High-speed performance self-powered short wave ultraviolet radiation detectors based onκ(ε)-Ga_(2)O_(3)

High-speed solar-blind short wavelength ultraviolet radiation detectors based onκ(ε)-Ga_(2)O_(3)layers with Pt contacts were demonstrated and their properties were studied in detail.Theκ(ε)-Ga_(2)O_(3)layers were deposited by the halide vapor phase epitaxy on patterned GaN templates with sapphire substrates.The spectral dependencies of the photoelectric properties of struc-tures were analyzed in the wavelength interval 200-370 nm.The maximum photo to dark current ratio,responsivity,detectiv-ity and external quantum efficiency of structures were determined as:180.86 arb.un.,3.57 A/W,1.78×10^(12) Hz^(0.5)∙cm·W^(-1) and 2193.6%,respectively,at a wavelength of 200 nm and an applied voltage of 1 V.The enhancement of the photoresponse was caused by the decrease in the Schottky barrier at the Pt/κ(ε)-Ga_(2)O_(3)interface under ultraviolet exposure.The detectors demon-strated could functionalize in self-powered mode due to built-in electric field at the Pt/κ(ε)-Ga_(2)O_(3)interface.The responsivity and external quantum efficiency of the structures at a wavelength of 254 nm and zero applied voltage were 0.9 mA/W and 0.46%,respectively.The rise and decay times in self-powered mode did not exceed 100 ms.

Low-noise and low-power pixel sensor chip for gas pixel detectors

Topmetal-M2 is a large-area pixel sensor chip fabricated using the GSMC 130 nm CMOS process in 2021.The pixel array of Topmetal-M2 consists of pixels of 400 rows×512 columns with a pixel pitch of 45μm×45μm.The array is divided into 16 subarrays,with pixels of 400 rows×32 columns per subarray.Each pixel incorporates two charge sensors:a diode sensor and a Topmetal sensor.The in-pixel circuit primarily consists of a charge-sensitive amplifier for energy measurements,a discriminator with a peak-holding circuit,and a time-to-amplitude converter for time-of-arrival measurements.The pixel of Topmetal-M2 has a charge input range of~0-3 k e-,a voltage output range of~0-180 mV,and a charge-voltage conversion gain of~59.56μV∕e-.The average equivalent noise charge of Topmetal-M2,which includes the readout electronic system noise,is~43.45 e-.In the scanning mode,the time resolution of Topmetal-M2 is 1 LSB=1.25μs,and the precision is^()7.41μs.At an operating voltage of 1.5 V,Topmetal-M2 has a power consumption of~49 mW∕cm~2.In this article,we provide a comprehensive overview of the chip architecture,pixel working principles,and functional behavior of Topmetal-M2.Furthermore,we present the results of preliminary tests conducted on Topmetal-M2,namely,alpha-particle and soft X-ray tests.

Flexibility potential of Cs_(2)BX_(6)(B=Hf,Sn,Pt,Zr,Ti;X=I,Br,Cl)with application in photovoltaic devices and radiation detectors

As interest in double perovskites is growing,especially in applications like photovoltaic devices,understanding their mechanical properties is vital for device durability.Despite extensive exploration of structure and optical properties,research on mechanical aspects is limited.This article builds a vacancyordered double perovskite model,employing first-principles calculations to analyze mechanical,bonding,electronic,and optical properties.Results show Cs_(2)Hfl_(6),Cs_(2)SnBr_(6),Cs_(2)SnI_(6),and Cs_(2)PtBr_(6)have Young's moduli below 13 GPa,indicating flexibility.Geometric parameters explain flexibility variations with the changes of B and X site composition.Bonding characteristic exploration reveals the influence of B and X site electronegativity on mechanical strength.Cs_(2)SnBr_(6)and Cs_(2)PtBr_(6)are suitable for solar cells,while Cs_(2)HfI_(6)and Cs_(2)TiCl_(6)show potential for semi-transparent solar cells.Optical property calculations highlight the high light absorption coefficients of up to 3.5×10^(5) cm^(-1)for Cs_(2)HfI_(6)and Cs_(2)TiCl_(6).Solar cell simulation shows Cs_(2)PtBr_(6)achieves 22.4%of conversion effciency.Cs_(2)ZrCl_(6)holds promise for ionizing radiation detection with its 3.68 eV bandgap and high absorption coefficient.Vacancy-ordered double perovskites offer superior flexibility,providing valuable insights for designing stable and flexible devices.This understanding enhances the development of functional devices based on these perovskites,especially for applications requiring high stability and flexibility.

