Increasing realism in modelling energy losses in railway vehicles and their impact to energy-efficient train control

The reduction of energy consumption is an increasingly important topic of the railway system.Energy-efficient train control(EETC)is one solution,which refers to mathematically computing when to accelerate,which cruising speed to hold,how long one should coast over a suitable space,and when to brake.Most approaches in literature and industry greatly simplify a lot of nonlinear effects,such that they ignore mostly the losses due to energy conversion in traction components and auxiliaries.To fill this research gap,a series of increasingly detailed nonlinear losses is described and modelled.We categorize an increasing detail in this representation as four levels.We study the impact of those levels of detail on the energy optimal speed trajectory.To do this,a standard approach based on dynamic programming is used,given constraints on total travel time.This evaluation of multiple test cases highlights the influence of the dynamic losses and the power consumption of auxiliary components on railway trajectories,also compared to multiple benchmarks.The results show how the losses can make up 50%of the total energy consumption for an exemplary trip.Ignoring them would though result in consistent but limited errors in the optimal trajectory.Overall,more complex trajectories can result in less energy consumption when including the complexity of nonlinear losses than when a simpler model is considered.Those effects are stronger when the trajectory includes many acceleration and braking phases.

Optimal Sizing and Power Losses Reduction of Photovoltaic Systems Using PVsyst Software

This paper presents a method for optimizing a grid-connected photovoltaic system through an LCL filter. An algorithm based on particle swarm optimization (PSO) is used to determine the number of batteries, the number of panels in series and in parallel, as well as to evaluate the joule losses due to cable heating and the switching losses of the multilevel inverters. This system is applied to a village named YAGOUA, located in the far north of Cameroon. The evaluation of the Joule effect and the switching losses as well as the regulation of the voltage level at the point of common coupling (PCC) are carried out in PVsyst and Matlab software, then at IEEE 33 bus. This algorithm reduced the Joule losses to 1.2% and the switching losses to 2.2%. A power of 210.4 MWh is produced, to be injected in the electrical network via an LCL filter. The THD calculation gave a rate of 3.015% in accordance with the 519 standards. Synchronization through the Phase Locked Loop (PLL) is performed. After the power was injected into the grid, the voltage and current remained in phase, showing the power factor correction and the efficiency of the filter. According to NASA meteorological data, the locality of YAGOUA gives the global solar irradiation forecast of 6.8 kW/m2.

Assessment of Intangible Losses in Earthquake Engineering

In order to find optimum design parameters in earthquake engineering, an objective function is optimized. This function comprises the initial cost of a structure and the cost due to the damage of earthquakes. Intangible losses may be included in the latter, such as how much society is willing to invest to preserve a human life. In this paper, the expression of the objective function is developed in terms of the seismic design coefficient, and the aforementioned intangible loss is calculated from both the individual point of view and that of society. The calculation of the intangible is based on utility curves. Finally, optimum seismic design coefficients are calculated for a firm ground site.

Simulation of charge-exchange induced NBI losses on EAST

The neutral beam injection is widely adopted in tokamaks as a key heating tool,playing a crucial role in generating burning plasmas.However,the loss of beam ions can damage the first wall and reduce the heating efficiency,resulting in failure to maintain steady-state conditions.In this work,the effect of neutral particles in the edge on fast ions generated by NBI in the Experimental Advanced Superconducting Tokamak(EAST)device is studied using the particle tracer code(PTC).The poloidal distribution of neutral particles is calculated by edge plasma simulation code SOLPS-ITER.In this simulation,four beam lines in EAST are considered:co-current tangential(co-tang),co-current perpendicular(co-perp),counter-current tangential(ctr-tang)and counter-current perpendicular(ctr-perp).It is shown that,in the absence of neutral particles,the loss fraction of ctr-injection is considerably higher than that of the co-injection.When considering the neutral particles,it is found that the ctr-perp injection demonstrates a significant variation in particles loss fraction(ranging from 18.56%to 25.42%)compared to the other three injection configurations.In terms of the loss fraction induced by neutral particles,ctr-injection exceeds co-injection,and perpendicular configuration exceeds tangential configuration.Furthermore,the difference of charge exchange ratios of three different energy(full energy,half energy,one third energy)of the four injections can be attributed to variations in the poloidal trajectories associated with each of these injections.Moreover,approximately half of fast ions which undergo neutralization directly lose to the first wall while the rest re-enter the bulk plasma and re-ionize.Except for the ctr-tang injection,the reionization ions from the other three injections exhibit effective confinement.

