Influence of temperature, stress, and grain size on behavior of nano-polycrystalline niobium

Atomic simulations are executed to investigate the creep responses of nano-polycrystalline(NC) niobium established by using the Voronoi algorithm. The effects of varying temperature, applied stress, and grain size(GS) on creep properties and mechanisms are investigated. Notably, the occurrence of tertiary creep is exclusively observed under conditions where the applied stress exceeds 4.5 GPa and the temperature is higher than 1100 K. This phenomenon can be attributed to the significant acceleration of grain boundary and lattice diffusion, driven by the elevated temperature and stress levels. It is found that the strain rate increases with both temperature and stress increasing. However, an interesting trend is observed in which the strain rate decreases as the grain size increases. The stress and temperature are crucial parameters governing the creep behavior. As these factors intensify, the creep mechanism undergoes a sequential transformation: initially from lattice diffusion under low stress and temperature conditions to a mixed mode combining grain boundaries(GBs) and lattice diffusion at moderate stress and mid temperature levels, and ultimately leading to the failure of power-law controlled creep behavior, inclusive of grain boundary recrystallization under high stress and temperature conditions. This comprehensive analysis provides in more detail an understanding of the intricate creep behavior of nano-polycrystalline niobium and its dependence on various physical parameters.

Structural Controls and Predictive Mapping of Tin, Niobium and Tantalum Mineralization Associated with the Mayo Darlé Stanniferous Granitoids;Contributions of Geostatistics

The aim of this study of the spatial dispersion of tin, niobium and tantalum mineralization associated with the Mayo Darlé granitoids was to produce prospecting guides through predictive maps of Sn, Nb and Ta in the region. It was based on a database (in appendix) obtained after analysis of rock samples (greisens and quartz veins) collected in the field, using a portable X-ray fluorescence (XRF) spectrometer. Two approaches were used: 1) structural studies in the field using the directions of veins and fractures 2) the use of variographic maps, an essential element in geostatistics for determining directional anisotropies. A joint synthesis of the modelling results shows that tin, tantalum and niobium mineralization at Mayo Darlé is concentrated along strike intervals N315E to N320E, with mineralization also occurring along strike N35E for high-grade Sn, medium-grade Ta and low-grade Nb. In short, mineral concentrations disperse progressively in space: positively from east to west for tantalum and niobium, and inversely for tin.

Competitive Redox Chemistries in Vanadium Niobium Oxide for Ultrafast and Durable Lithium Storage

Niobium pentoxide(Nb_(2)O_(5))anodes have gained increasing attentions for high-power lithium-ion batteries owing to the outstanding rate capability and high safety.However,Nb2O5 anode suffers poor cycle stability even after modified and the unrevealed mechanisms have restricted the practical applications.Herein,the over-reduction of Nb5+has been demonstrated to be the critical reason for the capacity loss for the first time.Besides,an effective competitive redox strategy has been developed to solve the rapid capacity decay of Nb_(2)O_(5),which can be achieved by the incorporation of vanadium to form a new rutile VNbO_(4)anode.The highly reversible V^(3+)/V^(2+)redox couple in VNbO_(4)can effectively inhibit the over-reduction of Nb^(5+).Besides,the electron migration from V^(3+)to Nb5+can greatly increase the intrinsic electronic conductivity for VNbO4.As a result,VNbO4 anode delivers a high capacity of 206.1 mAh g^(−1)at 0.1 A g^(−1),as well as remarkable cycle performance with a retention of 93.4%after 2000 cycles at 1.0 A g^(−1).In addition,the assembled lithium-ion capacitor demonstrates a high energy density of 44 Wh kg^(−1)at 5.8 kW kg^(−1).In summary,our work provides a new insight into the design of ultra-fast and durable anodes.

Powder mixed electrochemical discharge process for micro machining of C103 niobium alloy

This work demonstrates the viability of the powder-mixed micro-electrochemical discharge machining(PMECDM) process to fabricate micro-holes on C103 niobium-based alloy for high temperature applications.Three processes are involved simultaneously i.e.spark erosion,chemical etching,and abrasive grinding for removal of material while the classical electrochemical discharge machining process involves double actions i.e.spark erosion,and chemical etching.The powder-mixed electrolyte process resulted in rapid material removal along with a better surface finish as compared to the classical microelectrochemical discharge machining(MECDM).Further,the results are optimized through a multiobjective optimization approach and study of the surface topography of the hole wall surface obtained at optimized parameters.In the selected range of experimental parameters,PMECDM shows a higher material removal rate(MRR) and lower surface roughness(R_(a))(MRR:2.8 mg/min and R_(a) of 0.61 μm) as compared to the MECDM process(MRR:2.01 mg/min and corresponding Raof 1.11 μm).A detailed analysis of the results is presented in this paper.