Self-powered UVC detectors based on α-Ga_(2)O_(3) with enchanted speed performance

Detectors were developed for detecting irradiation in the short-wavelength ultraviolet(UVC)interval using high-quality single-crystallineα-Ga_(2)O_(3) films with Pt interdigital contacts.The films ofα-Ga_(2)O_(3) were grown on planar sapphire substrates with c-plane orientation using halide vapor phase epitaxy.The spectral dependencies of the photo to dark current ratio,responsivity,external quantum efficiency and detectivity of the structures were investigated in the wavelength interval of 200−370 nm.The maximum of photo to dark current ratio,responsivity,external quantum efficiency,and detectivity of the structures were 1.16×10^(4) arb.un.,30.6 A/W,1.65×10^(4)%,and 6.95×10^(15) Hz^(0.5)·cm/W at a wavelength of 230 nm and an applied voltage of 1 V.The high values of photoelectric properties were due to the internal enhancement of the photoresponse associated with strong hole trapping.Theα-Ga_(2)O_(3) film-based UVC detectors can function in self-powered operation mode due to the built-in electric field at the Pt/α-Ga_(2)O_(3) interfaces.At a wavelength of 254 nm and zero applied voltage,the structures exhibit a responsivity of 0.13 mA/W and an external quantum efficiency of 6.2×10^(−2)%.The UVC detectors based on theα-Ga_(2)O_(3) films demonstrate high-speed performance with a rise time of 18 ms in self-powered mode.

FPGA implementation of 500-MHz high-count-rate high-time-resolution real-time digital neutron-gamma discrimination for fast liquid detectors

Fast neutron flux measurements with high count rates and high time resolution have important applications in equipment such as tokamaks.In this study,real-time neutron and gamma discrimination was implemented on a self-developed 500-Msps,12-bit digitizer,and the neutron and gamma spectra were calculated directly on an FPGA.A fast neutron flux measurement system with BC-501A and EJ-309 liquid scintillator detectors was developed and a fast neutron measurement experiment was successfully performed on the HL-2 M tokamak at the Southwestern Institute of Physics,China.The experimental results demonstrated that the system obtained the neutron and gamma spectra with a time accuracy of 1 ms.At count rates of up to 1 Mcps,the figure of merit was greater than 1.05 for energies between 50 keV and 2.8 MeV.

Structural design of mid-infrared waveguide detectors based on InAs/GaAsSb superlattice

In the realm of near-infrared spectroscopy,the detection of molecules has been achieved using on-chip waveguides and resonators.In the mid-infrared band,the integration and sensitivity of chemical sensing chips are often constrained by the reliance on off-chip light sources and detectors.In this study,we demonstrate an InAs/GaAsSb superlattice mid-infrared waveguide integrated detector.The GaAsSb waveguide layer and the InAs/GaAsSb superlattice absorbing layer are connected through evanescent coupling,facilitating efficient and highquality detection of mid-infrared light with minimal loss.We conducted a simulation to analyze the photoelectric characteristics of the device.Additionally,we investigated the factors that affect the integration of the InAs/GaAs⁃Sb superlattice photodetector and the GaAsSb waveguide.Optimal thicknesses and lengths for the absorption lay⁃er are determined.When the absorption layer has a thickness of 0.3μm and a length of 50μm,the noise equiva⁃lent power reaches its minimum value,and the quantum efficiency can achieve a value of 68.9%.The utilization of waveguide detectors constructed with Ⅲ-Ⅴ materials offers a more convenient means of integrating mid-infra⁃red light sources and achieving photoelectric detection chips.

Effect of multiple coulomb scattering on the beam tests of silicon pixel detectors

In the research and development of new silicon pixel detectors,a collimated monoenergetic charged-particle test beam equipped with a high-resolution pixel-beam telescope is crucial for prototype verification and performance evaluation.When the beam energy is low,the effect of multiple Coulomb scattering on the measured resolution of the Device Under Test(DUT)must be considered to accurately evaluate the performance of the pixel chips and detectors.This study aimed to investigate the effect of multiple Coulomb scattering on the measured resolution,particularly at low beam energies.Simulations were conducted using Allpix^(2) to study the effects of multiple Coulomb scattering under different beam energies,material budgets,and telescope layouts.The simulations also provided the minimum energy at which the effect of multiple Coulomb scattering could be ignored.Compared with the results of a five-layer detector system tested with an electron beam at DESY,the simulation results were consistent with the beam test results,confirming the reliability of the simulations.

