Mechanical properties and energy evolutions of burst-prone coal samples with holes and fillings

During the mining process of impact-prone coal seams,drilling pressure relief can reduce the impact propensity of the coal seam,but it also reduces the integrity and strength of the coal mass at the side of the roadway.Therefore,studying the mechanical properties and energy evolution rules of coal samples containing holes and filled structures has certain practical significance for achieving coordinated control of coal mine rockburst disasters and the stability of roadway surrounding rocks.To achieve this aim,seven types of burst-prone coal samples were prepared and subject to uniaxial compression experiments with the aid of a TAW-3000 electro-hydraulic servo testing machine.Besides,the stress–strain curves,acoustic emission signals,DIC strain fields and other data were collected during the experiments.Furthermore,the failure modes and energy evolutions of samples with varying drilled hole sizes and filling materials were analyzed.The results show that the indexes related to burst propensity of the drilled coal samples decline to some extent compared with those of the intact one,and the decline is positively corelated to the diameter of the drilled hole.After hole filling,the strain concentration degree around the drilled hole is lowered to a certain degree,and polyurethane filling has a more remarkable effect than cement filling.Meanwhile,hole filling can enhance the strength and deformation resistance of coal.Hole drilling can accelerate the release of accumulated elastic strain energy,turning the acoustic emission events from low-frequency and high-energy ones to high-frequency and low-energy ones,whereas hole filling can reduce the intensity of energy release.The experimental results and theoretical derivation demonstrate that hole filling promotes coal deformability and strength mainly by weakening stress concentration surrounding the drilled holes.Moreover,the fillings can achieve a better filling effect if their elastic modulus and Poisson’s ratio are closer to those of the coal body.

Effects of water and nitrogen rate on grain-filling characteristics under high-low seedbed cultivation in winter wheat

A high-efficiency mode of high-low seedbed cultivation(HLSC)has been listed as the main agricultural technology to increase land utilization ratio and grain yield in Shandong Province,China.However,limited information is available on the optimized water and nitrogen management for yield formation,especially the grain-filling process,under HLSC mode.A three-year field experiment with four nitrogen rates and three irrigation rates of HLSC was conducted to reveal the response of grain-filling parameters,grain weight percentage of spike weight(GPS),spike moisture content(SMC),and winter wheat yield to water and nitrogen rates.The four nitrogen rates were N1(360 kg ha^(-1) pure N),N2(300 kg ha^(-1) pure N),N3(240 kg ha^(-1) pure N),and N4(180 kg ha^(-1) pure N),respectively,and the three irrigation quotas were W1(120 mm),W2(90 mm),and W3(60 mm),respectively.Results showed that the determinate growth function generally performed well in simulating the temporal dynamics of grain weight(0.989<R^(2)<0.999,where R2 is the determination coefficient).The occurrence time of maximum filling rate(T_(max))and active grain-filling period(AGP)increased with the increase in the water or nitrogen rate,whereas the average grain-filling rate(G_(mean))had a decreasing trend.The final 1,000-grain weight(FTGW)increased and then decreased with the increase in the nitrogen rates and increased with the increase in the irrigation rates.The GPS and SMC had a highly significant quadratic polynomial relationship with grain weight and days after anthesis.Nitrogen,irrigation,and year significantly affected the T_(max),AGP,G_(mean),and FTGW.Particularly,the AGP and FTGW were insignificantly different between high seedbed(HLSC-H)and low seedbed(HLSC-L)across the water and nitrogen levels.Moreover,the moderate water and nitrogen supply was more beneficial for grain yield,as well as for spike number and grain number per hectare.The principal component analysis indicated that combining 240-300 kg N ha^(-1) and 90^(-1)20 mm irrigation quota could improve grain-filling efficiency and yield for the HLSC-cultivated winter wheat.

