Mechanical behaviours of bedded sandstone under hydromechanical coupling

The combination of the dipping effect and hydromechanical(H-M)coupling effect can easily lead to water inrush disasters in water-rich roadways with different dip angles in coal mines.Therefore,H-M coupling tests of bedded sandstones under identical osmotic pressure and various confining pressures were conducted.Then,the evolution curves of stress-strain,permeability and damage,macro-and mesoscopic failure characteristics were obtained.Subsequently,the mechanical behaviour was characterized,and finally the failure mechanism was revealed.The results showed that:(1)The failure of the sandstone with the bedding angle of 45°or 60°was the structure-dominant type,while that with the bedding angle of 0°,30°or 90°was the force-dominant type.(2)When the bedding angle was in the range of(0°,30°)or(45°,90°),the confining pressure played a dominant role in influencing the peak strength.However,withinβ∈(30°,45°),the bedding effect played a dominant role in the peak strength.(3)With the increase in bedding angle,the cohesion increased first,then decreased and finally increased,while the internal friction angle was the opposite.(4)When the bedding angle was 0°or 30°,the“water wedging”effect and the“bedding buckling”effect would lead to the forking or converging shear failure.When the bedding angle was 45°or 60°,the sliding friction effect would lead to the shear slipping failure.When the bedding angle was 90°,the combination of the“bedding buckling”effect and shear effect would lead to the mixed tension-shear failure.The above conclusions obtained are helpful for the prevention of water inrush disasters in water-rich roadways with different dips in coal mines.

Mechanical behavior of sandstone during post-peak cyclic loading and unloading under hydromechanical coupling

This paper investigates mechanical behaviours of sandstone during post-peak cyclic loading and unloading subjected to hydromechanical coupling effect, confirming the peak and residual strengths reduction laws of sandstone with water pressure, and revealing the influence of water pressure on the upper limit stress and deformation characteristics of sandstone during post-peak cyclic loading and unloading.Regarding the rock strength, the experimental study confirms that the peak strength σ_(p) and residual strength σ_(r) decrease as water pressure P increases. Especially, the normalized strength parameters σ_(p)/σ_(pk) and σ_(r)/σ_(re) was negatively and linearly correlated with the P/σ_(3). Moreover, the Hoek-Brown strength criterion can be applied to describe the relationship between effective peak strength and effective confining stress. During post-peak cyclic loading and unloading, both the upper limit stress σ_(p(i)) and crack damage threshold stress σ_(cd(i)) of each cycle tend to decrease with the increasing cycle number. A hysteresis loop exists among the loading and unloading stress–strain curves, indicating the unloading deformation modulus E_(unload) is larger than the loading deformation modulus E_(load). Based on experimental results,a post-peak strength prediction model related to water pressure and plastic shear strain is established.

Groundwater flow through fractured rocks and seepage control in geotechnical engineering: Theories and practices

Groundwater flow through fractured rocks has been recognized as an important issue in many geotechnical engineering practices.Several key aspects of fundamental mechanisms,numerical modeling and engineering applications of flow in fractured rocks are discussed.First,the microscopic mechanisms of fluid flow in fractured rocks,especially under the complex conditions of non-Darcian flow,multiphase flow,rock dissolution,and particle transport,have been revealed through a com-bined effort of visualized experiments and theoretical analysis.Then,laboratory and field methods of characterizing hydraulic properties(e.g.intrinsic permeability,inertial permeability,and unsaturated flow parameters)of fractured rocks in different flow regimes have been proposed.Subsequently,high-performance numerical simulation approaches for large-scale modeling of groundwater flow in frac-tured rocks and aquifers have been developed.Numerical procedures for optimization design of seepage control systems in various settings have also been proposed.Mechanisms of coupled hydro-mechanical processes and control of flow-induced deformation have been discussed.Finally,three case studies are presented to illustrate the applications of the improved theoretical understanding,characterization methods,modeling approaches,and seepage and deformation control strategies to geotechnical engi-neering projects.

