Harmonics in the Squirrel Cage Induction Motor Analytic Calculation Part III: Influence on the Torque-speed Characteristic

The harmonics that appear in the squirrel cage asynchronous machine have been discussed in great detail in the literature for a long time. However, the systematization of the phenomenon is still pending, so we made an attempt to fill this gap in the previous parts of our study by elaborating formulas for calculation of parasitic torques. It was a general demand among those who work in this field towards the author to verify his formulas with measurements. In the literature, it seems,only one detailed, purposeful series of measurements has been published so far, the purpose of which was to investigate the effect of the number of rotor slots on the torque-speed characteristic curve of the machine. The main goal of this study is to verify the correctness of the formulas by comparing them with the referred series of measurements. Relying on this, the expected synchronous parasitic torques were developed for the frequently used rotor slot numbers-as a design guide for the engineer.Thus, together with our complete table for radial magnetic pull published in our previous work, the designer has all the principles, data and formulas available for the right number of rotor slots for his given machine and for the drive system. This brings this series of papers to an end.

Role of End-ring Configuration in Shaping IE4 Induction Motor Performance

The performance characteristics,particularly the starting performance of direct line-fed induction motors,which are mainly influenced by the design of the rotor,are crucial considerations for end-users.It is quite a challenging issue for motor manufacturers to enhance the starting performance of existing mass-produced motors with minimal modifications and expenses.In this paper,a simple and cost-effective method to improve the starting performance of a commercial squirrel-cage induction motor(SCIM)is proposed.The influence of geometric parameters of the end-ring on the performance characteristics,including starting(locked rotor)torque,pull-up and break down torque,starting current,rotor electric parameters,current density,power losses,and efficiency have been comprehensively investigated.It has been revealed that among the other end-ring design parameters,the ring thickness has a significant effect on the performance characteristics.An optimal end-ring thickness is determined,and its performance characteristics have been compared to those of its initial counterpart.Numeric and parametric analyses have been conducted using a 2D time-stepping finite element method(FEM).The FEM results were validated using experimental measurements obtained from an 11 kW SCIM prototype.

Performance and Safety Improvement of Induction Motors based on Testing and Evaluation Standards

The induction motor,which converts electrical energy into mechanical energy,has been recognized as the cornerstone of industrialization.The rotor of an induction motor can be either a squirrel cage rotor or a wound-type rotor,both existing as magnetless topologies.Three-phase squirrel cage induction motors are frequently utilized in industrial drives because they are dependable,have high starting torque,are selfstarting and affordable.Single-phase induction motors,on the other hand,are commonly used for small loads such as domestic appliances in form of modest fans,pumps and electric power tools.In South Africa,there have been reports of fires and explosions resulting in live and property loss because of induction motors that have not been thoroughly tested or are incorrectly labelled in terms of ratings,electrical safety and performance.The goal of this study is targeted at preventing end-user injuries and failures caused by non-compliant induction motors,by evaluating locally manufactured/imported induction motors based on tests and evaluation from standards(IEC and SANS).The study is conducted using experimental procedures at the Explosion Prevention Technology and Rotating Machines(EPT and RM)laboratory,South African Bureau of Standards(SABS),South Africa.The main finding from the study shows differences in the nameplate characteristics of various induction motors which could have detrimental effects such as production and operational downtime in their end-use industries,at later stages.

Enhanced Fuzzy Logic Control Model and Sliding Mode Based on Field Oriented Control of Induction Motor

In the context of induction motor control, there are various control strategies used to separately control torque and flux. One common approach is known as Field-Oriented Control (FOC). This technique involves transforming the three-phase currents and voltages into a rotating reference frame, commonly referred to as the “dq” frame. In this frame, the torque/speed and flux components are decoupled, allowing for independent control, by doing so, the motor’s speed can be regulated accurately and maintain a constant flux which is crucial to ensure optimal motor performance and efficiency. The research focused on studying and simulating a field-oriented control system using fuzzy control techniques for an induction motor. The aim was to address the issue of parameter variations, particularly the change in rotor resistance during motor operation, which causes the control system to deviate from the desired direction. This deviation implies to an increase in the magnetic flux value, specifically the flux component on the q-axis. By employing fuzzy logic techniques to regulate flux vector’s components in the dq frame, this problem was successfully resolved, ensuring that the magnetic flux value remains within the nominal limits. To enhance the control system’s performance, response speed, and efficiency of the motor, sliding mode controllers were implemented to regulate the current in the inner loop. The simulation results demonstrated the proficiency of the proposed methodology.

