Irregular initial solidification by mold thermal monitoring in the continuous casting of steels:A review

Occasional irregular initial solidification phenomena,including stickers,deep oscillation marks,depressions,and surface cracks of strand shells in continuous casting molds,are important limitations for developing the high-efficiency continuous casting of steels.The application of mold thermal monitoring(MTM) systems,which use thermocouples to detect and respond to temperature variations in molds,has become an effective method to address irregular initial solidification phenomena.Such systems are widely applied in numerous steel companies for sticker breakout prediction.However,monitoring the surface defects of strands remains immature.Hence,indepth research is necessary to utilize the potential advantages and comprehensive monitoring of MTM systems.This paper summarizes what is included in the irregular initial solidification phenomena and systematically reviews the current state of research on these phenomena by the MTM systems.Furthermore,the influences of mold slag behavior on monitoring these phenomena are analyzed.Finally,the remaining problems of the formation mechanisms and investigations of irregular initial solidification phenomena are discussed,and future research directions are proposed.

Dynamic Constraint-Driven Event-Triggered Control of Strict-Feedback Systems Without Max/Min Values on Irregular Constraints

This work proposes an event-triggered adaptive control approach for a class of uncertain nonlinear systems under irregular constraints.Unlike the constraints considered in most existing papers,here the external irregular constraints are considered and a constraints switching mechanism(CSM)is introduced to circumvent the difficulties arising from irregular output constraints.Based on the CSM,a new class of generalized barrier functions are constructed,which allows the control results to be independent of the maximum and minimum values(MMVs)of constraints and thus extends the existing results.Finally,we proposed a novel dynamic constraint-driven event-triggered strategy(DCDETS),under which the stress on signal transmission is reduced greatly and no constraints are violated by making a dynamic trade-off among system state,external constraints,and inter-execution intervals.It is proved that the system output is driven to close to the reference trajectory and the semi-global stability is guaranteed under the proposed control scheme,regardless of the external irregular output constraints.Simulation also verifies the effectiveness and benefits of the proposed method.

Performance and Complexity Trade-Off between Short-Length Regular and Irregular LDPC

In this paper, both the high-complexity near-ML list decoding and the low-complexity belief propagation decoding are tested for some well-known regular and irregular LDPC codes. The complexity and performance trade-off is shown clearly and demonstrated with the paradigm of hybrid decoding. For regular LDPC code, the SNR-threshold performance and error-floor performance could be improved to the optimal level of ML decoding if the decoding complexity is progressively increased, usually corresponding to the near-ML decoding with progressively increased size of list. For irregular LDPC code, the SNR-threshold performance and error-floor performance could only be improved to a bottle-neck even with unlimited decoding complexity. However, with the technique of CRC-aided hybrid decoding, the ML performance could be greatly improved and approached with reasonable complexity thanks to the improved code-weight distribution from the concatenation of CRC and irregular LDPC code. Finally, CRC-aided 5GNR-LDPC code is evaluated and the capacity-approaching capability is shown.

Irregular seismic data reconstruction based on exponential threshold model of POCS method

Irregular seismic data causes problems with multi-trace processing algorithms and degrades processing quality. We introduce the Projection onto Convex Sets （POCS） based image restoration method into the seismic data reconstruction field to interpolate irregularly missing traces. For entire dead traces, we transfer the POCS iteration reconstruction process from the time to frequency domain to save computational cost because forward and reverse Fourier time transforms are not needed. In each iteration, the selection threshold parameter is important for reconstruction efficiency. In this paper, we designed two types of threshold models to reconstruct irregularly missing seismic data. The experimental results show that an exponential threshold can greatly reduce iterations and improve reconstruction efficiency compared to a linear threshold for the same reconstruction result. We also analyze the anti- noise and anti-alias ability of the POCS reconstruction method. Finally, theoretical model tests and real data examples indicate that the proposed method is efficient and applicable.

Variable-coordinate forward modeling of irregular surface based on dual-variable grid

The mapping method is a forward-modeling method that transforms the irregular surface to horizontal by mapping the rectangular grid as curved; moreover, the wave field calculations move from the physical domain to the calculation domain. The mapping method deals with the irregular surface and the low-velocity layer underneath it using a fine grid. For the deeper high-velocity layers, the use of a fine grid causes local oversampling. In addition, when the irregular surface is transformed to horizontal, the flattened interface below the surface is transformed to curved, which produces inaccurate modeling results because of the presence of ladder-like burrs in the simulated seismic wave. Thus, we propose the mapping method based on the dual-variable finite-difference staggered grid. The proposed method uses different size grid spacings in different regions and locally variable time steps to match the size variability of grid spacings. Numerical examples suggest that the proposed method requires less memory storage capacity and improves the computational efficiency compared with forward modeling methods based on the conventional grid.