Assessments of the effects of various fracture surface morphology on single fracture flow: A review

Natural rock joint permeability deviates from the classic fluid flow governing equations due to the inher-ent fracture surface roughness(i.e.,contact points,spatial correlation,matching,varying aperture,iso-lated voids,infilling material,tortuosity and channellings)and engineering disturbance such as excavations.To improve the accuracy of fracture permeability evaluation,many efforts have been made in analytical,experimental,and numerical methods.This study reviews the modified mathematical gov-erning equations of fluid flow and classifies them based on different influencing factors,such as friction factor,aperture,tortuosity,inertia,and various in situ stress effects.Various experimental and simulation techniques for the coupled normal-and shear-stress flow problems were assessed,and their advantages and disadvantages were also analysed.Furthermore,different surface roughness descriptions and their impacts on mechanical and hydraulic behaviours were discussed,followed by the potential research directions for fracture flow problems.

Experimental Research on the Mechanism of Lift Amplification and Vibration Suppression of Lorentz Force

The Lorentz force generated by electromagnetic field on the surface of the cylinder in the electrolyte solution may modify the structure of the flow boundary layer effectively. The transient control process of Lorentz force is investigated experimentally for lift amplification and vibration suppression. The experiments are conducted in a rotating annular tank filled with a low-conducting electrolyte. A cylinder with an electro-magnetic actuator is placed into the electrolyte. The lift force of cylinder is measured using the strain gages attached to a fixed beam, and the flow fields are visualized by the dye markers. The results show that the upper vortex on the cylinder is suppressed, and the wake becomes a line and leans to the lower side under the action of upside Lorentz force while the lower vortex on the cylinder is suppressed and limited in a small region. Therefore, the value of lift increases with the variation of flow field. However, the vortexes on the cylinder are suppressed fully under the action of symmetrical Lorentz force which leads to the suppression of lift oscillation and then the vibration of cylinder are suppressed fully.

Lift Enhancement and Oscillatory Suppression of Vortex-induced Vibration in Shear Flow by Loentz Force

The flow of the weak electrolyte solution can be controlled by Lorentz force achieved with the suitable magnetic and electric fields, and it has the advantages of vortex street suppression, drag reduction, lift enhancement and oscillatory suppression for the flow over a bluff body. The electro-magnetic control of vortex-induced vibration (VIV) of a circular cylinder in the shear flow was investigated numerically in the exponential-polar coordinates attached on the moving cylinder for Re=150. With the effect of background vorticity, the vortex street of VIV cylinder was composed of two parallel rows with an opposite sign of the vortices which inclines toward the lower side and the strength of upper vortex is larger than that of lower vortex. The lift force vibrated periodically with the effect of vortex shedding and the mean value was negative due to the background vorticity. The Lorentz force for controlling the VIV cylinder was classified into the field Lorentz force and the wall Lorentz force. The field Lorentz force suppresses the lift oscillation, and in turn, suppresses the VIV, whereas the wall Lorentz force increases the lift.

Transient Electro-Osmotic and Pressure Driven Flows through a Microannulus

Flow behavior of transient mixed electro-osmotic and pressure driven flows (EOF/PDF) through a microannulus is investigated based on a linearized Poisson-Boltzmann equation and Navier-Stokes equation. A semi-analytical solution of EOF velocity distribution as functions of relevant parameters is derived by Laplace transform method. By numerical computations of inverse Laplace transform, the effects of inner to outer wall zeta potential β, the normalized pressure gradient Ω and the inner to outer radius ratio α on transient EOF velocity are presented.

