Nonlinear Characteristic Analysis of Gas-Interconnected Quasi-Zero Stiffness Pneumatic Suspension System:A Theoretical and Experimental Study

Because of significantly changed load and complex and variable driving road conditions of commercial vehicles,pneumatic suspension with lower natural frequencies is widely used in commercial vehicle suspension system.How ever,traditional pneumatic suspension system is hardly to respond the greatly changed load of commercial vehicles To address this issue,a new Gas-Interconnected Quasi-Zero Stiffness Pneumatic Suspension(GIQZSPS)is presented in this paper to improve the vibration isolation performance of commercial vehicle suspension systems under frequent load changes.This new structure adds negative stiffness air chambers on traditional pneumatic suspension to reduce the natural frequency of the suspension.It can adapt to different loads and road conditions by adjusting the solenoid valves between the negative stiffness air chambers.Firstly,a nonlinear mechanical model including the dimensionless stiffness characteristic and interconnected pipeline model is derived for GIQZSPS system.By the nonlinear mechanical model of GIQZSPS system,the force transmissibility rate is chosen as the evaluation index to analyze characteristics.Furthermore,a testing bench simulating 1/4 GIQZSPS system is designed,and the testing analysis of the model validation and isolating performance is carried out.The results show that compared to traditional pneumatic suspension,the GIQZSPS designed in the article has a lower natural frequency.And the system can achieve better vibration isolation performance under different load states by switching the solenoid valves between air chambers.

Outcomes and variables that impact pneumatic retinopexies

●AIM:To evaluate the efficacy of pneumatic retinopexy(PR)in patients undergoing PR as primary treatment for rhegmatogenous retinal detachment(RRD)and analyze the factors associated with success and failure in the studied population.●METHODS:A retrospective chart review was done of patients with RRD treated with PR as primary management method treated at New York Eye and Ear Infirmary of Mount Sinai between January 2017 and December 2021.Primary outcome measured success or failure of PR.Secondary outcome measured best corrected visual acuity(BCVA)after PR.A separate risk analysis was done to identify and stratify risks associated with success and failure of PR.●RESULTS:A total of 179 eyes from 179 patients were included for final analysis.The 83 patients(46.37%)achieved anatomical reattachment of the retina after primary PR with no need for additional surgery.The 96 patients(53.63%)had a failed primary PR and required a PPV and 6 of them required pars plana vitrectomy(PPV)with scleral buckle(SB).In total,19 cases(10.61%)were done as temporizing pneumatics,18(94.74%)underwent PPV,and 1(5.26%)did not require further intervention.The visual acuities at postoperative month 1(POM1)for patients who underwent primary PR successfully and for those that underwent PPV after,were 0.58(20/80)and 1.03(20/200)respectively.Patients who met Pneumatic Retinopexy Versus Vitrectomy for the Management of Primary Rhegmatogenous Retinal Detachment Outcomes Randomized Trial(PIVOT)criteria had a statistically significant decreased risk of primary PR failing(hazard ratio 0.29,P=0.00).Majority of missed or new breaks were found superotemporally.●CONCLUSION:PR is a good treatment option for treating RRDs in patients that meet PIVOT criteria and can be conducted as a temporizing measure.PIVOT criteria and fovea on status decrease the risk of PR failure.

Modeling and Simulation of the Characteristics of Pneumatic Cushion Cylinders

The analysis of the characteristics of the cushion process of the pneumatic cushion cylinder is presented, and the nonlinear model of pneumatic cushion cylinders is built in the form of nonlinear differential equations. Besides, through the simulation of the pressure in the cushion chamber, the characteristics of the pneumatic cushion cylinder are obtained, which helps to understand the performance of the pneumatic cushion cylinder and improve or design the better cushion structure.

