A Comparative Overview of Indirect Field Oriented Control (IFOC) and Deadbeat-Direct Torque and Flux Control (DB-DTFC) for AC Motor Drives

Indirect field oriented control(IFOC)has become a widely adopted solution for AC motor drives.Standard IFOC controls torque and rotor flux linkage via q-and d-axis current.Alternatively,deadbeat-direct torque and flux control(DB-DTFC)has emerged as a promising motor control strategy for the future,which manipulates Volt-sec.vector directly.Air-gap torque and stator flux linkage are decoupled and independently controlled over each switching period.Stator flux linkage is used as a separated degree-of-freedom to manipulate losses dynamically without compromising torque dynamics and torque ripple.In voltage-limited operations,direct selection of Volt-sec.allows DB-DTFC to fully utilize the dc bus voltage and produce fast torque.A single control law is used over a wide speed range.This paper aims to provide a comparative overview of the two motor controls regarding their sensitivity to parameters,current-and voltage-limited operation,loss manipulation,and torque ripple during signal injection.Based on the comparison,the ultimate objective is to demonstrate the opportunities and remaining challenges in DB-DTFC.

Driving and Braking Control of PM Synchronous Motor Based on Low-resolution Hall Sensor for Battery Electric Vehicle

Resolvers are normally employed for rotor positioning in motors for electric vehicles, but resolvers are expensive and vulnerable to vibrations. Hall sensors have the advantages of low cost and high reliability, but the positioning accuracy is low. Motors with Hall sensors are typically controlled by six-step commutation algorithm, which brings high torque ripple. This paper studies the high-performance driving and braking control of the in-wheel permanent magnetic synchronous motor （PMSM） based on low-resolution Hall sensors. Field oriented control （FOC） based on Hall-effect sensors is developed to reduce the torque ripple. The positioning accuracy of the Hall sensors is improved by interpolation between two consecutive Hall signals using the estimated motor speed. The position error from the misalignment of the Hall sensors is compensated by the precise calibration of Hall transition timing. The braking control algorithms based on six-step commutation and FOC are studied. Two variants of the six-step commutation braking control, namely, half-bridge commutation and full-bridge commutation, are discussed and compared, which shows that the full-bridge commutation could better explore the potential of the back electro-motive forces （EMF）, thus can deliver higher efficiency and smaller current ripple. The FOC braking is analyzed with the phasor diagrams. At a given motor speed, the motor turns from the regenerative braking mode into the plug braking mode if the braking torque exceeds a certain limit, which is proportional to the motor speed. Tests in the dynamometer show that a smooth control could be realized by FOC driving control and the highest efficiency and the smallest current ripple could be achieved by FOC braking control, compared to six-step commutation braking control. Therefore, FOC braking is selected as the braking control algorithm for electric vehicles. The proposed research ensures a good motor control performance while maintaining low cost and high reliability.

Genetic algorithm tuned PI controller on PMSM simplified vector control

A simple control structure in servo system is occasionally needed for simple industrial application which precise and high control performance is not exessively important so that the cost production can be reduced efficiently. Simplified vector control, which has simple control structure, is utilized as the permanent magnet synchronous motor control algorithm and genetic algorithm is used to tune three PI controllers used in simplified vector control. The control performance is obtained from simulation and investigated to verify the feasibility of the algorithm to be applied in the real application. Simulation results show that the speed and torque responses of the system in both continuous time and discrete time can achieve good performances. Furthermore, simplified vector control combined with genetic algorithm has a similar perfofmance with conventional field oriented control algorithm and possible to be realized into the real simple application in the future.

PSO Based Controlled Six-phase Grid Connected Induction Generator for Wind Energy Generation

This paper deals a detailed performance investigation of asymmetrical six-phase grid connected induction generator(GCIG)in two proposed configurations in variable speed operation.During the system development,regulation of DC-link voltage has been proposed using particle swarm optimization(PSO)based PI controller,ensuring the power flow to utility grid through back to back converters.The closed loop operation of asymmetrical six-phase GCIG using indirect field oriented control in different configurations has been carried out in Matlab/Simulink environment.Analytical results have been verified using real time test results on virtual platform of Typhoon HIL supported with some experimental validation.

Torque-based Optimal Acceleration Control for Electric Vehicle

The existing research of the acceleration control mainly focuses on an optimization of the velocity trajectory with respect to a criterion formulation that weights acceleration time and fuel consumption. The minimum-fuel acceleration problem in conventional vehicle has been solved by Pontryagin＇s maximum principle and dynamic programming algorithm, respectively. The acceleration control with minimum energy consumption for battery electric vehicle（EV） has not been reported. In this paper, the permanent magnet synchronous motor（PMSM） is controlled by the field oriented control（FOC） method and the electric drive system for the EV（including the PMSM, the inverter and the battery） is modeled to favor over a detailed consumption map. The analytical algorithm is proposed to analyze the optimal acceleration control and the optimal torque versus speed curve in the acceleration process is obtained. Considering the acceleration time, a penalty function is introduced to realize a fast vehicle speed tracking. The optimal acceleration control is also addressed with dynamic programming（DP）. This method can solve the optimal acceleration problem with precise time constraint, but it consumes a large amount of computation time. The EV used in simulation and experiment is a four-wheel hub motor drive electric vehicle. The simulation and experimental results show that the required battery energy has little difference between the acceleration control solved by analytical algorithm and that solved by DP, and is greatly reduced comparing with the constant pedal opening acceleration. The proposed analytical and DP algorithms can minimize the energy consumption in EV＇s acceleration process and the analytical algorithm is easy to be implemented in real-time control.

