Airblast evolution initiated by Wangjiayan landslides in the M_(s)8.0 Wenchuan earthquake and its destructive capacity analysis

Airblasts,as one common phenomenon accompanied by rapid movements of landslides or rock/snow avalanches,commonly result in catastrophic damages and are attracting more and more scientific attention.To quantitatively analyze the intensity of airblast initiated by landslides,the Wangjiayan landslide,occurred in the Wenchuan earthquake,is selected here with the landslide propagation and airblast evolution being studied using FLUENT by introducing the Voellmy rheological law.The results reveal that:(1)For the Wangjiayan landslide,its whole travelling duration is only 12 s with its maximum velocity reaching 36 m/s at t=10 s;(2)corresponding to the landslide propagation,the maximum velocity,28 m/s,of the airblast initiated by the landslide also appears at t=10 s with its maximum pressure reaching594.8 Pa,which is equivalent to violent storm;(3)under the attack of airblast,the load suffered by buildings in the airblast zone increases to 1300 Pa at t=9.4 s and sharply decreased to-7000 Pa as the rapid decrease of the velocity of the sliding mass at t=10 s,which is seriously unfavorable for buildings and might be the key reason for the destructive collapse of buildings in the airblast zone of the Wangjiayan landslide.

Identifying drivers of urban landuse changes in the Wenchuan earthquake- affected area by using night-time light data

To learn the process of urban land evolution before and after an earthquake is vital to formulate the urban reconstruction control policies and recovery measures in the earthquake-stricken areas.However,spatiotemporal evolution and its driving factors of urban land in earthquake-prone areas remains limited due to the scarcity of ground observation data.This research,leveraging night-time light remote sensing imagery and land cover data,conducted a comprehensive analysis of the long-term evolution characteristics of urban land in earthquake-prone areas.It introduced methodologies for assessing the socio-economic impact and the primary natural environmental factors driving urban land evolution in these regions.To validate the proposed methods,the 2008 Wenchuan earthquake-affected area in China was selected as a representative study area.The results indicated that the average Digital Number(DN)values in socio-economically impacted areas showed a trend of rising,falling,and then rising again after the earthquake.DN values in three types of damaged areas including Type Ⅱ,Type Ⅲ,and Type Ⅳ exceeded pre-earthquake levels.The analysis of determinative factors influencing urban land evolution revealed that slope and elevation were key elements in controlling urban land expansion before the earthquake,whereas factors such as slope,elevation,lithology,and faults had a stronger influence on urban land expansion after the earthquake.It can be seen that,in view of the differences in the natural conditions of regions for post-disaster reconstruction,the local government need to actively adjust and adapt to urban spatial planning,so as to leverage the scale effect of large-scale inputs of funds,facilities,human resources and other factors after the disaster,thus enhancing resilience and recovery efficiency in response to disaster impacts.

A comparative study of the main factors controlling geohazards induced by 10 strong earthquakes in Western China since the Wenchuan earthquake in 2008

Determining the main controlling factors of earthquake-triggered geohazards is a prerequisite for studying earthquake geohazards and post-disaster emergency response.By studying these factors,the geomorphic and geological factors controlling the nature,condition,and distribution of earthquake-induced geohazards can be analyzed.Such insights facilitate earthquake disaster prediction and emergency response planning.The authors combined field investigations and spatial data analysis to examine geohazards induced by seismic events,examining ten earthquakes including the Wenchuan,Yushu,Lushan events,to elucidate the main control factors of seismic geohazard.The authors observed that seismic geohazard occurrence is usually affected by many factors,among which active nature of the seismogenic fault,seismic peak ground acceleration(PGA),topographic slope and geomorphic height differences,and distance from the fault zone and river system are the most important.Compared with strike-slip earthquakes,thrust earthquakes induce more high-altitude and high-speed remote landslides,which can cause great harm.Slopes of 0°–40°are prone to secondary seismic geohazards,which are mainly concentrated 0–6 km from the river system.Secondary geohazards are not only related to seismogenic fault but also influenced by the associated faults in the earthquake area.The maximum seismic PGA and secondary seismic geohazard number are positively correlated,and the horizontal and vertical ground motions play leading and promoting roles in secondary geohazard formation,respectively.Through the research,the spatial distribution of seismic geohazards is predicted,providing a basis for the formulation of emergency response plans following disasters.