Study on Quality Improvement of Flue-cured Tobacco by Threshing and Pneumatic Separation

This study was conducted to further classify threshed strips, so as to broaden the usable range of raw material and facilitate the effective utilization of to- bacco resource. During the threshing and redwing process, various process param- eters including the rotating speeds of threshing drums of threshing machioe, draught fans and fling drums were scientifically and rationally set according to the actual quality of the raw material. According to the characteristic that strips with close in- herent quality have basically the same specific gravity and leaf thickness, the strips from each discharge hole were accurately evaluated, and classified, followed by redrying and packaging. The results showed that the threshing and separating pro- cedure could improve the separating effect and precision according to tobacco qual- ity, so as to satisfy the separation and classification requirements for tobacco.

A Kind of PWM Pneumatic Servo Control System——Modulation Methods and Dynamic Responses

Vibrations or dither's are features of the PWM servo control system in their steady outputs. On the grounds of analyses and experiments of a PWM pneumatic servo control system, the paper puts forward four varieties of PWM modulation methods, and concludes on the relationship between dithers and the different methods, and then discusses the influence of friction to the dithers. Results from experiments regarding the dynamic and static responses on the given system support the theories presented.

基于FluidSIM Pneumatics软件的气动及机电一体化设计

气压传动及机电一体化系统设计在现代机械设计中占有很重要的地位。介绍德国FESTO公司开发的FluidSIMPneumatics软件。对该软件的主要技术要求、功能以及气压传动与机电一体化系统的设计方法作了详细的介绍。它为学习者和工程技术人员提供了分析、研究、设计。

Design and Dynamic Model of a Frog-inspired Swimming Robot Powered by Pneumatic Muscles

Pneumatic muscles with similar characteristics to biological muscles have been widely used in robots, and thus are promising drivers for frog inspired robots. How- ever, the application and nonlinearity of the pneumatic system limit the advance. On the basis of the swimming mechanism of the frog, a frog-inspired robot based on pneumatic muscles is developed. To realize the indepen- dent tasks by the robot, a pneumatic system with internal chambers, micro air pump, and valves is implemented. The micro pump is used to maintain the pressure difference between the source and exhaust chambers. The pneumatic muscles are controlled by high-speed switch valves which can reduce the robot cost, volume, and mass. A dynamic model of the pneumatic system is established for the sim- ulation to estimate the system, including the chamber, muscle, and pneumatic circuit models. The robot design is verified by the robot swimming experiments and the dynamic model is verified through the experiments and simulations of the pneumatic system. The simulation results are compared to analyze the functions of the source pressure, internal volume of the muscle, and circuit flow rate which is proved the main factor that limits the response of muscle pressure. The proposed research provides the application of the pneumatic muscles in the frog inspired robot and the pneumatic model to study muscle controller.

Design and control of integrated pneumatic dexterous robot finger

Based on flexible pneumatic actuator(FPA),bending joint and side-sway joint,a new kind of pneumatic dexterous robot finger was developed.The finger is equipped with one five-component force sensor and four contactless magnetic rotary encoders.Mechanical parts and FPAs are integrated,which reduces the overall size of the finger.Driven by FPA directly,the joint output torque is more accurate and the friction and vibration can be effectively reduced.An improved adaptive genetic algorithm(IAGA) was adopted to solve the inverse kinematics problem of the redundant finger.The statics of the finger was analyzed and the relation between fingertip force and joint torque was built.Finally,the finger force/position control principle was introduced.Tracking experiments of fingertip force/position were carried out.The experimental results show that the fingertip position tracking error is within ±1 mm and the fingertip force tracking error is within ±0.4 N.It is also concluded from the theoretical and experimental results that the finger can be controlled and it has a good application prospect.

Development and control of flexible pneumatic wall-climbing robot

A new kind of flexible pneumatic wall-climbing robot,named WALKMAN-I,was proposed. WALKMAN-I is basically composed of a flexible pneumatic actuator (FPA),a flexible pneumatic spherical joint and six suction cups. It has many characteristics of low-cost,lightweight,simple structure and good flexibility. Its operating principle was introduced. Then three basic locomotion modes,which are linear motion,curvilinear motion and crossing the orthogonal planes,were presented. The safety conditions of WALKMAN-I were discussed and built. Finally,the control system was designed and experiments were carried out. Experimental results show that WALKMAN-I is able to climb on the vertical wall surface along a straight line or a curved path,and has the ability of crossing orthogonal planes and obstacles. The maximum rotation angle reaches 90°,the maximum velocity reaches 5 mm/s,and the rotation angle and the moving velocity of WALKMAN-I can be easily controlled.

