Experimental Study of Heat Transfer in an Insulated Local Heated from Below and Comparison with Simulation by Lattice Boltzmann Method

In this paper,experimental and numerical studies of heat transfer in a test local of side H=0.8 m heated from below are presented and compared.All the walls,the rest of the floor and the ceiling are made from plywood and polystyrene in sandwich form(3 mmplywood-3 cm polystyrene-3 mmplywood)just on one of the vertical walls contained a glazed door(2 H/3×0.15 m).This local is heated during two heating cycles by a square plate of iron the width L=0.6 H,which represents the heat source,its temperature T_(h) is controlled.The plate is heated for two cycles by an adjustable set-point heat source placed just down the center of it.For each cycle,the heat source is switched“on”for 6 h and switched“off”for 6 h.The outdoor air temperature is kept constant at a low temperature T_(c)<T_(h).All measurements are carried out with k-type thermocouples and with flux meters.Results will be qualitatively presented for two cycles of heating in terms of temperatures and heat flux densitiesϕfor various positions of the test local.The temperature evolution of the center and the profile of the temperature along the vertical centerline are compared by two dimensions simulation using the lattice Boltzmann method.The comparison shows a good agreement with a difference that does not exceed±1℃.

Theoretical and Experimental Study on the Performance of Hermetic Diaphragm Squeeze Film Dampers for Gas-Lubricated Bearings

Low damping characteristics have always been a key sticking points in the development of gas bearings.The application of squeeze film dampers can significantly improve the damping performance of gas lubricated bearings.This paper proposed a novel hermetic diaphragm squeeze film damper(HDSFD)for oil-free turbomachinery supported by gas lubricated bearings.Several types of HDSFDs with symmetrical structure were proposed for good damping performance.By considering the compressibility of the damper fluid,based on hydraulic fluid mechanics theory,a dynamic model of HDSFDs under medium is proposed,which successfully reflects the frequency dependence of force coefficients.Based on the dynamic model,the effects of damper fluid viscosity,bulk modulus of damper fluid,thickness of damper fluid film and plunger thickness on the dynamic stiffness and damping of HDSFDs were analyzed.An experimental test rig was assembled and series of experimental studies on HDSFDs were conducted.The damper fluid transverse flow is added to the existing HDSFD concept,which aims to make the dynamic force coefficients independent of frequency.Although the force coefficient is still frequency dependent,the damping coefficient at high frequency excitation with damper fluid supply twice as that without damper fluid supply.The results serve as a benchmark for the calibration of analytical tools under development.

Experimental study on box shape steel reinforced concrete beam

Experimental study on the fundamental behavior of box shape steel reinforced concrete （SRC） beams was conducted. Seven 1 ： 3 scale model SRC beams were tested to failure. The experimental results indicate that the flexural strength increases with the increase of the ratio of flexural reinforcement and the thickness of flange of the shape steel; the shear strength increases with the increase in the thickness of the web of the shape steel. Concrete filled in the box shape steel can prevent the early failure of specimens due to the buckling of the box shape steel, and increase the ultimate load. Measures should be made to strengthen the connection and co-work between the shape steel and the concrete. Formulae for flexural and shear strength of the composite beams are proposed, and the calculated results are in good agreement with the experimental results. In general, the box shape SRC beam is a kind of ductile member, and it is suitable for extensive engineering application.

Simulation Analysis and Experimental Study of Defect Detection Underwater by ACFM Probe

This article studies the application of the alternating current field measurement （ACFM） method in defect detection for underwater structures. Numerical model of the ACFM system is built for structure surface defect detection in seawater environment. Finite element simulation is performed to investigate rules and characteristics of the electromagnetic signal distribution in the defected area. In respect of the simulation results, underwater artificial crack detection experiments are designed and conducted for the ACFM system. The experiment results show that the ACFM system can detect cracks in underwater structures and the detection accuracy is higher than 85%. This can meet the engineering requirement of underwater structure defect detection. The results in this article can be applied to establish technical foundation for the optimization and development of ACFM based underwater structure defects detection system.

A field experimental study of lignin sand stabilizing material(LSSM) extracted from spent-liquor of straw pulping paper mills

A new technique was introduced for sand stabilization and re-vegetation by use of lignin sand stabilizing material(LSSM). LSSM is a reconstructed organic compound with lignin as the most dominant component from the extracts of black-liquor issued by straw pulp paper mills. Unlike the polyvinyl acetate or foamed asphalt commonly used for dune stabilization, the new material is plant-friendly and can be used with virescence actions simultaneously. The field experimental study was conducted since 2001 in China's Northwest Ningxia Hui Autonomous Region and has been proved that LSSM is effective in stabilizing the fugitive dunes, making the arenaceous plants survive and the bare dune vegetative. The advisable solution concentration is 2% and the optimal field spraying quantity is 2 5 L/m^2 The soil nutrients of the stabilized and greened dune, such as organic matter, available phosphorous and total nitrogen are all increased compared with the control treatment, which is certainly helpful to the growth of arenaceous plants. The technique is worthwhile to be popularized because it is provided not only a new method for desertification control but also an outlet for cleaning contaminants issued from the straw paper mills.

