Determination of Natural Logarithm of Diffusion Coefficient and Activation Energy of Thin Layer Drying Process of Ginger Rhizome Slices

This study is an extension of the previous work done with ARS-680 Environmental Chamber. Drying is a complex operation that demands much energy and time. Drying is essentially important for preservation of ginger rhizome. Drying of ginger was modeled, and then the effective diffusion coefficient and activation energy were determined. For this purpose, the experiments were done at six levels of varied temperatures: 10°C, 20°C, 30°C, 40°C, 50°C and 60°C. The values of effective diffusion coefficients obtained in this work for the variously treated ginger rhizomes closely agreed with the average effective diffusion coefficients of other notable authors who determined the drying kinetics and convective heat transfer coefficients of ginger slices.

Effect of different drying methods on the amino acids,α-dicarbonyls and volatile compounds of rape bee pollen

The significant demand for high quality food has motivated us to adopt appropriate processing methods to improve the food nutritional quality and flavors.In this study,the effects of five drying methods,namely,pulsed vacuum drying(PVD),freeze drying(FD),infrared drying(IRD),hot-air drying(HAD)and sun drying(SD)on free amino acids(FAAs),α-dicarbonyl compounds(α-DCs)and volatile compounds(VOCs)in rape bee pollen(RBP)were determined.The results showed that FD significantly released the essential amino acids(EAAs)compared with fresh samples while SD caused the highest loss.Glucosone was the dominantα-DCs in RBP and the highest loss was observed after PVD.Aldehydes were the dominant volatiles of RBP and SD samples contained more new volatile substances(especially aldehydes)than the other four drying methods.Comprehensively,FD and PVD would be potential methods to effectively reduce the quality deterioration of RBP in the drying process.

Effect of drying cracks on swelling and self-healing of bentonite-sand blocks used as engineered barriers for radioactive waste disposal

Experiments were conducted to evaluate the healing of drying cracks in air-dried bentonite-sand blocks after hydration and swelling in groundwater,providing justifications to simplify the protection of blocks prior to installation in a high-level radioactive waste repository.Synthetic groundwater was prepared to represent the geochemistry of Beishan groundwater,and was used to hydrate the blocks during the swelling pressure and swelling strain measurements,as Beishan is the most promising site for China's repository.Healing of the surface cracks was recorded by photography,and healing of the internal cracks was visualized by CT images and hydraulic conductivity of air-dried blocks.The results indicate that the maximum swelling pressure and swelling strain are primarily affected by the geochemistry of Beishan groundwater,but not affected by the drying cracks.The maximum swelling pressure and swelling strain of air-dried blocks are comparable to or even higher than the pressure and strain of fresh blocks.The maximum swelling pressure measured in strong(i.e.high ion strength)Beishan groundwater was 44%of the pressure measured in deionized(DI)water,and the maximum swelling strain was reduced to 23%of the strain measured in DI water.Nevertheless,the remained swelling of the blocks hydrated in strong Beishan groundwater was sufficient to heal the surface and internal drying cracks,as demonstrated by the pictures of surface cracks and CT images.The hydraulic conductivity of the air-dried block permeated with strong groundwater was comparable(3.7×higher)to the hydraulic conductivity of the fresh block,indicating the self-healing of drying cracks after hydration and swelling in groundwater.A simplified method of protecting the block with plastic wraps before installation is recommended,since the remained swelling of the block hydrated in Beishan groundwater is sufficient to heal the drying cracks.