Repeated pregnancy losses with multiple aneuploidies and major genomic imbalance:A case report

Rationale:If one of the partners is having balanced autosomal translocation,it is usually observed that the offspring inherit either normal chromosomes,balanced translocation identical to one of the parent or unbalanced chromosomal rearrangements of the same parental chromosome having translocation.Concern:A unique case presented with history of 8 miscarriages for genetic counseling.The last abortus material evaluation showed monosomy of chromosome X(Turner syndrome)in all the analyzed cells.There was a history of infertility and also repeated second trimester abortions on the paternal side.On the maternal side,there was a history of intellectual disability.Diagnose:History of repeated abnormal pregnancy outcomes.Wife’s karyotype is normal;however,husband shows translocation between chromosome 4 and 22.Intervention:Peripheral blood sample around 3 mL was collected for karyotype.Embryo biopsy was done and DNA was extracted and processed for whole exome sequencing.Outcomes:Wife’s karyotype is normal and husband has translocation between chromosome 4 and 22.Surprisingly,the entire pregnancy outcome including embryo screening has different,complete or partial aneuploidies of chromosomes other than chromosome 4 and 22.Main lesson:Though the translocation in one of the parent is balanced,we have to think beyond traditional ways for evaluating a couple with repeated pregnancy loss as we cannot predict the errors at cell division.Option of in vitro fertilization and preimplantation genetic diagnosis in couples having balanced translocations should be discussed so that early intervention can prevent the agony of pregnancy loss.

Unraveling the efficiency losses and improving methods in quantum dot-based infrared up-conversion photodetectors

Quantum dot-based up-conversion photodetector,in which an infrared photodiode(PD)and a quantum dot light-emitting diode(QLED)are back-to-back connected,is a promising candidate for low-cost infrared imaging.However,the huge efficiency losses caused by integrating the PD and QLED together hasn’t been studied sufficiently.This work revealed at least three origins for the efficiency losses.First,the PD unit and QLED unit usually didn’t work under optimal conditions at the same time.Second,the potential barriers and traps at the interconnection between PD and QLED units induced unfavorable carrier recombination.Third,much emitted visible light was lost due to the strong visible absorption in the PD unit.Based on the understandings on the loss mechanisms,the infrared up-conversion photodetectors were optimized and achieved a breakthrough photon-to-photon conversion efficiency of 6.9%.This study provided valuable guidance on how to optimize the way of integration for up-conversion photodetectors.

Minimization of Electric Power Losses on 132 kV and 220 kV Uganda Electricity Transmission Lines

The classical minimization of power losses in transmission lines is dominated by artificial intelligence techniques, which do not guarantee global optimum amidst local minima. Revolutionary and evolutionary techniques are encumbered with sophisticated transformations, which weaken the techniques. Power loss minimization is crucial to the efficient design and operation of power transmission lines. Minimization of losses is one way to meet steady grid supply, especially at peak demand. Thus, this paper has presented a gradient technique to obtain optimal variables and values from the power loss model, which efficiently minimizes power losses by modifying the traditional power loss model that combines Ohm and Corona losses. Optimality tests showed that the unmodified model does not support the minimization of power losses on transmission lines as the Hessian matrix portrayed the maximization of power losses. However, the modified model is consistent with the gradient method of optimization, which yielded optimum variables and values from the power loss model developed in this study. The unmodified (modified) models for Bujagali-Kawanda 220 kV and Masaka West-Mbarara North 132 kV transmission lines in Uganda showed maximum power losses of 0.406 (0.391) and 0.452 (0.446) kW/km/phase respectively. These results indicate that the modified model is superior to the unmodified model in minimizing power losses in the transmission lines and should be implemented for the efficient design and operation of power transmission lines within and outside Uganda for the same transmission voltages.

Optimal Placement and Sizing of Distributed Generations for Power Losses Minimization Using PSO-Based Deep Learning Techniques

The integration of distributed generations (DGs) into distribution systems (DSs) is increasingly becoming a solution for compensating for isolated local energy systems (ILESs). Additionally, distributed generations are used for self-consumption with excess energy injected into centralized grids (CGs). However, the improper sizing of renewable energy systems (RESs) exposes the entire system to power losses. This work presents an optimization of a system consisting of distributed generations. Firstly, PSO algorithms evaluate the size of the entire system on the IEEE bus 14 test standard. Secondly, the size of the system is allocated using improved Particles Swarm Optimization (IPSO). The convergence speed of the objective function enables a conjecture to be made about the robustness of the proposed system. The power and voltage profile on the IEEE 14-bus standard displays a decrease in power losses and an appropriate response to energy demands (EDs), validating the proposed method.