Interfacial structure and mechanical properties of hot-roll bonded joints between titanium alloy and stainless steel using niobium interlayer

The hot-roll bonding was carried out in vacuum between titanium alloy and stainless steel using niobium interlayer. The interfacial structure and mechanical properties were analyzed. The results show that the plasticity of bonded joint is improved significantly. When the bonding temperature is 800 °C or 900 °C, there is not intermetallic layer at the interface between stainless steel and niobium. When the bonding temperature is 1000 °C or 1050 °C, Fe-Nb intermetallic layer forms at the interface. When the bonding temperature is 1050 °C, cracking occurs between stainless steel and intermetallic layer. The maximum strength of -417.5 MPa is obtained at the bonding temperature of 900 °C, the reduction of 25% and the rolling speed of 38 mm/s, and the tensile specimen fractures in the niobium interlayer with plastic fracture characteristics. When the hot-roll bonded transition joints were TIG welded with titanium alloy and stainless steel respectively, the tensile strength of the transition joints after TIG welding is -410.3 MPa, and the specimen fractures in the niobium interlayer.

Segregation and diffusion behavior of niobium in a highly alloyed nickel-base superalloy

The segregation during solidification and high temperature diffusion during homogenization of niobium in a highly alloyed nickel-base superalloy were investigated.Niobium is seriously segregated into the interdendritic regions with segregation coefficient as high as 4.30.Various niobium-enriched phases including Laves phase,δ phase,（γ＋γ＇） eutectic,MC and M6C types of carbides precipitated in the interdendritic regions.The soluble temperature of niobium-enriched phases and the degree of dendritic segregation were determined by differential thermal analysis and homogenization treatments at varied temperatures and times.The calculation of elemental diffusion indicates that the diffusion rate of niobium increases remarkably with the homogenization temperature increasing,so that the annealing time can be effectively reduced.A three-step homogenization treatment technology without incipient melting was established to eliminate the segregation of niobium and to obtain a uniform microstructure.

Preparation of niobium nanoparticles by sodiothermic reduction of Nb_2O_5 in molten salts

Niobium nanoparticles with high purity were prepared by a sodiothermic reduction process using Nb2O5 as the raw material, LiCl, NaCl, KCl and CaCl2 as the diluents and sodium as the reducing reagent. The effects of the different molten salt systems, CaCl2 content, reaction time, excessive sodium and reaction temperature on the characteristics of the obtained niobium powder were discussed. The as-prepared niobium nanoparticles under the optimum experimental conditions were obtained by sodiothermic reduction with 20% excessive sodium in the NaCl-52mol%CaCl2- 2mol%Nb2O5 molten salts at 650 ℃for 6 h, and the molar ratio of the oxygen element in Nb2O5 and the CaCl2 of the molten salts is less than 19.23% at 750 ℃. Moreover, the particle size of niobium nanoparticles is ranged about 40~240 nm with increasing of reaction temperature from 650 to 800 ℃.

Segregation of niobium in laser cladding Inconel 718 superalloy

Inconel 718 superalloy is widely used in the aerospace and turbine industry. Segregation of niobium appears in the laser cladding Inconel 718 superalloy and consequently influences the phase transformation during the rapid solidification. In order to control the microstructure and improve the mechanical properties of the deposited coating, the the influence of solidification conditions on the segregation of niobium and the resultant formation of Nb-rich Laves phase was studied using the microstructure observation and EDS analysis. The results show that the cooling rate has considerable influence on the microstructure of the deposited coating. High cooling rate is beneficial for suppressing the segregation of Nb and reducing the formation of Laves phase, which is believed to be detrimental to the performance of the Inconel 718 alloy.

STUDY ON COMPOSITION IN NIOBIUM ANODE

Niobium capacitor uses electrolytic Nb2O5 as dielectric layer formed on surface of porous niobium anode through electrolytic reaction. Analysis of Scanning Electronics Microscope (SEM) combined with X-ray Photoemission Spectrum(XPS) shows that the formed niobium oxide dielectric consists of not only Nb2O5, but also two kinds of low valence niobium NbO2 and NbO oxide. When using different electrolytic reaction conditions, different valence niobium oxide shows different relative content. The fact provides an important basis for analyzing and improving performances of niobium capacitor.

Effect of Niobium on Isothermal Transformation of Austenite to Ferrite in HSLA Low-Carbon Steel

Using thermomechanical simulation experiment, the kinetics of the isothermal transformation of austenite to ferrite in two HSLA low-carbon steels containing different amounts of niobium was investigated under the conditions of both deformation and undeformation. The results of optical microstructure observation and quantitative metallography analysis showed that the kinetics of the isothermal transformation of austenite to ferrite in lower niobium steel with and without deformation suggests a stage mechanism, wherein there exists a linear relationship between the logarithms of holding time and ferrite volume fraction according to Avrami equation, whereas the isothermal transformation of austenite to ferrite in high niobium steel proceeds via a two stage mechanism according to micrographs, wherein, the nucleation rate of ferrite in the initial stage of transformation is low, and in the second stage, the rate of transformation is high and the transformation of residual austenite to ferrite is rapidly complete. Using carbon extraction replica TEM, niobium carbide precipitation for different holding time was investigated and the results suggested that NbC precipitation and the presence of solute niobium would influence the transformation of austenite to ferrite. The mechanism of the effect of niobium on the isothermal transformation was discussed.

