采用高能球磨法制备了用于热浸镀锌的纳米C eO2/Zn复合粉末,并利用X射线衍射(X-ray d iffraction,XRD)、X射线光电子能谱(X-ray photoe lectron spectroscopy,XPS)、透射电镜(T ransm iss ion e lectron m i-croscopy,TEM)、扫描电镜(Sc...采用高能球磨法制备了用于热浸镀锌的纳米C eO2/Zn复合粉末,并利用X射线衍射(X-ray d iffraction,XRD)、X射线光电子能谱(X-ray photoe lectron spectroscopy,XPS)、透射电镜(T ransm iss ion e lectron m i-croscopy,TEM)、扫描电镜(Scann ing e lectron m icroscopy,SEM)以及能谱分析(X-ray energy d ispers ive spec-trum,EDS)等方法,对复合粉末的显微结构、表面成分、晶粒大小、微观形貌以及元素分布进行了研究。结果表明,随着球磨时间的延长,纳米C eO2硬团聚体逐渐解聚,Zn晶粒不断细化,形成层片状复合粉末;球磨120 m in后纳米C eO2粒子分散良好,呈理想的单个均匀弥散分布状态包覆在Zn颗粒上形成近似球形的复合粒子,其粒径分布均匀。展开更多
In this work,a novel ultrahigh-strength Al-10Zn-3.5Mg-1.5Cu alloy was fabricated by powder metallurgy followed by hot extrusion.Investigations on microstructural evolution and mechanical properties of the fabricated s...In this work,a novel ultrahigh-strength Al-10Zn-3.5Mg-1.5Cu alloy was fabricated by powder metallurgy followed by hot extrusion.Investigations on microstructural evolution and mechanical properties of the fabricated samples were carried out.The results show that the grain size of sintered samples matches with the powder particles after ball milling.The relative densities of sintered and hot extruded samples reach 99.1%and 100%,respectively.Owing to the comprehensive mechanism of grain refinement,aging and dispersion strengthening,the ultimate tensile strength,yield strength and elongation of the Al-10Zn-3.5Mg-1.5Cu alloy after hot extrusion and subsequent heat treatment achieve 810 MPa,770 MPa and 8%,respectively.展开更多
Powder extrusion, which is based on the superplastic behavior of Zn-22%A1 eutectoid alloy, was proposed to reduce the forming load and promises to provide fine microstructures in the manufacture of miniature helical g...Powder extrusion, which is based on the superplastic behavior of Zn-22%A1 eutectoid alloy, was proposed to reduce the forming load and promises to provide fine microstructures in the manufacture of miniature helical gears. The specifications of the helical gears were as follows： module, 0.3; number of teeth, 12; and helix angle, 15°. Compacted powders were consolidated by sintering and solution heat treatment. The consolidated billets consisted of lamellar and fine-grained microstructures. Extrusion experiments were carried out under the following conditions： temperature, 250 ℃; strain rates, 2.36× 10-3 s^-1 and 1.18× 10^-1 s-1. The mechanical properties of the extruded helical gears were investigated by measurement of the Vickers hardness and extrusion load, and by scanning electron microscopy.展开更多
文摘采用高能球磨法制备了用于热浸镀锌的纳米C eO2/Zn复合粉末,并利用X射线衍射(X-ray d iffraction,XRD)、X射线光电子能谱(X-ray photoe lectron spectroscopy,XPS)、透射电镜(T ransm iss ion e lectron m i-croscopy,TEM)、扫描电镜(Scann ing e lectron m icroscopy,SEM)以及能谱分析(X-ray energy d ispers ive spec-trum,EDS)等方法,对复合粉末的显微结构、表面成分、晶粒大小、微观形貌以及元素分布进行了研究。结果表明,随着球磨时间的延长,纳米C eO2硬团聚体逐渐解聚,Zn晶粒不断细化,形成层片状复合粉末;球磨120 m in后纳米C eO2粒子分散良好,呈理想的单个均匀弥散分布状态包覆在Zn颗粒上形成近似球形的复合粒子,其粒径分布均匀。
基金Project(FRF-GF-19-012AZ)supported by the Fundamental Research Funds for the Central Universities,China。
文摘In this work,a novel ultrahigh-strength Al-10Zn-3.5Mg-1.5Cu alloy was fabricated by powder metallurgy followed by hot extrusion.Investigations on microstructural evolution and mechanical properties of the fabricated samples were carried out.The results show that the grain size of sintered samples matches with the powder particles after ball milling.The relative densities of sintered and hot extruded samples reach 99.1%and 100%,respectively.Owing to the comprehensive mechanism of grain refinement,aging and dispersion strengthening,the ultimate tensile strength,yield strength and elongation of the Al-10Zn-3.5Mg-1.5Cu alloy after hot extrusion and subsequent heat treatment achieve 810 MPa,770 MPa and 8%,respectively.
基金Project (2010-0008-277) supported by the NCRC (National Core Research Center) Program through the National Research Foundation of Korea,funded by the Ministry of Education,Science,and TechnologyProject (NRF-2009-K20601000004-09E0100-00410) supported by PNU-IFAM JRC
文摘Powder extrusion, which is based on the superplastic behavior of Zn-22%A1 eutectoid alloy, was proposed to reduce the forming load and promises to provide fine microstructures in the manufacture of miniature helical gears. The specifications of the helical gears were as follows： module, 0.3; number of teeth, 12; and helix angle, 15°. Compacted powders were consolidated by sintering and solution heat treatment. The consolidated billets consisted of lamellar and fine-grained microstructures. Extrusion experiments were carried out under the following conditions： temperature, 250 ℃; strain rates, 2.36× 10-3 s^-1 and 1.18× 10^-1 s-1. The mechanical properties of the extruded helical gears were investigated by measurement of the Vickers hardness and extrusion load, and by scanning electron microscopy.