Transient postseismic slip and aftershock triggering:A case study of the 2008 M_W7.9 Wenchuan Earthquake,China

In this study,we investigate how a stress variation generated by a fault that experiences transient postseismic slip(TPS)affects the rate of aftershocks.First,we show that the postseismic slip from Rubin-Ampuero model is a TPS that can occur on the main fault with a velocity-weakening frictional motion,that the resultant slip function is similar to the generalized Jeffreys-Lomnitz creep law,and that the TPS can be explained by a continuous creep process undergoing reloading.Second,we obtain an approximate solution based on the Helmstetter-Shaw seismicity model relating the rate of aftershocks to such TPS.For the Wenchuan sequence,we perform a numerical fitting of the cumulative number of aftershocks using the Modified Omori Law(MOL),the Dieterich model,and the specific TPS model.The fitting curves indicate that the data can be better explained by the TPS model with a B/A ratio of approximately 1.12,where A and B are the parameters in the rate-and state-dependent friction law respectively.Moreover,the p and c that appear in the MOL can be interpreted by the B/A and the critical slip distance,respectively.Because the B/A ratio in the current model is always larger than 1,the model could become a possible candidate to explain aftershock rate commonly decay as a power law with a p-value larger than 1.Finally,the influence of the background seismicity rate r on parameters is studied;the results show that except for the apparent aftershock duration,other parameters are insensitive to r.

Characteristics and Prevention of Secondary Geological Disasters of Wenchuan Earthquake

In the research, secondary geological disasters of Wenchuan earthquake were defined and the consequences were illustrated based on geological disasters, such as collapse, landslide and debris flow, and threats of barrier lakes. In addition, the characteristics of secondary disasters were analyzed, as follows： Rupture of geological faults lays foundation in terms of geological structure; loose solids provide resources of an earthquake; abundant rainfall and large runoffs are driving forces of an earthquake; rainstorm, flood, and long-term high temperature are major inducing factors. Furthermore, suggestions on prevention of secondary disasters were proposed in terms of prevention before, at and after an earthquake. Finally, the scientific and practical significances of secondary disasters were illustrated.

Pupils in Wenchuan Earthquake

A great earthquake broke out in WenChuan. A lot of people were killed, but somany people were rescused by soldiers.Here are stories about three recused pupils.Langzhen, aged three, was rescusedby the soldiers after being buried in ruinsfor 10 hours.

Strong motion observations and recordings from the great Wenchuan Earthquake

The National Strong Motion Observation Network System （NSMONS） of China is briefly introduced in this paper. The NSMONS consists of permanent free-field stations, special observation arrays, mobile observatories and a network management system. During the Wenchuan Earthquake, over 1,400 components of acceleration records were obtained from 460 permanent free-field stations and three arrays for topographical effect and structural response observation in the network system from the main shock, and over 20,000 components of acceleration records from strong aftershocks occurred before August 1, 2008 were also obtained by permanent free-field stations of the NSMONS and 59 mobile instruments quickly deployed after the main shock. The strong motion recordings from the main shock and strong aftershocks are summarized in this paper. In the ground motion recordings, there are over 560 components with peak ground acceleration （PGA） over 10 Gal, the largest being 957.7 Gal. The largest PGA recorded during the aftershock exceeds 300 Gal.

Seismic damage of highway bridges during the 2008 Wenchuan earthquake

Many highway bridges were severely damaged or completely collapsed during the 2008 Wenchuan earthquake. A field investigation was carried out in the strongly affected areas and over 320 bridges were examined. Damage to some representative highway bridges is briefly described and a preliminary analysis of the probable causes of the damage is presented in this paper. The most common damage included shear-flexural failure of the pier columns, expansion joint failure, shear key failure, and girder sliding in the transversal or longitudinal directions due to weak connections between girder and bearings. Lessons learned from this earthquake are described and recommendations related to the design of curved and skewed bridges, design of bearings and devices to prevent girder collapse, and ductility of bridge piers are presented. Suggestions for future seismic design and retrofitting techniques for bridges in moderate to severe earthquake areas are also proposed.