Starting Control of Free Piston Stirling Linear Generator System Based on FOC

Aiming at the problem of poor system dynamic performance caused by low parameter matching in the coordinated control of Stirling engine and linear generator in the starting stage control of free piston Stirling linear generator system,a joint control method of free piston Stirling permanent magnet synchronous linear generator system based on field orientation control is proposed,based on the theoretical derivation of the mathematical model of the system and the principle of controller parameters setting,the simulation experiments of the system starting stage under several Stirling engine working conditions are carried out under simulation.The experimental results show that the stability and rapidity of the system are improved,and the dynamic response speed of generator parameters under different working conditions is accelerated,what fully verifies the correctness and effectiveness of the method.It provides an effective way to improve the control performance of the system and stabilize the power generation operation.

Continuous on-line adaptation of the rotor time constant in FOC induction machine system

Rotor time constant is an important parameter for the indirect lleld oraentateO control of mauc- tion motor. Incorrect rotor tittle constant value will cause the flux observer generating a wrong angu- lar orientation of the rotor field. A new approach serves for rotor time constant on-line adaptation by setting the stator current to be zero for a short period. A smooth eorrector is designed to prevent ab- normal detection result from making adaptation. Impact of zero current duration on detection error and rotor speed is analyzed by experiments.

Robust Sliding Mode Control Using Adaptive Switching Gain for Induction Motors

A robust sliding mode approach combined with a field oriented control （FOC） for induction motor （IM） speed control is presented. The proposed sliding mode control （SMC） design uses an adaptive switching gain and an integrator. This approach guarantees the same robustness and dynamic performance of traditional SMC algorithms. And at the same time, it attenuates the chattering phenomenon, which is the main drawback in actual implementation of this technique. This approach is insensitive to uncertainties and permits to decrease the requirement for the bound of these uncertainties. The stability and robustness of the closed- loop system are proven analytically using the Lyapunov synthesis approach. The proposed method attenuates the effect of both uncertainties and external disturbances. Experimental results are presented to validate the effectiveness and the good performance of the developed method.

Overview of Advanced Control Strategies for Electric Machines

Control strategies play a key role for operation of electric machines,which would directly affect the whole system performance.In fact,different control strategies have been executed and explored for electric machines,which bring great impacts to industrial development and human society.This paper investigates and discusses the advantages control strategies for electric machines,including the field oriented control(FOC),direct torque control(DTC),finite control set model predictive control(FCS-MPC),sensorless control,and fault tolerant control(FTC).The corresponding control principles,control targets,fundamental approaches,advanced approaches,methodologies,merits and shortcomings are revealed and analyzed in detail.

Overview of Model Predictive Control for Induction Motor Drives

Model predictive control(MPC)has attracted widespread attention in both academic and industry communities due to its merits of intuitive concept,quick dynamic response,multi-variable control,ability to handle various nonlinear constraints,and so on.It is considered a powerful alternative to field oriented control(FOC)and direct torque control(DTC)in high performance AC motor drives.Compared to FOC,MPC eliminates the use of internal current control loops and modulation block,hence featuring very quick dynamic response.Compared to DTC,MPC uses a cost function rather than a heuristic switching table to select the best voltage vector,producing better steady state performance.In spite of the merits above,MPC also presents some drawbacks such as high computational burden,nontrivial weighting factor tuning,high sampling frequency,variable switching frequency,model/parameter dependence and relatively high steady ripples in torque and stator flux.This paper presents the state of the art of MPC in high performance induction motor(IM)drives,and in particular the progress on solving the drawbacks of conventional MPC.Finally,one of the improved MPC is compared to FOC to validate its superiority.It is shown that the improved MPC has great potential in the future high performance AC motor drives.

Classical state feedback controller for nonlinear systems using mean value theorem： closed Ioop-FOC of PMSM motor application

The problem of state feedback controllers for a class of Takagi-Sugeno （T-S） Lipschitz nonlinear systems is investigated. A simple systematic and useful synthesis method is proposed based on the use of the differential mean value theorem （DMVT） and convex theory. The proposed design approach is based on the mean value theorem （MVT） to express the nonlinear error dynamics as a convex combination of known matrices with time varying coefficients as linear parameter varying （LPV） systems. Using the Lyapunov theory, stability conditions are obtained and expressed in terms of linear matrix inequalities （LMIs）. The controller gains are then obtained by solving linear matrix inequalities. The effectiveness of the proposed approach for closed loop-field oriented control （CL-FOC） of permanent magnet synchronous machine （PMSM） drives is demonstrated through an illustrative simulation for the proof of these approaches. Furthermore, an extension for controller design with parameter uncertainties and perturbation performance is discussed.