Exploring the effect of cooling rate on non-isothermal crystallization of copolymer polypropylene by fast scanning calorimetry

Polypropylene is commonly used as a binder for ceramic injection molding,and rapid cooling is often encountered during processing.However,the crystallization behavior of polypropylene shows a strong dependence on cooling rate due to its semi-crystalline characteristics.Therefore,the influence of cooling rate on the quality of final product cannot be ignored.In this study,the fast differential scanning calorimetry(FSC)test was performed to study the influence of cooling rate on the non-isothermal crystallization behavior and non-isothermal crystallization kinetics of a copolymer polypropylene(PP BC03B).The results show that the crystallization temperatures and crystallinity decrease as the cooling rate increases.In addition,two exothermic peaks occur when cooling rate ranges from 30 to 300 K·s^(-1),indicating the formation of another crystal phase.Avrami,Ozawa and Mo equations were used to explore the non-isothermal crystallization kinetics,and it can be concluded that the Mo method is suitable for this study.

Syntheses and properties of associative acrylamide copolymers containing short hydrophobic chains used in a friction reducer for slick-water fracturing

Two allyldimethylalkyl quaternary ammonium salt(AQAS)monomers,N,N-dimethylallylphenylpropylammonium bromide(AQAS1)and N,N-dimethylallylnonylammonium bromide(AQAS2),were synthesized and used to prepare modified polyacrylamide materials.Two new drag reducers were synthesized from acrylamide(AM),sodium acrylate(Na AA)and a cationic modified monomer(AQAS1 or AQAS2)via aqueous solution polymerization,and the copolymers were named P(AM/Na AA/AQAS1)and P(AM/Na AA/AQAS2),respectively.The structures of the drag reduction agents were confirmed by IR and1H NMR spectroscopies.The molecular weight(Mw)of P(AM/Na AA/AQAS1)was 1.79×10^(6)g/mol.When the copolymer concentration was 1000 mg/L and the flow rate was 45 L/min,in fresh water the highest drag reduction rate was 75.8%,in 10,000 mg/L Na Cl solution the drag reduction rate decreased to 72.9%.The molecular weight of P(AM/Na AA/AQAS2)was 3.17×10^(6)g/mol.When the copolymer concentration was500 mg/L and the flow rate was 45 L/min,the drag reduction rate reached 75.2%,and in 10,000 mg/L Na Cl solution the drag reduction rate was 73.3%,decreased by approximately 1.9%.The drag reduction rate for partially hydrolyzed polyacrylamide(HPAM)was also investigated,and the results showed that the drag reduction rates for 500 and 1000 mg/L HPAM solutions were merely 43.2%and 49.0%in brine,respectively.Compared with HPAM,both of the above copolymers presented better drag reduction capacities.

A Non-parametric Gradient-Based Shape Optimization Approach for Solving Inverse Problems in Directed Self-Assemblyof Block Copolymers

We consider the inverse problem of finding guiding pattern shapes that result in desired self-assembly morphologies of block copolymer melts.Specifically,we model polymer selfassembly using the self-consistent field theory and derive,in a non-parametric setting,the sensitivity of the dissimilarity between the desired and the actual morphologies to arbitrary perturbations in the guiding pattern shape.The sensitivity is then used for the optimization of the confining pattern shapes such that the dissimilarity between the desired and the actual morphologies is minimized.The efficiency and robustness of the proposed gradient-based algorithm are demonstrated in a number of examples related to templating vertical interconnect accesses(VIA).

Advancements in Polymer Science: Synthesis, Characterization, and Biomedical Applications of Homopolymers and Copolymers

Polymer science encompasses a different range of materials critical to industries spanning from packaging to biomedicine. Understanding the synthesis, characterization, and applications of common homopolymers and copolymers is fundamental to advancing polymer research and development. In this comprehensive review, we explore various preparation methods, including free radical, anionic, and cationic polymerization, utilized for synthesizing homopolymers and copolymers. Furthermore, we investigate solvent choices commonly employed for polymer characterization, ranging from neat conditions, polar protic and polar aprotic solvents. We also explored characterization techniques, including Fourier Transform Infrared Spectroscopy (FTIR), Nuclear Magnetic Resonance (NMR), Atomic Force Microscopy (AFM), Differential Scanning Calorimetry (DSC), and Thermogravimetric Analysis (TGA). In addition to industrial applications, we highlight the diverse biological applications of homopolymers, poly(2-hydroxyethyl methacrylate) (pHEMA) and polystyrene, which find its extensive use in biomedicine. By synthesizing and analyzing this wealth of information, this review aims to provide a comprehensive understanding of the synthesis, characterization, and applications of homopolymers and copolymers, with a particular focus on their biological applications. This holistic approach not only contributes to advancements in polymer science and technology but also fosters innovation in biomedicine, ultimately benefiting human health and well-being.