Wetting alternating with partial drying during grain filling increases lysine biosynthesis in inferior rice grain

Lysine content is a criterion of the nutritional quality of rice.Understanding the process of lysine biosynthesis in early-flowering superior grain(SG)and late-flowering inferior grain(IG)of rice would advance breeding and cultivation to improve nutritional quality.However,little information is available on differences in lysine anabolism between SG and IG and the underlying mechanism,and whether and how irrigation regimes affect lysine anabolism in these grains.A japonica rice cultivar was grown in the field and two irrigation regimes,continuous flooding(CF)and wetting alternating with partial drying(WAPD),were imposed from heading to the mature stage.Lysine content and activities of key enzymes of lysine biosynthesis,and levels of brassinosteroids(BRs)were lower in the IG than in the SG at the early grainfilling stage but higher at middle and late grain-filling stages.WAPD increased activities of these key enzymes,BR levels,and contents of lysine and total amino acids in IG,but not SG relative to CF.Application of 2,4-epibrassinolide to rice panicles in CF during early grain filling reproduced the effects of WAPD,but neither treatment altered the activities of enzymes responsible for lysine catabolism in either SG or IG.WAPD and elevated BR levels during grain filling increased lysine biosynthesis in IG.Improvement in lysine biosynthesis in rice should focus on IG.

Solvent transport dynamics and its effect on evolution of mechanical properties of nitrocellulose(NC)-based propellants under hot-air drying process

Appropriate drying process with optimized controlling of drying parameters plays a vital role in the improvement of the quality and performance of propellant products.However,few research on solvent transport dynamics within NC-based propellants was reported,and its effect on the evolution of mechanical properties was not interpreted yet.This study is conducted to gain a comprehensive understanding of hot-air drying for NC-based propellants and clarify the effect of temperature on solvent transport behavior and further the change of mechanical properties during drying.The drying kinetic curves show the drying time required is decreased but the steady solvent content is increased and the drying rate is obviously increased with the increase of hot-air temperatures,indicating hot-air temperatures have a significant effect on drying kinetics.A modified drying model was established,and results show it is more appropriate to describe solvent transport behavior within NC-based propellants.Moreover,two linear equations were established to exhibit the relationship between solvent content and its effect on the change of tensile properties,and the decrease of residual solvent content causes an obvious increase of tensile strength and tensile modulus of propellant products,indicating its mechanical properties can be partly improved by adjustment of residual solvent content.The outcomes can be used to clarify solvent transport mechanisms and optimize drying process parameters of double-based gun propellants.

Short Communication: Enhancing the Drying Process of Microbial-Based Products with a Dehumidifier

The development of microbial-based products requires certain criteria for them to be successfully commercialized. The product must meet the following desirable criteria: effectiveness, contamination free, stability, cost-effectiveness, and a prolonged shelf life. Controlling the drying process is crucial for ensuring the stability and durability of the product. The traditional approach, which involved mechanical and natural drying, led to decreased productivity and quality. The objective of this research endeavour was to achieve a dry process enhancement while preserving the microbial quality of Trichoderma asperellum (M103). The temperature and relative humidity during the drying period were monitored under two conditions: with and without a dehumidifier. The results demonstrate that the dehumidifier increases drying period efficiency by up to 63%.

Investigation on Effect of Composition on the Drying of Castables with Cement Binder

Monolithic refractory castables comprising a hydraulic bond are still used in a vast majority of cases because of their flexibility and robustness,despite many developments for chemical as well as non-cement castable binders.The drying can however be a challenge,in particular for deflocculated dense castables of the low cement castable range.Many publications have been released on this topic for the last ten years,but they often focused on the drying mechanisms or on the addition of drying aids.This paper presents some experimental results on the effect of the composition on the drying properties,especially on the effect of silicon carbide,used for its high thermal conductivity,and on the matrix system.It also introduces two laboratory tests to study and iteratively improve the drying schedule of a given castable lining.The results show that the spalling resistance and the vapor pressure build-up are significantly influenced by the formulation.It is also shown that the castable properties after drying can be altered if the heating rate is very high.

