High Ga content Cu(In,Ga)Se2 thin films incorporated sulfur were prepared by sequential evaporation from CuGaSe2 and CuInSe2 ternary compounds and subsequently Ga2Se3, In2Se3 and In2S3 binary compounds. The In2S3/(Ga2...High Ga content Cu(In,Ga)Se2 thin films incorporated sulfur were prepared by sequential evaporation from CuGaSe2 and CuInSe2 ternary compounds and subsequently Ga2Se3, In2Se3 and In2S3 binary compounds. The In2S3/(Ga2Se3+ In2Se3) ratio was varied from 0 to 0.13, and the properties of the thin films were investigated. XRD studies demonstrated that the prepared thin films had a chalcopyrite Cu(In,Ga)Se2 structure. The S/(Se+S) mole ratio in the thin films was within the range from 0 to 0.04. The band gaps of Cu(In,Ga)Se2 thin films increased from 1.30 eV to 1.59 eV with increasing the ?In2S3 /(Ga2Se3+ In2Se3) ratio.展开更多
TiC-TiB2-Cu composites were produced by self-propagating high-temperature synthesis combined with pseudo hot isostatic pressing using Ti, B4C and Cu powders. The microstructure and mechanical properties of the composi...TiC-TiB2-Cu composites were produced by self-propagating high-temperature synthesis combined with pseudo hot isostatic pressing using Ti, B4C and Cu powders. The microstructure and mechanical properties of the composites were investigated. The X-ray diffraction （XRD） and scanning electron microscopy （SEM） results showed that the final products were only TiC, TiB2 and Cu phases. The clubbed TiB2 grains and spheroidal or irregular TiC grains were found in the microstructure of synthesized products. The reaction temperature and grain size of TiB2 and TiC particles decreased with increasing Cu content. The introduction of Cu into the composites resulted in a drastic increase in the relative density and flexual strength, and the maximum values were obtained with the addition of 20 wt pct, while the fracture toughness was the best when Cu content was 40 wt pct.展开更多
利用Gleeble-1500D热模拟机,在温度为550,650,750,850,900℃,应变速率为0.001,0.01,0.1,1,10 s^(-1)的条件下,对Cu-1%Zr-0.15%Ce合金的高温变形过程中的流变应力进行研究,分析了动态再结晶的演变机制。结果表明:变形温度和应变速率对合...利用Gleeble-1500D热模拟机,在温度为550,650,750,850,900℃,应变速率为0.001,0.01,0.1,1,10 s^(-1)的条件下,对Cu-1%Zr-0.15%Ce合金的高温变形过程中的流变应力进行研究,分析了动态再结晶的演变机制。结果表明:变形温度和应变速率对合金的流变应力有显著的影响,在550~750℃之间具有典型的动态回复特征,850~900℃具有动态再结晶热变形特征。通过流变应力、应变速率和变形温度之间的关系,建立高温热变形流变应力本构方程,得到合金的热激活能为430.51 k J·mol^(-1),与纯铜热压缩变形过程相比,高Zr含量Cu-1%Zr-0.15%Ce合金热激活能提高了105%。展开更多
The Ti6Al4V-Cu alloy was reported to show good antibacterial properties, which was promising to reduce the hazard of the bacterial infection problem. For the purpose of preparing Ti6Al4V-Cu alloy with satisfied compre...The Ti6Al4V-Cu alloy was reported to show good antibacterial properties, which was promising to reduce the hazard of the bacterial infection problem. For the purpose of preparing Ti6Al4V-Cu alloy with satisfied comprehensive properties, it’s important to study the heat treatment and the appropriate Cu content of the alloy. In this study, high Cu content Ti6Al4V-x Cu(x = 4.5, 6, 7.5 wt%) alloys were prepared, and firstly the annealing heat treatments were optimized in the α+β+Ti2Cu triple phase region to obtain satisfied tensile mechanical properties. Then the effect of Cu content on the tribological property, corrosion resistance, antibacterial activity and cytotoxicity of the Ti6Al4 V-x Cu alloys were systematically studied to obtain the appropriate Cu content. The results showed that the optimal annealing temperatures for Ti6Al4 V-x Cu(x = 4.5, 6, 7.5 wt%) alloys were 720, 740 and 760℃, respectively, which was resulted from the proper volume fractions of α,β and Ti2Cu phases in the microstructure. The additions of 4.5 wt% and 6 wt% Cu into the medical Ti6Al4 V alloy could enhance the wear resistance and corrosion resistance of the alloy, but the addition of 7.5 wt% Cu showed an opposite effect. With the increase of the Cu content, the antibacterial property was enhanced due to the increased volume fraction of Ti2Cu phase in the microstructure, but when the Cu content was increased to 7.5 wt%, cytotoxicity was presented. A medium Cu content of 6 wt%, with annealing temperature of 740℃ make the alloy possesses the best comprehensive properties of tensile properties, wear resistance, corrosion resistance, antibacterial property and biocompatibility, which is promising for future medical applications.展开更多
文摘High Ga content Cu(In,Ga)Se2 thin films incorporated sulfur were prepared by sequential evaporation from CuGaSe2 and CuInSe2 ternary compounds and subsequently Ga2Se3, In2Se3 and In2S3 binary compounds. The In2S3/(Ga2Se3+ In2Se3) ratio was varied from 0 to 0.13, and the properties of the thin films were investigated. XRD studies demonstrated that the prepared thin films had a chalcopyrite Cu(In,Ga)Se2 structure. The S/(Se+S) mole ratio in the thin films was within the range from 0 to 0.04. The band gaps of Cu(In,Ga)Se2 thin films increased from 1.30 eV to 1.59 eV with increasing the ?In2S3 /(Ga2Se3+ In2Se3) ratio.