Influence ofβ-nucleating Compound Agents on the Mechanical Properties and Crystallization Behavior of Polypropylene Random Copolymer

A novel polypropylene random(PPR)composite materials with optimized properties was developed by addingβ-nucleating compound agents(rare earth complex WBG-2 and aryl amide derivative TMB-5)and ternary compound modifier(TPE/WBG-2/CaCO_(3)).The effects of differentβ-nucleating agents and ternary compound modifier on the mechanical properties and crystallization behavior of PPR were analyzed.The results show that,compared with pure PPR materials,both WBG-2 and TMB-5 could significantly improve the impact strength of PPR.The crystallization temperature of PPR increased with the addition ofβ-nucleating agent.The modified PPR prepared with ternary compound modifier showed the most excellent comprehensive properties.

A fast ionic transport copolymeric network for stable quasi-solid lithium metal battery

Solid-state lithium(Li) metal batteries overwhelm the lithium-ion batteries by harvesting high energy from Li metal anode with ultrahigh capacities and gaining excellent safety from solid electrolytes.However,the uncontrollable solvents in solid electrolytes usually aggravate poor interfacial contact with lithium metal anode and deteriorate Li^(+) pathways.Here a copolymeric network-structured ion conductor by rationally integrating cellulose nanofibril as a two-in-one functional material is employed to anchor the solvent.Taking advantages of tightly anchoring of cellulose nanofibril to solvent,the asconstructed quasi-solid polymer-based electrolyte offers rapid Li^(+) transport channels and realizes effective Li-dendrite suppression,which enables high ionic conductivity of 1.93 × 10^(-3)S cm^(-1) at room temperature,long-term Li plating/stripping over 1900 h,and high capacity retention of 99%.This work provides a fresh strategy for creating solid electrolytes that meet both high ionic conductivity and interfacial stability requirements for practical solid-state lithium metal battery.

Research on the Marine Antifouling Ability and Mechanism of Acrylate Copolymers and Marine Coatings Based on a Synergistic Effect

Marine biofouling is an urgent global problem in the process of ocean exploitation and utilization.In our work,a series of zinc-based acrylate copolymers(ACZn-x)were designed and synthesized using benzoic acid,zinc oxide(ZnO)and a random quaternion copolymer consisting of ethyl acrylate(EA),butyl acrylate(BA),acrylic acid(AA)and methacrylic acid(MAA)by free radical polymerization and dehydration condensation.The ACZn-x with a zinc benzoate side chain is able to hydrolyze in natural seawater under static conditions,resulting in the formation of a smooth surface.We investigated and confirmed the antifouling(AF)behavior of ACZn-x in the laboratory and revealed that they have better antibacterial(86%for S.aureus and 72%for E.coli)and anti-algal(≥60.1%for N.closterium and≥67.5%for P.subcordiformis)activities.We also assessed the marine AF properties of ACZn-x and corresponding coatings in Qingdao,China;the ACZn-x exhibited ideal AF properties with little silt and biological mucosa adhered to the ACZn-x surface after 6 months,and corresponding coatings exhibited little biofouling after 16 months in the ocean.Importantly,possible AF mechanisms were further proposed at the cellular level.These results could be helpful for the development and application of effective AF coatings.

Ethylene Copolymerization with Linear and End-Cyclized Olefins via a Metallocene Catalyst:Polymerization Behavior and Thermal Properties of Copolymers

Olefin solution polymerization can be used to obtain high-performance polyolefin materials that cannot be obtained via other polymerization processes.Polyolefin elastomers(POE)are a typical example.Due to cost,only a few linear a-olefins(e.g.,1-butene,1-hexene,and 1-octene)are used as comonomers in solution polymerization in industry.However,a-olefin comonomers with other structures may have different effects on polymerization in comparison with common linear ones.Moreover,the properties of the corresponding materials may differ significantly.In this work,copolymers of ethylene with linear and endcyclized a-olefins are synthesized using a metallocene catalyst.The copolymerization of ethylene with linear a-olefins results in a higher turn-over frequency(TOF)and lower incorporation than copolymerization with end-cyclized a-olefins,which may indicate that end-cyclized a-olefins have a higher coordination probability and lower insertion rate.In this reaction,the comonomer is distributed randomly in the polymer chain and efficiently destroys crystallization.End-cyclized a-olefins exhibit a much stronger crystallization destructive capacity(CDC)in the copolymer than linear a-olefins,possibly because linear a-olefins act mainly in the radial direction of the main chain of the polymer,while end-cyclized a-olefins act mainly in the axial direction of the main chain.