Countermeasure against blinding attack for single-photon detectors in quantum key distribution

Quantum key distribution(QKD),rooted in quantum mechanics,offers information-theoretic security.However,practi-cal systems open security threats due to imperfections,notably bright-light blinding attacks targeting single-photon detectors.Here,we propose a concise,robust defense strategy for protecting single-photon detectors in QKD systems against blinding attacks.Our strategy uses a dual approach:detecting the bias current of the avalanche photodiode(APD)to defend against con-tinuous-wave blinding attacks,and monitoring the avalanche amplitude to protect against pulsed blinding attacks.By integrat-ing these two branches,the proposed solution effectively identifies and mitigates a wide range of bright light injection attempts,significantly enhancing the resilience of QKD systems against various bright-light blinding attacks.This method forti-fies the safeguards of quantum communications and offers a crucial contribution to the field of quantum information security.

Metal-Halide Perovskite Submicrometer-Thick Films for Ultra-Stable Self-Powered Direct X-Ray Detectors

Metal-halide perovskites are revolutionizing the world of X-ray detectors,due to the development of sensitive,fast,and cost-effective devices.Self-powered operation,ensuring portability and low power consumption,has also been recently demonstrated in both bulk materials and thin films.However,the signal stability and repeatability under continuous X-ray exposure has only been tested up to a few hours,often reporting degradation of the detection performance.Here it is shown that self-powered direct X-ray detectors,fabricated starting from a FAPbBr_(3)submicrometer-thick film deposition onto a mesoporous TiO_(2)scaffold,can withstand a 26-day uninterrupted X-ray exposure with negligible signal loss,demonstrating ultra-high operational stability and excellent repeatability.No structural modification is observed after irradiation with a total ionizing dose of almost 200 Gy,revealing an unexpectedly high radiation hardness for a metal-halide perovskite thin film.In addition,trap-assisted photoconductive gain enabled the device to achieve a record bulk sensitivity of 7.28 C Gy^(−1)cm^(−3)at 0 V,an unprecedented value in the field of thin-film-based photoconductors and photodiodes for“hard”X-rays.Finally,prototypal validation under the X-ray beam produced by a medical linear accelerator for cancer treatment is also introduced.

In-flight Energy Calibration of the GECAM Gamma-ray Detectors

The Gravitational wave high-energy Electromagnetic Counterpart All-sky Monitor(GECAM)mission is designed to monitor the Gamma-Ray Bursts(GRBs)associated with gravitational waves and other high-energy transient sources.The mission consists of two microsatellites which are planned to operate at the opposite sides of the Earth.Each GECAM satellite could detect and localize GRBs in about 8 keV-5 MeV with its 25 Gamma-Ray Detectors(GRDs).In this work,we report the in-flight energy calibration of GRDs using the characteristic gamma-ray lines in the background spectra,and show their performance evolution during the commissioning phase.Besides,a preliminary cross-calibration of energy response with Fermi GBM data is also presented,validating the energy response of GRDs.

基于InVEST&GEO-detectors模型的会仙湿地生境质量变化及影响因素研究

喀斯特湿地是广泛分布在喀斯特地区的一种特殊的湿地类型,其生态地位举足轻重,探索喀斯特湿地生境质量变化的影响因素对喀斯特地区生态建设具有重要的意义。本文基于会仙湿地保护区2000和2020年的土地利用数据,通过InVEST模型评估会仙湿地保护区的生境质量,利用地理探测器探测影响会仙湿地保护区生境质量变化的自然和人为因素。研究结果表明:1)研究区2000至2020年建设用地明显扩张,草地和水体显著减少;2)会仙湿地保护区生境质量总体呈现下降的趋势,生境退化度有所上升,生境质量较差的区域主要集中在研究区的北部、中部和东北部;3)地理探测器识别出会仙湿地保护区生境质量空间变化受自然和人为因子的综合作用,主导影响因子是GDP(q为0.135),其次为夜间灯光指数(DMSP)(q为0.053);交互作用探测结果表明,各因子对生境质量影响呈现出双因子增强效果。研究结果有助于揭示会仙湿地保护区生境质量的时空演变过程,可针对会仙湿地生态建设的问题提出可行的应对策略。

Data-driven simultaneous vertex and energy reconstruction for large liquid scintillator detectors

High-precision vertex and energy reconstruction are crucial for large liquid scintillator detectors such as that at the Jiangmen Underground Neutrino Observatory(JUNO),especially for the determination of neutrino mass ordering by analyzing the energy spectrum of reactor neutrinos.This paper presents a data-driven method to obtain a more realistic and accurate expected PMT response of positron events in JUNO and develops a simultaneous vertex and energy reconstruction method that combines the charge and time information of PMTs.For the JUNO detector,the impact of the vertex inaccuracy on the energy resolution is approximately 0.6%.

