The Influence of Chemical Admixtures on the Fluidity,Viscosity and Rheological Properties of Ultra-High Performance Concrete

To achieve higher strength and better durability,ultra-high performance concrete(UHPC)typically employs a relatively small water-binder ratio.However,this generally leads to an undesired increase in the paste viscosity.In this study,the effects of liquid and powder polycarboxylate superplasticizers(PCE)on UHPC are compared and critically discussed.Moreover,the following influential factors are considered:air-entraining agents(AE),slump retaining agents(SA),and defoaming agents(DF)and the resulting flow characteristics,mechanical properties,and hydration properties are evaluated assuming UHPC containing 8‰powder PCE(PCE-based UHPC).It is found that the spread diameter of powder PCE is 5%higher than that of liquid PCE.Among the chemical admixtures studied,AEs have the best effect on improving UHPC workability,while DFs have the worst effect.When the addition of AE and SA is 1.25‰and 14.7%of PCE,paste viscosity reduces by 35%and 19%,respectively compared to the paste with only 8‰PCE.A low AE dosage(1.25‰)decreases compressive strength by 4.1%,while SA(8.1%)increases UHPC compressive strength by 9.1%.Both AE and SA significantly delay the UHPC hydration process,reducing the hydration heat release peaks by 76%and 27%,respectively.

Physical-Rheological Properties and Performances of Rejuvenated(Styrene-Butadiene-Styrene)Asphalt with Polymerized-MDI and Aromatic Oil

Traditional asphalt rejuvenators,like aromatic oil(AO),are known to be effective in improving the low-temperature properties and fatigue performances of aged SBS(styrene-butadiene-styrene)modified asphalt(SBSMA)binders and mixtures.However,these rejuvenators inevitably compromise their high-temperature properties and deformation resistances because they dilute asphalt binder but do not fix the damaged structures of aged SBS.In this study,a highly-active chemical called polymerized 4,4-diphenylmethane diisocyanate(PMDI)was used to assist the traditional AO asphalt rejuvenator.The physical and rheological characteristics of rejuvenated SBSMA binders and the moisture-induced damage and rut deformation performances of corresponding mixtures were comparatively evaluated.The results showed that the increasing proportion of AO compromises the hightemperature property and hardness of aged SBSMA binder,and an appropriate amount of PMDI works to compensate such losses;3%rejuvenator at mass ratio of AO:PMDI=70:30 can have a rejuvenated SBSMA binder with a high-temperature performance similar to that of fresh binder,approximately at 71.4°C;the use of AO can help reduce the viscosity of PMDI rejuvenated SBSMA binder for improving its workability;PMDI can help improve the resistance of AO rejuvenated SBSMA binder to deformation,especially at elevated temperatures,through its chemical reactions with aged SBS;moisture induction can enhance the resistance to damage of rejuvenated mixtures containing AO/PMDI or only PMDI;and the rejuvenator with a mass ratio of AO:PMDI=70:30 can lead the rejuvenated mixture to meet the application requirement,with a rut depth of only 2.973 mm,although more PMDI can result in a higher resistance of rejuvenated mixtures to high-temperature deformation.

High Temperature Rheological Performance of Graphene Modified Rubber Asphalt

To elucidate the high temperature rheological capability of graphene modified rubber asphalt,three contents of graphene and crumb rubber were prepared by a combination of mechanical agitation and high speed shearing machine,then used dynamic shear rheological test(DSR)and multiple stress creep recovery(MSCR)tests to evaluate.The hardness and softening point with rotational viscosity of samples raised with the addition of graphene,especially the addition of 0.04%.Dynamic shear rheological test revealedthat the dynamic shear modulus G*,rutting factor G*/Sin δ,and zero shear viscosity(ZSV)of graphene-modified rubber asphalt were greatly influenced along with graphene-increased,on the contrary,phase angle δ which characterize the viscoelastic ratio of asphalt decreased.Multiple stress creep recovery(MSCR)tests showed that the graphene-enhanced rubber asphalt had high-temperature stability through non-recoverable creep compliance(Jnr).Based on these findings,graphene-modified rubber asphalt binders with the addition of 0.04% graphene had good viscoelastic properties as well as high temperature rutting resistance performance.In the meantime,G*/Sin δ,ZSV,and Jnr100,Jnr3200 have good correlation,which can reveal the excellent high-temperature stability performance of asphalt.