Harmonics in the Squirrel Cage Induction Motor Analytic Calculation-Part Ⅰ: Differential Leakage, Attenuation, Asynchronous Parasitic Torques

The magnetic field generated in the air gap of the cage asynchronous machine and the harmonics of the magnetomotive forces creating that magnetic field, as well as the related differential leakage, attenuation, asynchronous parasitic torques have been discussed in great detail in the literature, but always separately, for a long time. However, systematization of the phenomenon still awaits. Therefore, it is worth summarizing the completeness of the phenomena in a single study – with a new approach at the same time-in order to reveal the relationships between them. The role of rotor slot number is emphasized much more than before. An existing, commonly used, but still impractical basic figure has been modified to more clearly demonstrate the response of the rotor for the harmonics of the stator. The need to treat differential leakage, asynchronous parasitic torques and attenuation together will be demonstrated: new formula for asynchronous parasitic torque is derived;the long-used characteristic curves for differential leakage and attenuation used separately so far was merged into one, correct curve in order to provide a correct design guide for the engineers.

Indirect Vector Control of Linear Induction Motors Using Space Vector Pulse Width Modulation

Vector control schemes have recently been used to drive linear induction motors(LIM)in high-performance applications.This trend promotes the development of precise and efficient control schemes for individual motors.This research aims to present a novel framework for speed and thrust force control of LIM using space vector pulse width modulation(SVPWM)inverters.The framework under consideration is developed in four stages.To begin,MATLAB Simulink was used to develop a detailed mathematical and electromechanical dynamicmodel.The research presents a modified SVPWM inverter control scheme.By tuning the proportional-integral(PI)controller with a transfer function,optimized values for the PI controller are derived.All the subsystems mentioned above are integrated to create a robust simulation of the LIM’s precise speed and thrust force control scheme.The reference speed values were chosen to evaluate the performance of the respective system,and the developed system’s response was verified using various data sets.For the low-speed range,a reference value of 10m/s is used,while a reference value of 100 m/s is used for the high-speed range.The speed output response indicates that themotor reached reference speed in amatter of seconds,as the delay time is between 8 and 10 s.The maximum amplitude of thrust achieved is less than 400N,demonstrating the controller’s capability to control a high-speed LIM with minimal thrust ripple.Due to the controlled speed range,the developed system is highly recommended for low-speed and high-speed and heavy-duty traction applications.

Performance Analysis of Optimization Based FOC and DTC Methods for Three Phase Induction Motor

Three-phase induction motors are becoming increasingly utilized in industrialfield due to their better efficiency and simple manufacture.The speed control of an induction motor is essential in a variety of applications,but it is dif-ficult to control.This research analyses the three-phase induction motor’s perfor-mance usingfield-oriented control(FOC)and direct torque control(DTC)techniques.The major aim of this work is to provide a critical evaluation of devel-oping a simple speed controller for induction motors with improving the perfor-mance of Induction Motor(IM).For controlling a motor,different optimization approaches are accessible;in this research,a Fuzzy Logic Controller(FLC)with Fractional Order Darwinian Particle Swarm Optimization(FODPSO)algorithm is presented to control the induction motor.The FOC and DTC are controlled using FODPSO,and their performance is compared to the traditional FOC and DTC technique.Each scheme had its own simulation model,and the results were com-pared using hardware experimental and MATLAB-Simulink.In terms of time domain specifications and torque improvement,the proposed technique surpasses the existing method.

Harmonics in the Squirrel Cage Induction Motor,Analytic Calculation Part Ⅱ:Synchronous Parasitic Torques,Radial Magnetic Forces

The magnetic field generated in the air gap of the cage asynchronous machine and the harmonics of the magnetomotive forces creating that magnetic field,as well as the synchronous parasitic torques,radial magnetic forces have been discussed in great detail in the literature,but always separately,for a long time.However,systematization of the phenomenon still awaits.Therefore,it is worth summarizing the completeness of the phenomena in a single study–with a new approach at the same time-in order to reveal the relationships between them.The role of rotor slot number is emphasized much more than before.New formulas derived for both synchronous torques and radial magnetic forces are used for further investigation.It will be shown that both phenomena in subject must be treated together.Formulas will be provided to take into account attenuation.Design guide will be provided to avoid dangerous rotor slot numbers.It will be shown that the generation of synchronous torques and radial magnetic forces do not depend–in this new approach-on the slot combination,but on the rotor slot number itself.