Twin model-based fault detection and tolerance approach for in-core self-powered neutron detectors

The in-core self-powered neutron detector(SPND)acts as a key measuring device for the monitoring of parameters and evaluation of the operating conditions of nuclear reactors.Prompt detection and tolerance of faulty SPNDs are indispensable for reliable reactor management.To completely extract the correlated state information of SPNDs,we constructed a twin model based on a generalized regression neural network(GRNN)that represents the common relationships among overall signals.Faulty SPNDs were determined because of the functional concordance of the twin model and real monitoring sys-tems,which calculated the error probability distribution between the model outputs and real values.Fault detection follows a tolerance phase to reinforce the stability of the twin model in the case of massive failures.A weighted K-nearest neighbor model was employed to reasonably reconstruct the values of the faulty signals and guarantee data purity.The experimental evaluation of the proposed method showed promising results,with excellent output consistency and high detection accuracy for both single-and multiple-point faulty SPNDs.For unexpected excessive failures,the proposed tolerance approach can efficiently repair fault behaviors and enhance the prediction performance of the twin model.

Image Captioning Using Detectors and Swarm Based Learning Approach for Word Embedding Vectors

IC(Image Captioning)is a crucial part of Visual Data Processing and aims at understanding for providing captions that verbalize an image’s important elements.However,in existing works,because of the complexity in images,neglecting major relation between the object in an image,poor quality image,labelling it remains a big problem for researchers.Hence,the main objective of this work attempts to overcome these challenges by proposing a novel framework for IC.So in this research work the main contribution deals with the framework consists of three phases that is image understanding,textual understanding and decoding.Initially,the image understanding phase is initiated with image pre-pro-cessing to enhance image quality.Thereafter,object has been detected using IYV3MMDs(Improved YoloV3 Multishot Multibox Detectors)in order to relate the interrelation between the image and the object,and then it is followed by MBFOCNNs(Modified Bacterial Foraging Optimization in Convolution Neural Networks),which encodes and providesfinal feature vectors.Secondly,the tex-tual understanding phase is performed based on an image which is initiated with preprocessing of text where unwanted words,phrases,punctuations are removed in order to provide a healthy text.It is then followed by MGloVEs(Modified Glo-bal Vectors for Word Representation),which provides a word embedding of fea-tures with the highest priority towards the object present in an image.Finally,the decoding phase has been performed,which decodes the image whether it may be a normal or complex scene image and provides an accurate text by its learning ability using MDAA(Modified Deliberate Adaptive Attention).The experimental outcome of this work shows better accuracy of shows 96.24%when compared to existing and similar methods while generating captions for images.

Performance optimization of scintillator neutron detectors for EMD in CSNS

Chinese Spallation Neutron Source(CSNS) has successfully produced its first neutron beam in 28th August 2017. It has been running steadily from March, 2018. According to the construction plan, the engineering materials diffractometer(EMD) will be installed between 2019–2023. This instrument requires the neutron detectors with the cover area near3 m2in two 90° neutron diffraction angle positions, the neutron detecting efficiency is better than 40%@1A, and the spatial resolution is better than 4 mm×200 mm in horizontal and vertical directions respectively. We have developed a onedimensional position-sensitive neutron detector based on the oblique6Li F/Zn S(Ag) scintillators, wavelength shifting fibers,and Si PMs(silicon photomultipliers) readout. The inhomogeneity of the neutron detection efficiency between each pixel and each detector module, which caused by the inconsistency of the wave-length shifting fibers in collecting scintillation photons, needs to be mitigated before the installation. A performance optimization experiment of the detector modules was carried out on the BL20(beam line 20) of CSNS. Using water sample, the neutron beam with Φ5 mm exit hole was dispersed related evenly into the forward space. According to the neutron counts of each pixel of the detector module, the readout electronics threshold of each pixel is adjusted. Compared with the unadjusted detector module, the inhomogeneity of the detection efficiency for the adjusted one has been improved from 69% to 90%. The test result of the diffraction peak of the standard sample Si showed that the adjusted detector module works well.

