Effects of the initiation position on the damage and fracture characteristics of linear-charge blasting in rock

To study the effects of the initiation position on the damage and fracture characteristics of linear-charge blasting, blasting model experiments were conducted in this study using computed tomography scanning and three-dimensional reconstruction methods. The fractal damage theory was used to quantify the crack distribution and damage degree of sandstone specimens after blasting. The results showed that regardless of an inverse or top initiation, due to compression deformation and sliding frictional resistance, the plugging medium of the borehole is effective. The energy of the explosive gas near the top of the borehole is consumed. This affects the effective crushing of rocks near the top of the borehole, where the extent of damage to Sections Ⅰ and Ⅱ is less than that of Sections Ⅲ and Ⅳ. In addition, the analysis revealed that under conditions of top initiation, the reflected tensile damage of the rock at the free face of the top of the borehole and the compression deformation of the plug and friction consume more blasting energy, resulting in lower blasting energy efficiency for top initiation. As a result, the overall damage degree of the specimens in the top-initiation group was significantly smaller than that in the inverse-initiation group. Under conditions of inverse initiation, the blasting energy efficiency is greater, causing the specimen to experience greater damage. Therefore, in the engineering practice of rock tunnel cut blasting, to utilize blasting energy effectively and enhance the effects of rock fragmentation, using the inverse-initiation method is recommended. In addition, in three-dimensional(3D) rock blasting, the bottom of the borehole has obvious end effects under the conditions of inverse initiation, and the crack distribution at the bottom of the borehole is trumpet-shaped. The occurrence of an end effect in the 3D linear-charge blasting model experiment is related to the initiation position and the blocking condition.

Frost heaving and crack initiation characteristics of tunnel rock mass in cold regions under low-temperature degradation

Water freezing in rock fractures causes volumetric expansion and fracture development through frost heaving.This study introduces a novel analytical model to investigate how uneven freezing force and surrounding rock pressure influence fracture initiation,based on mass conservation,elasticity,and water-ice phase transition principles.A model for rock fracture initiation considering freezing temperature,uneven freezing expansion,in-situ stress,and lateral pressure was proposed based on fracture mechanics.Equations for stress intensity factors were developed and validated using the phase field method.The effects of rock elastic modulus anisotropy and critical fracture energy density on fracture initiation were also discussed.The results show that the values of KI and KII exhibit an upward trend as the freezing temperature,uneven expansion,in-situ stress,and lateral pressure increase.The uneven freezing expansion has the most significant influence on KI and KII values among these parameters.As the uneven freezing expansion coefficient increases to 0.5,the fracture initiation mode shifts from tensile fracture to shear fracture.As the lateral pressure coefficient increases to 1,the fracture initiation mode shifts from tensile fracture to shear fracture.Rock elastic modulus anisotropy causes fractures to propagate in a clockwise direction,forming a'butterfly'pattern.Critical fracture energy density an isotropy causes counterclockwise deviation in propagation direction,resulting in branching paths and an'H'-shaped pattern.

A hybrid CNN-LSTM model for diagnosing rice nutrient levels at the rice panicle initiation stage

Nitrogen(N)and potassium(K)are two key mineral nutrient elements involved in rice growth.Accurate diagnosis of N and K status is very important for the rational application of fertilizers at a specific rice growth stage.Therefore,we propose a hybrid model for diagnosing rice nutrient levels at the early panicle initiation stage(EPIS),which combines a convolutional neural network(CNN)with an attention mechanism and a long short-term memory network(LSTM).The model was validated on a large set of sequential images collected by an unmanned aerial vehicle(UAV)from rice canopies at different growth stages during a two-year experiment.Compared with VGG16,AlexNet,GoogleNet,DenseNet,and inceptionV3,ResNet101 combined with LSTM obtained the highest average accuracy of 83.81%on the dataset of Huanghuazhan(HHZ,an indica cultivar).When tested on the datasets of HHZ and Xiushui 134(XS134,a japonica rice variety)in 2021,the ResNet101-LSTM model enhanced with the squeeze-and-excitation(SE)block achieved the highest accuracies of 85.38 and 88.38%,respectively.Through the cross-dataset method,the average accuracies on the HHZ and XS134 datasets tested in 2022 were 81.25 and 82.50%,respectively,showing a good generalization.Our proposed model works with the dynamic information of different rice growth stages and can efficiently diagnose different rice nutrient status levels at EPIS,which are helpful for making practical decisions regarding rational fertilization treatments at the panicle initiation stage.