Surface Rupture and Co-seismic Displacement Produced by the Ms 8.0 Wenchuan Earthquake of May ^(12)th,2008,Sichuan,China:Eastwards Growth of the Qinghai-Tibet Plateau

An earthquake of Ms 8 struck Wenchuan County, western Sichuan, China, on May 12^th, 2008 and resulted in long surface ruptures （〉300 km）. The first-hand observations about the surface ruptures produced by the earthquake in the worst-hit areas of Yingxiu, Beichuan and Qingchuan, ascertained that the causative structure of the earthquake was in the central fault zones of the Longmenshan tectonic belt. Average co-seismic vertical displacements along the individual fault of the Yingxiu-Beiehuan rupture zone reach 2.514 m and the cumulative vertical displacements across the central and frontal Longmenshan fault belt is about 5-6 m. The surface rupture strength was reduced from north of Beichuan to Qingchuan County and shows 2-3 m dextral strike-slip component. The Wenchuan thrust-faulting earthquake is a manifestation of eastward growth of the Tibetan Plateau under the action of continuous convergence of the Indian and Eurasian continents.

A preliminary report on the Great Wenchuan Earthquake

The May 12, 2008 Great Wenchuan Earthquake has resulted in more than 68,858 deaths and losses in the hundreds of billions RMB as of May 30, 2008, and these numbers will undoubtedly increase as more information becomes available on the extent of the event. Immediately after the earthquake, the China Earthquake Administration （CEA） responded quickly by sending teams of experts to the affected region, eventually including over 60 staff members from the Institute of Engineering Mechanics （IEM）. This paper reports preliminary information that has been gathered in the first 18 days after the event, covering seismicity, search and rescue efforts, observed ground motions, and damage and loss estimates. The extensive field investigation has revealed a number of valuable findings that could be useful in improving research in earthquake engineering in the future. Once again, this earthquake has shown that the vertical component of ground motion is as significant as horizontal ground motions in the near-source area. Finally, note that as more information is gathered, the numbers reported in this paper will need to be adjusted accordingly.

Damage investigation of girder bridges under the Wenchuan earthquake and corresponding seismic design recommendations

An investigation of girder bridges on National Highway 213 and the Doujiangyan-Wenchuan expressway after the Wenchuan earthquake showed that typical types of damage included： span collapses due to unseating at expansion joints; shear key failure; and damage of the expansion joint due to the slide-induced large relative displacement between the bottom of the girder and the top of the laminated-rubber bearing. This slide, however, can actually act as a form of isolation for the substructure, and as a result, the piers and foundation of most of the bridges on state route 213 suffered minor damage. The exception was the Baihua Bridge, which suffered severe damage. Corresponding seismic design recommendations are presented based on this investigation.

Parameters of Coseismic Reverse- and Oblique-Slip Surface Ruptures of the 2008 Wenchuan Earthquake,Eastern Tibetan Plateau

On May 12th, 2008, the Mw7.9 Wenchuan earthquake ruptured the Beichuan, Pengguan and Xiaoyudong faults simultaneously along the middle segment of the Longmenshan thrust belt at the eastern margin of the Tibetan plateau. Field investigations constrain the surface rupture pattern, length and offsets related to the Wenchuan earthquake. The Beichuan fault has a NE-trending rightlateral reverse rupture with a total length of 240 km. Reassessment yields a maximum vertical offset of 6.5±0.5 m and a maximum right-lateral offset of 4.9±0.5 m for its northern segment, which are the largest offsets found; the maximum vertical offset is 6.2±0.5 m for its southern segment. The Pengguan fault has a NE-trending pure reverse rupture about 72 km long with a maximum vertical offset of about 3.5 m. The Xiaoyudong fault has a NW-striking left-lateral reverse rupture about 7 km long between the Beichuan and Pengguan faults, with a maximum vertical offset of 3.4 m and left-lateral offset of 3.5 m. This pattern of multiple co-seismic surface ruptures is among the most complicated of recent great earthquakes and presents a much larger danger than if they ruptured individually. The rupture length is the longest for reverse faulting events ever reported.