Grain-filling strategies of wheat of contrasting grain sizes under various planting patterns and irrigation levels

In a study comparing grain filling and yield in a large-and a small-grain-size wheat cultivar under two planting patterns and two irrigation regimes,plastic-covered ridge and furrow planting with sprinkler irrigation increased grain filling and yield in both cultivars.The largest contributors to grain yield were an extended active grain-filling period in Shuangda 1 and an increased mean grain-filling rate in XN538.

Heterogeneous information phase space reconstruction and stability prediction of filling body–surrounding rock combination

Traditional research believes that the filling body can effectively control stress concentration while ignoring the problems of unknown stability and the complex and changeable stress distribution of the filling body–surrounding rock combination under high-stress conditions.Current monitoring data processing methods cannot fully consider the complexity of monitoring objects,the diversity of monitoring methods,and the dynamics of monitoring data.To solve this problem,this paper proposes a phase space reconstruction and stability prediction method to process heterogeneous information of backfill–surrounding rock combinations.The three-dimensional monitoring system of a large-area filling body–surrounding rock combination in Longshou Mine was constructed by using drilling stress,multipoint displacement meter,and inclinometer.Varied information,such as the stress and displacement of the filling body–surrounding rock combination,was continuously obtained.Combined with the average mutual information method and the false nearest neighbor point method,the phase space of the heterogeneous information of the filling body–surrounding rock combination was then constructed.In this paper,the distance between the phase point and its nearest point was used as the index evaluation distance to evaluate the stability of the filling body–surrounding rock combination.The evaluated distances(ED)revealed a high sensitivity to the stability of the filling body–surrounding rock combination.The new method was then applied to calculate the time series of historically ED for 12 measuring points located at Longshou Mine.The moments of mutation in these time series were at least 3 months ahead of the roadway return dates.In the ED prediction experiments,the autoregressive integrated moving average model showed a higher prediction accuracy than the deep learning models(long short-term memory and Transformer).Furthermore,the root-mean-square error distribution of the prediction results peaked at 0.26,thus outperforming the no-prediction method in 70%of the cases.

Treatment of Synovial Cysts in Relation to the Tibial Tunnel of Anterior Cruciate Ligament Grafts by Filling the Tunnel with Acrylic Cement

Introduction: Synovial cyst of the tibial tunnel in connection with anterior cruciate ligament (ACL) reconstruction is a rare but particularly troublesome complication. Medical treatment is often doomed to failure, and surgical treatment usually consists of excising the cyst and filling the tunnel with bone. The aim of this study was to evaluate the results of filling the tunnel with acrylic cement. Hypothesis: Filling the tibial bone tunnel with acrylic cement should eliminate communication between the joint cavity and the pre-tibial surface and prevent cyst recurrence. Patients and Methods: This retrospective series is composed of 13 patients, 9 men and 4 women, mean age 48.5 years (31 to 64) operated on between 2011 and 2019 for an intra- and extraosseous synovial cyst consecutive to the tibial tunnel of an ACL graft. Between 1983 and 2016, 12 of the patients had had a bone graft without bone block fixation (DI-DT or Mac Intosh) and one patient, a bone-bone transplant (KJ). The cyst was of variable size, located on the anteromedial aspect of the proximal end of the tibia, and often painful, warranting consultation. At the time of the initial operation, 9 patients had undergone meniscectomies (6 medial, 2 lateral, 1 double). In 7 knees, there were 7 cartilage lesions in the femorotibial and/or patellofemoral compartments (one stage 1 lesion, 2 stage 2 lesions, 4 stage 3 lesions, and no stage 4 lesions). Only 2 knees had neither cartilage nor meniscus lesions. After curettage of the bone tunnel /− removal of the non-resorbed or PEEK interference screw, the tunnel was filled with acrylic cement /− reinforced with a ligament staple to prevent expulsion. All patients underwent regular follow-up consultations until recovery. Results: At a maximum follow-up of 8 years, only 1 cyst recurred, representing a 7.69% failure rate. It was reoperated with another technique, which involved filling the tibial bone tunnel with bone graft taken from a half-bank head. After recovery, the cyst healed definitively. All patients were able to return to their previous activity within 15 days of surgery. Conclusion: Filling the tibial tunnel with acrylic cement reinforced /− with a ligament staple is a reliable and rapid solution for the treatment of intra- and extra-articular synovial cysts in relation to the tibial tunnel of ACL grafts.

