975 nm multimode semiconductor lasers with high-order Bragg diffraction gratings

The 975 nm multimode diode lasers with high-order surface Bragg diffraction gratings have been simulated and calcu-lated using the 2D finite difference time domain(FDTD)algorithm and the scattering matrix method(SMM).The periods and etch depth of the grating parameters have been optimized.A board area laser diode(BA-LD)with high-order diffraction grat-ings has been designed and fabricated.At output powers up to 10.5 W,the measured spectral width of full width at half maxi-mum(FWHM)is less than 0.5 nm.The results demonstrate that the designed high-order surface gratings can effectively nar-row the spectral width of multimode semiconductor lasers at high output power.

Enhancing the Goos-Hänchen shift based on quasi-bound states in the continuum through material asymmetric dielectric compound gratings

Quasi-bound state in the continuum(QBIC)resonance is gradually attracting attention and being applied in Goos-Hänchen(GH)shift enhancement due to its high quality(Q)factor and superior optical confinement.Currently,symmetry-protected QBIC resonance is often achieved by breaking the geometric symmetry,but few cases are achieved by breaking the material symmetry.This paper proposes a dielectric compound grating to achieve a high Q factor and high-reflection symmetry-protectede QBIC resonance based on material asymmetry.Theoretical calculations show that the symmetry-protected QBIC resonance achieved by material asymmetry can significantly increase the GH shift up to-980 times the resonance wavelength,and the maximum GH shift is located at the reflection peak with unity reflectance.This paper provides a theoretical basis for designing and fabricating high-performance GH shift tunable metasurfaces/dielectric gratings in the future.

Wavelength-tunable organic semiconductor lasers based on elastic distributed feedback gratings

Wavelength-tunable organic semiconductor lasers based on mechanically stretchable polydimethylsiloxane (PDMS) gratings were developed. The intrinsic stretchability of PDMS was explored to modulate the period of the distributed feedback gratings for fine tuning the lasing wavelength. Notably, elastic lasers based on three typical light-emitting molecules show com-parable lasing threshold values analogous to rigid devices and a continuous wavelength tunability of about 10 nm by mechanic-al stretching. In addition, the stretchability provides a simple solution for dynamically tuning the lasing wavelength in a spec-tral range that is challenging to achieve for inorganic counterparts. Our work has provided a simple and efficient method of fab-ricating tunable organic lasers that depend on stretchable distributed feedback gratings, demonstrating a significant step in the advancement of flexible organic optoelectronic devices.

Simulation research on surface growth process of positive and negative frequency detuning chromium atom lithographic gratings

Chromium atom photolithography gratings are a promising technology for the development of nanoscale length standard substances due to their high accuracy,uniformity,and consistency.However,the inherent difference between the interaction of positive and negative frequency detuning standing wave field and the atoms can cause a difference in the adjacent peak-to-valley heights of the grating in positive and negative frequency detuning chromium atom lithography,which greatly reduces its accuracy.In this study,we performed a controlled variable growth simulation using the semi-classical theoretical model and Monte Carlo method with trajectory tracking and ballistic deposition methods to investigate the influence of key experimental parameters on the surface growth process of positive and negative frequency detuning atomic lithography gratings.We established a theoretical model based on simulation results and summarized empirical equations to guide the selection of experimental parameters.Our simulations achieved uniform positive and negative frequency detuning atomic lithography gratings with a period of 1/4 of the wavelength corresponding to the atomic transition frequency,and adjacent peak-to-valley heights differing by no more than 2 nm,providing an important theoretical reference for the controllable fabrication of these gratings.

Ultra-High Temperature Gratings

Regenerated gratings seeded by type-I gratings are shown to withstand temperatures beyond 1000 ℃. The method of regeneration offers a new approach to increasing temperature resistance of stable fibre Bragg and other gratings. These ultra-high temperature （UHT） gratings extend the applicability of silicate based components to high temperature applications such as monitoring of smelters and vehicle and aircraft engines to high power fibre lasers.

Spectral Beam Combining of Fiber Lasers by Using Reflecting Volume Bragg Gratings

By employing three reflecting volume Bragg gratings, a near-infrared 4-channel spectral-beam-combining system is demonstrated to present 720 W combined power with a combining efficiency of 94.7%. The combined laser beam is near-diffraction-limited with a beam factor M^2-1.54. During this 4-channel beam-combining process, no special active cooling measures are used to evaluate the volume Bragg gratings as combining elements are under the higher power laser operation. Thermal expansion and period distortion are verified in a 2 k W 2-channel beam-combining process, and the heat issue in the transmission case is found to be more remarkable than that in the diffraction e-se. Transmitted and diffracted beams experience wave-front aberrations with different degrees, thus leading to distinct beam deterioration.