Drip fertigation and plant hedgerows significantly reduce nitrogen and phosphorus losses and maintain high fruit yields in intensive orchards

A field experiment was carried out to evaluate the effects of drip fertigation combined with plant hedgerows on nitrogen and phosphorus runoff losses in intensive pear orchards in the Tai Lake Basin.Nitrogen and phosphorus runoff over a whole year were measured by using successional runoff water collection devices.The four experimental treatments were conventional fertilization(CK),drip fertigation(DF),conventional fertilization combined with plant hedgerows(C+H),and drip fertigation combined with plant hedgerows(D+H).The results from one year of continuous monitoring showed a significant positive correlation between precipitation and surface runoff discharge.Surface runoff discharge under the treatments without plant hedgerows totaled 15.86%of precipitation,while surface runoff discharge under the treatments with plant hedgerows totaled 12.82%of precipitation.Plant hedgerows reduced the number of runoff events and the amount of surface runoff.Precipitation is the main driving force for the loss of nitrogen and phosphorus in surface runoff,and fertilization is an important factor affecting the losses of nitrogen and phosphorus.In CK,approximately 7.36%of nitrogen and 2.63%of phosphorus from fertilization entered the surface water through runoff.Drip fertigation reduced the accumulation of nitrogen and phosphorus in the surface soil and lowered the runoff loss concentrations of total nitrogen(TN)and total phosphorus(TP).Drip fertigation combined with plant hedgerows significantly reduced the overall TN and TP losses by 45.38 and 36.81%,respectively,in comparison to the CK totals.Drip fertigation increased the vertical migration depth of nitrogen and phosphorus nutrients and reduced the accumulation of nitrogen and phosphorus in the surface soil,which increased the pear yield.The promotion of drip fertigation combined with plant hedgerows will greatly reduce the losses of nitrogen and phosphorus to runoff and maintain the high fruit yields in the intensive orchards of the Tai Lake Basin.

MPC-based Torque Distribution for Planar Motion of Four-wheel Independently Driven Electric Vehicles:Considering Motor Models and Iron Losses

The most critical obstacle for four-wheel independently driven electric vehicles(4WID-EVs)is the driving range.Being the actuators of 4WID-EVs,motors account for its major power consumption.In this sense,by properly distributing torques to minimize the power consumption,the driving range of 4WID-EV can be effectively improved.This paper proposes a model predictive control(MPC)-based torque distribution scheme,which minimizes the power consumption of 4WID-EVs while guaranteeing its tracking performance of planar motions.By incorporating the motor model considering iron losses,the optimal torque distribution can be achieved without an additional torque controller.Also,for this reason,the proposed control scheme is computationally efficient,since the power consumption term to be optimized,which is expressed as the product of the motor voltages and currents,is much simpler than that derived from the efficiency map.With reasonable simplification and linearization,the MPC problem is converted to a quadratic programming problem,which can be solved efficiently.The simulation results in MATLAB and CarSim co-simulation environments demonstrate that the proposed scheme effectively reduces power consumption with guaranteed tracking performance.

Robust fault detection for delta operator switched fuzzy systems with bilateral packet losses

Considering packet losses, time-varying delay, and parameter uncertainty in the switched fuzzy system, this paper designs a robust fault detection filter at any switching rate and analyzes the H∞ performance of the system. Firstly, the Takagi-Sugeno(T-S) fuzzy model is used to establish a global fuzzy model for the uncertain nonlinear time-delay switched system,and the packet loss process is modeled as a mathematical model satisfying Bernoulli distribution. Secondly, through the average dwell time method and multiple Lyapunov functions, the exponentially stable condition of the nonlinear network switched system is given. Finally, specific parameters of the robust fault detection filter can be obtained by solving linear matrix inequalities(LMIs). The effectiveness of the method is verified by simulation results.

Distributed dynamic event-based finite-time dissipative synchronization control for semi-Markov switched fuzzy cyber-physical systems against random packet losses

This paper is concerned with the finite-time dissipative synchronization control problem of semi-Markov switched cyber-physical systems in the presence of packet losses, which is constructed by the Takagi–Sugeno fuzzy model. To save the network communication burden, a distributed dynamic event-triggered mechanism is developed to restrain the information update. Besides, random packet dropouts following the Bernoulli distribution are assumed to occur in sensor to controller channels, where the triggered control input is analyzed via an equivalent method containing a new stochastic variable. By establishing the mode-dependent Lyapunov–Krasovskii functional with augmented terms, the finite-time boundness of the error system limited to strict dissipativity is studied. As a result of the help of an extended reciprocally convex matrix inequality technique, less conservative criteria in terms of linear matrix inequalities are deduced to calculate the desired control gains. Finally, two examples in regard to practical systems are provided to display the effectiveness of the proposed theory.