Improved Clamped Diode Based Z-Source Network for Three Phase Induction Motor

The 3Φinduction motor is a broadly used electric machine in industrial applications,which plays a vital role in industries because of having plenty of beneficial impacts like low cost and easiness but the problems like decrease in motor speed due to load,high consumption of current and high ripple occurrence of ripples have reduced its preferences.The ultimate objective of this study is to control change in motor speed due to load variations.An improved Trans Z Source Inverter(ΓZSI)with a clamping diode is employed to maintain constant input voltage,reduce ripples and voltage overshoot.To operate induction motor at rated speed,different controllers are used.The conventional Proportional-Inte-gral(PI)controller suffers from high settling time and maximum peak overshoot.To overcome these limitations,Fractional Order Proportional Integral Derivative(FOPID)controller optimized by Gray Wolf Optimization(GWO)technique is employed to provide better performance by eliminating maximum peak overshoot pro-blems.The proposed speed controller provides good dynamic response and controls the induction motor more effectively.The complete setup is implemented in MATLAB Simulation to verify the simulation results.The proposed approach provides optimal performance with high torque and speed along with less steady state error.

Speed Identification of Speed Sensorless Linear Induction Motor Based on MRAS

In the linear induction motor control system,the optical grating speed transducer is susceptible to strong magnetic field interference.What's more,it may reduce motor integration and raise device costs.Therefore a speed identification method to replace grating speed transducer is studied in this article.This speed identification method for linear induction motor mainly adopts Model Reference Adaptive Method(Abbreviated as MRAS)and Popov Hyperstability Theory.The research content of this paper can be divided into four parts.First,the mathematical model of the motor based on the model reference adaptive system structure is deduced.Second,the adaptive law of the estimated speed is solved by Popov hyper-stability theory,which ensures the stability of the system.Third,the simulation model of the linear induction motor speed identification control system based on model reference adaptation is built in the MATLAB environment.Finally,the simulation test and analysis are carried out.The simulation results show that the speed identification control system can track the actual speed of the linear induction motor well in the no-load operation and the load operation,and the stability of the system is guaranteed in the full speed range.

LOW COST IMPLEMENTATION OF SPEED SENSORLESS INDUCTION MOTOR CONTROL USING STATOR FLUX ORIENTATION

The control platform of the induction motor （IM） with low costs is developed by using DSP MC56F8013 with a good performance/price rtaio. The control algorithm for the speed sensorless IM is studied based on the stator flux orientation （SFO）. The algorithm structure is simple to be implemented and cannot be influenced by motor parameters, The improved stator flux estimation is used to compensate errors caused by the low pass filter （LPF）. A new speed regulator is designed to ensure the system working with the maximal torque in the transient state. The system simulation and the prototype experiment are made. Results show that the con- trol system has good dynamic and static performance.

Speed Sensorless Vector Control of Induction Motor Based on Reduced Order Extended Kalman Filter

A speed sensorless vector control system of induction motor with estimated rotor speed and rotor flux using a new reduced order extended Kalman filter is proposed. With this method, two rotor flux components are selected as the state variables, and the rotor speed as an estimated parameter is regarded as an augmented state variable. The algorithm with reduced order decreases the computational complexity and makes the proposed estimator feasible to be implemented in real time. The simulation results show high accuracy of the estimation algorithm and good performance of speed control, and verify the usefulness of the proposed algorithm.

INDUCTION MOTOR SPEED CONTROL SYSTEM BASED ON FUZZY NEURAL NETWORK

A fuzzy neural network controller with the teaching controller guidance and parameter regulations for vector-controlled induction motor is proposed. The design procedures of the fuzzy neural controller and the teaching controller are described. The parameters of the membership function are regulated by an on-line learning algorithm. The speed responses of the system under the condition, where the target functions are chosen as I qs and ω, are analyzed. The system responses with the variant of parameter moment of inertial J, viscous coefficients B and torque constant K tare also analyzed. Simulation results show that the control scheme and the controller have the advantages of rapid speed response and good robustness.

Design and Development of the DTC Induction Motor Drive for Electric Vehicle

The design and development of the traction controller for electric vehicle is introduced, which is based on the induction motor. This drive is developed by using a digital signal processor at low cost and carried out with the module design concept of both software and hardware. Nevertheless, a scheme of the sensorless direct torque control is based on the developed hardware, of which the feasibility is tested by a trial program. Additionally, both the interface function of the drive hardware and the feasibility of its software are proved to be good by the trail programs. A test motor can run about 18?r/min by a variable frequency program with the space vector pulse width modulation technology, of which the torque is visible pulsatile. In this presentation, based on the theoretical approach, the sensorless torque control is to be studied and applied to electric vehicles, of which the quick, smooth and stable torque response is emphasized because it quite benefits improving the drive performance of electric vehicles.