Optimal design of sub-wavelength metal rectangular gratings for polarizing beam splitter based on effective medium theory

A novel optimal design of sub-wavelength metal rectangular gratings for the polarizing beam splitter （PBS） is proposed. The method is based on effective medium theory and the method of designing single layer antireflection coating. The polarization performance of PBS is discussed by rigorous couple-wave analysis （RCWA） method at a wavelength of 1550 nm. The result shows that sub-wavelength metal rectangular grating is characterized by a high reflectivity, like metal films for TE polarization, and high transmissivity, like dielectric films for TM polarization. The optimal design accords well with the results simulated by RCWA method.

Engineering approach to in-situ bridge health monitoring with fiber bragg gratings

In this presentation the feasibility and capability of fiber Bragg gratings （FBG） employed in bridge health monitoring are demonstrated on a real bridge. FBG＇ s wavelength shift depending on strain variance has been tested. The technique of FBG installation on bridges has been developed. 12 FBG strain sensors and 3 temperature sensors have been successfully embedded in the prestressed concrete box girder during the construction of Heilongjiang Hulan River Bridge. The prestressing tension process and quasi-static loading process of the girder were monitored with those sensors before it was installed onto the bridge. After the bridge was completed, the FBG sensors embedded have been utilized to monitor the strain shift of the beam under quasi-static load, traffic load and temperature. The results show that the traffic fluxes, possible tatigue damage and deflection of the bridge can be revealed conveniently through strain measurements with these FBG sensors, which provide key information for structural health diagnosis. The fact that the FBG strain sensors have withstood the ordeal of harsh construction process and lasted for more than one year proves that their durability and stability can satisfy the requirements for bridge health monitoring. It is also shown that the FBG strain sensor is more adaptive to long-term structural health monitoring than the electric resistance strain gauge.

Investigation of transmission resonances on the one-dimensional metallic cylindrical gratings in THz frequency range

In the experiments of THz wave transmitting through the metallic cylindrical gratings fabricated by sub-wavelength brass wires, this paper reports that the discrepancy in the sharp resonances occurred as the grating perpendicular or parallel to the electric vector are observed. A simulation based on the finite difference time domain （FDTD） indicated that the enhanced transmission through the grating is attributed to the combined effects of surface plasmons and cavity modes in the perpendicular condition, while the cavity modes dominate the resonant transmission under the other conditions. Additional experimental data and calculated results show that ~1 enhanced coupling efficiency can be realized in some THz frequency, which could be applied to the design and improvement of various optoelectronic devices, or detection of biological molecule and powder samples, etc.

Fabrication and Evaluation of Bragg Gratings on Optimally Designed Silicon-on-Insulator Rib Waveguides Using Electron-Beam Lithography

The fabrication of Bragg gratings on silicon-on-insulator （SOI） rib waveguides using electron-beam lithography is presented. The grating waveguide is optimally designed for actual photonic integration. Experimental and theoretical evaluations of the Bragg grating are demonstrated. By thinning the SOl device layer and deeply etching the Bragg grating, a large grating coupling coefficient of 30cm^-1 is obtained.

Fabrication of arbitrarily apodized fiber Bragg gratings with narrow bandwidth

A double-exposure fabrication method without any intensity shadow mask to fabricate arbitrarily apodized fiber Bragg gratings（ FBGs） with narrow bandwidth is demonstrated by controlling the total ultra violet （UV） irradiation along the grating by varying the speed of a translation stage. The UV source used is a stable continuous intracavity frequency-doubled argonion laser. The parameters （such as length, apodization profile, average index change）of FBGs can be easily changed with this method. The total UV irradiation is kept constant in the doubleexposure process because of the precise control of the exposure time, which ensures that the apodized FBG＇s bandwidth can be extremely narrow. The full width at half maximum （FWHM） bandwidth of the 2-cm-long apodized FBG fabricated by this method is 0. 15 nm with a maximum reflectivity of more than 95%.

Rigorous Coupled-Wave Approach for Sandwich Gratings

Rigorous Coupled-Wave Approach (RCWA) has been used successfully and accurately to study simple grating structures, such as one-layer gratings, one-whole gratings. In this paper, RCWA is expanded to solve Sandwich gratings (SG), which is composed of two identical planar dielectric gratings adjoined by thin metallic or dielectric film. The electromagnetic analytic expressions for each layer of SG structure are given and rigorous coupled-wave equations are deduced. The numerical investigations for the diffraction spectra of SG by our theoretical and computer programs are in good agreement with the results of classical RCWA in the condition when a Sandwish grating is simplified to a classical one-layer grating. The calculations by our programs of another condition when a Sandwish grating is degenerated to a classical single planar structure also conform to the results of classical electromagnetic theory. The research results above indicate that the extended theoretical formula has backwards compatibility and is self-consistent with the classical theory.