Financial Losses Associated with Bovine Brucellosis (Brucella abortus) in Carchi-Ecuador

Brucellosis is an infectious disease of worldwide distribution, which has a great economic impact due to the productive and reproductive losses that it causes, in addition to the serious public health problem. The aim of this study is to estimate the economic losses, through financial analysis, caused by bovine brucellosis in the province of Carchi, over a one-year period. A random sampling was used to determine the prevalence in the study area, where 2976 animals were considered, and the Rose Bengal (RB) test was used as a screening test and the Fluorescence Polarized Assay (FPA) as a confirmatory test, obtaining a prevalence of 8.2% (244/2976). In addition, parameters associated to the losses caused by brucellosis in cattle were determined by literature review. To estimate costs, field information was collected through a survey of a total of 100 randomly selected farmers. The loss estimated due to calves lost as a result of abortions and neonatal death was USD. 79170.00. The loss due to death of 4 cows as a result of metritis was estimated at USD. 5000.00. The cost of examination and treatment of aborted cows was USD. 20100.00. The losses due to reduction in milk production from aborted and non-aborted seropositive cows were estimated at USD. 158114.21. The financial losses due to brucellosis in province of Carchi were estimated at USD. 262384.21.

Characteristics of Nitrogen and Phosphorus Losses in Different Crop Rotation Systems in the North of Erhai Lake Basin

[Objective] Nitrogen and phosphorus losses of surface runoff in various crop rotation systems in the north of Erhai Lake basin were studied with the objective to provide references for risk evaluation of environmental pollution and formulating countermeasures to control the nonpoint source pollution from agriculture.[Method] Water samples collected in four typical crop rotation systems distributed in seven towns（townships） in the north of Erhai Lake basin were investigated,as well as the fertilizer input,to explore the dynamic change of nitrogen and phosphorus content in surface water of farmland and ditch water,and the correlation between fertilizer input and the concentrations of nitrogen and phosphorus in the surface water of farmland and in the ditch water.[Result] The results showed that nitrogen loss in surface water of farmland in different crop rotation systems differed greatly,and the risk of nitrogen loss was 38% lower in broad bean-rice crop rotation than that in garlic-rice crop rotation.The water soluble nitrogen was the primary form of nitrogen loss.The content of water soluble nitrogen was significantly higher in garlic-rice crop rotation than that in the other rotation systems,and the concentrations of nitrogen in the surface water of farmland in different crop rotation systems followed the sequence below：garlic-rice crop rotationryegrass-rice crop rotationbroad bean-rice crop rotationrape-rice crop rotation.The loss of phosphorus in the surface water of farmland was relatively low and phosphorus combined with silt was the primary form for phosphorus loss.There was no significant difference of the loss of various forms of phosphorus in different crop rotation systems.The contents of total nitrogen and total phosphorus in the surface water of farmland were higher than that in ditch water,with increasing rates of total nitrogen and total phosphorus in ditch water of 72% and 82%,respectively.Topdressing was the critical reason for the high concentrations of nitrogen and phosphorus in the surface water,which also caused the increasing load to the ditch water.[Conclusion] Both the nitrogen and phosphorus loss were the highest in garlic-rice crop rotation.Reasonable crop rotation systems should be established based on both the environmental and economic benefits.This study provided references for controlling the nonpoint source pollution of farmland and improving the water quality of Erhai Lake.

Post-Harvest Constraints: Fungi and Insects Responsible for Rice (Oryza spp) Losses during Storage in Cameroon

The magnitude of rice grain losses during storage is huge and warrants critical attention. We investigated the diversity of fungi and insect contamination related to losses of domestic and imported rice from local mills and markets, stored under room conditions for 10 weeks in Cameroon. The highest percentage discolored grain was on imported milled white rice (3.5%), 10 weeks after storage. In general, imported rice samples contained the highest fungal load with a proportion of 65.90% compared to 34.3% for domestic samples. Weight loss due to insect damage was up to 19.9% in white milled domestic rice. Among the 67 isolated fungi strains, the genus Aspergillus had the highest prevalence (63.8%). From all the samples, 877 insects were collected with 719 (81.9%) of Sitophilus. It is urgent to develop sustainable and affordable storage methods to limit insect and fungi infestation on rice in Cameroon.