Transient electro-osmotic and pressure driven flows of two-layer fluids through a slit microchannel

By method of the Laplace transform, this arti- cle presents semi-analytical solutions for transient electro- osmotic and pressure-driven flows （EOF/PDF） of two-layer fluids between microparallel plates. The linearized Poisson- Boltzmann equation and the Cauchy momentum equation have been solved in this article. At the interface, the Maxwell stress is included as the boundary condition. By numerical computations of the inverse Laplace transform, the effects of dielectric constant ratio e, density ratio p, pressure ratio p, viscosity ratioμ of layer II to layer I, interface zeta potential difference △ψ, interface charge density jump Q, the ratios of maximum electro-osmotic velocity to pressure velocity , and the normalized pressure gradient B on transient veloc- ity amplitude are presented.We find the velocity amplitude becomes large with the interface zeta potential difference and becomes small with the increase of the viscosity. The ve- locity will be large with the increases of dielectric constant ratio; the density ratio almost does not influence the EOF ve- locity. Larger interface charge density jump leads to a strong jump of velocity at the interface. Additionally, the effects of the thickness of fluid layers （hi and h2） and pressure gradient on the velocity are also investigated.

Research on Performance of U Separator in Sand and Dust Test System

Sand/dust test is one of the key projects to examine the environmental adaptability of ordnance equipment.In order to decrease the abrasion of test facility caused by the sand/dust particles,the particles contained in the airflowneed to be reclaimed effectively.Amathematical model of Useparator is established.The flowfield and the trajectories of particles inside the separator are obtained using a numerical simulation method,and the separation efficiency and pressure drop of separator with different rows of separate components are also obtained at various flowvelocities.The simulation results indicate that the efficiency of U inertia separator is affected by the flowvelocity evidently,and a reasonably designed separator can meet the requirement of the separation efficiency in particular situation.The results can be use as reference for the design and test of sand/dust separate systems.

An Experiment on Releasing Water from Water Tanks by Xu Youzhen during the Ming Dynasty

In 1453,Xu Youzhen,a scholar-bureaucrat and hydrologist in Ming China,was dispatched to Shandong to find a way to harness the Yellow River.He proposed the opening up of multiple channels to diverge the flood waters.An experiment was conducted to compare the efficiency of releasing water using one large opening with the use of a number of small openings.This experiment proved that opening up multiple channels outperformed the construction of only one,thereby convincing the emperor and officials of the efficacy of this method.Xu’s method for water control proved to be successful in averting a flood that occurred in 1456.

Experimental study and modeling of hydromechanical behavior of concrete fracture

In this study, the hydromechanical behavior of a concrete fracture under coupled compressive and shear stresses was investigated. A special experimental device was designed to create a planar fracture in a cylindrical sample and to carry out different kinds of hydromechanical tests on the fracture. Four series of laboratory tests were performed on an ordinary concrete sample. Hydrostatic compression tests were first conducted to characterize the normal compressibility of the fracture. In the second series, direct shear tests were conducted on the fracture under different normal stresses. The maximal shear stress of the fracture was determined as a function of the normal stress. In the third series, fluid flow tests were carried out in view of characterizing the overall hydraulic conductivity of the fracture as a function of its opening and closure. Shear tests with a constant fluid pressure were finally performed to investigate the influence of fluid pressure on the deformation behavior of concrete fractures. Based on the experimental investigation, an elastoplastic model is proposed. This model takes into account the nonlinear elastic behavior of a fracture under normal compression and the plastic deformation and failure due to shear stress. The model was coupled with the classical Darcy's law to describe the fluid flow along the fracture by considering the variation of permeability with fracture aperture. Numerical results agree with experimental data from various laboratory tests.

Optimized constitutive equation of material property based on inverse modeling for aluminum alloy hydroforming simulation

By using aluminum alloys,the properties of the material in sheet hydroforming were obtained based on the identification of parameters for constitutive models by inverse modeling in which the friction coefficients were also considered in 2D and 3D simulations.With consideration of identified simulation parameters by inverse modeling,some key process parameters including tool dimensions and pre-bulging on the forming processes in sheet hydroforming were investigated and optimized.Based on the optimized parameters,the sheet hydroforming process can be analyzed more accurately to improve the robust design.It proves that the results from simulation based on the identified parameters are in good agreement with those from experiments.