基金The work was supported by the Foundation of Aerospace Innovation Fund and the National Natural Science Foundation of China(No.90505015)the Foundation of National Key Laboratory for Remanufacturing.
文摘TiC-TiB2-Cu composites were produced by self-propagating high-temperature synthesis combined with pseudo hot isostatic pressing using Ti, B4C and Cu powders. The microstructure and mechanical properties of the composites were investigated. The X-ray diffraction （XRD） and scanning electron microscopy （SEM） results showed that the final products were only TiC, TiB2 and Cu phases. The clubbed TiB2 grains and spheroidal or irregular TiC grains were found in the microstructure of synthesized products. The reaction temperature and grain size of TiB2 and TiC particles decreased with increasing Cu content. The introduction of Cu into the composites resulted in a drastic increase in the relative density and flexual strength, and the maximum values were obtained with the addition of 20 wt pct, while the fracture toughness was the best when Cu content was 40 wt pct.
文摘利用Gleeble-1500D热模拟机,在温度为550,650,750,850,900℃,应变速率为0.001,0.01,0.1,1,10 s^(-1)的条件下,对Cu-1%Zr-0.15%Ce合金的高温变形过程中的流变应力进行研究,分析了动态再结晶的演变机制。结果表明:变形温度和应变速率对合金的流变应力有显著的影响,在550~750℃之间具有典型的动态回复特征,850~900℃具有动态再结晶热变形特征。通过流变应力、应变速率和变形温度之间的关系,建立高温热变形流变应力本构方程,得到合金的热激活能为430.51 k J·mol^(-1),与纯铜热压缩变形过程相比,高Zr含量Cu-1%Zr-0.15%Ce合金热激活能提高了105%。
基金financially supported by the National Key Research and Development Program of China (Nos. 2018YFC1106600 and 2016YFC1100600)the Innovation Fund Project of Institute of Metal Research, Chinese Academy of Sciences (No. 2017-ZD01)+1 种基金the National Natural Science Foundation (Nos. 51631009 and 51811530320)Key Projects for Foreign Cooperation of Bureau of International Cooperation Chinese Academy of Sciences (No. 174321KYSB2018000)
文摘The Ti6Al4V-Cu alloy was reported to show good antibacterial properties, which was promising to reduce the hazard of the bacterial infection problem. For the purpose of preparing Ti6Al4V-Cu alloy with satisfied comprehensive properties, it’s important to study the heat treatment and the appropriate Cu content of the alloy. In this study, high Cu content Ti6Al4V-x Cu(x = 4.5, 6, 7.5 wt%) alloys were prepared, and firstly the annealing heat treatments were optimized in the α+β+Ti2Cu triple phase region to obtain satisfied tensile mechanical properties. Then the effect of Cu content on the tribological property, corrosion resistance, antibacterial activity and cytotoxicity of the Ti6Al4 V-x Cu alloys were systematically studied to obtain the appropriate Cu content. The results showed that the optimal annealing temperatures for Ti6Al4 V-x Cu(x = 4.5, 6, 7.5 wt%) alloys were 720, 740 and 760℃, respectively, which was resulted from the proper volume fractions of α,β and Ti2Cu phases in the microstructure. The additions of 4.5 wt% and 6 wt% Cu into the medical Ti6Al4 V alloy could enhance the wear resistance and corrosion resistance of the alloy, but the addition of 7.5 wt% Cu showed an opposite effect. With the increase of the Cu content, the antibacterial property was enhanced due to the increased volume fraction of Ti2Cu phase in the microstructure, but when the Cu content was increased to 7.5 wt%, cytotoxicity was presented. A medium Cu content of 6 wt%, with annealing temperature of 740℃ make the alloy possesses the best comprehensive properties of tensile properties, wear resistance, corrosion resistance, antibacterial property and biocompatibility, which is promising for future medical applications.