A Discrete State Event Driven Simulation based Losses Analysis for Multi-terminal Megawatt Power Electronic Transformer

At present,power electronic transformers(PETs)have been widely used in power systems.With the increase of PET capacity to the megawatt level.the problem of increased losses need to be taken seriously.As an important indicator of power electronic device designing,losses have always been the focus of attention.At present,the losses are generally measured through experiments,but it takes a lot of time and is difficult to quantitatively analyze the internal distribution of PET losses.To solve the above problems,this article first qualitatively analyzes the losses of power electronic devices and proposes a loss calculation method based on pure simulation.This method uses the Discrete State Event Driven(DSED)modeling method to solve the problem of slow simulation speed of large-capacity power electronic devices and uses a loss calculation method that considers the operating conditions of the device to improve the calculation accuracy.For the PET prototype in this article,a losses model of the PET is established.The comparison of experimental and simulation results verifies the feasibility of the losses model.Then the losses composition of PET was analyzed to provide reference opinions for actual operation.It can help pre-analyze the losses distribution of PET,thereby providing a potential method for improving system efficiency.

Food Losses and Food Waste in the Context of Sustainable Development of the Food Sector

Globally, about one third of all food produced is wasted every year. Losses take place along the entire food chain and they need to be analyzed and monitored due to their impact on the development of the food sector. In addition to quantitative losses, irrational use of food contributes to the depletion of natural resources （water and energy） and poses a threat to the environment, constituting a barrier to sustainable development of the food sector. The aim of this study was to establish the causes and effects of food waste throughout the food supply chain and to propose mitigation measures. Identified causes of food waste can be divided into two groups. The first are those that lead to the fact that food cannot be consumed （e.g., inadequate conditions of agricultural production and interruption of the cold chain）. In the second, those that cause food cannot be sold （e.g., wrong label and wrong product weight）. Most of the identified causes of food waste can be avoided （e.g., by improving the conditions of production, storage, and transportation）. However, it is not possible to eliminate all potential errors leading to food waste. It is therefore necessary to consider what action to take to use food as intended. One way to reduce losses and food waste can be re-distributing to charity.

Calculation of AC Losses of CICC for Superconducting Outsert Coils in a Hybrid Magnet

This paper is devoted to predict AC loss of cable in conduit conductor （CICC） which is of importance in the design of conductors. The consideration for the conductor＇s design and main parameters for the magnets are introduced. In order to attain a good accuracy in the calculation of AC losses, the field distribution within superconducting outsert should be considered. Calculation of the AC losses, including hysteresis losses and coupling losses, is conducted. An emphasis is put on the hysteresis loss during the ramp up of the current to the operational current （15.3 kA） and the coupling loss of the conductor in a power-down condition for insert. The results are obtained to be 74.9 kJ and 950 J for 40 T hybrid magnets, respectively. Based on the calculation, a brief analysis of losses effect on the conductor design and the operation of magnet is given for the purpose that the capacity of the cryogenertor can be evaluated and the stability regime can be improved in our future work on the hybrid magnets.

Kalman Filtering with Partial Markovian Packet Losses

We consider the Kalman filtering problem in a networked environment where there are partial or entire packet losses described by a two state Markovian process. Based on random packet arrivals of the sensor measurements and the Kalman filter updates with partial packet, the statistical properties of estimator error covariance matrix iteration and stability of the estimator are studied. It is shown that to guarantee the stability of the Kalman filter, the communication network is required to provide for each of the sensor measurements an associated throughput, which captures all the rates of the successive sensor measurements losses. We first investigate a general discrete-time linear system with the observation partitioned into two parts and give sufficient conditions of the stable estimator. Furthermore, we extend the results to a more general case where the observation is partitioned into n parts. The results are illustrated with some simple numerical examples.

Non-technical Losses in Brazil： Subsidies for mplementation of Smart-Grid

The amount of non-technical losses in Brazil is quite elevated, accounting for nearly 5.5% of the country＇s total generated power. Such losses are asymmetrically distributed within the various regions of the country. Meter tampering （fraud）, meter bypassing by regular consumers （theft） and irregular hookups to the network by unlawful consumers are the most predominant forms of irregularities. Part of it which is caused by non-technical losses is being passed on to the consumers through the tariffs they pay. This paper presents an overview of the current situation related to non-technical losses in Brazil involving： quantification, regional asymmetry, nature and stratification, tariff management, and strategies employed to its reduction. Advanced measurement techniques provided by smart-grids can significantly reduce them. It is suggested a potential reduction of 60%. An innovative way of using these indicators in order to identify irregularities is briefly presented in this work.