Highly efficient organic solar cells with improved stability enabled by ternary copolymers with antioxidant side chains

The stability of organic solar cells(OSCs)remains a major concern for their ultimate industrialization due to the photo,oxygen,and water susceptibility of organic photoactive materials.Usually,antioxidant additives are blended as radical scavengers into the active layer.However,it will induce the intrinsic morphology instability and adversely affect the efficiency and long-term stability.Herein,the antioxidant dibutylhydroxytoluene(BHT)group has been covalently linked onto the side chain of benzothiadiazole(BT)unit,and a series of ternary copolymers D18-Cl-BTBHTx(x=0,0.05,0.1,0.2)with varied ratio of BHT-containing side chains have been synthesized.It was found that the introduction of BHT side chains would have a negligible effect on the photophysical properties and electronic levels,and the D18-Cl-BTBHT0.05:Y6-based OSC achieved the highest power conversion efficiency(PCE)of 17.6%,which is higher than those based active layer blended with BHT additives.More importantly,the unencapsulated device based on D18-Cl-BTBHTx(x=0.05,0.1,0.2)retained approximately 50%of the initial PCE over 30 hours operation under ambient conditions,significantly outperforming the control device based on D18-Cl(90%degradation in PCE after 30 h).This work provides a new structural design strategy of copolymers for OSCs with simultaneously improved efficiency and stability.

QUANTITATIVE EVALUATION OF ARRANGEMENT OF MONOMERS IN LINEAR BINARY COPOLYMERS USING A MONTE CARLO SIMULATION METHOD

A Monte Carlo method was used to take thorough account of the influences of different reactivity ratios and initial feed compositions on copolymer microstructure.The model proves the lack of azeotropic behavior in systems in which r_A>1 and r_B<1 or vice versa;it is also able to calculate the drift in the copolymer properties:copolymer composition,and randomness parameter.Moreover,for each reactivity ratio pair given,there is a unique reaction conversion,at which macromolecules produced inherit their ...

Pyrolysis-Gas Chromatography/Mass Spectrometry for Microstructure and Pyrolysis Pathway of Polyester-Polyether Multiblock Copolymer

The composition and sequence distribution of monomeric units in polyester polyether multiblock copolymer were studied by pyrolysis? gas chromatography (PGC) and pyrolysis gas chromatography/mass spectrometry (PGC/MS). PGC was applied to study the F t curve of the multiblock copolymer and PGC/MS was used to separate and identify the pyrolyzates. DTA experiment was used to study the decomposition temperature. The results show that the beginning point of elastomer’s decomposition was about 300?℃ and the decomposition temperature of most of the sample was 550?℃. Many pyrolyzates were produced because of the breaking of weak bonds in the sample. The possible microstructure was verified and the pyrolysis pathway of the copolymer was investigated.

MOLECULAR DESIGN SYNTHESIS AND PROPERTIES OF SIX KINDS OF MULTIPHASE (STYRENE-ETHYLENE OXIDE)COPOLYMERS

Multiphase copolymers of styrene (S) and ethylene oxide (EO) are amphiphilic, because of the hydrophobic and amorphous polystyrene (PS) segments and the hydrophilic and crystalline polyoxyethylene (PEO). They have many uses including polymeric surfactants, electrostatic charge reducers, compatibilizer in polymer

Removal of manganese from waste water by complexation-ultrafiltration using copolymer of maleic acid and acrylic acid

Copolymer of maleic acid and acrylic acid （PMA-100）, combining with polyvinyl butyral （PVB） ultrafiltration membrane was used for the removal of Mn（II） from waste water by complexation-ultrafiltration. The carboxylic group content of PMA-100 and the rate of complexation reaction were measured. Effects of the mass ratio of PMA-100 to Mn（II） （n）, pH, background electrolyte, etc on the rejection rate （R） and permeate flux （J） were investigated. The results show that carboxylic group content of PMA-100 is 9.5 mmol/g. The complexation of Mn（II） with PMA-100 is rapid and completed within 5 min at pH 6.0. Both R and J increase with pH increasing in the range of 2.5-7.0, and R increases with the increase of n at pH 6.0 while J is little affected. The background electrolyte leads to the decrease of R, and CaCl2 has much greater effect on R than NaCl at the same ionic strength.

Degradation of PBS-Based Copolymers and Impacts on the Growth of Winter Wheat

[Objective] The degradation properties of PBS-based copolymers and impacts on the growth of winter wheat were studied.[Method] Seeds of winter wheat were sown and cultivated in soil,and mixed with equal amounts of PBS,PBS-co-HS and PBS-co-BA,to investigate the degradation of polymers in soil and effects of the degradation intermediates and degradation products on seed germination and the growth of winter wheat during the continuous process of degradation.[Result] The results showed that the copolymers had better biodegradation properties than PBS in Lou Soil in Shaanxi Province under the same condition;polymer treatments had not affected the germination percentage and plant height of the winter wheat but contributed to the improvement of plant biomass.[Conclusion] These results suggested that the degradation and degradation products of PBS,PBS-co-HS and PBS-co-BA had not affected the growth of plants in soil environment for temporary.