Analysis of the Effectiveness of Modified Non- Traumatic Filling Technology in the Treatment of Pediatric Dental Caries

Objective:To analyze the effectiveness of modified non-traumatic filling technology in the treatment of pediatric dental caries.Methods:Ninety-seven children with dental caries who were treated in our hospital(Panyu Maternal and Child Care Service Center of Guangzhou)from January 2022 to December 2023 were selected and randomly divided into two groups,with 48 cases in the experimental group and 49 in the control group.The experimental group was treated with modified non-traumatic filling techniques,while the control group was treated with conventional filling techniques.Observation indicators such as the total effectiveness of the treatment,incidence of adverse events,treatment compliance,and pain scores were analyzed after the intervention.Result:After intervention,the total effectiveness of the treatment in the experimental group was higher than that in the control group(P<0.05).The incidence of adverse events in the experimental group was lower than that of the control group(P<0.05).The treatment compliance of patients in the experimental group was higher than that in the control group(P<0.05).The pain score of the experimental group was lower than that of the control group(P<0.05).Conclusion:The application of modified non-traumatic filling technology in the treatment of pediatric dental caries showed good therapeutic outcomes.After the intervention,the child’s symptoms were significantly alleviated,the incidence of adverse events such as filling material falling off was reduced,their compliance was improved,and the pain was relieved.This procedure is worth to be promoted for clinical application.

Raw Gangue Filling Mining under Construction —A Case Study in China

In order to recover the strip pillar coal resources, reduce the amount of gangue mountain and realize remediation of the goaf environment in the old mining area, the raw gangue filling mining technology was proposed. According to the previous practical experience, the feasibility of the implementation of raw gangue filling mining technology in the coal-pressed area was analyzed. Through the filling gangue compaction test, the deformation under different loading stages was obtained. Further, a reasonable prediction of the deformation beyond the experimental limited loading load was made based on the experimental results. Through the deformation source analysis of the whole process of gangue filling, the key factors for controlling deformation before, during, and after filling were determined. Additionally, the proportion of deformation during different stages was quantified. Considering the protection of surface buildings, mining fullness of the working face and mining technology, the production parameters of 1209 and 1210 filling working faces were preliminarily determined. Through numerical simulation, the rationality of mining scheme was verified. Based on the practice of 1209 working face and the key factors to control the deformation of gangue filling, the mining system and process in 1210 working face were optimized. According to the measured surface rock movement, raw gangue filling mining technology can meet the requirements of surface building protection level. Especially, this paper provides a method to quantitatively calculate the equivalent mining height (EMH) of raw gangue filling and its mining deformation, which has reference significance for old mining areas.

Tuning Active Metal Atomic Spacing by Filling of Light Atoms and Resulting Reversed Hydrogen Adsorption-Distance Relationship for Efficient Catalysis

Precisely tuning the spacing of the active centers on the atomic scale is of great significance to improve the catalytic activity and deepen the understanding of the catalytic mechanism,but still remains a challenge.Here,we develop a strategy to dilute catalytically active metal interatomic spacing(d_(M-M))with light atoms and discover the unusual adsorption patterns.For example,by elevating the content of boron as interstitial atoms,the atomic spacing of osmium(d_(Os-Os))gradually increases from 2.73 to 2.96?.More importantly,we find that,with the increase in dOs-Os,the hydrogen adsorption-distance relationship is reversed via downshifting d-band states,which breaks the traditional cognition,thereby optimizing the H adsorption and H_2O dissociation on the electrode surface during the catalytic process;this finally leads to a nearly linear increase in hydrogen evolution reaction activity.Namely,the maximum dOs-Os of 2.96?presents the optimal HER activity(8 mV@10 mA cm^(-2))in alkaline media as well as suppressed O adsorption and thus promoted stability.It is believed that this novel atomic-level distance modulation strategy of catalytic sites and the reversed hydrogen adsorption-distance relationship can shew new insights for optimal design of highly efficient catalysts.

