ISOCHRONOUS STRESS-STRAIN CURVES OF LOW ALLOY STEEL CROSS-WELD-SPECIMEN AT HIGH TEMPERATURE

In this work, a parametric approach is presented and utilized to determine the creep properties of weldments; then the model of creep strain for cross weld specimen is given. On the basis of the experimental results, attempt has been made to establish equations of the isochronous stress-strain for weld joint that can predict the function of loading and service time in use of the creep data of base metal and weld metal.

The Complete Stress-strain Curve of Recycled Aggregate Concrete under Uniaxial Compression Loading

The mechanical performance of recycled aggregate concrete （RAC） is investigated. An experiment on the complete stress-strain curve under uniaxial compression loading of RAC is carried out. The experimental results indicate that the peak stress, peak strain, secant modulus of the peak point and original point increase with the strength grade of RAC enhanced. On the contrary, the residual stress of RAC decreases with the strength grade enhancing, and the failure of RAC is often broken at the interface between the recycled aggregate and the mortar matrix. Finally, the constitutive model of stress-strain model of RAC has been constituted, and the results from the constitutive model of stress-strain meet the experiment results very well.

Numerical simulation of the stress-strain curve and the stress and strain distributions of the titanium-duplex alloy

The stress-strain curve of an α-β Ti-8Mn alloy was measured and then it was calculated with finite element method （FEM） based on the stress-strain curves of the single α and β phase alloys. By comparing the calculated stress-strain curve with the measured one, it can be seen that they fit each other very well. Thus, the FE model built in this work is effective. According to the above mentioned model, the distributions of stress and strain in the α and β phases were simulated. The results show that the stress gradients exist in both α and β phases, and the distributions of stress are inhomogeneous. The stress inside the phase is generally higher than that near the interface. Meanwhile, the stress in the α phase is lower than that in the β phase, whereas the strain in the α phase is higher than that in the β phase.

Charactersitics of Stress-strain Curve of High Strength Steel Fiber Reinforced Concrete under Uniaxial Tension

A whole of 110 specimens divided into 22 groups were tested with varying the volume fraction of steel fibers and the matrix strength of these specimens. The stress-strain behaviors of four types of steel fiber reinforced concrete （SFRC） under uniaxial tension were studied experimentally. When the matrix strength and the fiber content increase, the tensile stress and tensile strain vary differently according to the fiber type. The mechanisms of reinforcing effect for different types of fiber were analyzed and the stress-strain curves of the specimens were plotted. Some experimental factors for stress or strain of SFRC were given. A tensile toughness modulus Re0.5 was introduced to evaluate the toughness characters of SFRC under uniaxial tension. Moreover, the formula of the tensile stress-strain curve of SFRC was regressed. The theoretical curve and the experimental ones fit well, which can be used for references in construction.

Investigation into the stress-strain curves of deformation-induced ferrite transformation in a low carbon steel

A series of tests of deformation-induced ferrite transformation （DIP-T） in a low carbon steel were carried out by the Gleeble-3500 hot simulation machine at a temperature range of Ae3-Ar3. The overall stress-strain curves during DIFT can be divided into three typical types： ＂double-humped＂,＂ single-humped＂ and ＂transitional＂. The peaks exhibited in the curve are involved with deformation-induced transformation which happened in grains or at the grain boundaries. According to the stress-time curve and strain-time curve, strain capacity dramatically postponed the strain-induced transformation, which leads to the start of the transformation right ahead of the finish of deformation and the majority of the ferrite transformation process mainly happened after the deformation. Deformation-induced transformation is a metadynamic transformation process with dynamic nucleation.

MODELING THE STRESS-STRAIN CURVES UNDER DYNAMIC RECRYSTALLIZATION

An analytical model for dynamic recrystallization (DRX) is studied based on the relative grain size model proposed by Sakai and Jonas, and the characteristic flow behaviors under DRX are analyzed and simulated. Introducing the variation of dynamic grain size and the heterogeneous distribution of disolo- cation densities densities under DRX,a simple method for modeling and simulating DRX processes is developed by using Laplace transformation theory. The results derived from the present model agree well with the experimental results in literatures. This simulation can reproduce a number of features in DRX flow behaviors, for example,single and multiple peak flow behaviors followed by a steady state flow, the transition between them, and so on.