Ray path of head waves with irregular interfaces

Head waves are usually considered to be the refracted waves propagating along flat interfaces with an underlying higher velocity.However,the path that the rays travel along in media with irregular interfaces is not clear.Here we study the problem by simulation using a new approach of the spectral-element method with some overlapped elements（SEMO） that can accurately evaluate waves traveling along an irregular interface.Consequently,the head waves are separated from interface waves by a time window.Thus,their energy and arrival time changes can be analyzed independently.These analyses demonstrate that,contrary to the case for head waves propagating along a flat interface,there are two mechanisms for head waves traveling along an irregular interface：a refraction mechanism and transmission mechanism.That is,the head waves may be refracted waves propagating along the interface or transmitted waves induced by the waves propagating in the higher-velocity media.Such knowledge will be helpful in constructing a more accurate inversion method,such as head wave travel-time tomography,and in obtaining a more accurate model of subsurface structure which is very important for understanding the formation mechanism of some special areas,such as the Tibetan Plateau.

Research of CRP-based irregular 2D seismic acquisition

Seismic exploration in the mountainous areas of western Chinese is extremely difficult because of the complexity of the surface and subsurface, which results in shooting difficulties, seismic data with low signal-to-noise ratio, and strong interference. The complexity of the subsurface structure leads to strong scattering of the refl ection points; thus, the curved-line acquisition method has been used. However, the actual subsurface structural characteristics have been rarely considered. We propose a design method for irregular acquisition based on common refl ection points（CRP） to avoid difficult-to-shoot areas, while considering the structural characteristics and CRP positions and optimizing the surfacereceiving line position. We arrange the positions of the receiving points to ensure as little dispersion of subsurface CRP as possible to improve the signal-to-noise ratio of the seismic data. We verify the applicability of the method using actual data from a site in Sichuan Basin. The proposed method apparently solves the problem of seismic data acquisition and facilitates seismic exploration in structurally complex areas.

Exact solution and approximate solution of irregular wave radiation stress for non-breaking wave

Wave radiation stress is the main driving force of wave-induced near-shore currents. It is directly related to the hydrodynamic characteristics of near-shore current whether the calculation of wave radiation stress is accurate or not. Irregular waves are more capable of reacting wave motion in the ocean compared to regular waves. Therefore,the calculation of the radiation stress under irregular waves will be more able to reflect the wave driving force in the actual near-shore current. Exact solution and approximate solution of the irregular wave radiation stress are derived in this paper and the two kinds of calculation methods are compared. On the basis of this,the experimental results are used to further verify the calculation of wave energy in the approximate calculation method. The results show that the approximate calculation method of irregular wave radiation stress has a good accuracy under the condition of narrow-band spectrum,which can save a lot of computing time,and thus improve the efficiency of calculation. However,the exact calculation method can more accurately reflect the fluctuation of radiation stress at each moment and each location.

A Breakthrough of Primary Structure in Indeterminate Analysi--Irregular Force Method and Irregular Displacement Method

As the strict limitation of primary structure in traditional force method and displacement method in indeterminate analysis may lead to complicated high-order linear equations, a breakthrough of the limitation, i.e., the application of irregular force method and irregular displacement method, would be introduced in this paper to ease the difficulty of hand computations. By using hyperstatic primary structures and partly chained primary structures, the primary structures of force method and displacement method are reformed, and the order of the system is decreased. The technique is explained through examples. The significance of the new method is summarized.

Multivariate Analyses for Finding Significant Track Irregularities to Generate an Optimal Track Maintenance Schedule

We first discuss the relationship between the optimal track maintenance scheduling model and an efficient detection method for abnormal track irregularities given by the longitudinal level irregularity displacement (LLID). The results of applying the cluster analysis technique to the sampling data showed that maintenance operation is required for approximately 10% of the total lots, and these lots were further classified into three groups according to the degree of maintenance need. To analyze the background factors for detecting abnormal LLID lots, a principal component analysis was performed;the results showed that the first principal component represents LLIDs from the viewpoints of the rail structure, equipment, and operating conditions. Binomial and ordinal logit regression models (LRMs) were used to quantitatively investigate the determinants of abnormal LLIDs. Binomial LRM was used to characterize the abnormal LLIDs, whereas ordinal LRM was used to distinguish the degree of influence of factors that are considered to have a significant impact on LLIDs.