Internal structure of Longmenshan fault zone at Hongkou outcrop,Sichuan,China,that caused the 2008 Wenchuan earthquake

This paper reports the internal structures of the Beichuan fault zone of Longmenshan fault system that caused the 2008 Wenchuan earthquake, at an outcrop in Hongkou, Sichuan province, China. Present work is a part of comprehensive project of Institute of Geology, China Earthquake Administration, trying to understand deformation processes in Longmenshan fault zones and eventually to reproduce Wenchuan earthquake by modeling based on measured mechanical and transport properties. Outcrop studies could be integrated with those performed on samples recovered from fault zone drilling, during the Wenchuan Earthquake Fault Scientific Drilling （WFSD） Project, to understand along-fault and depth variation of fault zone properties. The hanging wall side of the fault zone consists of weakly-foliated, clayey fault gouge of about 1 m in width and of several fault breccia zones of 30-40 m in total width. We could not find any pseudotachylite at this outcrop. Displacement during the Wenchuan earthquake is highly localized within the fault gouge layer along narrower slipping-zones of about 10 to 20 mm in width. This is an important constraint for analyzing thermal pressurization, an important dynamic weakening mechanism of faults. Overlapping patterns of striations on slickenside surface suggest that seismic slip at a given time occurred in even narrower zone of a few to several millimeters, so that localization of deformation must have occurred within a slipping zone during coseismic fault motion. Fault breccia zones are bounded by thin black gouge layers containing amorphous carbon. Fault gouge contains illite and chlorite minerals, but not smectite. Clayey fault gouge next to coseismic slipping zone also contains amorphous carbon and small amounts of graphite. The structural observations and mineralogical data obtained from outcrop exposures of the fault zone of the Wenchuan earthquake can be compared with those obtained from the WFSD-1 and WFSD-2 boreholes, which have been drilled very close to the Hongkou outcrop. The presence of carbon and graphite, observed next to the slipping-zone, may affect the mechanical properties of the fault and also provide useful information about coseismic chemical changes.

Risk Assessment of Highways Affected by Debris Flows in Wenchuan Earthquake Area

Since the Wenchuan earthquake in China on May 12th, 2008, highways in earthquake-affected areas have been frequently interrupted by debris flows. We analyzed the hazard effect modes and damage processes along highways and developed three key indexes, scale of debris flows, deposits on highways and river blockage, to describe quantitatively the highway disasters. By combining the empirical methods and the actual terrain conditions, we proposed new methods to determine the value of hazard indexes. In addition, we used the economic value and resistance of highway as vulnerability assessment indexes, then determined the specific subindexes for the subgrade, bridges and culverts, and developed a way for the quantified vulnerability zoning. Moreover, we proposed the assessment and mapping methods for highway risk. The risk is described into 5 grades： extremely low risk, low risk, middle risk, high risk and extremely high risk. We applied these methods in a case study carried out on provincial highway S3o3 from Yingxiu Town to Wolong Town, in Wenchuan County. Analysis of debris flow risk for the whole highway, showed that the total length of highway in extremely low risk area was 28.26 km, 4.83 km in low risk area, 8.0 km in middle risk area, 3.65 km in high risk area, and 3.06 km in extremely high risk area. The assessment results are consistent with the field survey data which reflected the disaster situation. This risk method can be used objectively to evaluate the debris-flow risk along highways, and is useful for highway reconstruction in mountainous areas suffering from active debris flows.

