Although the cyclic rotation of the principal stress direction is important,its effect on the deformation behavior and dynamic properties of the reinforced soil has not been reported to date.Tests carried out on large...Although the cyclic rotation of the principal stress direction is important,its effect on the deformation behavior and dynamic properties of the reinforced soil has not been reported to date.Tests carried out on large-scale hollow cylinder samples reveal that the cyclic rotation of the principal stress direction results in significant variations of strain components(ε,ε,εand γ) with periodic characteristics despite the deviatoric stress being constant during tests.This oscillation can be related to the corresponding variations in the stress components and the anisotropic fabric that rotate continuously along the principal stress direction.Sand under rotation appears to develop a plastic strain.Similar trends are observed for reinforced sand,but the shear interaction,the interlocking between particles and reinforcement layer,and the confinement result in significant reductions in the induced strains and associated irrecoverable plastic strains.Most of the strains occur in the first cycle,and as the number of cycles increases,the presence of strains becomes very small,which is almost insignificant.This indicates that the soil has reached anisotropic critical state(ACS),where a stable structure is formed after continuous orientation,realignment and rearrangement of the particles accompanied with increasing cyclic rotation.Rotation in the range of 60°-135° produces more induced strains even in the presence of the reinforcement,when compared with other ranges.This relates to the extension mode of the test in this range in which σ>σand to the relative approach between the mobilized plane and the weakest horizontal plane.Reinforcement results in an increase in shear modulus while it appears to have no effect on the damping ratio.Continuous cycles of rotation result in an increase in shear modulus and lower damping ratio due to the densification that causes a decrease in shear strain and less dissipation of energy.展开更多
饱和粉土在地震作用下会发生液化变形,从而导致建立在其上的建(构)筑物发生破坏。工程场地区域内粉土单元通常存在初始剪应力作用,为探究初始剪应力对饱和粉土液化特性的影响,将液化后粉土视为流体进行了一系列循环扭剪试验研究。试验...饱和粉土在地震作用下会发生液化变形,从而导致建立在其上的建(构)筑物发生破坏。工程场地区域内粉土单元通常存在初始剪应力作用,为探究初始剪应力对饱和粉土液化特性的影响,将液化后粉土视为流体进行了一系列循环扭剪试验研究。试验结果表明,初始剪应力对饱和粉土剪应力-剪应变率曲线影响显著,随着初始剪应力τ_(s)的增大,剪应力-剪应变率曲线由“椭圆形”向“哑铃形”过渡逐渐转变为由“镰刀形”向“椭圆形”至“锤形”过渡;表观黏度η与振次N的衰减曲线随着τ_(s)的增大先降低再抬升,平均流动系数κ与振次N的增长曲线发展速度随着τ_(s)的增大先加快后减慢,固液相变孔压比r_(uth)随着τ_(s)的增大先减小后增大,当τ_(s)=5 k Pa时饱和粉土的r_(uth)最小。展开更多
The cracking behaviour of X-70 pipeline steel in near-neutral pH solutions was studied under different modes of cyclic loading. The crack propagation process of X-70 pipeline steel under low frequency cyclic loading c...The cracking behaviour of X-70 pipeline steel in near-neutral pH solutions was studied under different modes of cyclic loading. The crack propagation process of X-70 pipeline steel under low frequency cyclic loading condition was controlled mainly by stress corrosion cracking （SCC） mechanism. Under mixed-mode cyclic loading, both higher tensile stress and shear stress made cracks easier to propagate. Applied cathodic potentials and high content of carbon dioxide in solutions also promoted the propagation of cracks. The propagation directions of cracks were different under different cyclic loading conditions. Under mode I （pure tensile stress） cyclic loading condition, cracks were straight and perpendicular to the tensile stress axis, while under mixed-mode 1/111 （tensile/shear stress） cyclic loading,cracks were sinuous and did not propagate in the direction perpendicular to the main tensile stress axis. Under the mixed-mode cyclic loading, cracks were much easier to propagate, suggesting that shear stress intensified the role of tensile stress. In addition, shear stress promoted the interaction between cracks, resulting in easier coalescence of cracks.展开更多
Stiffness degradation will occur due to the generation of accumulated pore pressure in saturated soft clays under cyclic loading. The soil static-dynamic multi-purpose triaxial and torsional shear apparatus in Dalian ...Stiffness degradation will occur due to the generation of accumulated pore pressure in saturated soft clays under cyclic loading. The soil static-dynamic multi-purpose triaxial and torsional shear apparatus in Dalian University of Technology was employed to perform different types of test on the saturated soft marine clay in the Yangtze Estuary. Undisturbed samples of the clay were subjected to undrained cyclic vertical and torsional coupling shear and cyclic torsional shear after three-directional anisotropic consolidation with different initial consolidation parameters. Investigated were the effects of the initial orientation angle of the major principal stress, initial