Influence of rheological characteristics on the fluidization catastrophe of tailings flows

Limited by mining technology,mineral exploitation can produce large amounts of tailings.Heavy summer rainfall or seasonal freeze-thaw can lead to physical and chemical modification of tailing material in mountainous areas,resulting in fluidized tailings flow and severe disaster losses.Therefore,aiming at the problem of tailings fluidization catastrophe,this paper tried to reveal the rheological mechanism of tailings fluidization transformation by combining rheological tests and theoretical analysis.The results show that the yield stress increases with decreasing temperature,and when the density of debris flow(ρ)is more than 1.9 g/cm~3,this behavior becomes more pronounced as the density increases.The storage modulus decreases by at least two orders of magnitude at the solid-fluid transition under amplitude test sweep.Storage and loss modulus in the linear viscoelastic range and yield stress have an exponential growth relationship with sediment concentration.In addition,a stress constitutive relation and a new exponential law describing the evolution of yield stress required for solid-liquid transformation were proposed,and the relationship is further strengthened through a comprehensive analysis of existing results,which expands the evaluation application of the rheological characteristics of tailings flow.This paper provides a new insight into the rheological properties of tailing and how they occur through solid-liquid transition under different environments,which is beneficial to geological hazard prevention and the ecological remediation of the mining area.

The Research for Surface Properties of Steel Slag Powder and High-Temperature Rheological Properties of Asphalt Mortar

In order to evaluate the feasibility of steel slag powder as filler,the coating properties of steel slag and limestone aggregate were compared by water boiling test,the micro morphology difierences between steel slag powder and mineral powder(limestone powder)were compared by scanning electron microscope(SEM),and the high-temperature rheological properties of asphalt mortar with difierent ratio of filler quality to asphalt quality(F/A)and difierent substitution rates of mineral powder(S/F)were studied by dynamic shear rheological test.The results show that the surface microstructure of steel slag powder is more abundant than that of mineral powder,and the adhesion of steel slag to asphalt is better than that of limestone.At the same temperature,the lower the ratio of S/F is,the greater the rutting factor and complex modulus will be.In addition,the complex modulus and rutting factor of the asphalt mortar increase with the increase of F/A,and the filler type and F/A have a negligible efiect on the phase angle.

Rheological and physicomechanical properties of rod milling sand-based cemented paste backfill modified by sulfonated naphthalene formaldehyde condensate

Rod milling sand(RMS)—a coarse sand aggregate—was recycled for cemented paste backfill(CPB)for the underground mined area at the Jinchuan nickel deposit,named rod milling sand-based cemented paste backfill(RCPB).The adverse effects of coarse particles on the transportation of CPB slurry through pipelines to underground stopes resulting in weakening of the stability of the backfill system are well known.Therefore,sulfonated naphthalene formaldehyde(SNF)condensate was used for the performance improvement of RCPB.The synergistic effect of solid content(SC),lime-to-sand ratio,and SNF dosage on the rheological and physicomechanical properties,including slump,yield stress,bleeding rate,uniaxial compressive strength(UCS),as well as mechanism analysis of RCPB,have been explored.The results indicate that the effect of SNF on RCPB performance is related to the SNF dosage,lime-to-sand ratio,and SC.The slump of fresh RCPB with 0.1wt%-0.5wt%SNF increased by 2.6%-26.2%,whereas the yield stress reduced by 4.1%-50.3%,indicating better workability and improved cohesiveness of the mix.The bleeding rate of fresh RCPB decreased first and then rose with the increase of SNF dosage,and the peak decrease was 67.67%.UCS of RCPB first increased and then decreased with the increase of SNF dosage.At the optimal SNF addition ratio of 0.3wt%,the UCS of RCPB curing for 7,14 and,28 d ages increased by 31.5%,28.4%,and 29.5%,respectively.The beneficial effects of SNF in enhancing the early UCS of RCPB have been corroborated.However,the later UCS increases at a slower rate.The research findings may guide the design and preparation of RCPB with adequate performance for practical applications.

Effect of Synthetic Conditions and Thickener Formulation on the Rheological and Tribological Properties of Polypropylene Grease

Polypropylene(PP)grease holds great potential for special industrial applications.In this study,synthetic conditions,thickener content,and the ratio of two different molecular weight PPs were investigated systematically using a rheometer,scanning electron microscope,X-ray diffraction,Fourier transform infrared spectrometer,oscillating tribometer,and 3D surface profiler measurements.The results showed that suitable synthetic conditions are two quenching cycles,and the synthetic temperature and time is 240℃for 12 h.The rheological analysis showed that thickener content and different proportions of the two PP molecular weights have a significant influence on the rheological properties of PP grease.High molecular weight PP(H-PP)has a stronger thickening ability than low molecular weight PP(L-PP).The higher the amount of H-PP in the fixed thickener content or the higher the thickener content with a specific proportion,the higher the viscoelasticity of PP grease.The tribological performance is related to the rheological properties.The proportion of two different molecular weight PPs in the thickener content should be appropriate;excessive H-PP content leads to lubrication failure.