FGW1, a protein containing DUF630 and DUF632 domains, regulates grain size and filling in Oryza sativa L.

Grain filling influences grain size and quality in cereal crops. The molecular mechanisms that regulate grain endosperm development remain elusive. In this study, we characterized a filling-defective and grain width mutant, fgw1, whose mutation increased rice seed width mainly via cell division and expansion in grains. Sucrose contents were higher but starch contents lower in the fgw1 mutant during the grainfilling stage, resulting in inferior endosperm of opaque, white appearance with loosely packed starch granules. Map-based cloning revealed that FGW1 encoded a protein containing DUF630/DUF632domains, localized in the plasma membrane with preferential expression in the panicle. RNA interference in FGW1 resulted in increased grain width and weight, whereas overexpression of FGW1 led to slightly narrower kernels and better grain filling. In a yeast two-hybrid assay, FGW1 interacted directly with the 14–3–3 protein GF14f, bimolecular fluorescence complementation verified that the site of interaction was the membrane, and the mutated FGW1 protein failed to interact with GF14f. The expression of GF14f was down-regulated in fgw1, and the activities of AGPase, StSase, and SuSase in the endosperm of fgw1increased similarly to those of a reported GF14f-RNAi. Transcriptome analysis indicated that FGW1 also regulates cellular processes and carbohydrate metabolism. Thus, FGW1 regulated grain formation via the GF14f pathway.

Effects of mechanical vibration on filling and solidification behavior, microstructure and performance of Al/Mg bimetal by lost foam compound casting

Al/Mg bimetal was prepared by lost foam solid-liquid compound casting,and the effects of mechanical vibration on the filling and solidification behavior,microstructure and performance of the bimetal were investigated.Results show that the mechanical vibration has a remarkable influence on the filling and solidification processes.It is found that after mechanical vibration,the filling rate increases and the filling rate at different times is more uniform than that without vibration.In addition,the mechanical vibration also increases the wettability between liquid AZ91D and A356 inlays.The mechanical vibration reduces the horizontal and vertical temperature gradient of the casting and makes the temperature distribution of the whole casting more uniform.Compared to the Al/Mg bimetal without vibration,the shear strength is improved by 39.76%after the mechanical vibration is applied,due to the decrease of the inclusions and Al_(12)Mg_(17) dendrites,and the refinement and uniform distribution of the Mg_(2)Si particles in the interface of the Al/Mg bimetal.

Effects of Heat Stress during Seed Filling Stage on Brassica napus Seed Oil Accumulation and Chlorophyll Fluorescence Characteristics

As global temperature rise,the threat of heat stress to rapeseed production is becoming more obvious.Exploring the response characteristics of two important biological pathways,oil accumulation and photosynthesis,to heat stress during B.napus seed filling is helpful in the genetic improvement of heat-tolerant rapeseed.The effects of heat stress on seed oil accumulation and chlorophyll fluorescence characteristics of 29 B.napus germplasms with different oil content and environmental sensitivity,including 6 rapeseed varieties which exhibited environmentsensitive/insensitive and with high,medium or low oil content,were tested by whole plant heat stress or the in vitro silique culture system.Both assay exhibited similar trend on oil content of the rapeseed germplasms.The heat effect on the chlorophyll fluorescence kinetic parameters F_(v)/F_(m),ETR and Y(Ⅱ)were also consistent.Heat stress significantly decreased oil content,although there was abundant genetic variation on heat tolerance among the genotypes.Correlation analysis showed that the decrease rate of F_(v)/F_(m) of silique heat-stressed B.napus developing seed was positive correlative to the decrease rate of mature seed oil content of the whole plant heat-stressed rapeseed(R=0.9214,P-value<0.01).Overall,the results indicated that heat stress inhibited oil accumulation and photosynthesis in B.napus developing seed.The decrease rate of chlorophyll fluorescence parameter F_(v)/F_(m) of heat-stressed developing seed could be used as the index of heat tolerant rapeseed identification.Further,two heat insensitive rapeseed varieties with high oil content were identified.