The Role of the Size Effect on the Drying of Refractory Castables—How Its Under-standing Could Narrow the Gap between Laboratory Studies and Industrial Reality

Refractories have unique capabilities such as sustaining their shape and properties at extreme conditions such as the combination of high temperatures and thermal shock,contact with molten metals and slags and in some circumstances resistance to erosion from abrasive particles.Given the large processing output of the heavy industries such as the cement and steel ones which both require high temperature processes,the refractories structures span various meters and weight of several tons.As the water removal stage of hydraulic bonded castables in industrial sites takes hours(10-60 h)due to the risk of explosive spalling,efforts to mitigate it are commonly studied.This has provided theoretical understanding of the general aspects of drying and important tools,such as the thermogravimetry analysis(TGA),for the design of refractory compositions with higher explosive spalling resistance.However,the optimization of this process is still far from the industrial reality especially because the actual linings that require the drying are orders of magnitude larger than the samples considered in the laboratory tests.Therefore,this study proposed the analysis of the sample volume effect on the water removal dynamics through TGA of high alumina castables with calcium aluminate cement.Conventionalφ5 cm×5 cm cylindrical samples were assessed in a laboratory scale equipment whereas macro TGA were carried out considering 20 cm×20 cm×20 cm and 30 cm×30 cm×30 cm cubic samples.Additionally,the effect of polymeric fibers was also considered.It was found out that the different thermal gradients within the macro TGA samples resulted in an inflection on the sample’s heating rate and that the mass loss was affected by the volume considered,especially for the composition without additives.These findings highlight the requirement of carefully taking into consideration the different dimensional sizes and thermal gradients in the samples when analyzing and interpreting the laboratory studies,and especially when trying to extrapolate such results to the industrial reality.

Modeling the Drying Kinetics of Pigeon Pea [Cajanus cajan (L.) Millspaugh]

We set out to model the oven-drying kinetics of a legume known as pigeon pea, harvested in the Bouenza department in the south-west of the Republic of Congo. The drying kinetics of pigeon peas was carried out in an oven under experimental conditions using temperatures of: 50°C, 60°C and 70°C. Seven mathematical models were used to describe pigeon pea drying. During drying, water loss was faster and shorter at 70°C [10.446 g/25 g wet weight (wwb) for 320 min (5.3 h)] compared to 50°C [10.996 g/25 g wet weight (wwb) for 520 min (8.6 h)] and 60°C [10.616 g/25 g wet weight (wwb) for 420 min (7.0 h)] where it was slower and longer. With regard to modeling, and based on the principle of choosing the right model focusing on the high value of R2 and low values of χ2 and RMSE, two models were selected, the Midili model for temperatures of 50°C and 60°C and the Henderson and Pabis model modified for temperature of 70°C showed better results. The R2, χ2 and RMSE values calculated for pigeon pea are 0.99985, 3.93404E-5 and 0.00627;0.9997, 9.245E-5 and 0.00962;0.99996, 1.56332E-5 and 0.00395 respectively at 50°C, 60°C and 70°C.

Effect of different drying methods on the taste and volatile compounds,sensory characteristics of Takifugu obscurus

Pufferfish is prone to deterioration due to abundant nutrients and high moisture content.Drying technology can extend the shelf life and enhance the flavor quality of aquatic products.The study investigated the effect of hot air drying(HAD),microwave vacuum drying(MVD)and hot air assisted radio frequency drying(HARFD)on the taste and volatile profiles of Takifugu obscurus.Different drying methods had significant influence on the color,rehydration,5’-nucleotides,free amino acids and volatile components(P<0.05).The results showed that HAD and HARFD could promote the flavor of T.obscurus by producing higher equivalent umami concentration(EUC)values,which were about two times of MVD group,and more pronounced pleasant odor according to sensory analysis.HAD is more appropriate for industrial application than HARFD and MVD considering the economic benefits.This study could provide a reference for the industrial application of drying T.obscurus.