An Irregular Wave Generating Approach Based on naoe-FOAM-SJTU Solver

In this paper,a wave generating approach for long-crest irregular waves in a numerical tank by our in-house solver naoe-FOAM-SJTU is presented.The naoe-FOAM-SJTU solver is developed using an open source tool kit,Open FOAM.Reynolds-averaged Navier？Stokes（RANS） equations are chosen as governing equations and the volume of fluid（VOF） is employed to capture the two phases interface.Incoming wave group is generated by imposing the boundary conditions of the tank inlet.A spectrum based correction procedure is developed to make the measured spectrum approaching to the target spectrum.This procedure can automatically adjust the wave generation signal based on the measured wave elevation by wave height probe in numerical wave tank.After 3 to 4 iterations,the measured spectrum agrees well with the target one.In order to validate this method,several wave spectra are chosen and validated in the numerical wave tank,with comparison between the final measured and target spectra.In order to investigate a practical situation,a modified Wigley hull is placed in the wave tank with incoming irregular waves.The wave-induced heave and pitch motions are treated by Fourier analysis to obtain motion responses,showing good agreements with the measurements.

Mechanism of rock burst caused by fracture of key strata during irregular working face mining and its prevention methods

To study the occurrence mechanism of rock burst during mining the irregular working face,the study took irregular panel 7447 near fault tectonic as an engineering background.The spatial fracture characteristic of overlying strata was analyzed by Winkler elastic foundation beam theory.Furthermore,the influence law of panel width to suspended width and limit breaking span of key strata were also analyzed by thin plate theory.Through micro-seismic monitoring,theoretical analysis,numerical simulation and working resistance of support of field measurement,this study investigated the fracture characteristic of overlying strata and mechanism of rock burst in irregular working face.The results show that the fracture characteristic of overlying strata shows a spatial trapezoid structure,with the main roof being as an undersurface.The fracture form changes from vertical‘‘O-X"type to transverse‘‘O-X"type with the increase of trapezoidal height.From the narrow mining face to the wide mining face,the suspended width of key strata is greater than its limit breaking width,and a strong dynamic load is produced by the fracture of key strata.The numerical simulation and micro-seismic monitoring results show that the initial fracture position of key strata is close to tailgate 7447.Also there is a high static load caused by fault tectonic.The dynamic and static combined load induce rock burst.Accordingly,a cooperative control technology was proposed,which can weaken dynamic load by hard roof directional hydraulic fracture and enhance surrounding rock by supporting system.

Irregular surface of carotid atherosclerotic plaque is associated with ischemic stroke: a magnetic resonance imaging study

Objective To determine the association between the irregularity of carotid plaque surface using multidimensional magnetic resonance imaging(MRI) of ipsilateral acute cerebral infarction(ACI) cases. Methods Patients with recent cerebrovascular symptoms(stroke or transient ischemic attack < 2 weeks) and atherosclerotic plaque in at least one carotid artery were diagnosed by B-mode ultrasound imaging(intima-media thickness ≥ 1.5 mm) and recruited for the present study. Irregular surface was defined when plaque surface was uneven with high and low fluctuation or plaque with surface ulceration. The irregularity of carotid plaque surface was determined on axial or oblique images alone(single-dimension) and on both axial images and oblique images(multidimensions), separately. Univariate and multivariate logistic regression analyses were performed to calculate the odds ratio(OR) and the corresponding 95% CI of the irregular plaque surface in discriminating the presence of ipsilateral ACI. Results A total of 217 included subjects(mean age: 60.7 ± 10.2 years, 149 men) were recruited and 89(41.0%), 88(40.6%) and 118(54.4%) of them exhibited irregular plaque surface on axial, oblique and multidimensional MR images, respectively. The OR of irregularity of the plaque surface was determined by multidimensional MRI to be 5.88(95% CI: 3.16–10.96, P < 0.001) in discriminating the presence of ipsilateral ACI. Following adjustment for clinical confounding factors, this association remained statistically significant(OR = 5.65, 95% CI: 2.53–12.60, P < 0.001). The analysis included further adjustment for the presence of lipid-rich necrotic core, intraplaque hemorrhage and stenosis and the results included that this association also remained statistically significant(OR = 6.08, 95% CI: 2.52–14.68, P < 0.001). Conclusions The irregular plaque surface was determined by multidimensional MRI as an independent indicator for ipsilateral acute cerebral infarction.

Formation Mechanism of "Drag Depressions" and Irregular Boundaries in Intraplate Deformation

Almost all intraplate caprocks experienced strong deformation during the convergence of microplates, and then disintegrated into many secondary geologic units with the special characters, such as irregular boundaries and particular structural assemblages. In order to understand the formation mechanism of these special phenomena, a rheological experiment on the structural scenery of the Tongling area is carried out. The result shows that the primary regular and uniform boundaries of the Tongling area becomes irregular because of the enclosing and confinement of surrounding geological units in the process of 'compression-shearing-rotation-drag'; simultaneously, two specific 'drag depressions' developed at two opposite corners of the block. The former and the later phenomena can be regarded as a typical regional-scale rheological effect and necessary outcome of intraplate deformation respectively.