Fulfilling Meetings

The annual Two Sessions highlight high-quality development The 14th National People’s Congress (NPC),China’s national legislature, concluded its first session on the morning of 13 March in Beijing,marking the completion of the annual sessions of the NPC and the National Committee of the Chinese People’s Political Consultative Conference (CPPCC), the top political advisory body,known collectively as Two Sessions.

Simulation of mould filling process using smoothed particle hydrodynamics

The implementation of high pressure die casting （HPDC） filling process modeling based on smoothed particle hydrodynamics （SPH） was discussed. A new treatment of inlet boundary was established by discriminating fluid particles from inlet particles. The roles of artificial viscosity and moving least squares method in the present model were compared in the handling pressure oscillation. The final model was substantiated by simulating filling process in HPDC in both two and three dimensions. The simulated results from SPH and finite difference method （FDM） were compared with the experiments. The results show the former is in a better agreement with experiments. It demonstrates the efficiency and precision of this SPH model in describing flow pattern in filling process.

Smoothed particle hydrodynamics modeling and simulation of foundry filling process

A numerical model of foundry filling process was established based on the smoothed particle hydrodynamics（SPH）method.To mimic the constraints that the solid mold prescribes on the filling fluid,a composite treatment to the solid boundaries is elaborately designed.On solid boundary surfaces,boundary particles were set,which exert Lennard-Jones force on approaching fluid particles;inside the solid mold,ghost particles were arranged to complete the compact domain of near-boundary fluid particles.Water analog experiments were conducted in parallel with the model simulations.Very good agreement between experimental and simulation results demonstrates the success of model development.

Effects of Nitrogen Quantity on Grain-filling Characters of Two-line Hybrid Rice with Large Ear

[Objective] The aim was to research effects of N quantity on grain-filling characters of two-line hybrid rice cultivars with large ears. [Method] Peiza 67 and 88, two-line hybridized rice with large ears, were made use of to study on effects of N fertilizer in different quantities （LN： 90 kg/hm2;MN： 180 kg/hm2;HN： 270 kg/hm2） on plumpness and grain-filling characters. [Result] When N fertilizers were excessive, for inferior grains, grain-filling rate decreased and grain-filling time extended, resulting in plumpness decline after degradation of leaves＇ function. When N fertilizers were inadequate, maximal and average grain-filling rates decreased and the differences between superior and inferior grains in grain-filling rate increased, leading to decline of grain＇s weight and plumpness degree. On the other hand, quantity of N fertilizers had little effect on superior grains in plumpness. [Conclusion] The research provided references for reasonable use of N fertilizer and improvement of rice yield and N use.

Grain-filling characteristics and yield differences of maize cultivars with contrasting nitrogen efficiencies

To investigate the effect of nitrogen management on the grain-filling characteristics and yield formation of maize cultivars with contrasting nitrogen efficiencies,and to identify differences in grain-filling characteristics and yield of maize cultivars in response to nitrogen management,a two-year field experiment was conducted in southwest China in2015–2016.The grain-filling rate and duration of the N-inefficient cultivar XY 508 were higher than those of the N-efficient cultivar ZH 311.The 100-kernel weight of XY 508 was significantly higher than that of ZH 311.The kernel number per ear of ZH 311 was significantly higher than that of XY 508,making the population filling rate of ZH 311 significantly higher than that of XY 508.The higher population filling rate of the N-efficient maize cultivar led to a significant yield advantage over the N-inefficient maize cultivar.Nitrogen management effectively improved maize grain yield,but the response of maize cultivars with contrasting nitrogen efficiencies to nitrogen management was inconsistent.A basal fertilizer ratio 60.43%with a topdressing ratio 39.57%effectively increased grainfilling rate,delayed the time to maximum filling rate,prolonged the active filling period and effective grain-filling time,increased the 100-kernel weight,and maintained higher kernels per ear,thereby improving the population filling rate and maximizing the yield advantage of the N-efficient cultivar.A 100%basal fertilizer ratio not only increased the number of kernels per ear,but also maintained high grain filling characteristics to obtain a higher 100-kernel weight and increased the population filling rate,leading to a high grain yield in the N-inefficient cultivar.Thus,the 100%basal fertilizer ratio partially compensated for the deficient grain yield of the N-inefficient cultivar.

