Analysis of the Impact of Thermochemical Recuperation of Waste Heat on the Energy Efficiency of Gas Carriers

Enlarging the fleet of gas carriers would make it possible to respond to the growing demand for hydrocarbon gases,but it will increase carbon dioxide emissions.The International Maritime Organization(IMO)has developed the energy efficiency design index(EEDI)with the objective of carbon emission reduction for new ships.In this paper,thirty gas carriers transporting liquefied natural gas(LNG)and liquefied petroleum gas(LPG)and equipped with various types of main engines are considered.As shown by the calculation of the attained EEDI,2 of the 13 LPG carriers and 6 of the 17 LNG carriers under study do not comply with the EEDI requirements.To meet the stringent EEDI requirements,applying thermochemical regenerators(TCRs)fed by main engine exhaust gases is suggested.Mathematical modeling is applied to analyze the characteristics of the combined gas-turbine-electric and diesel-electric power plant with thermochemical recuperation of the exhaust gas heat.Utilizing TCR on gas carriers with engines fueled by syngas produced from boil-off gas(BOG)reduces the carbon content by 35%and provides the energy efficiency required by IMO without the use of other technologies.

Assessment of Site Parameters and Heat Recovery Characteristics on Combined Cycle Performance in an Equatorial Environment

This paper investigates the effects of site based parameters such as ambient temperature, humidity, altitude and heat transfer characteristic of a dual pressure heat recovery system on the performance of the combined cycle power plant within an equatorial environment. The bulk heat utilization and configuration of a dual pressure heat recovery system are investigated. It is observed that the heat system configuration play a vital role in optimizing the combined cycle overall performance, which has proportionality relationship with the operating ambient temperature and relative humidity of the gas turbine. The investigation is carried out within the ambient temperature range of 24℃ to 35℃, relative humidity of 60% to 80%, and a high level steam pressure of 60 bar to 110 bar. The results show that at 24℃ ambient temperature, the heat recovery system has the highest duty of 239.4 MW, the optimum combined cycle power output of 205.52 MW, and overall efficiency of 47.46%. It further indicates that as the ambient temperature increases at an average exhaust gas temperature of 530℃ and mass flow of 470 kg/s, the combined cycle power output and efficiency decrease by 15.5% and 13.7% respectively under the various considerations. This results from a drop in the air and exhaust mass flow as the values of the site parameters increase. The overall results indicate that decreasing the ambient temperature at optimum exhaust gas flow and temperature increases the heat recovery system heat duty performance, the steam generation, overall combined cycle power output and efficiency, which satisfies the research objective.

Thermodynamic Performance Analysis of a Gas Turbine in an Equatorial Rain Forest Environment

This paper discusses the thermodynamic analysis of a gas turbine power plant located in the equatorial rainforest of southern Nigeria. Steady state monitoring and direct collection of data from the Mk IV Speedtronics system and log books in the control room was performed. The variation of operating conditions (ambient temperature, compressor discharge temperature, turbine inlet temperature, exhaust temperature and fuel mass flow rate) on the performance of gas turbine (thermal efficiency, net power output, heat rate, specific fuel consumption and compressor work) were investigated using various thermodynamic relations and equations. The results show that a degree rise in ambient temperature could be responsible for the following: 1.37% reduction in the net power output, 1.48% increase in power drop, 1.49% reduction in thermal efficiency, 2.16% increase in heat rate, 2.17% increase in specific fuel consumption and 0.3% increase in compressor work. Furthermore the thermal efficiency decreases by 0.006% for 1 kcal/kWh increase in heat rate and the heat transfer in the hot gas part was found to increase by 0.16% for a degree rise in ambient temperature. Also the work reveals that the gas turbine had a huge drop in power due to influence of site parameters in contrast to designed data.

Structural and Conceptual Design Analysis of an Axial Compressor for a 100 MW Industrial Gas Turbine (IND100)

The structural design of the IND100 axial compressor requires a multistage interrelationship between the thermodynamic, aerodynamic, mechanical design and structural integrity analysis of the component. These design criteria, sometimes act in opposition, hence engineering balance is employed within the specified design performance limits. This paper presents the structural and conceptual design of a sixteen stage single shaft high pressure compressor of IND100 with an overall pressure ratio of 12 and mass flow of 310 kg/s at ISOSLS conditions. Furthermore, in order to evaluate the conceptual design analysis, basic parameters like compressor sizing, load and blade mass, disc stress analysis, bearings and material selections, conceptual disc design and rotor dynamics are considered using existing tools and analytical technique. These techniques employed the basic thermodynamic and aerodynamic theory of axial flow compressors to determine the temperature and pressure for all stages, geometrical parameters, velocity triangle, and weight and stress calculations of the compressor disc using Sagerser Empirical Weight Estimation. The result analysis shows a constant hub diameter annulus configuration with compressor overall axial length of 3.75 m, tip blade speed of 301 m/s, maximum blade centrifugal force stress of 170 MPa, with major emphasis on industrial application for the structural component design selections.

A Non-Dimensional Consideration in Combustor Axial Stress Computations

Thermal stresses in the combustor of gas-turbines are computed using non-dimensional parameters. Buckingham pi theorem was used to arrange the listed relevant parameters into non-dimensional groups. In testing the validity of the functional relation of the non-dimensional independent parameters, use is made of the prevailing temperatures of the combustor in operation. A computer program was used to enhance computations. The results showed an interesting way of influencing the axial stresses. To reduce stresses in gas-turbine combustors, a method of varying the independent parameter that is of radius ratio oriented and thickness dependent was adopted. This showed a reduction of the axial stresses to minimal levels using the parameters. Plots were made and a point of inflection that manifested itself in the presentation of the axial stress function was further investigated upon. It turned out to be a point of abnormal stress level and out-of-trend temperature profile. The use of non-dimensional consideration proved adequate in the computation of axial stresses. The results showed a 2 percent difference from existing values of stresses got from a transient thermal loading of a combustor.

HTGR Process Heat Application Study

The 10MW high temperature gas-cooled reactor test module (HTR-10) is currently under construction.One of its objectives is to develop high temperature process heat applications. To realize this target, various high temperature gas-cooled reactor (HTGR) process heat applications have been analyzed. This paper briefly describes the possibilities and experimental schemes for using the HTR-10 for process heat application studies.