Asymmetric Drying and Wetting Trends in Eastern and Western China

As an important factor that directly affects agricultural production, the social economy, and policy implementation,observed changes in dry/wet conditions have become a matter of widespread concern. However, previous research has mainly focused on the long-term linear changes of dry/wet conditions, while the detection and evolution of the non-linear trends related to dry/wet changes have received less attention. The non-linear trends of the annual aridity index, obtained by the Ensemble Empirical Mode Decomposition(EEMD) method, reveal that changes in dry/wet conditions in China are asymmetric and can be characterized by contrasting features in both time and space in China. Spatially, most areas in western China have experienced transitions from drying to wetting, while opposite changes have occurred in most areas of eastern China. Temporally, the transitions occurred earlier in western China compared to eastern China. Research into the asymmetric spatial characteristics of dry/wet conditions compensates for the inadequacies of previous studies, which focused solely on temporal evolution;at the same time, it remedies the inadequacies of traditional research on linear trends over centennial timescales. Analyzing the non-linear trend also provides for a more comprehensive understanding of the drying/wetting changes in China.

Infuences of Different Admixtures on the Drying Shrinkage Characteristics of Metakaolin-based Geopolymer Mortar

To investigate the influences of different admixtures on the drying shrinkage of polymer mortar in a metakaolin base,the experiments of VAE(vinyl acetate ethylene copolymer),APAM(anionic polyacrylamide)and CPAM(cationic polyacrylamide)on the drying shrinkage properties of geopolymer mortar were designed under normal temperature curing conditions.An SP-175 mortar shrinkage dilatometer was introduced to measure the dry shrinkage of geopolymer mortar.Meanwhile,the drying shrinkage properties of geopolymer mortar are exhibited by the parameters of water loss rate,drying shrinkage rate,drying shrinkage strain and drying shrinkage coefficient.The experimental data are further fitted to obtain the prediction model of dry shrinkage of geopolymer mortar,which can better reflect the relationship between dry shrinkage rate and time.Finally,the experimental results demonstrate that the dry shrinkage of geopolymer mortar can be significantly increased by adding 4%VAE admixture,meanwhile under the condition that the polymer film formed by VAE reaction can strengthen and toughen the mortar.2.5%APAM admixture and 1.5%CPAM admixture can enhance the dry shrinkage performance of geopolymer mortar in a certain range.

Analysis of the Influence of Different Drying Methods on the Active Ingredients of Fresh Medicine

The heating area of the material is large and the thermal efficiency is high,but it is n ecessary to control the suitable drying temperature ofdiffere nt medici nal materials to preserve the effective in gredients.D iff ere nt kinds of Chinese medicine need different drying conditions to fulfill good drying requirements.Natural drying in the shade is one of the traditional drying methods,which takes a long time and is easily affected by the weather.The water volatilizes slowly.It is prone to mildew and discoloration during the drying process.However,it can better preserve the volatile oil components of Chinese medicine.The hot-air drying machine has lower requirements.The medicinal materials have a large heating area and high thermal efficiency,but it is necessary to control the appropriate drying temperature of different medicinal materials in order to preserve the active ingredients of the medicinal materials;it is not suitable for medicinal materials that stick and bind easily.The microwave drying method possesses superiority in drying some valuable medicinal materials such as Ren she n(Radix et Rhizoma Ginseng)and Lurong(Co「nu Cervi Pantotrichum),and the effective ingredients are preserved at a high degree;it can also achieve the purpose of killing enzymes and protecting glycosides and have a good bactericidal effect,but it is not suitable for Chinese medicines containing heat-sensitive ingredients,because it will destroy most of the proteins,amino acids,and peptides of Chinese medicine and result in the loss of efficacy.The far-infrared drying method is suitable for drying thin-layer medicinal materials and is friendly to the environment.Freeze-drying can preserve the active ingredients very well and greatly retain the efficacy,but it has obvious limitations in preserving some Chinese medicinal materials that need to kill enzymes and protect glycosides;besides,the cost is relatively high and the drying time is long.