Rheological and physicochemical characteristics of asphalt mastics incorporating lime kiln dust and dolomite powder as sustainable fillers

The filler-bitumen interaction mechanism is one of the most essential phases for comprehending the asphalt mixture's performance.However,despite numerous studies,in-depth knowledge of filler-bitumen reciprocity at a microscale level is yet to be ascertained.The goal of this research is to gain a better understanding of the fillerbitumen microscale interaction in terms of the synergy and coaction between the physicochemical and rheological performance of mastics due to filler inclusions.The rheological properties of two sustainable mastics,dolomite powder(DP)and lime kiln dust(LKD),together with a neat PEN 60/70 binder,were analysed based on a temperature sweep at elevated temperature conditions.Meanwhile,frequency sweep and multiple stress creep recovery(MSCR)tests were also conducted at pavement serviceability temperature using the dynamic shear rheometer(DSR).Physicochemical tests using a scanning electron microscope(SEM)and energy dispersive X-rays(EDX)were conducted to analyse the impact of parameters such as particle shape,grain size,texture,and chemical compositions.The DSR test results showcased how the incorporation of fillers in asphalt binder considerably improved the performance of the binder in terms of rutting and fatigue.Likewise,its strain and nonrecoverable compliance parameters were substantially reduced at higher filler and binder concentrations.Physical filler attributes of low rigden voids(R.V),high fineness modulus(FM),and high specific surface area(SSA)led to greater interfacial stiffness and elasticity in LKD mastics compared to DP mastics at different loading frequencies and temperature levels.The SEM/EDX results also indicated that the elemental calcium and carbon composition of each filler component,together with its grain morphology,strongly influenced its rheological performance.

Rheological and mechanical properties of wood fiber-PP/PE blend composites

For evaluation of the rheological and mechanical properties of highly filled wood plastic composites （WPCs）, polypropylene/polyethylene （PP/PE） blends were grafted with maleic anhydride （MAH） to enhance the interfacial adhesion between wood fiber and matrix. WPCs were prepared from wood fiber up to 60 wt.% and modified PP/PE was blended by extrusion. The rheological properties were studied by using dynamic measurement. According to the strain sweep test, the linear viscoelastic region of composites in the melt was determined. The result showed that the storage modulus was independent of the strain at low strain region （〈0.1%）. The frequency sweep resuits indicated that all composites exhibited shear thinning behavior, and both the storage modulus and complex viscosity of MAH modified composites were decreased comparing to those unmodified. Flexural properties and impact strength of the prepared WPCs were measured according to the relevant standard specifications. The flexural and impact strength of the manufactured composites significantly increased and reached a maximum when MAH dosage was 1.0 wt%, whereas the flexural modulus after an initial decreased, also increased with MAH dosage. The increase in mechanical properties indicated that the presence of anhydride groups enhanced the interracial adhesion between wood fiber and PP/PE blends.

Creep experiment and rheological model of deep saturated rock

By the methods of uniaxial single-stage loading and graded incremental cyclic loading, the creep experiments were performed on the deep saturated rock from Dongguashan Mine, and the creep curves of saturated rock under different loading stresses were obtained. By comparing with the creep rule of dry rock in the same location, the creep rule of deep saturated rock was analyzed. Based on the united rheological mechanical model, the rheological model of deep saturated rock was recognized, and the parameters of the model were determined. The results show that the creep curves are very smooth under low stress, but the phenomena of wave and catastrophe turn up under high stress, and the bearing capacity of rock is weakening over time. The rheological properties of saturated and dry rocks are very different under tlie condition of deep high stress, especially when unloading, degradation and damage of rock quality is more serious, and the effect of water cannot be neglected. The H--HIN--NJS model （Schofield-Scott-Blair model） was selected to represent the rheology rule of deep saturated rock, and the fitting curves of model agree well with the experiment data, so the selected model is reasonable.