Formation of carbonitride precipitates in hardfacing alloy with niobium addition

Niobium, as the most effective second-phase forming element, was added in the Fe-Crl3-C-N hard- facing alloy to get carbonitride precipitates. Morphology and composition of carbonitride in the hardfacing alloy were studied by optical microscopy, scanning electron microscopy, and electron probe microanalyzer. The ther- modynamics and the effect on the matrix of the formation of carbonitride were also discussed. It was found that niobium carbonitrides are complex Nb（C, N） precipitate distributed on grain boundary and matrix of the hardfacing alloy. Under as-welded condition, primary carbonitride particles were readily precipitated from the hardfacing alloy with large size and morphology as they were formed already during solidification. Under heat treatment condi- tion, a large number of secondary carbonitrides can pre- cipitate out with very fine size and make a great secondary hardening effect on the matrix. As a result, addition of niobium in the hardfacing alloy can prevent the formation of chromium-rich phase on grain boundaries and inter- granular chromium depletion.

Dehydration of xylose to furfural over niobium phosphate catalyst in biphasic solvent system

Phosphoric acid treated niobic acid(NbP)was used for the dehydration of xylose to furfural in biphasic solvent system,which was found to exhibit the best performance among the tested catalysts.The excellent performance of NbP could be explained by the better synergistic cooperation between Bro¨nsted and Lewis acid sites.Moreover,NbP showed good stability and no obvious deactivation or leaching of Nb could be observed after six continuous recycles.

Rare Earths, Niobium and Tantalum Minerals in Bayan Obo Ore Deposit and Discussion on Their Genesis

Bayan Obo ore deposit is endowed with and lie hidden in the Proterozoic strata. The localities and occurrences of the minerals in the ore deposit were described. It is obviously that some minerals are strata minerals and some are post strata minerals. The rare earths, niobium and tantalum minerals are exactly the post strata minerals. In these minerals the hydrothermal metasomatic phenomena distinctly reveal their metallogenic characteristics. According to tectonic movement, magma activity, mineral paragenesis, hydrothermal metasomatism, geological age and lasting time scale of metallogenesis, and some other factors, it is supposed that genesis of rare earths, niobium and tantalum minerals in Bayan Obo ore deposit are closely related with hydrothermal metallogenic solution which is differentiated from silica acid and carbonic acid magma and derived from deep seated source, and then intruded into Proterozoic strata and metasomatized. It is recognized that the metallogenesis of Bayan Obo ore deposit is undergoing a long geological period and many episodes.

Niobium alloying effect in high carbon equivalent grey cast iron

The effect of niobium on the formation of NbC phase and solidification structure in high carbon equivalent grey cast iron was investigated.The experimental results indicated that an increase in the niobium content is favorable to refining the graphite and eutectic cell;and the pearlite lamellar spacing is reduced.Based on the thermodynamic calculation the formation of NbC is prior to the eutectic reaction.The reduction in the pearlite lamellar spacing is mainly attributed to the decrease of eutectic temperature with the addition of niobium.Additionally,properties including hardness and wear resistance were improved after the addition of niobium.

Effect of niobium alloying level on the oxidation behavior of titanium aluminides at 850°C

This work addresses the alloying of titanium aluminides used in aircraft engine applications and automobiles. The oxidation resistance behavior of two titanium aluminides of α2 ＋ γ （Ti3Al ＋ TiAl） and orthorhombic Ti2NbAl, recognized as candidates for high-temperature applications, was investigated by exposure of the alloys for 100 h in air. Thus, oxidation resistance was expressed as the mass gain rate, whereas surface aspects were analyzed using scanning electron microscopy in conjunction with energy-dispersive X-ray spectroscopy, and the type of oxidation products was analyzed by X-ray diffraction and Raman spectroscopy. The orthorhombic Ti2NbAl alloy was embrittled, and pores and microcracks were formed as a result of oxygen diffusion through the external oxide layer formed during thermal oxidation for 100 h.