Molecular cloning,characterization and promoter analysis of LbgCWIN1 and its expression profiles in response to exogenous sucrose during in vitro bulblet initiation in lily

Lily(Lilium spp.) is an important ornamental flower, which is mainly propagated by bulbs. Cell wall invertases(CWINs), which catalyze the irreversibly conversion of sucrose into glucose and fructose in the extracellular space, are key enzymes participating in sucrose allocation in higher plants. Previous studies have shown that CWINs play an essential role in bulblet initiation process in bulbous crops, but the underlying molecular mechanism remains unclear. Here, a CWIN gene of Lilium brownii var. giganteum(Lbg) was identified and amplified from genomic DNA. Quantitative RT-PCR assays revealed that the expression level of LbgCWIN1 was highly upregulated exactly when the endogenous starch degraded in non-sucrose medium during in vitro bulblet initiation in Lbg. Phylogenetic relationship, motif, and domain analysis of LbgCWIN1 protein and CWINs in other plant species showed that all sequences of these CWIN proteins were highly conserved. The promoter sequence of LbgCWIN1 possessed a number of alpha-amylase-, phytohormone-, light-and stress-responsive cis-elements. Meanwhile, β-glucuronidase(GUS) assay showed that the 459 bp upstream fragment from the translational start site displayed maximal promoter activity. These results revealed that LbgCWIN1 might function in the process of in vitro bulblet initiation and be in the response to degradation of endogenous starch.

Shock Initiation Experiments with Modeling on a DNAN Based MeltCast Insensitive Explosive

2,4-dinitroanisole(DNAN)is a good replacement for 2,4,6-trinitrotoluene(TNT)in melt-cast explosives due to its superior insensitivity.With the increasing use of DNAN-based melt-cast explosives,the prediction of reaction violence and hazard assessment of the explosives subjected to shock is of great significance.This study investigated the shock initiation characteristics for a DNAN-based melt-cast explosive,DHFA,using the one-dimensional Lagrangian apparatus.The embedded manganin gauges in the apparatus record the pressure histories at four Lagrangian positions and show that shock-todetonation transition in DHFA needs a high input shock pressure.The experimental data are analyzed to calibrate the Ignition and Growth model.The calibration is performed using an objective function based on both pressure history and the arrival time of shock.Good agreement between experimental and calculated pressure histories indicates the high accuracy of the calibrated parameters with the optimization method.

Timing of Continuous Renal Replacement Therapy Initiation in Sepsis-Associated Acute Kidney Injury: A Comprehensive Review and Future Directions

This review examines the application of continuous renal replacement therapy(CRRT)in patients with sepsis-associated acute kidney injury(S-AKI),with a particular focus on the timing of CRRT initiation.This review addresses the controversy surrounding initiation timing and proposes future research directions.Through a systematic review of recent literature on CRRT for S-AKI,working principles,therapeutic mechanisms,initiation timing of CRRT,and related meta-analyses were summarized.Current studies indicate that the optimal timing for CRRT initiation in S-AKI patients remains inconclusive,with ongoing debate regarding whether early initiation significantly improves patient survival and renal function.This lack of consensus reflects the heterogeneity of the S-AKI patient population and the limitations of existing research methodologies.Future studies should focus on advancing the application of precision medicine in S-AKI and developing individualized treatment strategies by integrating multidimensional information to optimize CRRT utilization and improve patient outcomes.