ratio of deviatoric stress, initial coefficient of intermediate principal stress and continuous rotation of principal stress axes on the stiffness degradation. It is found that the degradation index decreases （or degradation degree increases） significantly with increasing initial orientation angle of the major principal stress and initial ratio of deviatoric stress. Compared with the effects of the initial orientation angle of the major principal stress and initial ratio of deviatoric stress, the effect of initial coefficient of intermediate principal stress is less evident and this trend is more clearly reflected by the results of the cyclic torsional shear tests than those of the cyclic coupling shear tests. At the same cycle number, the degradation index obtained from the cyclic torsional shear test is higher than that from the cyclic coupling shear test. The main reason is that the continuous rotation in principal stress directions during cyclic coupling shear damages the original structure of the soil more than the cyclic torsional shear does.Based on a series of experiments, a mathematical model for stiffness degradation is proposed and the relevant parameters are determined.展开更多
A series of dynamic behavior tests on Nanjing flake-shaped fine sand were performed by using the WFI cyclic triaxial apparatus made in England. The dynamic behaviors of Nanjing flake-shaped fine sand under different s...A series of dynamic behavior tests on Nanjing flake-shaped fine sand were performed by using the WFI cyclic triaxial apparatus made in England. The dynamic behaviors of Nanjing flake-shaped fine sand under different static deviator stress levels and cyclic stress ratios were studied. Through comparing the effective stress path under cyclic loading with static loading, the processes of liquefaction of saturated Nanjing flake-shaped fine sand with development of dynamic pore-water pressure, including the initial compact state, compression state and dilative state, were investigated. The variation of the shear stiffness with the number of cycles and cyclic strain was investigated by analyzing the secant shear modulus in each unload-reload loop of dynamic stress-strain relationship. And by means of the exponential function, the empirical equations of the relationship between secant shear modulus Gsec, shear modulus ratio Gsec/Gmax and cyclic strain ε were established based on series of test results. The results show that according to different combinations of static deviator stress and cyclic stress, two kinds of failure patterns with deviator stress reversal or no deviator stress reversal are observed in the samples tested in this series, including cyclic mobility and the failure of accumulation residual strain. In addition, the degradation of dynamic shear modulus is due to the development of vibration pore-water pressure and it is observed that the shear modulus reduces with the progressive number of cycles.展开更多
文摘Although the cyclic rotation of the principal stress direction is important,its effect on the deformation behavior and dynamic properties of the reinforced soil has not been reported to date.Tests carried out on large-scale hollow cylinder samples reveal that the cyclic rotation of the principal stress direction results in significant variations of strain components(ε,ε,εand γ) with periodic characteristics despite the deviatoric stress being constant during tests.This oscillation can be related to the corresponding variations in the stress components and the anisotropic fabric that rotate continuously along the principal stress direction.Sand under rotation appears to develop a plastic strain.Similar trends are observed for reinforced sand,but the shear interaction,the interlocking between particles and reinforcement layer,and the confinement result in significant reductions in the induced strains and associated irrecoverable plastic strains.Most of the strains occur in the first cycle,and as the number of cycles increases,the presence of strains becomes very small,which is almost insignificant.This indicates that the soil has reached anisotropic critical state(ACS),where a stable structure is formed after continuous orientation,realignment and rearrangement of the particles accompanied with increasing cyclic rotation.Rotation in the range of 60°-135° produces more induced strains even in the presence of the reinforcement,when compared with other ranges.This relates to the extension mode of the test in this range in which σ>σand to the relative approach between the mobilized plane and the weakest horizontal plane.Reinforcement results in an increase in shear modulus while it appears to have no effect on the damping ratio.Continuous cycles of rotation result in an increase in shear modulus and lower damping ratio due to the densification that causes a decrease in shear strain and less dissipation of energy.