Microstructures and Mechanical Properties of Si-AI-Mn TRIP Steel with Niobium

Microstructure consisting of ferrite, bainite and retained austenite can be obtained through intercritical annealing and isothermal treatment in bainite transformation region for low silicon TRIP （transformation induced plasticity） steel containing niobium. Effects of strain rate, Nb content and soaking temperature in bainite region on microstructure and mechanical properties of test steels were investigated. It is shown that as strain rate ranges from 10^-2 to 10^-4 s^-1, the volume fraction of transformed martensite from retained austenite, as well as tensile strength, elongation rate and strength-ductility product, increases. When Nb is added, the volume fraction of retained austenite decreases, but tensile strength and yield strength increase. While Nb content reaches 0.014%, the steel exhibits high elongation and combination of strength and ductility. Higher retained austenite volume fraction and good mechanical properties are obtained in the test steels when the soaking temperature in bainite region is 400℃. The maximum values of tensile strength, total elongation rate and strength-ductility product can reach 739 MPa, 38% and 28082 MPa%, respectively.

Electrochemical Behavior of Niobium Electrodeposited 316 Stainless Steel Bipolar Plate for PEMFC in Choline Chloride Based Ionic Liquids

Niobium was electrodeposited on 316 stainless steel bipolar plates of a fuel cell in water and air-stable choline chloride based ionic liquids. The electrochemical corruption property of bipolar plates in simulated PEMFC environment was investigated. It was showed that the plating film was distributed on the surface of 316 stainless steel like isolated islands with height less than 50 nm. The XPS, XRD results showed that a smooth and strong chemical inert film of Nb O and Nb2O5 was formed on the surface of 316 stainless steel. In simulated cathodic condition, the corrosion potential of Nb coated stainless steel was improved by 244 m V, whilst in an anodic condition, it was improved by 105 m V. The current densities for the coated 316 stainless steel were decreased to 2.479 4 μA·cm-2 from 14.810 μA·cm-2 at-0.1 V and to 0.576 μA·cm-2 from 13.417 μA/·cm-2 at 0.6 V, respectively. It was implied that the niobium coating effectively decreased the corrosion rate. The results of the electrochemical tests indicated that the corrosion resistance of stainless steel was greatly improved after coated with niobium.

Niobium Tungsten Oxide in a Green Water‑in‑Salt Electrolyte Enables Ultra‑Stable Aqueous Lithium‑Ion Capacitors

Aqueous hybrid supercapacitors are attracting increasing attention due to their potential low cost,high safety and eco-friendliness.However,the narrow operating potential window of aqueous electrolyte and the lack of suitable negative electrode materials seriously hinder its future applications.Here,we explore high concentrated lithium acetate with high ionic conductivity of 65.5 mS cm−1 as a green“water-in-salt”electrolyte,providing wide voltage window up to 2.8 V.It facilitates the reversible function of niobium tungsten oxide,Nb18W16O93,that otherwise only operations in organic electrolytes previously.The Nb18W16O93 with lithium-ion intercalation pseudocapacitive behavior exhibits excellent rate performance,high areal capacity,and ultra-long cycling stability.An aqueous lithium-ion hybrid capacitor is developed by using Nb18W16O93 as negative electrode combined with graphene as positive electrode in lithium acetate-based“water-in-salt”electrolyte,delivering a high energy density of 41.9 W kg−1,high power density of 20,000 W kg−1 and unexceptionable stability of 50,000 cycles.

Effect of W/Cu composite filler metals on the microstructure and mechanical properties of laser welded pure niobium/304 stainless steel joint

Cracking in a laser weld of niobium to stainless steel occurred due to the formation of brittle,continuously distributed Nb-Fe intermetallic compounds.A crack-free joint,which had a tensile strength of 147 MPa,was obtained by using the W/Cu composite filler metals.To determine the reasons for cracking in the Nb/SS joint and the function of the W/Cu composite filler metals on the improvement of the cracking resistance of the Nb/W/Cu/SS joint,the microstructures of the joints were studied by optical microscopy,scanning electron microscopy and X-ray diffraction.The cracking susceptibilities of the joints were evaluated with microhardness test on the cross section of the Nb/W/Cu/SS joint.The results showed that the Nb/W/Cu/SS joint was characterized by various solid solution.The formation of solid solution reduced the cracking susceptibility of the joint.

Electrochemical behavior of 304 stainless steel with electrodeposited niobium as PEMFC bipolar plates

In order to enhance the corrosion resistance of 304 stainless steel, niobium was electrodeposited on its surface in air- and water-stable ionic liquids. The electrochemical behaviors of bare and niobium-coated 304 stainless steel were evaluated by electrochemical tests in a simulated proton exchange membrane fuel cell （PEMFC） environment. The results showed that niobium could be electrodeposited on the surface of 304 stainless steel from ionic liquids, and a smooth and strong chemical inert compound film was obtained on the surface of 304 stainless steel, which was mainly composed of NbO and Nb2Os. The thin composite film acted as a barrier and remarkably improved the corrosion resistance of 304 stainless steel in the PEMFC environment.