Experimental Researches on Reflective and Transmitting Performances of Quarter Circular Breakwater Under Regular and Irregular Waves

A series of regular and irregular wave experiments are conducted to study the reflective and transmitting performances of quarter circular breakwater （QCB） in comparison with those of semi-circular breakwater （SCB）. Based on regular wave tests, the reflection and transmission characteristics of QCB are analyzed and a few influencing factors are investigated. Then, the wave energy dissipation as wave passing over the breakwater is discussed based on the hydraulic coefficients of QCB and SCB. In irregular wave experiments, the reflection coefficients of QCB and their spectrums are studied. Finally, the comparisons between the experimental results and numerical simulations for QCB under regular and irregular wave conditions are presented.

Design Optimization of Irregular Cellular Structure for Additive Manufacturing

Irregularcellular structurehas great potential to be considered in light-weight design field. However, the research on optimizing irregular cellular structures has not yet been reporteddue to the difficulties in their modeling technology. Based on the variable density topology opti- mization theory, an efficient method for optimizing the topology of irregular cellular structures fabricated through additive manufacturing processes is proposed. The pro- posed method utilizes tangent circles to automatically generate the main outline of irregular cellular structure. The topological layoutof each cellstructure is optimized using the relative density informationobtained from the proposed modified SIMP method. A mapping relationship between cell structure and relative densityelement is builtto determine the diameter of each cell structure. The results show that the irregular cellular structure can be optimized with the proposed method. The results of simulation and experimental test are similar for irregular cellular structure, which indicate that the maximum deformation value obtained using the modified Solid Isotropic Microstructures with Penalization （SIMP） approach is lower 5.4× 10-5 mm than that using the SIMP approach under the same under the same external load. The proposed research provides the instruction to design the other irregular cellular structure.

Determination of isolation layer thickness for undersea mine based on differential cubature solution to irregular Mindlin plate

The differential cubature solution to the problem of a Mindlin plate lying on the Winkler foundation with two simply supported edges and two clamped edges was derived.Discrete numerical technology and shape functions were used to ensure that the solution is suitable to irregular shaped plates.Then,the mechanical model and the solution were employed to model the protection layer that isolates the mining stopes from sea water in Sanshandao gold mine,which is the first subsea mine of China.Furthermore,thickness optimizations for the protection layers above each stope were conducted based on the maximum principle stress criterion,and the linear relations between the best protection layer thickness and the stope area under different safety factors were regressed to guide the isolation design.The method presented in this work provides a practical way to quickly design the isolation layer thickness in subsea mining.

Galerkin solution of Winkler foundation-based irregular Kirchhoff plate model and its application in crown pillar optimization

Irregular plates are very common structures in engineering,such as ore structures in mining.In this work,the Galerkin solution to the problem of a Kirchhoff plate lying on the Winkler foundation with two edges simply supported and the other two clamped supported is derived.Coordinate transformation technique is used during the solving process so that the solution is suitable to irregular shaped plates.The mechanical model and the solution proposed are then used to model the crown pillars between two adjacent levels in Sanshandao gold mine,which uses backfill method for mining operation.After that,an objective function,which takes security,economic profits and filling effect into consideration,is built to evaluate design proposals.Thickness optimizations for crown pillars are finally conducted in both conditions that the vertical stiffness of the foundation is known and unknown.The procedure presented in the work provides the guidance in thickness designing of complex shaped crown pillars and the preparation of backfill materials,thus to achieve the best balance between security and profits.

A Survey of Evolutionary Algorithms for Multi-Objective Optimization Problems With Irregular Pareto Fronts

Evolutionary algorithms have been shown to be very successful in solving multi-objective optimization problems(MOPs).However,their performance often deteriorates when solving MOPs with irregular Pareto fronts.To remedy this issue,a large body of research has been performed in recent years and many new algorithms have been proposed.This paper provides a comprehensive survey of the research on MOPs with irregular Pareto fronts.We start with a brief introduction to the basic concepts,followed by a summary of the benchmark test problems with irregular problems,an analysis of the causes of the irregularity,and real-world optimization problems with irregular Pareto fronts.Then,a taxonomy of the existing methodologies for handling irregular problems is given and representative algorithms are reviewed with a discussion of their strengths and weaknesses.Finally,open challenges are pointed out and a few promising future directions are suggested.

Effect of Berm Width and Elevation on Irregular Wave Run-Up

This paper discusses the effect of berm width and elevation of composite slope on irregular wave run-up. Based on the data obtained from model tests, the formula and distribution of irregular wave run-up on composite slope are derived. The changing of wind speed, width and elevation of the berm are considered comprehensively. The wave run-up with various exceedance probability can be es-timated utilizing the distribution curves of irregular wave run-up.