Genetic algorithm and particle swarm optimization tuned fuzzy PID controller on direct torque control of dual star induction motor

This study presents analysis, control and comparison of three hybrid approaches for the direct torque control (DTC) of the dual star induction motor (DSIM) drive. Its objective consists of combining three different heuristic optimization techniques including PID-PSO, Fuzzy-PSO and GA-PSO to improve the DSIM speed controlled loop behavior. The GA and PSO algorithms are developed and implemented into MATLAB. As a result, fuzzy-PSO is the most appropriate scheme. The main performance of fuzzy-PSO is reducing high torque ripples, improving rise time and avoiding disturbances that affect the drive performance.

An Intelligent Harmonic Synthesis Technique for Air-Gap Eccentricity Fault Diagnosis in Induction Motors

Induction motors （IMs） are commonly used in various industrial applications. To improve energy con- sumption efficiency, a reliable IM health condition moni- toring system is very useful to detect IM fault at its earliest stage to prevent operation degradation, and malfunction of IMs. An intelligent harmonic synthesis technique is pro- posed in this work to conduct incipient air-gap eccentricity fault detection in IMs. The fault harmonic series are syn- thesized to enhance fault features. Fault related local spectra are processed to derive fault indicators for IM air- gap eccentricity diagnosis. The effectiveness of the pro- posed harmonic synthesis technique is examined experi- mentally by IMs with static air-gap eccentricity and dynamic air-gap eccentricity states under different load conditions. Test results show that the developed harmonic synthesis technique can extract fault features effectively for initial IM air-gap eccentricity fault detection.

A novel induction motor control scheme using IDA-PBC

A new control scheme for induction motors is proposed in the present paper, applying the interconnection and damping assignment-passivity based control （IDA-PBC） method. The scheme is based exclusively on passivity based control, without restricting the input frequency as it is done in field oriented control （FOC）. A port-controlled Hamiltonian （PCH） model of the induction motor is deduced to make the interconnection and damping of energy explicit on the scheme. The proposed controller is validated under computational simulations and experimental tests using an inverter prototype.

Nonlinear Decoupling Control of the Bearingless Induction Motors Based on the Airgap Motor Flux Orientation

The bearingless induction motor, which combines the inductionmotor and magnetic bearing is a strongly coupled complicatednonlinear system; the decoupling control of the electromag- net toqueand readial levitation force is the base of the stable operation ofthe benaringless motor. In this paper, the air-gap motor fluxoriented vector control is proposed to realize the decoupling controlof this nonlinear system even in the transient case based on thelevitation principle. Simulations show the stable suspension and goodperformance of the proposed algorithm.

Fourier and wavelet transformations application to fault detection of induction motor with stator current

Fault detection of an induction motor was carried out using the information of the stator current. After synchronizing the actual data, Fourier and wavelet transformations were adopted in order to obtain the sideband or detail value characteristics under healthy and various faulty operating conditions. The most reliable phase current among the three phase currents was selected using an approach that employs the fuzzy entropy measure. Data were trained with a neural network system, and the fault detection algorithm was verified using the unknown data. Results of the proposed approach based on Fourier and wavelet transformations indicate that the faults can be properly classified into six categories. The training error is 5.3×10-7, and the average test error is 0.103.

Online Detection of Broken Rotor Bar Fault in Induction Motors by Combining Estimation of Signal Parameters via Min-norm Algorithm and Least Square Method

Current research in broken rotor bar （BRB） fault detection in induction motors is primarily focused on a high-frequency resolution analysis of the stator current. Compared with a discrete Fourier transformation, the parametric spectrum estimation technique has a higher frequency accuracy and resolution. However, the existing detection methods based on parametric spectrum estima- tion cannot realize online detection, owing to the large computational cost. To improve the efficiency of BRB fault detection, a new detection method based on the min-norm algorithm and least square estimation is proposed in this paper. First, the stator current is filtered using a band-pass filter and divided into short overlapped data windows. The min-norm algorithm is then applied to determine the fre- quencies of the fundamental and fault characteristic com- ponents with each overlapped data window. Next, based on the frequency values obtained, a model of the fault current signal is constructed. Subsequently, a linear least squares problem solved through singular value decomposition is designed to estimate the amplitudes and phases of the related components. Finally, the proposed method is applied to a simulated current and an actual motor, the results of which indicate that, not only parametric spectrum estimation technique.