文摘饱和粉土在地震作用下会发生液化变形,从而导致建立在其上的建(构)筑物发生破坏。工程场地区域内粉土单元通常存在初始剪应力作用,为探究初始剪应力对饱和粉土液化特性的影响,将液化后粉土视为流体进行了一系列循环扭剪试验研究。试验结果表明,初始剪应力对饱和粉土剪应力-剪应变率曲线影响显著,随着初始剪应力τ_(s)的增大,剪应力-剪应变率曲线由“椭圆形”向“哑铃形”过渡逐渐转变为由“镰刀形”向“椭圆形”至“锤形”过渡;表观黏度η与振次N的衰减曲线随着τ_(s)的增大先降低再抬升,平均流动系数κ与振次N的增长曲线发展速度随着τ_(s)的增大先加快后减慢,固液相变孔压比r_(uth)随着τ_(s)的增大先减小后增大,当τ_(s)=5 k Pa时饱和粉土的r_(uth)最小。
基金This work was supported by the Special Funds for the Major State Basic Research Projects in China(No.G19990650)also supported by the Science and Technology Comm is—sion of Shanghai Municipality(Projects Nos.025258036 and 02ZE14031
文摘The cracking behaviour of X-70 pipeline steel in near-neutral pH solutions was studied under different modes of cyclic loading. The crack propagation process of X-70 pipeline steel under low frequency cyclic loading condition was controlled mainly by stress corrosion cracking （SCC） mechanism. Under mixed-mode cyclic loading, both higher tensile stress and shear stress made cracks easier to propagate. Applied cathodic potentials and high content of carbon dioxide in solutions also promoted the propagation of cracks. The propagation directions of cracks were different under different cyclic loading conditions. Under mode I （pure tensile stress） cyclic loading condition, cracks were straight and perpendicular to the tensile stress axis, while under mixed-mode 1/111 （tensile/shear stress） cyclic loading,cracks were sinuous and did not propagate in the direction perpendicular to the main tensile stress axis. Under the mixed-mode cyclic loading, cracks were much easier to propagate, suggesting that shear stress intensified the role of tensile stress. In addition, shear stress promoted the interaction between cracks, resulting in easier coalescence of cracks.
基金supported bythe National Natural Science Foundation of China(Grant Nos.50579006,50639010 and 50909014)
文摘Stiffness degradation will occur due to the generation of accumulated pore pressure in saturated soft clays under cyclic loading. The soil static-dynamic multi-purpose triaxial and torsional shear apparatus in Dalian University of Technology was employed to perform different types of test on the saturated soft marine clay in the Yangtze Estuary. Undisturbed samples of the clay were subjected to undrained cyclic vertical and torsional coupling shear and cyclic torsional shear after three-directional anisotropic consolidation with different initial consolidation parameters. Investigated were the effects of the initial orientation angle of the major principal stress, initial ratio of deviatoric stress, initial coefficient of intermediate principal stress and continuous rotation of principal stress axes on the stiffness degradation. It is found that the degradation index decreases （or degradation degree increases） significantly with increasing initial orientation angle of the major principal stress and initial ratio of deviatoric stress. Compared with the effects of the initial orientation angle of the major principal stress and initial ratio of deviatoric stress, the effect of initial coefficient of intermediate principal stress is less evident and this trend is more clearly reflected by the results of the cyclic torsional shear tests than those of the cyclic coupling shear tests. At the same cycle number, the degradation index obtained from the cyclic torsional shear test is higher than that from the cyclic coupling shear test. The main reason is that the continuous rotation in principal stress directions during cyclic coupling shear damages the original structure of the soil more than the cyclic torsional shear does.Based on a series of experiments, a mathematical model for stiffness degradation is proposed and the relevant parameters are determined.
基金Project (2007CB714200) supported by National Basic Research Program of ChinaProject (90715018) supported by Key Research Project of National Natural Science Foundation of China
文摘A series of dynamic behavior tests on Nanjing flake-shaped fine sand were performed by using the WFI cyclic triaxial apparatus made in England. The dynamic behaviors of Nanjing flake-shaped fine sand under different static deviator stress levels and cyclic stress ratios were studied. Through comparing the effective stress path under cyclic loading with static loading, the processes of liquefaction of saturated Nanjing flake-shaped fine sand with development of dynamic pore-water pressure, including the initial compact state, compression state and dilative state, were investigated. The variation of the shear stiffness with the number of cycles and cyclic strain was investigated by analyzing the secant shear modulus in each unload-reload loop of dynamic stress-strain relationship. And by means of the exponential function, the empirical equations of the relationship between secant shear modulus Gsec, shear modulus ratio Gsec/Gmax and cyclic strain ε were established based on series of test results. The results show that according to different combinations of static deviator stress and cyclic stress, two kinds of failure patterns with deviator stress reversal or no deviator stress reversal are observed in the samples tested in this series, including cyclic mobility and the failure of accumulation residual strain. In addition, the degradation of dynamic shear modulus is due to the development of vibration pore-water pressure and it is observed that the shear modulus reduces with the progressive number of cycles.