Fatigue crack initiation and early propagation behavior of 2A97 Al-Li alloy

The fatigue crack initiation and early propagation behavior of 2A97 Al-Li alloy was studied. The smooth specimens were fatigued at room temperature under constant maximum stress control when stress ratio （R） is 0.1 and frequency （f） is 40 Hz. Microstructure observations were examined by optical microscopy, transmission electron microscopy, scanning electron microscopy and electron back scattered diffusion, in order to investigate the relationship between microstructure and fatigue crack initiation and early propagation behavior of 2A97 alloy. The results show that the fatigue cracks are predominantly initiated at inclusions and coarsen secondary phases on the surface of 2A97 alloy. The fatigue crack early propagation behavior of 2A97 alloy is predominantly influenced by the interactions between grain structure and dislocations or persistent slip bands （PSBs）. When the misorientation of two neighbouring grains is close to the orientations of the favorable slip plane within these two grains, high-angle grain boundary severely hinders the PSBs passing through, and thus leads to crack bifurcation and deflection.

Actors of Psychoactive Drug Initiation among Adolescents in Yaoundé-Cameroon

Introduction: Actors of psychoactive drug initiation refer to those who introduce others to psychoactive drug use (initiators) and those who are introduced to psychoactive drugs (users). By identifying their features, better prevention and intervention programs can be developed to reduce psychoactive drug use among adolescents. This article describes the role of actors of psychoactive drug initiation among teenagers in secondary schools in Yaoundé (Cameroon). Methodology: A cross sectional study was carried out in twelve secondary schools in Yaoundé from October 2022 to May 2023. Adolescents from Form four to upper sixth, who assented to participate in the study and received parental consent were included. Data were collected in a structured self-reported questionnaire and analyzed using SPSS 23. Quantitative variables were expressed using means, standard deviations, median and interquartile ranges depending on the distribution of data. Qualitative variables were expressed in the form of frequency and percentages. Results: Drug use was more prevalent among male adolescents (55.3%) from nuclear families (91.4%) who received relatively high pocket money. The main sources of drug exposure were non-family members (49.7%), especially friends outside school. The most frequent place of initiation was snack bars (33.1%). Conclusion: The study revealed the importance of the family, friends and leisure places in the initiation process of drug use in teenagers. Based on these results, parents and school authorities should work together to create a safe and supportive environment that fosters communication, education to prevent drug abuse among adolescents in Yaoundé.

Comprehensive Pattern of Primordium Initiation in Shoot Apex of Wheat

The time course of the initiation of different types of apical primordia on the stem of wheat (Triticum aestivum L.) was investigated to establish a comprehensive pattern of apical primordium development and quantitative dynamic relationships among different primordium initiation. The results showed that the initiation of leaf and bracteal primordia took the S shape, and that of spikelet and floret took the rise stage of parabolic shape in relation to GDD (growing degree days after sowing) in wheat. The bracteal was much like vegetative rather than reproductive organ in terms of the dynamic pattern of primordium initiation. The progress of spikelet and floret primordium initiation could well reflect the characteristics of different genotypes and the impact of different ecological environments on wheat apical development. The integrated model of different primordium initiation in shoot of wheat was an S_shaped curvilinear, and could be divided into three sub_models. The number of leaf primordia was affected by both genotype and environment, while the numbers of bracteal, spikelet and floret primordia were affected mainly by environmental factors. Measured with mean thermochron, the rates of initiation of leaf, bracteal and spikelet primordia in normal planting were the highest among all the sowing date treatments. In contrast to the relationships among leaf, bracteal, spikelet and their initiation duration, the correlation between the number of floret and its initiation duration was highly significant.