Spatial Distribution of Large-scale Landslides Induced by the 5.12 Wenchuan Earthquake

The 5.12 Wenchuan Earthquake in 2008 induced hundreds of large-scale landslides. This paper systematically analyzes 112 large-scale landslides (surface area > 50000 m2), which were identified by interpretation of remote sensing imagery and field investigations. The analysis suggests that the distribution of large-scale landslides is affected by the following four factors: (a) distance effect: 80% of studied large-scale landslides are located within a distance of 5 km from the seismic faults. The farther the distance to the faults, the lower the number of large-scale landslides; (b) locked segment effect: the large-scale landslides are mainly located in five concentration zones closely related with the crossing, staggering and transfer sections between one seismic fault section and the next one, as well as the end of the NE fault section. The zone with the highest concentration was the Hongbai-Chaping segment, where a great number of large-scale landslides including the two largest landslides were located. The second highest concentration of large-scale landslides was observed in the Nanba-Donghekou segment at the end of NE fault, where the Donghekou landslide and the Woqian landslide occurred; (c) Hanging wall effect: about 70% of the large-scale landslides occurred on the hanging wall of the seismic faults; and (d) direction effect: in valleys perpendicular to the seismic faults, the density of large-scale landslides on the slopes facing the seismic wave is obviously higher than that on the slopes dipping in the same direction as the direction of propagation of the seismic wave. Meanwhile, it is found that the sliding and moving directions of large-scale landslides are related to the staggering direction of the faults in each section. In Qingchuan County where the main fault activity was horizontal twisting and staggering, a considerable number of landslides showed the feature of sliding and moving in NE direction which coincides with the staggering direction of the seismic faults.

Emergency assessment of seismic landslide susceptibility: a case study of the 2008 Wenchuan earthquake affected area

The 8.0 Mw Wenchuan earthquake triggered widespread and large scale landslides in mountainous regions. An approach was used to map and assess landslide susceptibility in a given area. A numerical rating system was applied to five factors that contribute to slope instability. Factors such as lithology, topography, streams and faults have an important influence as event-controlling factors for landslide susceptibility assessment. A final map is provided to show areas of low, medium, and high landslide susceptibility. Areas identified as having high landslide susceptibility were located in the central, northeastern, and far south regions of the study area. The assessment results will help decision makers to select safe sites for emergency placement of refuges and plan for future reconstruction. The maps may also be used as a basis for landslide risk management in the study area.

Liquefaction macrophenomena in the great Wenchuan earthquake

On May 12, 2008 at 14：28, a catastrophic magnitude M 8.0 earthquake struck the Sichuan Province of China. The epicenter was located at Wenchuan （31.00°N, 103.40°E）. Liquefaction macrophenomena and corresponding destruction was observed throughout a vast area of 500 km long and 200 km wide following the earthquake. This paper illustrates the geographic distribution of the liquefaction and the relationship between liquefaction behavior and seismic intensity, and summarizes the liquefaction macrophenomena, including sandboils and waterspouts, ground subsidence, ground fissures etc., and relevant liquefaction features. A brief summary of the structural damage caused by liquefaction is presented and discussed. Based on comparisons with liquefaction phenomena observed in the 1976 Tangshan and 1975 Haicheng earthquakes, preliminary analyses were performed, which revealed some new features of liquefaction behavior and associated issues arising from this event. The site investigation indicated that the spatial non-uniformity of liquefaction distribution was obvious and most of the liquefied sites were located in regions of seismic intensity VIII. However, liquefaction phenomena at ten different sites in regions of seismic intensity VI were also observed for the first time in China mainland. Sandboils and waterspouts ranged from centimeters to tens of meters, with most between 1 m to 3 m. Dramatically high water/sand ejections, e.g., more than 10 m, were observed at four different sites. The sand ejections included silty sand, fine sand, medium sand, course sand and gravel, but the ejected sand amount was less than that in the 1976 Tangshan earthquake. Possible liquefaction of natural gravel soils was observed for the first time in China mainland.