New filling system design for bolster casting and computer simulation

The new filling system is smooth filling without gas gap. It works well in avoiding the generation of defects such as porosity and inclusion. The pouring basin, sprue, runner and the gate of the bolster casting were designed according to the principle of the new filling system. The filling and solidifciation process of the bolster casting were also simulated. It was found that the filling process was smooth, and air entrapment and shrinkage were avoided. Finally, a further validation of the new filling system of bolster casting was carried out in a foundry.

New numerical algorithm of gas-liquid two-phase flow considering characteristics of liquid metal during mold filling

A new program is developed for gas-liquid two-phase mold filling simulation in casting. The gas fluid, the superheated liquid metal and the liquid metal containing solid grains are assumed to be governed by Navier-Stokes equations and solved through Projection method. The Level set method is used to track the gas-liquid interface boundary. In order to demonstrate the correctness of this new program for simulation of gas-liquid two-phase mold filling in casting, a benchmark filling experiment is simulated （this benchmark test is designed by XU and the filling process is recorded by a 16-mm film camera）. The simulated results agree very well with the experimental results, showing that this new program can be used to properly predicate the gas-liquid two-phase mold filling simulation in casting.

Peripheral arterial filling time and peripheral retina fluorescence features in ultra-widefield angiography

AIM:To evaluate the peripheral arterial filling time(PAFT)and venous filling time(VFT)in eyes without known diseases that may influence filling process using ultra-widefield(UWF)fluorescein angiography(FA),and to review the peripheral retina fluorescence features.METHODS:A total of 30 eyes of 30 patients were retrospectively reviewed in this observational study.UWFFA was performed using Optos 200Tx.PAFT and VFT was recorded.The interval between the arterial or venous filling completion and the previous photo was documented.The appearance of the far peripheral retina was described as either granular background fluorescence or mottled fluorescent band or vascular leakage.Terminal vascular patterns was described as loop pattern or branching pattern.Microvascular abnormalities such as arteriovenous shunting,vessels crossing the horizontal raphe,right angle vessels,terminal networks,capillary nonperfusion,drusen or microaneurysms were evaluated.RESULTS:The normal limits of PAFT was 3.397-8.984s and 4.399-11.753s for VFT.The appearance of the far peripheral retina,defined as granular background(63%),mottled fluorescence(20%),or vascular leakage(17%),was symmetrical between both eyes.Capillary nonperfusion(23%)and microaneurysms(40%)were more frequently found in eyes with loop pattern than in eyes with branching pattern.Other peripheral signs such as right-angle vessels(73%),and terminal networks(80%)were commonly seen on UWF-FA in the normal peripheral retina.CONCLUSION:The main courses of retinal artery and vein filling time are overlapping with each other on UWF-FA.Notably,the arterial filling process is completed in the arteriovenous phase rather than the traditionally named arterial phase.There are various manifestations in the peripheral retina of normal eyes.

一种基于红外成像障碍物检测的改进Flood Filling算法

在对图像特征进行有效分割的基础上,提出了一种基于红外成像障碍物检测的改进Flood Filling算法,并首次将该算法应用到障碍物检测领域中。通过对模拟以及真实红外图像中目标的快速成功提取,不仅验证了该方法的有效性,同时实验结果也表明了其较之原始算法对时效性的提高。