Numerical Modelling of Drying Induced Cracks in Wood Discs Using the Extended Finite Element Method

Drying crack is a common phenomenon occurring during moisture discharge from wood,reducing efficient wood utilization.Drying crack is primarily caused by drying stress,and the reasonable methods for determining drying stress are sparse.In this study,the initiation and propagation of cracks during wood discs drying were simulated using the extended finite element method(XFEM).The distribution of drying stress and displacement was analyzed at different crack conditions based on the simulation results.This study aimed to solve the problem of the limitation of drying stress testing methods and provide a new idea for the study of wood drying stress.The numerical simulation results are found in good agreement with the experimental results,thus corroborating the feasibility of XFEM in modeling drying crack of wood discs.The stress concentration was observed at the crack tip region,while a minor stress was presented in the region of crack passing through,indicating that the crack formation process was also a process of releasing drying stress.Further,more energy was required to form double cracks in comparison with the single crack mode.

A Comparative Study of Different Drying Processes for a Deformable Saturated Porous Medium

Drying of a deformable saturated porous medium based on convective tempering is a novel method that can enhance energy efficiency and the quality of the dried product itself.In this experimental investigation,the performances of this specific technique are compared with those of a standard stationary drying process in terms of deformation,drying kinetics,moisture redistribution,and energy consumption.In particular,the response of a deformable saturated porous medium(Kaolin)is considered.The results are critically discussed pointing out advantages and drawbacks.

Hydraulic and volume change behaviors of compacted highly expansive soil under cyclic wetting and drying

The wide engineered application of compacted expansive soils necessitates understanding their behavior under field conditions.The results of this study demonstrate how seasonal climatic variation and stress and boundary conditions individually or collectively influence the hydraulic and volume change behavior of compacted highly expansive soils.The cyclic wetting and drying(CWD)process was applied for two boundary conditions,i.e.constant stress(CS)and constant volume(CV),and for a wide range of axial stress states.The adopted CWD process affected the hydraulic and volume change behaviors of expansive soils,with the first cycle of wetting and drying being the most effective.The CWD process under CS conditions resulted in shrinkage accumulation and reduction in saturated hydraulic conductivity(k sat).On the other hand,CWD under CV conditions caused a reduction of swell pressure while has almost no impact on k sat.An elastic response to CWD was achieved after the third cycle for saturated hydraulic conductivity(k sat),the third to fourth cycle for the volume change potential under the CV conditions,and the fourth to fifth cycle for the volume change potential under the CS conditions.Finally,both swell pressure(s s)and saturated hydraulic conductivity(k sat)are not fundamental parameters of the expansive soil but rather depend on stress,boundary and wetting conditions.

Investigation on microstructure evolution of clayey soils: A review focusing on wetting/drying process

Variability in moisture content is a common condition in natural soils.It influences soil properties significantly.A comprehensive understanding of the evolution of soil microstructure in wetting/drying process is of great significance for interpretation of soil macro hydro-mechanical behavior.In this review paper,methods that are commonly used to study soil microstructure are summarized.Among them are scanning electron microscope(SEM),environmental SEM(ESEM),mercury intrusion porosimetry(MIP)and computed tomography(CT)technology.Moreover,progress in research on the soil microstructure evolution during drying,wetting and wetting/drying cycles is summarized based on reviews of a large body of research papers published in the past several decades.Soils compacted on the wet side of op-timum water content generally have a matrix-type structure with a monomodal pore size distribution(PSD),whereas soils compacted on the dry side of optimum water content display an aggregate structure that exhibits bimodal PSD.During drying,decrease in soil volume is mainly caused by the shrinkage of inter-aggregate pores.During wetting,both the intra-and inter-aggregate pores increase gradually in number and sizes.Changes in the characteristics of the soil pore structure significantly depend on stress state as the soil is subjected to wetting.During wetting/drying cycles,soil structural change is not completely reversible,and the generated cumulative swelling/shrinkage deformation mainly derives from macro-pores.Furthermore,based on this analysis and identified research needs,some important areas of research focus are proposed for future work.These areas include innovative methods of sample preparation,new observation techniques,fast quantitative analysis of soil structure,integration of microstructural parameters into macro-mechanical models,and soil microstructure evolution charac-teristics under multi-field coupled conditions.

