CMOS Automatic Gain Control Circuit with DC Offset Cancellation for FM/cw Ladar

This paper presented an automatic gain control （AGC） circuit suitable for FM/cw ladar. The proposed architecture was based on two-stage variable gain amplifier （VGA） chain with a novel DC offset canceller circuit, which contained an improved Gilbert cell and a Gm-C feedback loop. To keep the VGA with a linearity in dB characteristic, an improved exponential gain control circuit was introduced. The AGC was implemented in 0.18 gm standard CMOS process. Simulation and measurement results verified that its gain ranged from -20 dB to 30 dB, and band- width ranged from 100 kHz to 10 MHz. Its power consumption was 19.8 mW under a voltage supply of 3.3 V.

A novel analog/digital reconfigurable automatic gain control with a novel DC offset cancellation circuit

An analog/digital reconfigurable automatic gain control （AGC） circuit with a novel DC offset cancel- lation circuit for a direct-conversion receiver is presented. The AGC is analog/digital reconfigurable in order to be compatible with different baseband chips. What＇s more, a novel DC offset cancellation （DCOC） circuit with an HPCF （high pass cutoff frequency） less than 10 kHz is proposed. The AGC is fabricated by a 0.18μm CMOS process. Under analog control mode, the AGC achieves a 70 dB dynamic range with a 3 dB-bandwidth larger than 60 MHz. Under digital control mode, through a 5-bit digital control word, the AGC shows a 64 dB gain control range by 2 dB each step with a gain error of less than 0.3 dB. The DC offset cancellation circuits can suppress the output DC offset voltage to be less than 1.5 mV, while the offset voltage of 40 mV is introduced into the input. The overall power consumption is less than 3.5 mA, and the die area is 800 ×300μm2.

CMOS linear-in-dB VGA with DC offset cancellation for direct-conversion receivers

A low-power high-linearity linear-in-dB variable gain amplifier（VGA） with novel DC offset calibration loop for direct-conversion receiver（DCR） is proposed.The proposed VGA uses the differential-ramp based technique,a digitally programmable gain amplifier（PGA） can be converted to an analog controlled dB-linear VGA. An operational amplifier（OPAMP） utilizing an improved Miller compensation approach is adopted in this VGA design.The proposed VGA shows a 57 dB linear range.The DC offset cancellation（DCOC） loop is based on a continuous-time feedback that includes the Miller effect and a linear range operation MOS transistor to realize high-value capacitors and resistors to solve the DC offset problem,respectively.The proposed approach requires no external components and demonstrates excellent DCOC capability in measurement.Fabricated using SMIC 0.13μm CMOS technology,this VGA dissipates 4.5 mW from a 1.2 V supply voltage while occupying 0.58 mm^2 of chip area including bondpads.In addition,the DCOC circuit shows 500 Hz high pass cutoff frequency（HPCF） and the measured residual DC offset at the output of VGA is less than 2 mV.

A programmable gain amplifier with digitally assisted DC offset calibration for a direct-conversion WLAN receiver

This paper presents a programmable gain amplifier（PGA） circuit with a digitally assisted DC offset cancellation（DCOC） scheme for a direct conversion WLAN receiver.Implemented in a standard 0.13-μm CMOS process,the PGA occupies 0.39 mm2 die area and dissipates 6.5 mW power from a 1.2 V power supply.By using a single loop single digital-to-analog converter（DAC） mixed signal DC offset cancellation topology,the minimum DCOC settling time achieved is as short as 1.6μs with the PGA gain ranging from -8 to 54 dB in a 2 dB step.The DCOC loop utilizes a segmented DAC structure to lower the design complexity without sacrificing accuracy and a digital control algorithm to dynamically set the DCOC loop to fast or normal response mode,making the PGA circuit in compliance with the targeted WLAN specifications.

A baseband circuit for wake-up receivers with double-mode detection and enhanced sensitivity robustness

This paper proposes a baseband circuit for wake-up receivers with double-mode detection and enhanced sensitivity robustness for use in the electronic toll collection system.A double-mode detection method,including amplitude detection and frequency detection,is proposed to reject interference and reduce false wake-ups.An improved closed-loop band-pass filter and a DC offset cancellation technique are also newly introduced to enhance the sensitivity robustness.The circuit is fabricated in TSMC 0.18μm 3.3 V CMOS technology with an area of 0.12 mm2.Measurement results show that the sensitivity is -54.5 dBm with only a±0.95 dBm variation from the 1.8 to 3.3 V power supply,and that the temperature variation of the sensitivity is±1.4 dBm from -50 to 100℃. The current consumption is 1.4 to 1.7μA under a 1.8 to 3.3 V power supply.

A high dynamic range linear RF power detector with a preceding LNA

A design of high dynamic range linear radio frequency power detector （PD）, aimed for transmitter carrier leakage suppression is presented in this paper. Based on the logarithmic amplifier principle, this detector utilizes the successive detection method to achieve a high dynamic range in the radio frequency band. In order to increase sensitivity, a low noise amplifier （LNA） is placed in the front of this detector. DC coupling is adopted in this architecture to reduce parasitics and save area, but this will unavoidably cause DC offsets in the circuit which are detrimental to the dynamic range. So a DC offset cancelling （DCOC） technique is proposed to solve the problem. Finally, this detector was fabricated in the SMIC 0.13μm CMOS process. The measured results show that it achieves a wide dynamic range of 50 dB/40 dB with log errors in 4-1 dB at 900 MHz/2 GHz, while draws 16 mA from a 1.5 V power supply. The active chip area is 0.27×0.67 mm2.