Origin of nucleation and growth of extension twins in grains unsuitably oriented for twinning during deformation of Mg-1%Al

A large number of anomalous extension twins,with low or even negative twinning Schmid factors,were found to nucleate and grow in a strongly textured Mg-1Al alloy during tensile deformation along the extruded direction.The deformation mechanisms responsible for this behaviour were investigated through in-situ electron back-scattered diffraction,grain reference orientation deviation,and slip trace-modified lattice rotation.It was found that anomalous extension twins nucleated mainly at the onset of plastic deformation at or near grain boundary triple junctions.They were associated with the severe strain incompatibility between neighbour grains as a result from the differentbasal slip-induced lattice rotations.Moreover,the anomalous twins were able to grow with the applied strain due to the continuous activation ofbasal slip in different neighbour grains,which enhanced the strain incompatibility.These results reveal the complexity of the deformation mechanisms in Mg alloys at the local level when deformed along hard orientations.

Diagnostic Study of an Extreme Explosive Cyclone over the Kuroshio/Kuroshio Extension Region

Explosive cyclones(ECs)occur frequently over the Kuroshio/Kuroshio Extension region.The most rapidly intensified EC over the Kuroshio/Kuroshio Extension region during the 42 years(1979-2020)of cold seasons(October-April)was studied to reveal the variations of the key factors at different explosive-developing stages.This EC had weak low-level baroclinicity,mid-level cyclonic-vorticity advection,and strong low-level water vapor convergence at the initial explosive-developing stage.The low-level baroclinicity and mid-level cyclonic-vorticity advection increased substantially during the maximum-deepening-rate stage.The diagnostic analyses using the Zwack-Okossi equation showed that diabatic heating was the main contributor to the initial rapid intensification of this EC.The cyclonic-vorticity advection and warm-air advection enhanced rapidly in the middle and upper troposphere and contributed to the maximum rapid intensification,whereas the diabatic heating weakened slightly in the mid-low troposphere.The relative contribution of the diabatic heating decreased from the initial explosive-developing stage to the maximum-deepening-rate stage due to the enhancement of other factors(the cyclonic-vorticity advection and warm-air advection).Furthermore,the physical factors contributing to this EC varied with the explosive-developing stage.The non-key factors at the initial explosive-developing stage need attention to forecast the rapid intensification.

The Origin of Mesozoic A-type Granitoids,Fujian Province,Southeast China:Insights from Geochronology,Mineralogy and Geochemistry

The magma sources,origins and precise forming ages of the miarolite from Qishan and Kuiqi intrusions are still uncertain.New results reveal that,miarolites from the Qishan and Kuiqi intrusions yield crystallization ages of~101 and~98 Ma,and they have a high formation temperature(~910℃)and low oxygen fugacity value,indicating crystallization condition at low pressure in the upper crust with temperature of 678℃.The Qishan and Kuiqi miarolites are characterized by enrichment in SiO_(2) and high-K alkali,depletion in Ca and Mg,and belong to the high-K weak peraluminous rock series.The samples are enriched in HFSEs(i.e.,Ta,Zr and Hf)and LILEs(i.e.,Ba,P and Sr),depleted in Ba and Sr with the negative anomaly of Eu.In the primitive mantle normalized trace element spider diagram,the samples show a right-inclined‘seagull-type’pattern,combined the ratios of(La/Yb)_(N),10000×Al/Ga,Rb/Nb and Nb/Ta etc.,they were proved to be alkaline A-type granite.Combined the characterize of the trace elements,they were derived from clay-rich source accompanied pelite melting,and subjected to K-feldspar crystallization fractional.The values of ε_(Hf)(t)and tDM2 are distributed in the range of-2.8 to 3.3 with~1.2 Ga,and-6.0 to 4.0 with~1.2 Ga,revealing that they were generated from the Mesoproterozoic Cathaysia basement rocks.The comprehensive research reveals the Kuiqi and Qishan intrusions derived from crust-mantle mixing and partial melting of the crust,respectively,resulting from lithospheric extension generated by the Paleo-Pacific Plate subducted into the European-Asian Plate.