Crack initiation stress and strain of jointed rock containing multi-cracks under uniaxial compressive loading: A particle flow code approach

The ratio of crack initiation stress to the uniaxial compressive strength(SCI,B/SUC,B) and the ratio of axial strain at the crack initiation stress to the axial strain at the uniaxial compressive strength(B,UCB,CI,A,A/SSSS) were studied by performing numerical stress analysis on blocks having multi flaws at close spacing's under uniaxial loading using PFC3 D. The following findings are obtained: SCI,B/SUC,B has an average value of about 0.5 with a variability of ± 0.1. This range agrees quite well with the values obtained by former research. For joint inclination angle, β=90°,B,UCB,CI,A,A/SSSS is found to be around 0.48 irrespective of the value of joint continuity factor, k. No particular relation is found betweenB,UCB,CI,A,A/SSSS and β; however, the average B,UCB,CI,A,A/SSSS seems to slightly decrease with increasing k. The variability ofB,UCB,CI,A,A/SSSS is found to increase with k.Based on the cases studied in this work,B,UCB,CI,A,A/SSSS ranges between 0.3 and 0.5. This range is quite close to the range of 0.4to 0.6 obtained for SCI,B/SUC,B. The highest variability of ± 0.12 forB,UCB,CI,A,A/SSSS is obtained for k=0.8. For the remaining k values the variability ofB,UCB,CI,A,A/SSSS can be expressed within ± 0.05. This finding is very similar to the finding obtained for the variability of SCI,B/SUC,B.

Effects of charge size on explosives thermal initiation critical temperature under constrained conditions

In order to study the relationship between charge size and thermal initiation critical temperature of explosive in defined conditions,cook-off test about JH explosive was carried out at a heating rate of 1 ℃/min using self-designed cook-off experiment setup based on thermostatic control technology.Numerical simulation was conducted to study the effects of different charge sizes on thermal initiation critical temperature of explosives with FLUENT software.Experiment results show that there is a thermal initiation critical temperature in cook-off bomb.Simulation results show that when the ratio of the length to diameter of explosives grains is a fixed value,the thermal initiation critical temperature of explosives decreases with the increase of the diameter of explosives grains.When the grains diameter of explosives increase up to a certain value,the influence of charge size on thermal initiation critical temperature tends to be weakened.Charge size has no influence on the ignition point of explosives.The ignition point is always in the center of the grain.

Interacting mechanism and initiation prediction of multiple cracks

The maximum Mode Ⅰ and Mode Ⅱ stress intensity factors(SIFs), KI,kmax(θ) and KII,kmax(θ)(0°<θ<360°), of inclined parallel multi-crack varying with relative positions(including horizontal and vertical spacings) are calculated by the complex function and integration method to analyze their interacting mechanism and determine the strengthening and weakening zone of SIFs. The multi-crack initiation criterion is established based on the ratio of maximum tension-shear SIF to predict crack initiation angle, load, and mechanism. The results show that multi-crack always initiates in Mode Ⅰ and the vertical spacing is better not to be times of half crack-length for crack-arrest, which is in good agreement with test results of the red-sandstone cube specimens with three parallel cracks under uniaxial compression. This can prove the validity of the multi-crack initiation criterion.

Simultaneously measuring initiation toughness of pure mode Ⅰ and mode Ⅱ cracks subjected to impact loads

In order to simultaneously measure the initiation toughness of pure mode Ⅰ and mode Ⅱ cracks in one specimen,a large-size double-cracked concave-convex plate(DCCP)specimen configuration was proposed.Impacting tests were implemented in the drop plate impact device.Strain gauges were employed to measure impact loads and crack initiation time.The corresponding numerical model was established by using the dynamic finite difference program AUTODYN,and the experimental-numerical method and ABAQUS code were utilized to obtain the initial fracture toughness of the crack.Using experiments and numerical research,we concluded that the DCCP specimen is suitable for measuring the initial fracture toughness of pure mode Ⅰ and mode Ⅱ cracks at the same time;the dynamic initiation toughness increases with the increase of loading rate and the crack initiation time decreases with increasing loading rate;the initiation toughness of mode Ⅱ crack is 0.5 times that of mode Ⅰ crack when subjected to the same loading rate.For the pre-crack in the vicinity of the bottom of a sample,when its length increases from 20 to 100 mm,the dynamic initiation toughness of the pure mode Ⅰ crack gradually decreases,and the longer the lower crack length is,the easier the crack would initiate,but the dynamic initiation toughness of pure mode Ⅱ crack varies little.