Experimental Study on Characteristics of NiMnGa Magnetically Controlled Shape Memory Alloy

The static and dynamic magnetic controlling characteristics of NiMnGa magnetically controlled shape memory alloy （MSMA） were experimentally studied. The results show that the characteristics of induced strain with respect to the magnetic field are nonlinear with saturation nature, and dependent on the temperature as well as the load applied to the MSMA. The magnetic shape memory effect can be observed only in complete martensite phase at room temperature. The magnetic permeability of MSMA is not constant and reduces with the increment of magnetic field. The relative saturation magnetic permeability of MSMA is about 1.5.

Experimental Study on the Aerodynamic Performance of Swept-Curved Blade

Compared with a straight blade, a unique compressor blade integratedforward-swept and positive-curved stacking line is studied experimentally. Aerodynamic parameters ofthe two cascades are measured by a five-hole probe at different positions and ink trace flowvisualization is conducted on blade surfaces. The result shows that the swept-curved cascade haslower endwall loss and higher midspan loss as compared with the straight cascade. However, lowerloss is accompanied with lower diffusion factor. Opposite 'C' shape static pressure distribution isestablished on the suction surface of the swept-curved blade, which is helpful for avoiding theaccumulation of low energy fluid in the endwall corner region. Anyhow the studies support theconclusion that the swept-curved blade conduces to not only the reduction of overall loss but alsothe improvement of stable operation in the endwall corner region.

Design and Experimental Study of an 80C196KC-Based SRD System Controller

Aim To design and experimentally study an 80C196KC-based SRD (switched re- luctance motor drive drive sytem) controller,Methods with the guidelines of the digitized SRD system controller,the circuit design and software programming were completed,and a relevantexperimental system was PUT forward to test the newly designed controller.Result The experi-mental study showed that the newlydesigned controller had good speed-adjusting characteristicfor a switched reluctance motor ,its stable error was less than 5% and its full-load startingtime was shorter than 1.8s .Conclusion The new controller has reasonable circuit design and suitable controlling algorithm,and it is a feasible SRD system controller design scheme.

Experimental study of destruction to porcine spleen in vivo by microwave ablation

AIM: To discuss the safety, feasibility and regularity of destruction to porcine spleen in vivo with congestion and tumescence by microwave ablation (MWA). METHODS: Ligation of the splenic vein was used to induce congestion and tumescence in vivo in five porcine spleens, and microwave ablation was performed 2-4 h later. A total of 56 ablation points were ablated and the ablation powers were 30-100 W. The ablation time (1, 2, 3, 4, 5, 6, 7, 8, 9 and 10 min) was performed at a power of 60 W. After ablation, the ablation size was measured in pigs A, C, D and E and spleen resection. In pig B, the ablation size was measuredand 2 ablation points were sent for pathology analysis and all tissues were sutured following ablation. Pig B was killed 1 wk later and the ablation points were sent for pathology analysis. Bleeding, tissue carbonization surrounding electrodes, and pathological changes were observed, and the effect on destruction volume relative to different ablation powers, times and positions was analyzed. RESULTS: The incidence of bleeding (only small amounts, < 20 mL) in the course of ablation was 5.4% (3/56) and was attributed to tissue carbonization surrounding electrodes, which also exhibited an incidence of 5.4% (3/56). The destruction volume was influenced by different ablation powers, times and points. It showed that the ablation lesion size increased with increased ablation time, from 1 to 10 min, when the ablation power was 60 W. Also, the ablation lesion size increased with the increase of ablation power, ranging from 30 to 100 W when the ablation time was set to 3 min. A direct correlation was seen between the destruction volume and ablation time by the power of 60 W (r = 0.97542, P < 0.0001, and also between the destruction volume and ablation powers at an ablation time of 3 min (r = 0.98258, P < 0.0001). The destruction volume of zone Ⅱ (the extra-2/3 part of the spleen, relative to the fi rst or second class vascular branches), which was near the hilum of the spleen, was noteably larger than the destruction volume of zoneⅠ(the intra-1/3 part of the spleen) which was distal from the hilum of the spleen (P = 0.0015). Pathological changes of ablation occurring immediately and 1 wk after MWA showed large areas of coagulation. Immediately following ablation, intact spleen tissues were observed in the areas of coagulation necrosis, mainly around arterioles, and there were no obvious signs of hydropsia and inflammation, while 1 wk following the ablation, the coagulation necrosis was well distributed and complete, as many nuclear fragmentations were detected, and there were obvious signs of hydropsia and inflammation.CONCLUSION: In vivo treatment of congestion and tumescence in the spleen using microwave ablation of water-cooled antenna is a safe and feasible method that is minimally invasive.