Phanerozoic Tectonic Evolution,Metallogenesis and Formation of Mineral Systems in China

The continental Asia is mainly composed of three major tectonic regimes,the Tethys,Paleo Asian Ocean,and West Pacific.It underwent multi-stage plate convergences,ocean-continent transformations,and subductions,collisions and/or collages,and post collisional(orogenic)extensions in Phanerozoic.Tectonic evolution of the Asia brings up a unique fault system and tectonic geomorphological features in the China's Mainland.Also,it provides a geodynamic background for the formation and evolution of metallogeneses and mineral systems,resulting in nonuniform distribution of tectono-metallogenic systems and metallogenic belts.The spatiotemporal distribution of mineral deposits in China and adjacent areas exhibits periodic variation under controlling of the full life Wilson cycle and tectonic evolution,forming the plate convergence-related mineral system in East Asia.Porphyry Cu deposits are mainly related to compressional systems in Paleozoic and early Mesozoic,and more closely related to post-collision extensional settings in late Mesozoic and Cenozoic.Orogenic Au deposits mainly formed in post-orogeny extensional setting.Alkaline rock related rare earth element deposits formed mainly at margins of the North China and Yangtze cratons.Granite-pegmatite Li and other rare metal deposits formed mainly in early Mesozoic,related to Indosinian post-orogeny extension.Tectono-metallogenic systems provide important basis for the prospecting of mineral resources.

GUIDE FOR AUTHORS

Articlen ■Article types Articles commonly fall into one of three main categories:Fulllength articles,Review articles and Short communications.Full-length articles are original,unpublished primary research.Extensions of work that has been published previously in short form such as a Communication are usually acceptable.

A mechanically coupled MEMS filter with high-Q width extensional mode resonators

This work presents a novel radio frequency(RF)narrowband Si micro-electro-mechanical systems(MEMS)filter based on capacitively transduced slotted width extensional mode(WEM)resonators.The flexibility of the plate leads to multiple modes near the target frequency.The high Q-factor resonators of around 100000 enable narrow bandwidth filters with small size and simplified design.The 1-wavelength and 2-wavelength WEMs were first developed as a pair of coupled modes to form a passband.To reduce bandwidth,two plates are coupled with aλ-length coupling beam.The 79.69 MHz coupled plate filter(CPF)achieved a narrow bandwidth of 8.8 kHz,corresponding to a tiny 0.011%.The CPF exhibits an impressive 34.84 dB stopband rejection and 7.82 dB insertion loss with near-zero passband ripple.In summary,the RF MEMS filter presented in this work shows promising potential for application in RF transceiver front-ends.

GUIDE FOR AUTHORS

Article Article types Articles commonly fall into one of three main categories:Full-length articles,Review articles and Short communications.Full-length articles are original,unpublished primary research.Extensions of work that has been published previously in short form such as a Communication are usually acceptable.

GUIDE FOR AUTHORS

Article Article types Articles commonly fall into one of three main categories:Fulllength articles,Review articles and Short communications.Full-length articles are original,unpublished primary research.Extensions of work that has been published previously in short form such as a Communication are usually acceptable.Short communications must contain original and highly significant work whose high novelty warrants rapid publication.Review articles may be an authoritative overview of a field,a comprehensive literature reviews,or tutorial-style reference materials.Reviews are usually invited by the editor,but a topic may be proposed by an author via the editorial office.

Early Devonian Post-collisional Granitic Magmatism in the North Qilian Orogenic Belt,Western China:Insights into Lithospheric Delamination and Orogenic Collapse

Post-collisional magmatism contains important clues for understanding the reworking and growth of continental crust,as well as lithospheric delamination and orogenic collapse.Early Devonian magmatism has been identified in the North Qilian Orogenic Belt(NQOB).This paper reports an integrated study of petrology,whole-rock geochemistry,Sm-Nd isotope and zircon U-Pb dating,as well as Lu-Hf isotopic data,for two Early Devonian intrusive plutons.The Yongchang and Chijin granites yield zircon U-Pb ages of 394-407 Ma and 414 Ma,respectively.Both of them are characterized by weakly peraluminous to metaluminous without typical aluminium-rich minerals,LREE-enriched patterns with negative Eu anomalies and a negative correlation between P_(2)O_(5) and SiO_(2) contents,consistent with geochemical features of I-type granitoids.Zircons from the studied granites display negative to weak positive ε_(Hf)(t)values(−5.7 to 2.1),which agree well with those of negative ε_(Nd)(t)values(−6.4 to−2.9)for the whole-rock samples,indicating that they were derived from the partial melting of Mesoproterozoic crust.Furthermore,low Sr/Y ratios(1.13-21.28)and high zircon saturation temperatures(745℃ to 839℃,with the majority being>800℃)demonstrated a relatively shallow depth level below the garnet stability field and an additional heat source.Taken together,the Early Devonian granitic magmatism could have been produced by the partial melting of ancient crustal materials heated by mantle-derived magmas at high-temperature and low-pressure conditions during postcollisional extensional collapse.The data obtained in this study,when viewed in conjunction with previous studies,provides more information about the tectonic processes that followed the closure of the North Qilian Ocean.The tectonic transition from continental collision to post-collisional delamination could be constrained to~430 Ma,which is provided by the sudden decrease of Sr/Y and La/Yb ratios and an increase in zircon ε_(Hf)(t)values for granitoids.A two-stage tectonic evolution model from continental collision to post-collisional extensional collapse for the NQOB includes(a)continental collision and crustal thickening during ca.455-430 Ma,characterized by granulite-facies metamorphism and widespread low-Mg adakitic magmatism;(b)post-collisional delamination of thickened continental crust and extensional collapse of orogen during ca.430-390 Ma,provided by coeval high-Mg adakitic magmatism,A-type granites and I-type granitoids with low Sr-Y ratios.