The Accuracy Levels of Vehicle Detectors Commonly Used in Korea Based on the Results of Quality Certification Test

The Ministry of Land, Infrastructure and Transport of Korea introduced the ITS system performance evaluation about six and a half years ago. The main purpose is to make sure that accurate and reliable real-time traffic data are collected from the ITS system installed. There are three types of performance evaluations, which are Quality Certification Test, Pre-Delivery Test and Periodic Check in Operation. In this paper the accuracy levels of vehicle detectors commonly used in Korea are analyzed based on the results of quality certification tests conducted during 2008-2012. The test items consist of volume, speed and occupancy. The analysis shows that loop detectors have the best levels of accuracy in all three test items and their levels of accuracy have been steady. Video image detectors do not have so good levels of accuracy as loop detectors, but the levels of accuracy have improved as time passes. Radar detectors do not have good levels of accuracy. However, their levels of accuracy have improved as time passes. The last vehicle detectors, geomagnetism detectors have the worst accuracy in the occupancy item.

中国县域数字乡村发展的空间格局及驱动因素研究

基于北京大学新农村发展研究院公布的2018年中国1880个县域数字乡村指数数据,采用探索性空间数据分析、冷热点分析和地理探测器等方法,考察中国县域数字乡村发展的空间格局及其驱动因素。结果表明:1)中国县域数字乡村发展水平呈现明显的“梯度化”特征,数字乡村发展水平由东部向西部逐渐递减,数字乡村在长三角地区呈“片状分布”,而在西部地区和东北地区呈“点状分布”。2)中国县域数字乡村发展呈现明显的空间集聚特征,在经济发展水平较高、网络基础设施较为完善的长三角地区形成“高-高”集聚。数字乡村发展呈现次热点区和热点区围绕高热点区集聚的“中心-外围”结构形态。在热点区与冷点区之间形成“T”字形狭长地带,将热点区与冷点区分隔开。3)中国县域数字乡村发展的总体基尼系数为0.0359,其中数字乡村的区域间差距是数字乡村发展总体差异的主要来源。4)产业经济、人口教育、财政金融和基础设施的空间分异特征对数字乡村空间分布具有较强的影响。

秦岭北麓沣河流域矿区生境质量的时空演变及驱动因素分析

秦岭是中国的“中央水塔”,研究秦岭北麓矿山生境质量的时空演变特征对区域生态保护和可持续发展意义重大。为了评估小流域背景下人类活动对矿山生态环境的影响,该研究针对沣河流域内的重点工程祥峪铁矿区,基于遥感影像提取其1985、2002、2010年和2022年土地利用变化,结合InVEST(integrated valuation of ecosystem services and tradeoffs)模型和地理探测器定量分析该矿区生境质量变化与驱动因素。结果表明:祥峪铁矿区的土地利用变化主要由旱地逐步转变为林地和工业用地,疏林地转入面积达到18245505.71 m^(2),退耕还林还草工程取得显著成效;祥峪铁矿区生境质量指数由0.50下降为0.49,标准差由0.06增加为0.09,说明生境质量有所下降,空间差异不断扩大,区域整体平均生境退化度降低,但工业用地迅速扩张对周边林地产生持续影响;生境质量变化是自然因素和人文因素共同作用的结果,其中,土地利用变化是造成生态环境脆弱的主要原因,对生境质量变化的解释力达到0.82。该研究可为分析其他类似矿区生态环境演变,推动景观格局的优化和生态文明建设提供科学参考。

基于透镜阵列多元聚焦的连续晶体三维位置灵敏探测器设计和仿真

连续晶体闪烁体探测器可以实现γ射线作用点的三维位置定位。本文提出一种新的探测器结构,引入透镜阵列实现作用点定位。探测器采集多元聚焦图像,从而改变对连续晶体闪烁光分布探测的需求。文中建立连续晶体、透镜阵列和光子计数器阵列的模型进行模拟研究,建立多元聚焦的光路反演重建算法定位γ射线作用点的三维位置。通过重建结果分析评估基于透镜阵列的连续晶体探测器性能,这种结构具有较好的定位能力和位置分辨。对于尺寸为48 mm×48 mm×45 mm的硅酸钇镥(LYSO)闪烁晶体,实现了xy平面位置分辨优于1.54 mm,z方向位置分辨优于3.13 mm。基于连续晶体和透镜阵列结构的探测器还可对多作用点的情形进行重建,分析三组选定位置的重建结果,该结构对双作用点定位具有可行性。

集成芯片硅微条探测器电子读出系统设计

设计了基于VATA460.3专用集成芯片(ASIC)的多通道、低功耗带触发硅微条探测器读出系统,该系统实现了共32路粒子入射信息读出。测试结果表明:该系统各通道基线稳定,等效噪声水平均低于0.17 fC,动态范围可达90 fC。