Hydromechanical behavior of unsaturated expansive clay under repetitive loading

Compacted layers of expansive soils are used in different engineering projects,such as subgrades,engineered clay barriers,and buffers for radioactive waste disposal.These layers are exposed to a variety of stresses and wetting conditions during field serviceability.Coupling between hydraulic and mechanical repeated loading provides insight understanding to the induced progressive deformation of expansive clay.This study was conducted to investigate the hydromechanical behavior of unsaturated compacted expansive clay under repeated loadingeunloading(RLU)conditions.Two series of onedimensional(1D)oedometer tests were conducted under controlled matric suction up to 1500 kPa using the axis translation technique(Fredlund soil-water characteristic curve device,SWC-150).The first test series was carried out at different levels of controlled matric suction for non-repeated loading eunloading(NRLU)cycles.RLU cycles were applied in the second test series at different repetitivestress levels and under different levels of matric suction.The results indicated increasing axial wetting strainε_(a)(s),axial swell pressure ss(s),compression index C_(c)(s),and swell index C_(s)(s)with suction reduction.The estimated loadecollapse(LC)curves obtained from NRLU series(LCN)and RLU series(LCR)indicated increasing yield stress sy(s)with increasing suction.This is attributed to the developed apparent cohesion between soil particles,which in turn rigidifies the material response.Applying repetitive loading induced a notable reduction of compression index C_(c)(s)at the same level of suction,whereas swell index C_(s)(s)seems to be independent of repetitive loading.Finally,repetitive loading exceeding initial yield stresses results in plastic hardening and,hence,enlargement of yield stress locus(i.e.LCR curve).

Is Terzaghi's effective stress a stress variable under seepage conditions?

From the continuum mechanics perspective, an attempt was made to clarify the role of Terzaghi's effective stress in the theoretical analysis of saturated soil subjected to seepage. The necessity of performing a coupled hydromechanical analysis to solve the seepage-deformation interaction problem was illustrated by examining the equations of static equilibrium among the effective stress, seepage force, pore-water pressure and total stress. The conceptual definition of stress variable that satisfies the principles of continuum mechanics is applied in the coupled hydromechanical analysis. It is shown that Terzaghi's effective stress is in fact not a stress variable under seepage conditions, and the seepage force acting on the soil skeleton cannot be viewed as a body force. This offers a clue to the underlying cause of a paradox between the real Pascal's hydrostatic state and the hydrostatic state predicted by a class of continuum hydromechanical theories.

OPTIMIZATION OF SHEET METAL FORMING PROCESSES USING FINITE ELEMENT SIMULATIONS

The paper focuses on the combination of the Finite Element simulation and optimization to improve process or product quality. Three different examples to illustrate the developed genetic approach are given. In all three examples is-DYNA3D is used to simulate the process and a general aptimiza- tion sensitivity based strategy is utilized to improve the design. The included examples are: 1) stretch bending of tubes, 2) bulging of tubes, and finally 3) hydromechanical deep drawing. these examples clearly illustrate the potential of systematic optimization in the area of metal processing.

Hydromechanical behaviors of andesite under different stress states during fluid injection

Water reinjection into the formation is an indispensable operation in many energy engineering practices.This operation involves a complex hydromechanical(HM)coupling process and sometimes even causes unpredictable disasters,such as induced seismicity.It is acknowledged that the relative magnitude and direction of the principal stresses significantly influence the HM behaviors of rocks during injection.However,due to the limitations of current testing techniques,it is still difficult to comprehensively conduct laboratory injection tests under various stress conditions,such as in triaxial extension stress states.To this end,a numerical study of HM changes in rocks during injection under different stress states is conducted.In this model,the saturated rock is first loaded to the target stress state under drainage conditions,and then the stress state is maintained and water is injected from the top to simulate the formation injection operation.Particular attention is given to the difference in HM changes under triaxial compression and extension stresses.This includes the differences in the pore pressure propagation,mean effective stress,volumetric strain,and stress-induced permeability.The numerical results demonstrate that the differential stress will significantly affect the HM behaviors of rocks,but the degree of influence is different under the two triaxial stress states.The HM changes caused by the triaxial compression stress states are generally greater than those of extension,but the differences decrease with increasing differential stress,indicating that the increase in the differential stress will weaken the impact of the stress state on the HM response.In addition,the shear failure potential of fracture planes with various inclination angles is analyzed and summarized under different stress states.It is recommended that engineers could design suitable injection schemes according to different tectonic stress fields versus fault occurrence to reduce the risk of injection-induced seismicity.