Experimental Study on Bubble Pulse Features Under the Combined Action of Horizontal and Vertical Walls

The pulse features of a bubble have a close connection with the boundary condition. When a bubble moves near a rigid wall, it will be attracted by the Bjerknes force of the wall, and a jet pointing at the wall will be generated. In real application, the bubble may move under the combined action of walls in different directions when it forms at the corner of a pipe or at the bottom of a dam. The motion of the bubble shows complex and nonlinear characteristics under these conditions. In order to investigate the bubble pulse features near complex walls, a horizontal wall and a vertical wall are put into the experimental water tank synchronously, and an electric circuit with 200 voltages is designed to generate discharge bubbles, and then experimental study on the bubble pulse features under the combined action of horizontal and vertical walls is carried out. The influences of the combined action of two walls on the bubble shape, pulse period, moving trace and inside jet are obtained by changing the distances from bubble center to the two walls. It aims at providing references for the relevant theoretical and numerical research.

Experimental study ofcasing wear under impact-sliding conditions

Theoretical analysis and field monitoring show that lateral vibration has very important effect on casing wear in deep & ultra-deep well drilling. The wear mechanism of casing under impact-sliding work conditions has been investigated and many experiments have been completed with a newly developed full-scale casing wear test machine. Test results present that adhesion wear, contact fatigue, and grinding abrasion are the main wear mechanisms under impact-sliding test conditions. The friction coefficient and linear wear rate of the casing rise obviously with an increase in impact load. And the larger the impact load, the rougher the worn surface of the casing. The linear wear rate decreased slightly but the average friction coefficient increased slightly with an increase in impact frequency under an impact load of 2,500 N. Both the linear wear rate of the casing and the average friction coefficient increased substantially with an increase in impact frequency under an impact load of 4,000 N. Under lower impact load conditions, grinding abrasion and contact fatigue are the main mechanisms of casing wear; under higher impact load conditions, adhesion wear and contact fatigue are the main mechanisms of casing wear.

Experimental Study of Multi-slice Spiral CT Perfusion Imaging in VX_ 2 Soft-tissue Tumor of Rabbits

An experimental animal model of malignant soft-tissue tumor was established to investigate the applied value of multi-slice spiral CT perfusion imaging preliminarily. Ten New Zealand white rabbits which were implanted with VX2 tumor in either proximal thigh were subjected to CT plain scan and perfusion scan two weeks later respectively, then the original perfusion images were transmitted to AW4.0 Workstation. The functional maps and perfusion parameters including blood flow （BF）, blood volume （BV）, mean transit time （MTT） and permeability surface （PS） were computed and analyzed. All the values of BF, BV and PS in VX2 soft-tissue tumors were obviously higher while the MTT-values were lower than those in the normal muscular tissues significantly. It was suggested that multi-slice spiral CT perfusion imaging is an accurate, convenient and relatively safe functional imaging technique, and can give a quantitative assessment to angiogenesis and blood perfusion of soft-tissue tumors.

Experimental study on stable isotopic fractionation of evaporating water under varying temperature

The variation of stable isotope ratios in natural waters provides valuable information that can be used to trace water movement. Evaporation plays a crucial role in determining the variation of stable isotopes. In this paper, several evaporation experiments were conducted in order to study the stable isotopic fractionation mechanism of water and analyze the influence of different temperatures on evaporation fractionation. Three group experiments of water evaporation under different temperatures and initial isotopic values were carried out. The results show that fractionation factors of hydrogen and oxygen may increase with temperature, and the average enrichment degree of hydrogen isotope D is 3.432 times that of oxygen isotope 18O. The results also show that the isotopic composition of the initial water has little influence on water evaporation fractionation, which is mainly affected by the state variables in the evaporation process, such as temperature. This research provides experimental data for further understanding the evaporation fractionation mechanism.

An Experimental Study on the Effect of the Side Hull Symmetry on the Resistance Performance of a Wave‑Piercing Trimaran

This paper presented the results of an experimental investigation into the resistance performance of a wave-piercing trimaran with three alternative side hull forms,including asymmetric inboard,asymmetric outboard,and symmetric at various stagger/separation positions.Model tests were carried out at the National Iranian Marine Laboratory(NIMALA)towing tank using a scale model of a trimaran at the Froude numbers from 0.225 to 0.60.Results showed that by moving the side hulls to the forward of the main hull transom,the total resistance coefficient of trimaran decreased.Findings,furthermore,demonstrated that the symmetry shape of the side hull had the best performance on total resistance among three side hull forms.Results of this study are useful for selecting the side hull configuration from the resistance viewpoint.