Unveiling the rolling texture variations ofα-Mg phases in a dual-phase Mg-Li alloy

LZ91 Mg-Li alloy plates with three types of initial texture were rolled by 70%reduction at both room temperature and 200℃to explore the rolling texture formation ofα-Mg phase.The results showed that the rolling texture is largely affected by the initial texture.All the samples exhibited two main texture components as RD-split double peaks texture and TD-split double peaks texture after large strain rolling.The intensity of the two texture components was strongly influenced by the initial orientation and rolling temperature.Extension twinning altered the large-split non-basal orientation to a near basal one at low rolling strain.The basal orientation induced by twinning is unstable,which finally transmitted to the RD-split texture.The strong TD-split texture formed due to slip-induced orientation transition from its initial orientation.The competition between prismatic and basal slip determined the intensity and tilt angle of the TD-split texture.By increasing the rolling temperature,the TD-split texture component was enhanced in all three samples.Limitation of extension twinning behavior and the promotion of prismatic slip at elevated temperature are the main reasons for the difference in hot and cold rolling texture.

A Novel Three-stage Tectonic Model for Mississippi Valleytype Zn-Pb Deposits in Orogenic Fold-and-Thrust Belts

Mississippi Valley-type(MVT) Zn-Pb deposits predominantly form within both orogenic forelands and fold-andthrust belts, yet the mineralization process within the latter tectonic setting remains inadequately understood. This study, through a comprehensive review of MVT deposits across global fold-and-thrust belts, introduces a novel model elucidating the mineralization process in the context of tectonic belt evolution. It is demonstrated that during the stage Ⅰ, regional compression is introduced by early stages of plate convergence, causing the folding and thrusting and creating structural or lithological traps such as evaporite diapirs and unconformity-related carbonate dissolution-collapse structures. Thereafter, in stage Ⅱ, hydrocarbons begin to migrate and accumulate within these traps, where reduced sulfur is generated through thermochemical or bacterial sulfate reduction concurrent with or preceding Zn-Pb mineralization. In the subsequent stage Ⅲ, as plate convergence persists, the regional stress transitions from compression to transpression or extension. Under these conditions, steeply-dipping extensional faults are generated, facilitating the ascent of metalliferous brines into early-formed structural or lithological traps. Precipitation of Zn and Pb sulfides occurs through the mixing of Zn-Pb-transporting fluids with pre-existing reduced sulfur or by interaction with hydrocarbons.

Anisotropic FCGR behaviour in hot-rolled Mg-3Al-0.5Ce alloy

In this work,anisotropic fatigue crack growth rate(FCGR)behaviour in a hot-rolled Mg-3wt%Al-0.5wt%Ce alloy was investigated using compact tension(CT)specimens with notch(an)parallel to the rolling direction(RD)and transverse direction(TD).The FCGR tests were conducted at a constant load ratio(R=0.1)and maximum stress intensity factor(KMax=15.6 MPam)to investigate the crack closure effect.For both constant R and KMax conditions:(i)the load-displacement curves for every loading cycle were linear for anto RD and TD,indicating no crack closure;(ii)the FCGR was found to be lower for anRD than anTD over the entire stress intensity factor range(△K).The hot-rolled sample contained long-aligned Al11Ce3 intermetallic phase within grain boundaries that are elongated along RD.During the FCGR test,{10.12}10.11extension twins(ET)with lamellae∼||⊥and c-axis∼||to these elongated intermetallics along RD developed irrespective of the notch orientation.During the loading cycle,these intermetallics along RD generate back-stresses,reducing the in-plane tensile stress∼||and∼⊥to crack-tip to∼0 for anto RD and TD,respectively.Hence,lenticular ET∼||⊥and∼||,with c-axis∼||and∼⊥to crack path activates,leading to trans and inter lamellar crack for anto RD and TD,respectively,and anisotropic FCGR.Translamellar crack in anRD reduces the FCGR due to plastic energy dissipation as perceived by comparatively more geometrically necessary boundaries(GNBs).On the other hand,faster FCGR was obtained for anTD due to interlamellar cracking.Thus,the crack growth through the matrix-ET interfaces was favoured due to strain incompatibility.The Fractography for anRD shows smaller elongated grooves along crack propagation,which indicates crack arrest.However,larger elongated grooves for an||TD indicated easy crack propagation due to favourable interlamellar crack.