Rheological properties of warm mix asphalt binder by DSR test at medium temperature

The rheological properties including the complex modulus G＊ and the phase angle δof matrix and warm mix asphalt （WMA）binders were measured by using the dynamic shear rheometer （DSR ） test at the medium temperature ranging from 16 to 40 ℃,and the relationships between the fatigue factor G＊ sinδand the matrix binder property,WMA additive and test temperature were established.It is found that G＊ decreases with the increasing temperature while δincreases inversely,and G＊ of the asphalt binder with high WMA additive dosage is large,and δis small.G＊sinδexponentially decreases with the increasing temperature and linearly increases with the increase in additive dosage,and the amplitudes of variation are large at low temperatures and high additive dosages.The effect of WMA additive on the rheological property is more remarkable for the matrix asphalt binder with low G＊.Besides,aging has a great effect on the property of matrix asphalt binder,and a slight effect on the interaction between asphalt and additive.The high additive dosage can increase the fatigue cracking potential of the asphalt binder.

Rheological characteristics of injection molded titanium alloys powder

Ti-6Al-4V alloy powder was taken as raw material. 60%（mass fraction） paraffin, 35%low density polyethylene and 5%stearic acid were employed as binders to prepare injection feedstocks. Capillary rheometer was adopted to determine the rheological parameters and to analyze the rheological properties of the feedstocks at different milling time, powder loading and temperature. It is indicated through the results that the viscosity increases and the value of n decreases with the increase of milling time. The more the powder loading is, the higher the viscosity is. The empirical formula on the relationship between the viscosity and the powder loading is： ηr=η/ηb=A（1-Ф/Фmax）/^- m . The value m is calculated as 0.33. The flow activation energy Ea decreases with the increase of shear rate.

Rheological properties of low consistency TMP from thinning wood of Chinese Fir

The rheological behavior of low consistency thermomechanical pulp of Chinese fir harvested by intermediate thinning was analyzed. The results show that the apparent viscosity of pulp changed along with the beating degree, pulp consistency and shearing velocity. With the increasing of pulp consistency, the apparent viscosity of pulp increased gradually. Beating degree of pulp had an effect on microstructure of pulp. The apparent viscosity of pulp declined as beating degree of pulp increased, and the apparent viscosity of pulp fell along with the shearing velocity increasing. Based on the results, the rheological models are set up. The models showed that the fluid types of the low consistency pulp could be described as pseudoplastics fluids （non-Newtonian fluids）.

Rheological Behavior of Aqueous Solutions of Cationic Guar in Presence of Oppositely Charged Surfactant

The cationic guar （CG） is synthesized and the rheological behavior of aqueous solutions of CG in the presence of sodium dodecyl sulfate （SDS） is studied in detail. The steady viscosity measurements show that the zero shear viscosity enhancement can be almost 3 orders of magnitude as the concentration of SDS increases from 0 to 0.043%. The gel-like formation is observed as the concentration of SDS is greater than 0.016%. The oscillatory rheological measurements of CG solutions in the presence of SDS show that the crossover modulus is almost independent of the concentration of SDS whereas the apparent relaxation time increases swiftly upon increasing the concentration of SDS. The experimental results indicate that the strength rather than the number of the cross-links is greatly affected by SDS molecules. The mechanism concerning the effect of SDS upon the rheology of CG solutions can be coined by the two-stage model. Before the formation of cross-links at the critical concentration, the electrostatic interaction between SDS and cationic site of CG chains plays a key role and the SDS molecules bind to CG chains through the electrostatic interaction. After the formation of cross-links at the concentration greater than the critical concentration, the cooperative hydrophobic interaction become dominant and SDS molecules bind to the cross-links through the hydrophobic interaction. The theological behavior of aqueous solutions of CG in the presence of SDS is chiefly determined by the micelle-like cross-links between CG chains. In fact, the flow activation energy of CG solution, obtained from the temperature dependence of the apparent relaxation time, falls in the range of transferring a hydrophobic tail of SDS from the micelle to an aqueous environment.

High temperature and high pressure rheological properties of high-density water-based drilling fluids for deep wells

To maintain tight control over rheological properties of high-density water-based drilling fluids, it is essential to understand the factors influencing the theology of water-based drilling fluids. This paper examines temperature effects on the rheological properties of two types of high-density water-based drilling fluids （fresh water-based and brine-based） under high temperature and high pressure （HTHP） with a Fann 50SL rheometer. On the basis of the water-based drilling fluid systems formulated in laboratory, this paper mainly describes the influences of different types and concentration of clay, the content of a colloid stabilizer named GHJ-1 and fluid density on the rheological parameters such as viscosity and shear stress. In addition, the effects of aging temperature and aging time of the drilling fluid on these parameters were also examined. Clay content and proportions for different densities of brine-based fluids were recommended to effectively regulate the rheological properties. Four theological models, the Bingham, power law, Casson and H-B models, were employed to fit the rheological parameters. It turns out that the H-B model was the best one to describe the rheological properties of the high-density drilling fluid under HTHP conditions and power law model produced the worst fit. In addition, a new mathematical model that describes the apparent viscosity as a function of temperature and pressure was established and has been applied on site.

