Study of Striated Heat Flux on EAST Divertor Plates Induced by LHW Using Infrared Camera

An upgraded infrared （IR） imaging system which provides a wide field of view （FOV） has been installed on the Experimental Advanced Superconducting Tokamak （EAST） to monitor the surface temperatures on plasma facing components. Modified magnetic topology induced by lower hybrid wave （LHW） can lead to the formation of striated heat flux （SHF} on divertor plates which can be clearly observed by IR camera. In this paper, LHW power modulation is applied to analyze the appearance of SHF. It is also demonstrated that deuterium （D） pellet injection and supersonic molecular beam injection （SMBI） can to some extent reduce the heat flux on the outer strike point （OSP）, but enhance the SHF on lower outer plates （LOP） of divertor. This may provide an optional approach to actively control the distribution of heat flux on diveror plates, which can protect materials from long duration high-heat flux.

PRL Near Infrared Camera NICMOS-3

Physical Research Laboratory (PRL), Ahmedabad operates an Astrophysical Observatory equipped with an Infrared Camera NICMOS. 3 (PRLNIC). In this paper characteristics of this camera like dark current, read noise, gain and linearity are discussed. The dark current is found to be quite different in four quadrant varying from 15e /s in one quadrant to 82e /sec in other quadrant. Non linearity is found at both the end of the signal: at low signal level (below 1000ADU) and on the higher end (above 12000ADU) the response becomes non linear. The gain in four quadrant is nearly same.

Characteristics of divertor heat flux distribution with an island divertor configuration on the J-TEXT tokamak

On J-TEXT,the temporal evolution of heat flux distribution on the high-field side(HFS)divertor plate has been measured by an infrared(IR)camera during the plasma operation with an island divertor configuration.In experiments,the island divertor configuration is an edge magnetic island chain structure surrounded by stochastic layers,which can be induced by resonant magnetic perturbations(RMPs).The experimental results show that the heat flux distribution on the HFS target plate depends significantly on the edge magnetic topology.Furthermore,the impact of hydrogen fueling using supersonic molecular beam injection(SMBI)on the divertor heat flux distributions is studied on J-TEXT with an island divertor configuration.It has been observed that power detachment can be achieved when the radiation front approaches the last closed flux surface(LCFS)after each SMBI pulse.This result may provide a method of access for divertor detachment on a fusion device with a three-dimensional(3D)boundary magnetic structure.

Evaluating Infrared Thermal Image’s Color Palettes in Hot Tropical Area

The use of Infrared Thermal Scanners proved to be very useful in lots of applications. Using different color palettes, temperatures can be well-represented in the resulting image. However, most color palettes in hot tropical places like the Philippines are unsuitable since the ambient temperature is almost the same as the scanned object or person. This study evaluates twelve (12) known and used color palettes in the market to determine the most suitable for tropical places using the edge/border tracing algorithms Sobel-Feldman and Laplacian. The result shows that color palettes with the most colors produce more noise, making it difficult to distinguish the object scanned from the background. On the other hand, color palettes with three or fewer contrasting colors produce crisp and more detailed results. This study helps developers and researchers efficiently use color combinations suitable for hot weather for an effective thermal scanning and image representation.

Camera calibration method for an infrared horizon sensor with a large field of view

Inadequate geometric accuracy of cameras is the main constraint to improving the precision of infrared horizon sensors with a large field of view(FOV).An enormous FOV with a blind area in the center greatly limits the accuracy and feasibility of traditional geometric calibration methods.A novel camera calibration method for infrared horizon sensors is presented and validated in this paper.Three infrared targets are used as control points.The camera is mounted on a rotary table.As the table rotates,these control points will be evenly distributed in the entire FOV.Compared with traditional methods that combine a collimator and a rotary table which cannot effectively cover a large FOV and require harsh experimental equipment,this method is easier to implement at a low cost.A corresponding three-step parameter estimation algorithm is proposed to avoid precisely measuring the positions of the camera and the control points.Experiments are implemented with 10 infrared horizon sensors to verify the effectiveness of the calibration method.The results show that the proposed method is highly stable,and that the calibration accuracy is at least 30%higher than those of existing methods.

Device topological thermal management of β-Ga_(2)O_(3) Schottky barrier diodes

The ultra-wide bandgap semiconductor β gallium oxide(β-Ga_(2) O_(3)) gives promise to low conduction loss and high power for electronic devices. However, due to the natural poor thermal conductivity of β-Ga_(2) O_(3), their power devices suffer from serious self-heating effect. To overcome this problem, we emphasize on the effect of device structure on peak temperature in β-Ga_(2) O_(3) Schottky barrier diodes(SBDs) using TCAD simulation and experiment. The SBD topologies including crystal orientation of β-Ga_(2) O_(3), work function of Schottky metal, anode area, and thickness, were simulated in TCAD, showing that the thickness of β-Ga_(2) O_(3) plays a key role in reducing the peak temperature of diodes. Hence, we fabricated β-Ga_(2) O_(3) SBDs with three different thickness epitaxial layers and five different thickness substrates. The surface temperature of the diodes was measured using an infrared thermal imaging camera. The experimental results are consistent with the simulation results. Thus, our results provide a new thermal management strategy for high power β-Ga_(2) O_(3) diode.

Effect of Catch Cup Geometry on 3D Boundary Layer Flow over the Wafer Surface in a Spin Coating

Recently, development of high technology has been required for the formation of thin uniform film in manufacturing processes of semiconductor as the semiconductor instruments become more sophisticated. Spin coating is usually used for spreading photoresist on a wafer surface. However, since rotating speed of the disk is very high in spin coating, the dropped photoresist scarers outward and reattaches on the film surface. A catch cup is set up outside the wafer in spin coating, and scattered photoresist mist is removed from the wafer edge by the exhaust flow generated at the gap between the wafer edge and the catch cup. In the dry process of a spin coating, it is a serious concern that the film thickness increases near the wafer edge in the case of low rotating speed. The purpose of this study is to make clear the effect of the catch cup geometry on the 3D boundary layer flow over the wafer surface and the drying rate of liquid film.