Relations of complete creep processes and triaxial stress-strain curves of rock

Based on the results of triaxial compressive creep tests for five kinds of rock under the different stress loading,unloading and cycle-loading-unloading conditions,the creep deformation is not only a function of stress and time,but also it has the corresponding relations to the triaxial stress-strain curves of rock.The deformation properties of soften-strain,harden-strain and ideal plasticity presented by conventional triaxial compressive test curves under the different stress states were utilized,and the creep characteristics,the creep starting stress and the different entire creep process curves of rock were studied systematically according to creep experiment results,and the relations of the triaxial stress-strain curves to the creeping starting stress,the terminating curve,the different creep processes,and the different creep fracture properties were established.The relations presented in this paper were verified partially by the creep experiment results of five types of rock.

MODELLING OF TENSILE STRESS-STRAIN CURVE OF WOVEN FABRICS

A general shape of tensile stress-strain curves of woven fabrics is first recognised by puttingtested and predicted results together.An exponential function with two parameters is then selectedfor the prediction of tensile stress-strain relationship.The predicted results by using the proposedfunction show excellent agreement with experimental data.

The Effect of Unloading Positions and Times on Sheet Metal’s Stress-Strain Curve

The loading-unloading-reloading process could affect the tensile deformation of metals with the combined function of stress relaxation and work hardening, which has been reported in multiple experiments. Nevertheless, the effects of different unloading positions and unloading times have not been investigated. In this study, unloading-reloading tests on three materials (AL6061, HSLA and Q195) were conducted. The stress exhibits a rapid rise momentarily upon reloading and stabilizes afterward while the post stress-strain curve deviates up or down from the monotonic tensile curve. The ductility is enhanced by the unloading-reloading process in general. Different unloading positions and unloading times have different degrees of influence on the stretching of these metals. The effect of loading conditions on a medium manganese steel was further studied. The functions to modify the post stress-strain relationship after unloading-reloading were established.

Comparison of Procedures to Evaluate the Cyclic Stress-Strain Curve from Incremental Step Test

The design of structural components in low-cycle fatigue field often requires the knowledge of the cyclic properties of the material, which are commonly described by the classical relation of Ramberg-Osgood. In order to obtain the cyclic curve using experimental data from incremental step tests, four methodologies are described and critically discussed. Three methods differ in the procedure of evaluation of the elastic modulus, while in the last one the experimental data are interpolated with a single non-linear regression. The various techniques were applied to data obtained from tests carried out on stainless steel specimens, and the resulting differences were analysed and quantified. An average behaviour was evaluated considering the total set of data obtained from experimental tests. The choice of the most suitable method is related to both the strain range of interest and the goal for which the results are used.

Mechanical behaviour of wood compressed in radial direction-part I.New method of determining the yield stress of wood on the stress-strain curve

A test equipment was developed,which allows for real time observation of the deformation behav-ior of wood cellular structure under a compression load applied in radial direction.Compression tests were performed on jack pine(Pinus banksiana)and balsam poplar(Populus balsamifera)spec-imens to explore the relationship between the yield stress and the first failure occurring in wood cell layers during radial compression.The microstructural changes for P.banksiana and P.bal-samifera wood below and above the yield point were analyzed.The study results showed that for P.banksiana the first failure of wood cells occurred at the first earlywood layer,while for P.balsamifera it occurred at the layer with the largest vessels.The first failure of wood cell layer for each species tested was found to correspond to the yield point on the stress-strain curve.A new method of determining the yield stress for wood specimens under radial compression was developed.

Full-Range Compressive Stress-Strain Curves for Cold-Formed 304 Stainless Steel Circular Hollow Sections After Exposure to Vacuum Brazing