Real Gas Effects on Charging and Discharging Processes of High Pressure Pneumatics

The high pressure pneumatic system has been applied to special industries. It may cause errors when we analyze high pressure pneumatics under ideal gas assumption. However, the real gas effect on the performances of high pressure pneumatics is seldom investigated. In this paper, the real gas effects on air enthalpy and internal energy are estimated firstly to study the real gas effect on the energy conversion. Under ideal gas assumption, enthalpy and internal energy are solely related to air temperature. The estimation result indicates that the pressure enthalpy and pressure internal energy of real pneumatic air obviously decrease the values of enthalpy and internal energy for high pressure pneumatics, and the values of pressure enthalpy and pressure internal energy are close. Based on the relationship among pressure, enthalpy and internal energy, the real gas effects on charging and discharging processes of high pressure pneumatics are estimated, which indicates that the real gas effect accelerates the temperature and pressure decreasing rates during discharging process, and decelerates their increasing rates during charging process. According to the above analysis, and for the inconvenience in building the simulation model for real gas and the difficulty of measuring the detail thermal capacities of pneumatics, a method to compensate the real gas effect under ideal gas assumption is proposed by modulating the thermal capacity of the pneumatic container in simulation. The experiments of switching expansion reduction （SER） for high pressure pneumatics are used to verify this compensating method. SER includes the discharging process of supply tanks and the charging process of expansion tank. The simulated and experimental results of SER are highly consistent. The proposed compensation method provides a convenient way to obtain more realistic simulation results for high pressure pneumatics.

Flow characteristics and Shannon entropy analysis of dense-phase pneumatic conveying under high pressure

Experiments of dense-phase pneumatic conveying of pulverized coal using nitrogen are carded out in an experimental test facility with the conveying pressure up to 4. 0 MPa and the gas-solid ratio up to 450 kg/m^3. The influences of different conveying differential pressures, coal moisture contents, gas volume flow rates and superficial velocities on the solid-gas ratios are investigated. Shannon entropy analysis of pressure fluctuation time series is developed to reveal the flow characteristics. Through investigation of the distribution of the Shannon entropy under different conditions, the flow stability and the evolutional tendency of the Shannon entropy in different regimes and regime transition processes are discovered, and the relationship between the Shannon entropy and the flow regimes is also established. The results indicate that the solid-gas ratio and the Shannon entropy rise with the increase in conveying differential pressure. The solid-gas ratio and the Shannon entropy reveal preferable regularity with gas volume flow rates. The Shannon entropy is different for different flow regimes, and can be used to identify the flow regimes. Both mass flow rate and the Shannon entropy decrease with the increase in moisture contents. The Shannon entropy analysis is a feasible approach for researching the characteristics of flow regimes, flow stability and flow regime transitions in dense-phase pneumatic conveying under high pressure.

Cross-coupling integral adaptive robust posture control of a pneumatic parallel platform

A pneumatic parallel platform driven by an air cylinder and three circumambient pneumatic muscles was considered. Firstly, a mathematical model of the pneumatic servo system was developed for the MIMO nonlinear model-based controller designed. The pneumatic muscles were controlled by three proportional position valves, and the air cylinder was controlled by a proportional pressure valve. As the forward kinematics of this structure had no analytical solution, the control strategy should be designed in joint space. A cross-coupling integral adaptive robust controller(CCIARC) which combined cross-coupling control strategy and traditional adaptive robust control(ARC) theory was developed by back-stepping method to accomplish trajectory tracking control of the parallel platform. The cross-coupling part of the controller stabilized the length error in joint space as well as the synchronization error, and the adaptive robust control part attenuated the adverse effects of modelling error and disturbance. The force character of the pneumatic muscles was difficult to model precisely, so the on-line recursive least square estimation(RLSE) method was employed to modify the model compensation. The projector mapping method was used to condition the RLSE algorithm to bound the parameters estimated. An integral feedback part was added to the traditional robust function to reduce the negative influence of the slow time-varying characteristic of pneumatic muscles and enhance the ability of trajectory tracking. The stability of the controller designed was proved through Laypunov's theory. Various contrast controllers were designed to testify the newly designed components of the CCIARC. Extensive experiments were conducted to illustrate the performance of the controller.