Impact of orientation of blast initiation on ground vibrations

The blast-induced ground vibrations can be significantly controlled by varying the location and orien-tation of point of interest from blast site.The blast waves generated due to individual holes get super-imposed and resultant peak particle velocity(PPV)generates.With the orientation sequence of holes blasts on site,the superimposition angle of wave changes and hence results in significant variation in resultant PPV.The orientation with respect to the initiation of blasts resulting in lowest PPV needs to be identified for any site.By knowing the PPV contour of vibration waves in mine sites,it is possible to reduce the vibration on the structures by changing the initiation sequence.In this paper,experimental blasts were conducted at two different mine sites and the PPV values were recorded at different ori-entations from the blast site and its initiation sequence.The PPV contours were drawn to identify the orientation with least and highest PPV generation line.It was found that by merely changing the initi-ation sequence of blasts with respect to the sensitive structure or point of interest,the PPV values can be reduced significantly up to 76.9%.

Discussion on “Impact of orientation of blast initiation on ground vibrations” [J Rock Mech Geotech Eng 15 (2022) 255e261]

Recently,Garai et al.(2022)published a paper on the impact of orientation of blast initiation on ground vibrations.However,some of the claims are not supported by the results of the given tests.In Fig.1(see Fig.8 in Garai et al.,2022),there are contours of measured vibration velocities in 4 directions(every 90?)and an incorrect interpretation between them.By placing all measured vibration velocity values(Gerai et al.,2022)at well-defined points on a single figure,it was not possible to precisely determine the type of vibration velocity,such as radial,tangential and vertical vibration velocities,with their different shapes.An incorrect conclusion was also drawn about the direction of the highest vibration velocity.The paper by Garai et al.(2022)measured the vibrational velocity of the medium through which the seismic wave passed,but used the incorrect term shock wave.The shock wave would have destroyed the seismic measuring instruments.A superposition of the vibrational velocity was considered,but not combined with the vibrational frequency of the seismic wave.This paper presents a method for selecting the time delay between successively initiated explosive charges to the measured frequency of the seismic wave,so that the direction of initiation of the explosive charges does not affect the vibration velocity of the ground through which the seismic wave passes.The theoretical and measured shapes and waveforms of radial velocity and tangential velocity in an opencast lignite mine are then presented.Moreover,the conditions for the formation of shock wave,transition wave and seismic waves are presented.

Hydraulic fracture initiation theory for a horizontal well in a coal seam

A series of experiments were pertbrmed to determine rock mechanical parameters related to hydraulic fracturing of coal. The effect of confining pressure and pore pressure on the strength of coal was stt, died. Experimental results show that the coal seam in the study areas has a relatively low elastic modulus, high Poisson＇s ratio, high fragility and is easily broken and compressed. The coal seam is considered as a transversely isotropic medium, since the physical properties in the direction of bedding plane and orthogonal to the bedding plane vary markedly. Based on the generalized plane strain model, stress distribution for an arbitrarily orientated wellbore in the coal seam was determined. In a horizontal well, hydraulic fracturing was lbund to initiate in the coal seam mass due to tensile failure, or from cleats due to shear or tensile failure. For those coal seams with abundant natural cleats, hydraulic fracture initiation can be induced by any of these mechanisms. In this study, hydraulic fracture initiation criteria tbr a horizontal well in a coal seam were established.