With the rapid development of microscale cellular structures, the small-diameter cold-formed welded stainless steel tubes have recently been used for creating the metallic lat- tice topologies with high mechanical properties. In this paper, to obtain the accurate material properties of the circular hollow section （CHS） under pure compression, a series of concentric compression tests are conducted on the millimeter-scale cold-formed 304 stainless steel circu- lar tubular stub columns after exposure to a vacuum brazing process. The tests cover a total of 18 small-diameter stub tubes with measured thickness-to-diameter ratios （t/D） from 0.023 to 0.201. A generalized three-stage nominal stress-strain model is developed for describing the compressive behavior of the post-brazing CHSs over the full strain range. This mechanical model is especially applicable to computer code implementation. Hence, an interactive computer pro- gram is developed to simultaneously optimize three strain hardening exponents （n1, n2, n3） in the expression of the model to produce the stress-strain curve capable of accurately replicating the test data. To further reduce the number of the model and material parameters on which this model depends, this paper also develops five expressions for determining the 2.5% proof stress （ap2）, n2, the ultimate compressive strength （σp3）, n3, and the ultimate plastic strain （p3%） for given experimental values of three basic material parameters （E0, σ0.01, σ0.2）. These expressions are validated to he effective for the CHSs with t/D 〉_ 0.027. The analytically predicted full-range stress-strain curves have generally shown close agreement with the ones obtained experimentally.

Extracting compressive stress-strain curve based on stick-slip shear banding process in bulk metallic glasses

Based on the stick-slip process,an effective method to extract the stress-strain curve directly from the crosshead displacement-load raw data in compression of bulk metallic glasses was proposed.The method was tested in two bulk metallic glass samples with different plasticities and shear band morphologies.The extracted stress-strain curves were found to well resemble the stress-strain curve measured by a laser extensometer.In addition,the extracted curve could resolve fine structures of serrated flow much better than that measured by extensometer,thus facilitating the study of shear banding process.Results obtained by this method made the stick-slip dynamics of shear banding valid,and this method could be employed to obtain the real strain of small-sized metallic glass samples where extensometer cannot be applied.

Inverse design of mechanical metamaterial achieving a prescribedconstitutive curve

Besides exhibiting excellent capabilities such as energy absorption,phase-transforming metamaterials offer a vast design space for achieving nonlinear constitutive relations.This is facilitated by switching between different patterns under deformation.However,the related inverse design problem is quite challenging,due to the lack of appropriate mathematical formulation and the convergence issue in the post-buckling analysis of intermediate designs.In this work,periodic unit cells are explicitly described by the moving morphable voids method and effectively analyzed by eliminating the degrees of freedom in void regions.Furthermore,by exploring the Pareto frontiers between error and cost,an inverse design formulation is proposed for unit cells.This formulation aims to achieve a prescribed constitutive curve and is validated through numerical examples and experimental results.The design approach presented here can be extended to the inverse design of other types of mechanical metamaterials with prescribed nonlinear effective properties.

A comparative study of data-driven battery capacity estimation based on partial charging curves

With its generality and practicality, the combination of partial charging curves and machine learning(ML) for battery capacity estimation has attracted widespread attention. However, a clear classification,fair comparison, and performance rationalization of these methods are lacking, due to the scattered existing studies. To address these issues, we develop 20 capacity estimation methods from three perspectives:charging sequence construction, input forms, and ML models. 22,582 charging curves are generated from 44 cells with different battery chemistry and operating conditions to validate the performance. Through comprehensive and unbiased comparison, the long short-term memory(LSTM) based neural network exhibits the best accuracy and robustness. Across all 6503 tested samples, the mean absolute percentage error(MAPE) for capacity estimation using LSTM is 0.61%, with a maximum error of only 3.94%. Even with the addition of 3 m V voltage noise or the extension of sampling intervals to 60 s, the average MAPE remains below 2%. Furthermore, the charging sequences are provided with physical explanations related to battery degradation to enhance confidence in their application. Recommendations for using other competitive methods are also presented. This work provides valuable insights and guidance for estimating battery capacity based on partial charging curves.

A dynamic soil freezing characteristic curve model for frozen soil

The soil freezing characteristic curve(SFCC)plays a fundamental role in comprehending thermohydraulic behavior and numerical simulation of frozen soil.This study proposes a dynamic model to uniformly express SFCCs amidst varying total water contents throughout the freezing-thawing process.Firstly,a general model is proposed,wherein the unfrozen water content at arbitrary temperature is determined as the lesser of the current total water content and the reference value derived from saturated SFCC.The dynamic performance of this model is verified through test data.Subsequently,in accordance with electric double layer(EDL)theory,the theoretical residual and minimum temperatures in SFCC are calculated to be-14.5℃to-20℃for clay particles and-260℃,respectively.To ensure that the SFCC curve ends at minimum temperature,a correction function is introduced into the general model.Furthermore,a simplified dynamic model is proposed and investigated,necessitating only three parameters inherited from the general model.Additionally,both general and simplified models are evaluated based on a test database and proven to fit the test data exactly across the entire temperature range.Typical recommended parameter values for various types of soils are summarized.Overall,this study provides not only a theoretical basis for most empirical equations but also proposes a new and more general equation to describe the SFCC.