Simulation on the impact pneumatic cylinder with a reservoir

We proposed a novel impact pneumatic cylinder with a reservoir connected to the inlet chamber so that the pneumatic cylinder can achieve a high speed. A reservoir with high-pressure air enabled the cylirider to achieve considerable＇acceleration when it began to Work. We established a mathematical model to simulate the behaviors of an impact pneumatic cylinder, focusing on the relationships of the maximum piston speed with the air supply pressure and the reservoir volume. The results show that the reservoir .can help significantly enhance the pneumatic system velocity. When the reservoir volume is less than double the cylinder volume, an increase in the reservoir volume is more effective in increasing the maximum piston velocity.

A Survey on Pneumatic Muscle Actuators Modeling

The aim of this article is to provide a survey on the most popular modeling approaches for PMAs （pneumatic muscle actuators）. PMAs are highly non-linear pneumatic actuators where their elongation is proportional to the interval pressure. During the last decade, there has been an increase in the industrial and scientific utilization of PMAs, due to their advantages such as high strength and small weight, while various types of PMAs with different technical characteristics have appeared in the literature. This article will： （a） analyse the PMA＇s operation from a mathematical modeling perspective; （b） present their merits and drawbacks of the most common PMAs; and （c） establish the fundamental basis for developing industrial applications and conducting research in this field.

Study of Web-based integration of pneumatic manipulator and its vision positioning

Pneumatic driven system is widely used in industrial automation, mainly for relatively simple tasks with open-loop control. Because of the pneumatic system’s compressibility and few stop positions, it was considered hard to control in a precise motion control system. With the help of newly developed pneumatic servo control technology, using servo-pneumatic positioning controller now is just as easy as using electro-servo system. This article discusses Web-based servo-pneumatic manipulator control and object recognition and positioning. The authors built a three-degrees-of-freedom (3 DOF) pneumatic manipulator with a servo-pneumatic closed-loop control system and machine vision system in their lab. Web-based tele-operation was a basic ability in this experimental system. After installing a CCD camera, video capture card, and related software developed by the authors, the robot could recognize the user specified object through the Web page and find its position. The remote user could command the robot to move to the position and to grab the object. The critical issues of Web-based control are to integrate hybrid open-architecture mechatronic system through the Web and develop a software language environment characterized by the script. The authors’ experiment showed that pneumatic devices could serve as accurate position control and be controlled through the Web.

PILOT LEAKAGE'S INFLUENCES ON THE PERFORMANCES OF EXTRA HIGH PRESSURE PROPORTIONAL PNEUMATIC VALVE

A mathematic model is built up to analyze the influences of a pilot valve'sleakage on the performances of pneumatic pressure proportional valve, and the performances aresimulated by using MATLAB. The results indicate that using slide pilot valve in the valve system isfeasible, but the leakage's influences can not be neglected, especially it may induce instability ina low output pressure situation. A pilot valve using too large throttle window will cause the valveoscillate. To improve the working condition of pilot valve, a method adopting different widths oftwo throttle window is proposed. According to our simulation, this method balances the pressure dropbetween the two stage throttle ports, and reduces the influences of pilot valve's leakage.