Synthesis of an Amphiphilic Dendrimer-Like Block Copolymer and Its Application on Drug Delivery

Dendrimer-like amphiphilic copolymer is a kind of three-dimensional spherical structure polymer. An amphiphilic dendrimer-like diblock copolymer, PEEGE-G2-b-PEO（OH）12, constituted of a hydrophobic poly（ethoxyethyl glycidol ether） inner core and a hydrophilic poly（ethylene oxide） outer layer, has been successfully synthesized by the living anionic ring-opening polymerization method. The intermediates and targeted products were charac-terized with 1H NMR spectroscopy and gel permeation chromatography. The application on drug delivery of dendrimer-like diblock copolymer PEEGE-G2-b-PEO（OH）12 using DOX as a model drug was also studied. The drug loading content and encapsulation e ciency were found at 13.07% and 45.75%, respectively. In vitro release experiment results indicated that the drug-loaded micelles exhibited a sustained release behavior under acidic media.

Synthesis and application of lignin-based copolymer LSAA on controlling non-point source pollution resulted from surface runoff

In this article,alkali lignin separated from paper pulp waste was grafted into a novel copolymer LSAA (a copolymer of lignin,starch, acrylamide,and acrylic acid).Its practical application effect and environmental safety were studied.The results of field simulation experiment indicated that the application of LSAA significantly affected the output of the runoff and pollutants.The runoff quantity was decreased by 16.67%-47.00%and the loads of total suspended solids (TSS),chemical oxygen demand (COD),total nit...

NONBRIDGED HALF-TITANOCENES CONTAINING ANIONIC ANCILLARY DONOR LIGANDS:PROMISING NEW CATALYSTS FOR PRECISE SYNTHESIS OF CYCLIC OLEFIN COPOLYMERS(COCs)

Precise,efficient copolymerizations of ethylene with cyclic olefins[norbornene(NBE),cyclopentene(CPE)]using nonbridged half-titanocenes of type,Cp TiCl_2(L)(Cp =cyclopentadienyl group,L=aryloxo,ketimide)-MAO catalyst systems have been summarized.CpTiCl_2(N=C Bu_2)exhibited both remarkable catalytic activity and efficient NBE incorporation for ethylene/NBE copolymerization:the NBE incorporation by Cp TiCl_2(X)(X=N=C Bu_2,O-2,6- Pr_2C_6H_3; Cp =Cp,C_5Me_5,indenyl)was related to the calculated coordination ene...

Phase Partition of Acrylonitrile(AN)in Vinylidene Chloride(VDC)/Water System and Its Effect on VDC-AN Copolymer Composition

Phase partition of acrylonitrile in the vinylidene chloride/water system at different temperature and under pressure was studied. A calculation method for average VDC-AN copolymer composition with AN phase partition considered was proposed. The calculated results are in good agreement with the experimental data nearly the entire conversion range. VDC-AN copolymer with narrower composition distribution can be prepared in the suspension process and interpreted with dynamic equilibrium of AN between the oil and water phases continuously.

Novel synthesis metal 3-alkylthiophene copolymer

Copolymer, regiorandom and regioregular poly （ 3-octylthiophene ）-co-poly （ 3-（ 2-ethyl-1- hexylthiophene））（P3OTIOT） was synthesized by a FeCl3-oxidation and GRIM （grignard method） approach. The structure and optical properties were verified by the Fourier transform infrared, ultraviolet visible spectroscopy, NMR （nuclear magnetic resonance ）, gel permeation chromatography （GPC） and photoluminescence （PL）. The results indicate that the band-gap energy of the regioregular HT P3OTEHT was lower than that of the regiorandom copolymer and both of them depict low band-gap energy, high photoluminescence quantum yield, excellent solubility and processability, and might be promising polymer materials for applications in polymer light-emitting diodes, light-emitting electrochemical cells and polymer solar cells, etc.

Dissipative Particle Dynamics Simulation of Microscopic Properties in Diblock Copolymer Films

Mean-square bond length, root-mean-square end-to-end distance and gyration radius in diblock copolymer films have been studied by dissipative particle dynamics simulations. Results show evident linear trends of any property separately with the thickness of film, the interaction between particles of different types, the repulsion between particle and boundary, except for the dependence of the variations of mean-square bond length on the thickness of film, which exhibits as a wave trend. What＇s more, the varying trends of mean-square bond length and root-mean-square end-to-end distance can correspond to each other. The density distribution of either component in diblock copolymer film can be controlled and adjusted effectively through its interaction with boundary.