Surface crack evolution patterns in freeze-thaw damage of fissured rock bodies

To explore the effects of freeze‒thaw cycles on the mechanical properties and crack evolution of fissured sandstone,biaxial compression experiments were carried out on sandstone subjected to freeze‒thaw cycles to characterize the changes in the physical and mechanical properties of fissured sandstone caused by freeze‒thaw cycles.The crack evolution and crack change process on the surface of the fissured sandstone were recorded and analysed in detail via digital image technology(DIC).Numerical simulation was used to reveal the expansion process and damage mode of fine-scale cracks under the action of freeze‒thaw cycles,and the simulation results were compared and analysed with the experimental data to verify the reliability of the numerical model.The results show that the mass loss,porosity,peak stress and elastic modulus all increase with increasing number of freeze‒thaw cycles.With an increase in the number of freeze‒thaw cycles,a substantial change in displacement occurs around the prefabricated cracks,and a stress concentration appears at the crack tip.As new cracks continue to sprout at the tips of the prefabricated cracks until the microcracks gradually penetrate into the main cracks,the displacement cloud becomes obviously discontinuous,and the contours of the displacement field in the crack fracture damage area simply intersect with the prefabricated cracks to form an obvious fracture.The damage patterns of the fractured sandstone after freeze‒thaw cycles clearly differ,forming a symmetrical"L"-shaped damage pattern at zero freeze‒thaw cycles,a symmetrical"V"-shaped damage pattern at 10 freeze‒thaw cycles,and a"V"-shaped damage pattern at 20 freeze‒thaw cycles.After 20 freeze‒thaw cycles,a"V"-shaped destruction pattern and"L"-shaped destruction pattern are formed;after 30 freeze‒thaw cycles,an"N"-shaped destruction pattern is formed.This shows that the failure mode of fractured sandstone gradually becomes more complicated with an increasing number of freeze‒thaw cycles.The effects of freeze‒thaw cycles on the direction and rate of crack propagation are revealed through a temperature‒load coupled model,which provides an important reference for an in-depth understanding of the freeze‒thaw failure mechanisms of fractured rock masses.

Wellbore Cleaning Degree and Hydraulic Extension in Shale Oil Horizontal Wells

The efficient development and exploitation of shale oil depends on long-distance horizontal wells. As the degreeof cleaning of the wellbore plays a key role in these processes, in this study, this problem is investigated experimentallyby focusing on the dimensionless cuttings bed height. A method is proposed to calculate the horizontalwellhydraulic extension taking into account the influence of the wellbore cleaning degree on the wellborepressure distribution and assess the effect of a variety of factors such as the bottom hole pressure, the circulatingpressure drop, the drilling pump performance and the formation properties. The analysis shows that the hydraulicextension of horizontal wells decreases with an increase in the cuttings bed height, and the higher the displacementof drilling fluid, the faster the hydraulic extension declines. The annular pressure drop of the horizontalsection increases with the increase of the cuttings bed height, resulting in a higher bottom-hole pressure. Severalarguments are provided to guide the safe drilling of shale oil horizontal wells and overcome the limits of currenttechnological approaches.