Modeling and simulation of solvent behavior and temperature distribution within long stick propellants with large web thickness undergoing drying

Drying is a complicated physical process which involves simultaneous heat and mass transfer in the removal of solvents inside propellants.Inappropriate drying techniques may result in the formation of a hard skin layer near the surface to block the free access of most solvent through for long stick propellants with large web thickness,which lead to lower drying efficiency and worse drying quality.This study aims to gain a comprehensive understanding of drying process and clarify the mechanism of the blocked layer near the propellant surface.A new three-dimensional coupled heat and mass transfer(3D-CHMT)model was successfully developed under transient conditions.The drying experiment results show that the 3DCHMT model could be applied to describe the drying process well since the relative error of the content of solvent between simulation and experiment values is only 5.5%.The solvent behavior simulation demonstrates that the mass transfer process can be divided into super-fast(SF)and subsequent minorfast(MF)stages,and the SF stage is vital to the prevention of the blocked layer against the free access for solvent molecules inside propellant grains.The effective solvent diffusion coefficient(Deff)of the propellant surface initially increases from 3.4×10^(-6)to 5.3×10^(-6)m^(2)/s as the temperature increases,and then decreases to 4.1×10^(-8)m^(2)/s at 60-100 min.The value of Deffof surface between 0-1.4 mm has a unique trend of change compared with other regions,and it is much lower than that of the internal at100 min under simulation conditions.Meanwhile,the temperature of the propellant surface increases rapidly at the SF stage(0-100 min)and then very slowly thereafter.Both the evolution of Deffand temperature distribution demonstrate that the blocked layer near the propellant surface has been formed in the time period of approximately 0-100 min and its thickness is about 1.4 mm.To mitigate the formation of blocked layer and improve its drying quality of finial propellant products effectively,it should be initially dried at lower drying temperature(30-40℃)in 0-100 min and then dried at higher drying temperature(50-60℃)to reduce drying time for later drying process in double base gun propellants.The present results can provide theoretical guidance for drying process and optimization of drying parameters for long stick propellants with large web thickness.

Diversity of Arbuscular Mycorrhizal Fungi Associated with Six Rice Cultivars in Italian Agricultural Ecosystem Managed with Alternate Wetting and Drying

Alternate wetting and drying(AWD)system,in which water has been reduced by approximately 35%with an increased occurrence of beneficial arbuscular mycorrhizal(AM)symbiosis and no negative impact on rice yield,was proposed to utilize water and nutrients more sustainable.In this study,we selected six rice cultivars(Centauro,Loto,Selenio,Vialone nano,JSendra and Puntal)grown under AWD conditions,and investigated their responsiveness to AM colonization and how they select diverse AM taxa.In order to investigate root-associated AM fungus communities,molecular cloning-Sanger sequencing on small subunit rDNA data were obtained from five out of the six rice cultivars and compared with Next Generation Sequencing(NGS)data,which were previously obtained in Vialone nano.The results showed that all the cultivars were responsive to AM colonization with the development of AM symbiotic structures,even if with differences in the colonization and arbuscule abundance in the root systems.We identified 16 virtual taxa(VT)in the soil compartment and 7 VT in the root apparatus.We emphasized that the NGS analysis gives additional value to the results thanks to a more in-depth reading of the less represented AM fungus taxa.

Drying kinetics of soy protein isolate-corn starch film during preparation and its moisture adsorption characteristics during storage

To better understand the mass transfer process of moisture in the soy protein isolate-corn starch(SPI-CS)films during preparation and storage process,the drying kinetics model of SPI-CS films with different formation conditions during the drying process and the moisture adsorption characteristics of the SPI-CS films under different humidity conditions were investigated.Within the range of experimental conditions,the moisture migration rule in the SPI-CS films during the drying preparation was combined with the Page model which was expressed as MR=exp(-kt^(n)).It was found that the adsorption equilibrium needed shorter time(about 3 h)when the SPI-CS films existed in the environment with lower humidity(RH<54%).Additionally,the secondorder adsorption kinetic equation was successful to describe the moisture adsorption characteristic of the SPICS films during storage under different humidity conditions.