Site effects by generalized inversion technique using strong motion recordings of the 2008 Wenchuan earthquake

The generalized inversion of S-wave amplitude spectra from the free-field strong motion recordings of the China National Strong Motion Observation Network System （NSMONS） are used to evaluate the site effects in the Wenchuan area. In this regard, a total of 602 recordings from 96 aftershocks of the Wenchuan earthquake with magnitudes of M3.7-M6.5 were selected as a dataset. These recordings were obtained from 28 stations at a hypocenter distance ranging from 30 km to 150 km. The inversion results have been verified as reliable by comparing the site response at station 62WUD using the Generalized Inversion Technique （GIT） and the Standard Spectral Ratio method （SSR）. For all 28 stations, the site predominant frequency F and the average site amplification in different frequency bands of 1.0-5.0 Hz, 5.0-10.0 Hz and 1.0-10.0 Hz have been calculated based on the inversion results. Compared with the results from the horizontal-to-vertical spectral ratio （HVSR） method, it shows that the HVSR method can reasonably estimate the site predominant frequency but underestimates the site amplification. The linear fitting between the average site amplification for each frequency band and the V20 （the average uppermost-20 m shear wave velocity） shows good correlation. A distance measurement called the asperity distance DAspt is proposed to reasonably characterize the source-to-site distance for large earthquakes. Finally, the inversed site response is used to identify the soil nonlinearity in the main shock and aftershocks of Wenchuan earthquake. In ten of the 28 stations analyzed in the main shock, the soil behaved nonlinearly, where the ground motion level is apparently beyond a threshold ofPGA 〉 300 cm/s^2 or PGV 〉 20 cm/s, and only one station coded 51SFB has evidence of soil nonlinear behavior in the aftershocks.

Coseismic vertical deformation of the M_S8.0 Wenchuan earthquake from repeated levelings and its constraint on listric fault geometry

The devastating Ms8.0 Wenchuan earthquake ruptured two large parallel thrust faults along the middle segment of the Longmenshan thrust belt. Preseismic and postseismic leveling data indicated the hanging wall of the Yingxiu-Beichuan-Nanba thrust fault mainly presented coseismic uplift with respect to the reference point at Pingwu county town, and the observed maximum uplift of 4.7 m is located at Beichuan county （Qushan town） which is about 100 m west of the fault scarp. The foot wall of the Yingxiu-Beichuan-Nanba thrust fault mainly showed subsidence with maximum subsidence of 0.6 m near the rupture. By employing a listric dislocation model, we found that the fault geometry model of exponential dip angle δ=88°×[1-exp（-9/h）] with depth of 18 km and uniform thrust-slip of 5.6 m could fit the observed coseismic vertical deformation very well, which verifies the listric thrust model of the Longmenshan orogenic zone.

Co-seismic Landslide Inventory and Susceptibility Mapping in the 2008 Wenchuan Earthquake Disaster Area,China

The Ms 8.0 May 12,2008 Wenchuan earthquake triggered tens of thousands of landslides.The widespread landslides have caused serious casualties and property losses,and posed a great threat to post-earthquake reconstruction.A spatial database,inventoried 43,842 landslides with a total area of 632 km 2,was developed by interpretation of multi-resolution remote sensing images.The landslides can be classified into three categories:swallow,disrupted slides and falls;deep-seated slides and falls,and rock avalanches.The correlation between landslides distribution and the influencing parameters including distance from co-seismic fault,lithology,slope gradient,elevation,peak ground acceleration(PGA) and distance from drainage were analyzed.The distance from co-seismic fault was the most significant parameter followed by slope gradient and PGA was the least significant one.A logistic regression model combined with bivariate statistical analysis(BSA) was adopted for landslide susceptibility mapping.The study area was classified into five categories of landslide susceptibility:very low,low,medium,high and very high.92.0% of the study area belongs to low and very low categories with corresponding 9.0% of the total inventoried landslides.Medium susceptible zones make up 4.2% of the area with 17.7% of the total landslides.The rest of the area was classified into high and very high categories,which makes up 3.9% of the area with corresponding 73.3% of the total landslides.Although the susceptibility map can reveal the likelihood of future landslides and debris flows,and it is helpful for the rebuilding process and future zoning issues.