite exhibited excellent rate performance(187.7 mA h g^(-1)at 50 A g^(-1)in SIBs and 179.4 mA h g^(-1)at 5 A g^(-1)in PIBs)and cyclic stability(246,8 mA h g^(-1)at 10 A g^(-1)in SIBs over 2500 cycles).The reaction mechanism of intercalation combined with conversion in both SIBs and PIBs was disclosed by in situ X-ray diffraction(XRD)and ex situ transmission electron microscope(TEM).In particular,the final products in PIBs of K_(2)Se and K_(2)Se_(3)species were determined after discharging,which is different from that in SIBs with the final species of Na_(2)Se.The density functional theory calculation showed that carbon induces strong coupling and charge interactions with Cu_(2)Se,leading to the introduction of built-in electric field on heterojunction to improve electron mobility.Significantly,the theoretical calculations discovered that the underlying cause for the relatively superior rate capability in SIBs to that in PIBs is the agile Na~+diffusion with low energy barrier and moderate adsorption energy.These findings offer theoretical support for in-depth understanding of the performance differences of Cu-based materials in different ion storage systems.

粉煤灰基P型沸石吸附水中Cu^(2+)和Cd^(2+)

以粉煤灰(FA)为原料经水热反应合成了P型沸石(Z-P).采用X射线荧光光谱仪、X射线衍射仪、场发射环境扫描电子显微镜、比表面孔径分析仪、傅里叶变换红外光谱仪和X射线光电子能谱对Z-P进行表征,并研究了其对Cu^(2+)和Cd^(2+)的吸附性能.结果表明,Z-P的BET比表面积和孔隙体积分别为38.46m^(2)/g和0.2180cm^(3)/g,均高于FA的1.273m^(2)/g和0.0120cm^(3)/g.FA、Z-P对Cu^(2+)和Cd^(2+)的吸附更符合拟二级动力学模型和Langmuir等温线模型.Z-P对Cu^(2+)和Cd^(2+)的最大吸附量分别为157.48,131.57mg/g,远高于于FA的30.88,25.47mg/g.Z-P对Cd^(2+)的循环再生吸附效果好,但对Cu^(2+)的循环再生吸附效果较差.离子强度对Z-P吸附Cu^(2+)和Cd^(2+)分别起促进和抑制作用.表明Z-P可以作为有效且廉价的Cu^(2+)、Cd^(2+)吸附剂,为FA的资源化利用和含Cu^(2+)、Cd^(2+)重金属离子废水吸附剂的开发提供了一种方法.

纳米SiO_(2)粒子表面接枝共聚合物微球的制备及其吸附Cu^(2+)性能

采用KH570对纳米SiO_(2)进行改性,将其作为Pickering乳液的稳定剂;利用反相(Pickering)乳液聚合法制备SiO_(2)@丙烯酰胺(AM)-丙烯酸(AA)共聚物复合微球,并对改性前后纳米SiO_(2)以及复合微球的结构、形貌及质量损失进行了表征;探究pH值、温度和单体比例对复合微球吸附Cu^(2+)效果影响,并对吸附过程进行动力学和吸附等温线拟合。结果表明,改性后的纳米SiO_(2)亲油性增强,提高稳定乳液的能力;Cu^(2+)吸附实验表明,复合微球吸附的最佳pH值为6,且吸附量随着AA用量增加而增大;复合微球吸附Cu^(2+)的过程符合准二级动力学模型和Langmuir模型。

In Situ Growth of 2D Metal–Organic Framework Ion Sieve Interphase for Reversible Zinc Anodes

Zinc metal anodes are gaining popularity in aqueous electrochemical energy storage systems for their high safety,cost-effectiveness,and high capacity.However,the service life of zinc metal anodes is severely constrained by critical challenges,including dendrites,water-induced hydrogen evolution,and passivation.In this study,a protective two-dimensional metal–organic framework interphase is in situ constructed on the zinc anode surface with a novel gel vapor deposition method.The ultrathin interphase layer(~1μm)is made of layer-stacking 2D nanosheets with angstrom-level pores of around 2.1Å,which serves as an ion sieve to reject large solvent–ion pairs while homogenizes the transport of partially desolvated zinc ions,contributing to a uniform and highly reversible zinc deposition.With the shielding of the interphase layer,an ultra-stable zinc plating/stripping is achieved in symmetric cells with cycling over 1000 h at 0.5 mA cm−2 and~700 h at 1 mA cm^(−2),far exceeding that of the bare zinc anodes(250 and 70 h).Furthermore,as a proof-of-concept demonstration,the full cell paired with MnO_(2) cathode demonstrates improved rate performances and stable cycling(1200 cycles at 1 A g−1).This work provides fresh insights into interphase design to promote the performance of zinc metal anodes.