Curve25519点乘算法的高效FPGA实现

为了提高X25519密钥交换算法的运算效率,文章基于现场可编程门阵列(field programmable gate array,FPGA)提出一种高效的曲线Curve25519的点乘设计方案。首先在底层的有限域计算上,针对模约减计算次数多的问题,提出一种基于冗余数的模运算单元,减少了约减次数;同时,所提出的结构可以减少点乘中常系数乘法的运算周期,从而优化了点乘运算通路,提高了并行度,最终减少了运算时间。该文在Xilinx XC7Z020 FPGA上实现了该点乘设计方案,完成一次点乘需要125μs。研究结果表明,与现有的设计相比,所提出的方案具有较低的面积时间积,达到了面积和性能的平衡。

Orientation dependency of shear stress-strain curves in B2-ordered Fe_3Al single crystals deformed in tension at room temperature

B2-ordered Fe3Al single crystals with various orientations were deformed in tension at room temperature in vacuum. The shape of shear stress-strain curves and work hardening rates were found to be strongly dependent on the orientation. The formation of the five different work hardening stages were considered to be related to the number of operative slip systems, the effect of secondary slip systems and the dissociation of the twofold superdislocation. Stage I is an easy glide stage corresponding to single slip. Stage II, with high hardening rate, often corresponds to the existence of conjugate slip systems. Stage III, with relatively low hardening rate, corresponds to the weaker hardening of secondary slip systems. Stage IV, with the highest hardening rate, is not only related to multiple slip but also the dissociation of twofold superdislocations and the moving of superpartials with an antiphase boundary (APB) trap. Stages V, with a negative hardening rate, may be caused by the cross slip of single dissociated superdislocation. The number of stages and the work hardening rate of the same stage were also found to change significantly, when the tensile orientation lies in different orientation regions.

Method for determining the position of landslide slip-surface with a typical inclinometric curves

In the actual monitoring of deep hole displacement,the identification of slip surfaces is primarily based on abrupt changes observed in the inclinometric curve.In conventional identification methods,inclinometric curves exhibiting indications of sliding can be categorized into three types:B-type,D-type,and r-type.The position of the slip surface is typically determined by identifying the depth corresponding to the point of maximum displacement mutation.However,this method is sensitive to the interval of measurement points and the observation scale of the coordinate axes and suffers from unclear sliding surfaces and uncertain values.Based on the variation characteristics of these diagonal curves,we classified the landslide into three components:the sliding body,the sliding interval,and the immobile body.Moreover,three different generalization models were established to analyze the relationships between the curve form and the slip surface location based on different physical indicators such as displacement rate,relative displacement,and acceleration.The results show that the displacement rate curves of an r-type slope exhibit a clustering feature in the sliding interval,and by solving for the depth of discrete points within the step phase,it is possible to determine the location of the slip surface.On the other hand,D-type slopes have inflection points in the relative displacement curve located at the slip surface.The acceleration curves of B-type slopes exhibit clustering characteristics during the sliding interval,while the scattered acceleration data demonstrate wandering characteristics.Consequently,the slip surface location can be revealed by solving the depth corresponding to the maximum acceleration with cubic spline interpolation.The approach proposed in this paper was applied to the monitoring data of a landslide in Yunnan Province,China.The results indicate that our approach can accurately identify the slip surface location and enable computability of its position,thereby enhancing applicability and reliability of the deep-hole displacement monitoring data.

Research into Applicability of Wöhler Curve Method for Low-Cycle Fatigue of Metallic Materials

Recently,a description on a practicability of the Wöhler Curve Method for low-cycle fatigue of metals was given by the author.By the description and the low cycle fatigue test data of 16 MnR steel,it is important to show that,for low cycle fatigue of metals,such a way that a stress-based intensity parameter calculated by the linear-elastic analysis is taken to be a stress intensity parameter,S,to establish a relationship between the stress intensity parameter,S,and the fatigue life,N,is practicable.In this paper,many metallic materials from the literature are given to show that the Wöhler Curve Method is well suitable for low-cycle fatigue analysis of metals.