An experimental study of fracture initiation mechanisms during hydraulic fracturing

The mechanism of fracture initiation is the basic issue for hydraulic fracture technology. Because of the huge differences in fracture initiation mechanisms for different reservoirs,some successful fracturing techniques applied to porosity reservoirs are ineffectual for fractured reservoirs.Laboratory tests using a process simulation device were performed to confirm the characteristics of fracture initiation and propagation in different reservoirs.The influences of crustal stress field,confining pressure,and natural fractures on the fracture initiation and propagation are discussed.Experimental results demonstrate that stress concentration around the hole would significantly increase the fracture pressure of the rock.At the same time,natural fractures in the borehole wall would eliminate the stress concentration,which leads to a decrease in the fracture initiation pressure.

Effect of main inclusions on crack initiation in bearing steel in the very high cycle fatigue regime

This work aims to investigate the effect of main inclusions on crack initiation in bearing steel in the very high cycle fatigue（VHCF） regime. The size and type of inclusions in the steel were quantitatively analyzed, and VHCF tests were performed. Some fatigue cracks were found to be initiated in the gaps between inclusions（Al2 O3, Mg O-Al2 O3） and the matrix, while other cracks originated from the interior of inclusions（Ti N, Mn S）. To explain the related mechanism, the tessellated stresses between inclusions and the matrix were calculated and compared with the yield stress of the matrix. Results revealed that the inclusions could be classified into two types under VHCF; of these two, only one type could be regarded as holes. Findings in this research provide a better understanding of how inclusions affect the high cycle fatigue properties of bearing steel.

Effect of initiation manners on the scattering characteristics of semi-preformed fragment warhead

The lethality of a semi-preformed fragment warhead is closely related to the expand velocity and spatial distribution of the fragments from ruptured metal casing. The topic of how to improve the utilization of charge of have been drawing great attention from researchers and designer in this filed. In present paper,in order to investigate the influence of charge initiation manners on the scattering characteristics of semi-preformed fragment warhead, the numerical simulations and experimental test are conducted.Firstly, the influence of grid density on numerical results is investigated, and a proper numerical model with relatively high accuracy and effectiveness is determined. Then. numerical simulations of three kinds of different initiation position of a semi-preformed fragment warhead are carried out. An experimental test of the explosion of a semi-preformed fragment warhead is carried out. By comparing and analyzing the numerical results and experimental data, it is found that the initiation manners have great influence on scattering characteristics of semi-preformed fragment warhead. The researcher work of this paper would provide an effective alternative method to optimize the design of warhead.

Initiation of plate tectonics in the Hadean: Eclogitization triggered by the ABEL Bombardment

When plate tectonics began on the Earth has been long debated and here we argue this topic based on the records of Earth-Moon geology and asteroid belt to conclude that the onset of plate tectonics was during the middle Hadean（4.37-4.20 Ga）. The trigger of the initiation of plate tectonics is the ABEL Bombardment, which delivered oceanic and atmospheric components on a completely dry reductive Earth, originally comprised of enstatite chondrite-like materials. Through the accretion of volatiles, shock metamorphism processed with vaporization of both CI chondrite and supracrustal rocks at the bombarded location, and significant recrystallization went through under wet conditions, caused considerable eclogitization in the primordial continents composed of felsic upper crust of 21 km thick anorthosite, and 50 km or even thicker KREEP lower crust. Eclogitization must have yielded a powerful slab-pull force to initiate plate tectonics in the middle Hadean. Another important factor is the size of the bombardment. By creating Pacific Ocean class crater by 1000 km across impactor, rigid plate operating stagnant lid tectonics since the early Hadean was severely destroyed, and oceanic lithosphere was generated to have bi-modal lithosphere on the Earth to enable the operation of plate tectonics.Considering the importance of the ABEL Bombardment event which initiated plate tectonics including the appearance of ocean and atmosphere, we propose that the Hadean Eon can be subdivided into three periods：（1） early Hadean（4.57-4.37 Ga）,（2） middle Hadean（4.37-4.20 Ga）, and（3） late Hadean（4.20-4.00 Ga）.