Experimental study on surface arc plasma actuation-based hypersonic boundary layer transition flow control

Effective control of hypersonic transition is essential.In order to avoid affecting the structural proflle of the aircraft,as well as reducing power consumption and electromagnetic interference,a low-frequency surface arc plasma disturbance experiment to promote hypersonic transition was carried out in theΦ0.25 m double-throat Ludwieg tube wind tunnel at Huazhong University of Science and Technology.Contacting printed circuit board sensors and non-contact focused laser differential interferometry testing technology were used in combination.Experimental results showed that the low-frequency surface arc plasma actuation had obvious stimulation effects on the second-mode unstable wave and could promote boundary layer transition by changing the spectral characteristics of the second-mode unstable wave.At the same time,the plasma actuation could promote energy exchange between the second-mode unstable wave and other unstable waves.Finally,the corresponding control mechanism is discussed.

AN EXPERIMENTAL STUDY OF SHEET EROSION IN GRANITIC REGION OF WUHUA COUNTY,GUANGDONG PROVINCE

The relationships between rainfall, runoff and erosion in South China granitic weathering red soil region were studied by using data collected from 7 experimental plots in Wuhua County, Guangdong Province. Results showed that when rainfall is less than 50 mm, small volumes of runoff were produced. Rainfall intensity might be the main factor in controlling runoff. When rainfall exceeds 50 mm, because of its large volume and high intensity, runoff and the produced amount of erosion increased with raimfall quickly. Analysis of the relationship bebeen runoff and erosion suggsted that runoff of 30 mm (corresponding to about 50 mm rainfall might be taken as a threshold at which wter on land surface was sufficient to start the larg amount of soil particles. Vegtation cover is very effective in protection soil from being eroded. When vegetation coverag increases from 0 to 80 percent,runoff and soil loss decrease from 179.34mm/a to 126.36mm/a and 6262.15T/a km2 to 368.02 T/a km2, respectively.

An Experimental Study of Bulge-Forming Polycarbonate (PC)Semisphere Shell Parts

In this paper, a new bulge-forming technology is described to manufacture a polycarbonate semisphere shell. Some experiments have been done, and the experimental results show that this technique is feasible to form polycarbonate part. But the wall thickness distribution of the bulged specimen by this method is not so even.

Clinical and Experimental Study on Effect of Garlicin in Treating Angina Pectorls

Objective: To observe the effect and mechanism of Garlicin in treating coronary heart disease (CHD) with angina pectoris. Methods: Clinical study: 55 patients were selected and randomized into the Garlicin group and the nitroglycerin group. To Garlicin group, 60 mg of Garlicin was given by adding in 5% glucose solution for intravenous dripping once per day, the therapeutic course

Experimental Study on Uniaxial and Multiaxial Strain CyclicCharacteristics and Ratcheting of 316L Stainless Steel

An experimental study was carried out on the strain cyclic characteristics and ratcheting of 316L stainless steel subjected to uniaxial and multiaxial cyclic loading. The strain cyclic characteristics were researched under the strain-controlled uniaxial tension-compression and multiaxial circular paths of loading. The ratcheting tests were conducted for the stress-controlled uniaxial tension-compression and multiaxial circular, rhombic and linear paths of loading with different mean stresses, stress amplitudes and histories. The experiment results show that 316L stainless steel features the cyclic hardening, and its strain cyclic characteristics depend on the strain amplitude and its history apparently. The ratcheting of 316L stainless steel depends greatly on the Values of mean stress, stress amplitude and their histories. In the meantime, the shape of load path and its history also apparently influence the ratcheting.

An Experimental Study on Atmospheric Pressure Glow Discharge in Different Gases

Usually, the electrical breakdown of dielectric barrier discharge (DBD) at atmo-spheric pressure leads to a filamentary non-homogeneous discharge. However, it is also possible to obtain a diffuse DBD in homogeneous form, called atmospheric pressure glow discharge (APGD). We obtained a uniform APGD in helium and in the mixture of argon with alcohol, and studied the electrical characteristics of helium APGD. It is found that the relationship between discharge current and source frequency is different depending on the difference in gas gap when the applied voltage is kept constant. The discharge current shows an increasing trend with the increased frequency when gas gap is 0.8 cm, but the discharge current tends to decrease with the increased frequency when the gas gap increases. The discharge current always increases with the increased applied voltage when the source frequency is kept constant. We also observed a glow-like discharge in nitrogen at atmospheric pressure.