A simulation program for analysing fiber optic Bragg gratings

ＡｓｉｍｕｌａｔｉｏｎｐｒｏｇｒａｍｆｏｒａｎａｌｙｓｉｎｇｆｉｂｅｒｏｐｔｉｃＢｒａｇｇｇｒａｔｉｎｇｓＰｅｔｅｒＫＣＣｈａｎ，Ｗ．Ｄｕ，Ｗ．Ｊｉｎ，Ｍ．Ｓ．Ｄｅｍｏｋａｎ（Ｄｅｐｔ．ｏｆＥｌｅｃｔｒ．Ｅｎｇ．，ＨｏｎｇＫｏｎｇＰｏｌｙｔｅｃｈｎｉ...

Convention of Optical Vortices in Two-Helix Long-Period Fiber Gratings

An effective method to fabricate two-helix long-period fiber gratings （TH-LFGs） is presented. Based on the coupling mode theory, the conversion of optical vortices （OVs） in TH-LFGs are analyzed in detail. The conversions of OVs with different topological charges： 0 → ±2 and 1 → 3 are simulated as three examples and the conversion efficiency higher than 98% can be realized.

Dual-function beam splitter of high contrast gratings

we preset the design and rabrication of a novel auai-iunction hign contrast gratings that can De usea as a polarizationselective beam splitter with transverse magnetic polarization,which performs two independent functions,i.e.,reflection focusing and power equalization at a wavelength of 1550 nm.This dual-function grating profile is optimized by the rigorous coupled-wave analysis and the finite-element method.Simple analytical expressions of phase and modal guideline for the beam splitter design are given.The beam splitter based on the grating structure is experimentally studied at a distance of 160 μm from the reflection plane,the results are consistent with the theoretical results basically.

Dynamic analysis of holographic gratings in a multi-wavelength visible light sensitive photopolymer

A dynamic theoretical model of photochemistry and hologram formation in holographic photopolymer is established, and the dynamic development process of holographic gratings in the photopolymer is discussed with the model. A novel multi-wavelength visible light sensitive photopolymer for holographic storage is prepared. The influence of exposure wavelength on holographic storage characteristics is analysed. By fitting the experimental data of transmittance and diffraction efficiency to a function of time with different exposure intensities and wavelengths, the variations of dynamic parameters of photochemistry and photopolymerization diffusion are presented.

Fiber Bragg Gratings in Small-Core Ge-Doped Photonic Crystal Fibers

This paper reports fiber Bragg gratings （FBGs） inscribed in a small-core Ge-doped photonic crystal fibers with a UV laser and a Talbot interferometer. The responses of such FBGs to temper- ature, strain, bending, and transverse-loading were systematically investigated. The Bragg wavelength of the FBGs shifts toward longer wavelengths with increasing temperature, tensile strain, and transverse-loading. The bending and transverse- loading properties of the FBGs are sensitive to the fiber orientations.

Two-dimensional non-spatial filtering based on holographic Bragg gratings

The filter made up of two gratings performs as a two-dimensional non-spatial filtering. This paper reports that the volume Bragg gratings are fabricated by interfering two collimated coherent laser beams in photopolymer. Diffraction efficiency of a single grating is up to 78% in Bragg＇s condition, then a two-dimensional non-spatial filter, which consists of two volume Bragg gratings and a half-wave plate, enables the laser beam filtered in two dimensions with the diffraction efficiency of 54%. The Bragg＇s condition and effect of polarisation on performances of the two-dimension filter are also discussed.

Resonant Effects of FPL and SPP for Light Transmitting through Subwavelength Metallic Gratings

A new model is proposed to explain the physical mechanism of the extraordinary transmission enhancement in subwavelength metallic grating.The extraordinary transmission enhancement is described by the co-operation of Fabry-Perot-like(FPL) resonance and the surface plasmon polariton(SPP) resonance.The rigorous coupled-wave analysis(RCWA) and the finite difference time domain(FDTD) method are employed to illustrate the model by calculating the transmission and the field distributions in the subwavelength metallic grating,respectively.And the numerical calculations show that transmission enhancement is achieved when the coupling resonance of the incident light,the surface plasmon polariton mode and the Fabry-Perot-Like mode is happened,which are in good agreement with the proposed model.

Coupling characteristics of laterally coupled gratings with slots

Laterally-coupled ridge-waveguide distributed feedback lasers fabricated without epitaxial regrowth steps have the advantages of process simplification and low cost.We present a laterally coupled grating with slots.The slots etched between the ridge and grating area are designed to suppress the lateral diffusion of carriers and to reduce the influence of the aspect-ratio-dependent-etching effect on the grating morphology in the etching process.Moreover,the grating height in this structure can be decreased to lower the aspect ratio significantly,which is advantageous over the conventional laterally coupled ridge waveguide gratings.The effects of five main structural parameters on the coupling characteristics of gratings are studied by MODE Solutions.It is found that varying the lateral width of the grating can be used as an effective way to tune the coupling strength;narrow slots(100 nm and 300 nm)and wide ridge(2μm–4μm)promote the stability of grating coupling coefficient and device performance.It is important to note that the grating bottom should be fabricated precisely.The comparative study of carrier distribution and mode field distribution shows that the introduction of narrow slots can strengthen the competitive advantage and stability of the fundamental mode.