Fish Gelatin-Based Film Containing Maillard Reaction Products:Properties and Its Use as Bag for Packing Chicken Skin Oil

Maillard reaction is a non-enzymatic browning reaction and its products(MRPs)have been proven to possess antioxidant properties.This research aimed to produce a fish gelatin-based packaging incorporated with MRPs to retard lipid oxidation in chicken skin oil(CSO)during storage at ambient temperature(28℃–30℃).MRPs produced from fish gelatin and fructose(1:1,90℃,pH 11)showed the highest antioxidant properties compared to those prepared under other conditions.Different glycerol/MRPs ratios(30:0,25:5,20:10,15:15,10:20,5:25,0:30)were incorporated into the film and resulting films were characterized.Glycerol/MRPs at 10:20 ratio was chosen to add into the film prior to bag preparation via heat sealing method.CSO packed in the bag was monitored for lipid hydrolysis and oxidation during 15 days of storage(30℃±0.5℃,RH 52%±5%).After 15 days,quality deterioration was lower in CSO packed in the prepared gelatin bag as evidenced by lower FFA,TBARS,and volatile compounds in comparison with CSO packed in LDPE bag.Fish gelatin film added with MRPs possessed an excellent water vapor barrier property(WV-BP).This finding indicated that MRPs could be used to substitute glycerol and simultaneously could serve as antioxidants for the developed active bag.The novel packaging can be a potential alternative packaging for retarding lipid oxidation of lipid or fatty foods.

Integrated design and control technology of liner completion and drilling for horizontal wells

Aiming at the problems of large load of rotation drive system,low efficiency of torque transmission and high cost for operation and maintenance of liner steering drilling system for the horizontal well,a new method of liner differential rotary drilling with double tubular strings in the horizontal well is proposed.The technical principle of this method is revealed,supporting tools such as the differential rotation transducer,composite rotary steering system and the hanger are designed,and technological process is optimized.A tool face control technique of steering drilling assembly is proposed and the calculation model of extension limit of liner differential rotary drilling with double tubular strings in horizontal well is established.These results show that the liner differential rotary drilling with double tubular strings is equipped with measurement while drilling(MWD)and positive displacement motor(PDM),and directional drilling of horizontal well is realized by adjusting rotary speed of drill pipe to control the tool face of PDM.Based on the engineering case of deep coalbed methane horizontal well in the eastern margin of Ordos Basin,the extension limit of horizontal drilling with double tubular strings is calculated.Compared with the conventional liner drilling method,the liner differential rotary drilling with double tubular strings increases the extension limit value of horizontal well significantly.The research findings provide useful reference for the integrated design and control of liner completion and drilling of horizontal wells.

Spatial-temporal distribution and geochemistry of highly evolved Mesozoic granites in Great Xing’an Range,NE China:Discriminant criteria and geological significance

Highly evolved granite is an important sign of the mature continent crust and closely associated with deposits of rare metals.In this work,the authors undertake systematically zircon U-Pb ages and whole rock elemental data for highly evolved granitic intrusions from the Great Xing’an Range(GXR),NE China,to elucidate their discriminant criteria,spatial-temporal distribution,differentiation and geodynamic mecha-nism.Geochemical data of these highly evolved granites suggest that high w(SiO_(2))(>70%)and differentiation index(DI>88)could be quantified indicators,while strong Eu depletion,high TE_(1,3),lowΣREE and low Zr/Hf,Nb/Ta,K/Rb could only be qualitative indicators.Zircon U-Pb ages suggest that the highly evolved gran-ites in the GXR were mainly formed in Late Mesozoic,which can be divided into two major stages:Late Ju-rassic-early Early Cretaceous(162-136 Ma,peak at 138 Ma),and late Early Cretaceous(136-106 Ma,peak at 126 Ma).The highly evolved granites are mainly distributed in the central-southern GXR,and display a weakly trend of getting younger from northwest to southeast,meanwhile indicating the metallogenic potential of rare metals within the central GXR.The spatial-temporal distribution,combined with regional geological data,indicates the highly evolved Mesozoic granites in the GXR were emplaced in an extensional environ-ment,of which the Late Jurassic-early Early Cretaceous extension was related to the closure of the Mongol-Okhotsk Ocean and roll-back of the Paleo-Pacific Plate,while the late Early Cretaceous extension was mainly related to the roll-back of the Paleo-Pacific Plate.