Formulations of a hydromechanical interface element

A hydromechanical interface element is proposed for the consideration of the hydraulic-mechanical coupling effect along the interface.The fully coupled governing equations and the relevant finite element formulations are derived in detail for the interface element.All the involved matrices are of the same form as those of a solid element,which makes the incorporation of the model into a finite element program straightforward.Three examples are then numerically simulated using the interface element.Reasonable results confirm the correctness of the proposed model and motivate its application in hydromechanical contact problems in the future.

Cylindrical cavity expansion responses in anisotropic unsaturated soils under plane stress condition

In this paper,an anisotropic critical state model for saturated soils was extended to unsaturated conditions by introducing suction into its yield function.Combining this model with soil-water characteristic curves related to porosity ratio was employed to characterize the coupled hydromechanical behavior of unsaturated anisotropic soil.Based on the plane stress condition,the problem of the cylindrical cavity expansion in unsaturated anisotropic soils was transformed into first-order differential equations using the Lagrangian description.The equations were solved as an initial value problem using the Runge-Kutta algorithm,which can reflect the soil-water retention behavior during cavity expansion.Parametric analyses were conducted to investigate the influences of overconsolidation ratio(OCR),suction,and degree of saturation on the expansion responses of a cylindrical cavity in unsaturated anisotropic soil under plane stress condition.The results show that the above factors have obvious influences on the cavity responses,and the plane strain solution tends to overestimate expansion pressure and degree of saturation but underestimates suction around the cavity compared to the proposed plane stress solution.The theoretical model proposed in this paper provides a reasonable and effective method for simulating pile installation and soil pressure gauge tests near the ground surface of the unsaturated soils.

Simulation and test on separating cleaning process of flax threshing material based on gas-solid coupling theory

In order to further clarify and improve the working performance of separating cleaning device of flax threshing material,and study the motion law and characteristics of components of flax threshing material,in this paper,numerical simulation was carried out on the separating cleaning process of flax threshing material based on CFD-DEM method.Simulation results showed that the components of flax threshing material were separated and cleaned under the influence of airflow field,meanwhile,variation curves of quantity and mean velocity of flax seeds in the separating cleaning system were obtained.By referring to streamline distribution of gas-solid coupling,the quantity variation law of components of flax threshing material with time was explored and their motion curves and variation tendency of average velocity were studied.Verification test results showed that the cleaning rate of separating cleaning device for flax threshing material was 92.66%with 1.58%of total separation loss.Compared with simulation results,the test results were 1.34%and 0.93%lower,showing that it is feasible to apply the gas-solid coupling theory and method to simulate the separating and cleaning operation of flax threshing material.

Motion simulation and test on threshed grains in tapered threshing and transmission device for plot wheat breeding based on CFD-DEM

Mechanization of field experiments is the only way to improve crop breeding and seed propagation effects.In order to further clarify and improve the working performance of tapered threshing device for plot breeding,and reduce the remaining seeds in the device,the numerical simulation was carried out on the motion process of materials in the longitudinal-axial tapered cylinder threshing and transmission device of the plot wheat breeding combine harvester based on CFD-DEM method.Simulation results showed that,threshing and transmission of particles and short stalks at axial direction could be realized under the influence of air flow.Meanwhile,the material transference and distribution rule and stream field distribution rule of air flow in the threshing and transmission device were obtained,the variations of velocity and displacement of particles and short stalks with time were obtained;the motion trajectories and forms of particles in different types of retention were also studied.At rotating speed of 1300-1600 r/min for the tapered threshing cylinder in the verification test,the particle retention rate in the enclosure was 0-0.13%,while in the simulation the particle retention rate in the enclosure was 0-0.11%,only a 0.02%difference between them.The results proved a favorable feasibility to simulate the working performance of the tapered threshing and transmission device for plot breeding through gas-solid coupling method.