Adaptive Backstepping Slide Mode Control of Pneumatic Position Servo System

With the price decreasing of the pneumatic proportional valve and the high performance micro controller, the simple structure and high tracking performance pneumatic servo system demonstrates more application potential in many fields. However, most existing control methods with high tracking performance need to know the model information and to use pressure sensor. This limits the application of the pneumatic servo system. An adaptive backstepping slide mode control method is proposed for pneumatic position servo system. The proposed method designs adaptive slide mode controller using backstepping design technique. The controller parameter adaptive law is derived from Lyapunov analysis to guarantee the stability of the system. A theorem is testified to show that the state of closed-loop system is uniformly bounded, and the closed-loop system is stable. The advantages of the proposed method include that system dynamic model parameters are not required for the controller design, uncertain parameters bounds are not need, and the bulk and expensive pressure sensor is not needed as well. Experimental performance, as compared with some existing methods. results show that the designed controller can achieve better tracking

Design of wearable hand rehabilitation glove with soft hoop-reinforced pneumatic actuator

Traditional hand rehabilitation gloves usually use electrical motor as actuator with disadvantages of heaviness,bulkiness and less compliance.Recently,the soft pneumatic actuator is demonstrated to be more suitable for hand rehabilitation compared to motor because of its inherent compliance,flexibility and safety.In order to design a wearable glove in request of hand rehabilitation,a soft hoop-reinforced pneumatic actuator is presented.By analyzing the influence of its section shape and geometrical parameters on bending performance,the preferred structure of actuator is achieved based on finite element method.An improved hoop-reinforced actuator is designed after the fabrication and initial measurement,and its mathematical model is built in order to quickly obtain the bending angle response when pressurized.A series of experiment about bending performance are implemented to validate the agreement between the finite element,mathematical and experimental results,and the performance improvement of hoop-reinforced actuator.In addition,the designed hand rehabilitation glove is tested by measuring its output force and actual wearing experience.The output force can reach 2.5 to 3 N when the pressure is 200 kPa.The research results indicate that the designed glove with hoop-reinforced actuator can meet the requirements of hand rehabilitation and has prospective application in hand rehabilitation.

Methods to Evaluate and Measure Power of Pneumatic System and Their Applications

Pneumatic system has been widely used throughout industry, and it consumes more than billions kW h of electricity one year all over the world. So as to improve the efficiency of pneumatic system, its power evaluation as well as measurement methods should be proposed, and their applicability should be validated. In this paper, firstly, power evaluation and measurement methods of pneumatic system were introduced for the first time. Secondly, based on the proposed methods, power distributions in pneumatic system was analyzed. Thirdly, through the analysis on pneumatic efficiencies of typical compressors and pneumatic components, the applicability of the proposed methods were validated. It can be concluded that, first of all, the proposed methods to evaluation and measurement the power of pneumatic system were efficient. Furthermore, the pneumatic power efficiencies of pneumatic system in the air production and cleaning procedure are respectively about 35%–75% and 85%–90%. Moreover, the pneumatic power efficiencies of pneumatic system in the transmission and consumption procedures are about 70%–85% and 10%–35%. And the total pneumatic power efficiency of pneumatic system is about 2%–20%, which varies largely with the system configuration. This paper provides a method to analyze and measure the power of pneumatic system, lay a foundation for the optimization and energy-saving design of pneumatic system.

Fuzzy Torque Control of the Bionic Flexible Manipulator Actuated by Pneumatic Muscle Actuators

A bionic flexible manipulator driven by pneumatic muscle actuator(PMA)can better reflect the flexibility of the mechanism.Current research on PMA mainly focuses on the modeling and control strategy of the pneumatic manipulator system.Compared with traditional electro-hydraulic actuators,the structure of PMA is simple but possesses strong nonlinearity and flexibility,which leads to the difficulty in improving the control accuracy.In this paper,the configuration design of a bionic flexible manipulator is performed by human physiological map,the kinematic model of the mechanism is established,and the dynamics is analyzed by Lagrange method.A fuzzy torque control algorithm is designed based on the computed torque method,where the fuzzy control theory is applied.The hardware experimental system is established.Through the co-simulation contrast test on MATLAB and ADAMS,it is found that the fuzzy torque control algorithm has better tracking performance and higher tracking accuracy than the computed torque method,and is applied to the entity control test.The experimental results show that the fuzzy torque algorithm can better control the trajectory tracking movement of the bionic flexible manipulator.This research proposes a fuzzy torque control algorithm which can compensate the error more effectively,and possesses the preferred trajectory tracking performance.