Estimation of Displacement and Extension due to Reverse Drag of Normal Faults: Forward Method

In the case of reverse drag of normal faulting, the displacement and horizontal extension are determined based on the established equations for the three mechanisms: rigid body, vertical shear and inclined shear. There are three sub-cases of basal detachment for the rigid body model: horizontal detachment, antithetic detachment and synthetic detachment. For the rigid body model, the established equations indicate that the total displacement on the synthetic base (Dt2) is the largest, that on the horizontal base (Dt1) is moderate, and that on the antithetic base (Dt3) is the smallest. On the other hand, the value of (Dt1) is larger than the displacement for the vertical shear (Dt4). The value of (Dt1) is larger than or less than the displacement for the inclined shear (Dt5) depending on the original fault dip δ0, bedding angle θ, and the angle of shear direction β. For all original parameters, the value of Dt5 is less than the value of Dt4. Also, by comparing three rotation mechanisms, we find that the inclined shear produces largest extension, the rigid body model with horizontal detachment produces the smallest extension, and the vertical shear model produces moderate extension.

Analysis of the Digital Skill Gap of Agricultural Extension Personnel in South-East, Nigeria

The study analysed the digital skill gap of agricultural extension personnel on the use of digital technologies for extension services delivery in South-East, Nigeria. The specific objectives were to describe the socioeconomic characteristics of agricultural extension personnel in South-East Nigeria and identify the digital skill gaps among agricultural extension personnel in the area of study. Purposive sampling technique was used to select 364 Agricultural Extension personnel for the study. Data were collected through the use of structured questionnaire and were analysed using simple descriptive statistical tools such as percentages, mean score, and standard deviation. Findings indicated that most of the personnel were male (57.8%), within the age bracket of 38 - 47 years (62.9%), had B.Sc./HND as their highest educational qualification (74.7%), married (86.3%), and had a household size of 6 - 10 Persons (57.7%). It was further revealed that the majority (70.1%) were members of professional organization, earned a monthly income of N50,001.00 - N100,000.00 (65.7%), had a work experience of 11 - 15 years (51.1%), and owned a smartphone/ iPad/laptop (91.5%). Findings further indicated that they had moderate skill gap in Basic Computer skills (Mean = 4.32), and digital communication and collaboration skills (Mean = 4.26). Findings also showed that they had a high skill gap in digital technical skills (Mean = 2.46), digital data analysis skills (Mean = 2.09), digital content creation skills (Mean = 2.43), digital ethical skills (Mean = 2.79), multimedia production skills (Mean = 2.81), and video library management skills (Mean = 2.39). The study concluded that though there exists a high digital skill gap among agricultural extension personnel in South-East, Nigeria, their socioeconomic characteristics are capable of supporting the implementation of digital extension services in the area. The study recommended that the management of Agricultural Development Programs in South-East, Nigeria, should provide digital training for extension personnel to close the digital skill gap that currently exists among the personnel.

Comparative Study of the Socioeconomic Characteristics and Digital Literacy Level of Agricultural Extension Personnel in Imo and Ebonyi States, South-East, Nigeria

The study comparatively analysed the socioeconomic characteristics and digital literacy level of Agricultural Extension personnel (AEP) in Ebonyi and Imo States, South-East, Nigeria. The specific objectives were to describe the socioeconomic characteristics of agricultural extension personnel in Ebonyi and Imo States, and to ascertain the digital literacy level of AEP in the studied states. Purposive sampling technique was used to select 312 Agricultural Extension personnel (132 from Ebonyi State Agricultural Development Program and 180 from Imo State Agricultural Development Program) for the study. Data were collected through the use of validated and structured questionnaire, and administered through the help of well-trained enumerators. Data were analysed using simple descriptive statistical tools such as percentages mean score, standard deviation and weighted mean. Findings indicated that they were more male in the both States (55.3% and 57.8%) for Ebonyi and Imo State respectively and that the average age of AEP in Ebonyi and Imo States were 44.7 years and 49.2 years respectively. It was further revealed that the majority (77.3% and 82.8%) had B.Sc./HND as their highest academic qualifications, belonged to professional organisations (62.1% and 75%), and were earning an average monthly income of N58,798 and N62,648 for Ebonyi and Imo State respectively. Also, it was revealed that their mean years of service were 12.4 years and 13.4 years for Ebonyi and Imo State respectively. Almost all of them (87.9% and 95.0%) own a smartphone, had access to the internet (80.3% and 90.0%), but do not own a laptop/ipad (82.6% and 72.8%) for Ebon-yi and Imo State respectively. Results further revealed that Agricultural extension personnel in both Ebonyi and Imo State respectively had low digital literacy level ( = 2.41 and 2.32). The study concluded that AEP in Ebonyi and Imo State respectively had similar socioeconomic characteristics and low level of digital literacy. The study recommended that the management of ADPs in both Ebonyi and Imo State should ensure the training of AEP in digital skills to enhance their digital literacy level to enable them use digital technologies in their work.