Rheological Behavior of Basalt Fiber Reinforced Asphalt Mastic

The characters of basalt fiber are analyzed and compared with commonly used fibers. The rheological behaviors of the basalt fiber reinforced asphalt mastic are investigated by the dynamic shear rheological tests and the repeated creep tests. The results show that basalt fiber has excellent reinforced performances, such as high asphalt absorption ratio, low water absorption ratio, high tensile strength, high elastic modulus and high temperature stability. The rutting factor of the fiber reinforced asphalt mastic is higher than the plain asphalt mastic and the reinforced effects are more remarkable under high temperature. The rheological performances of the asphalt mastic demonstrate a good linear relationship between different temperature and loading frequency. The creep stiffness modulus of the asphalt mastic at different loading time can be expressed by power function. Improved Burgers model is used to represent the rheological behaviors of the asphalt mastic with basalt fiber and the model parameters are estimated.

Rheological property and drying mechanism of thermoresponsive gelcasting of ZnO

To solve the problem of drying gelcast green body, the thermoresponsive gel system which contains macromonomer graft chains was used in gelcasting of ZnO. The effects of the amount and length of graft chains macromonomer PIPAAm, the total amount of organic matters, and the solid loading on the rheological properties of suspensions were investigated, and the drying mechanism of gelcast green body was analyzed. The results show that ZnO suspensions with the gel system still display shear- thinning rheological behavior, but its viscosity increases with increasing the addition amount and relative molecular mass of PIPAAm graft chain, and the total organic matter content. The PIPAAm graft chains inhibit or even eliminate the formation of the ＂dense layer” on the surface of gelcast ZnO green bodies, and accelerate the drying of green bodies. The introduction of PIPAAm graft chains facilitates the shrinkage of the gelcast ZnO green bodies, which is a feasible method to increase the relative density of green bodies.

Integrated identification method of rheological model of sandstone in Sanmenxia bauxite

Based on the uniaxial compression creep experiments conducted on bauxite sandstone obtained from Sanmenxia,typical creep experiment curves were obtained.From the characteristics of strain component of creep curves,the creep strain is composed of instantaneous elastic strain,ε（me）,instantaneous plastic strain,ε（mp）,viscoelastic strain,ε（ce）,and viscoplastic strain,ε（cp）.Based on the characteristics of instantaneous plastic strain,a new element of instantaneous plastic rheology was introduced,instantaneous plastic modulus was defined,and the modified Burgers model was established.Then identification of direct screening method in this model was completed.According to the mechanical properties of rheological elements,one- and three-dimensional creep equations in different stress levels were obtained.One-dimensional model parameters were identified by the method of least squares,and in the process of computation,Gauss-Newton iteration method was applied.Finally,by fitting the experimental curves,the correctness of direct method model was verified,then the examination of posterior exclusive method of the model was accomplished.The results showed that in the improved Burgers models,the rheological characteristics of sandstone are embodied properly,microscopic analysis of creep curves is also achieved,and the correctness of comprehensive identification method of rheological model is verified.

MORPHOLOGICAL MODEL FOR RHEOLOGICAL PROPERTIES OF PLANT CELL SUSPENSION CULTURE SYSTEM

This paper puts forward a physical and mathematical model for the rheological properties of a plant cell suspension culture system.The model can explain why the system is pseudoplastic satisfactorily,thus the rheological properties of the system as the effect of the flow behavior index on plant cell concentration are interpreted correctly and the mechanism of the rheological properties of the system is further understood.Therefore the model can be applied in the technological design and optimum conditions of the system and the reformation,evaluation and scale up of reactors.

Crustal Texture and Rheological Evolution of Tongbai－Dabie Orogenic Belt，China

The crustal texture and rheological evolution of the Tongbai-Dabie orogenic belt are approached from a physical standpoint on the basis of a large body of geological, chronological and geophysical data available in the region. Rheological profiles showing variation of rock Strength with depth in the continental crust are constructed for 1-D crustal structure limited to the Present and Meso-Neoproterozoic structural configurations of the deformed belt, respectively .It is emphasized that the crustal texture and composition have been heterogeneous with the rheological stratification and complicated rheological evolution since the Meso-Neoproterozoic at least. The data appear that the Tongbai - Dabie tectonic belt is a polyphase collisional orogen with evidence for cyclically transition from compressional to extensional regimes and rheological behavior in the levels of the crust.