Numerical investigation on flow process of liquid metals in melt delivery nozzle during gas atomization process for fine metal powder production

Based on volume of fluid(VoF)interface capturing method and shear-stress transport(SST)k-ω turbulence model,numerical simulation was performed to reveal the flow mechanism of metal melts in melt delivery nozzle(MDN)during gas atomization(GA)process.The experimental validation indicated that the numerical models could give a reasonable prediction on the melt flow process in the MDN.With the decrease of the MDN inner-diameter,the melt flow resistance increased for both molten aluminum and iron,especially achieving an order of 10^(2) kPa in the case of the MDN inner-diameter≤1 mm.Based on the conventional GA process,the positive pressure was imposed on the viscous aluminum alloy melt to overcome its flow resistance in the MDN,thus producing powders under different MDN inner-diameters.When the MDN inner-diameter was reduced from 4 to 2 mm,the yield of fine powder(<150μm)soared from 54.7%to 94.2%.The surface quality of powders has also been improved when using a smaller inner-diameter MDN.

Three-dimensional simulation of sintering crunodes of metal powders or fibers by level set method

The difference of sintering crunodes of metal powders and fibers is discussed. The mathematical model of the surface diffusion described by the difference in mean curvature is defined as a Hamilton-Jacobi-type equation, and the model is numerically solved by the level set method. The three-dimensional numerical simulations of two metal powders and fibers(the fiber angle is 0° or 90°) are implemented by this mathematical model, respectively. The numerical simulation results accord with the experimental ones. The sintering neck growth trends of metal powders and metal fibers are similar. The sintering neck radius of metal fibers is larger than that of metal powders. The difference of the neck radius is caused by the difference of geometric structure which makes an important influence on the curvature affecting the migration rate of atoms.

A NEW MECHANISM OF ULTRASOUND ATTENUATION IN SINTERED METAL POWDERS

This paper analyzes the anomalous power-law dependence of the ultrasound attenuation on frequency by means of a percolation model. It was suggested that the anomaLous ultrasound attenuation is associated with strongly localized eigen modes (to be called fracton) in disordered systems. There exits a steplike increase in the density of vibrational states at crossover frequency ω(co).Computer simulation of vibration spectrum in disordered system is also reported. The density of vibrational states is consistent with the results of relevant experiment outlined above.

Producing High Purity Nickel Metal Powder from Nickel Wastes through Acidic Leaching by Sulfuric Acid

Nickel has found increasing application in electronic,automobile manufacturing,plating,and metal industries and so on.Producing high quality metal powders to satisfy increasing demand for advanced materials is of very high importance.There are a few numbers of standard powder production techniques.An acidic leaching has been applied in present research.Sulfuric acid has been used to leach nickel wastes of plating industry.To produce nickel oxide powder furnaces with no protecting atmosphere and to produce pure nickel powder,tube furnace with hydrogen atmosphere has been applied.Variables performed in the research are time,density of sulfuric acid,and amount of hydrogen peroxide.To analyze powders produced,EDS element analysis and to determine size of powder particles,SEM has been applied.It was shown by the results that the highest amount of nickel dissolution in sulfuric acid(98%)has taken place during one hour and there is a direct relationship between hydrogen peroxide amount and nickel dissolution in sulfuric acid.

Impact mechanism of gas temperature in metal powder production via gas atomization

This paper aims at studying the influence mechanism of gas temperatures(300 K,400 K,500 K,and 600 K)on gas atomization by simulating the integral atomization process of the close-coupled nozzle in vacuum induction gas atomization(VIGA).The primary atomization is simulated by the volume of fluid(VOF)approach,and the second atomization is studied by the discrete phase model(DPM)combined with the instability breakage model.The results show that,at an increased gas temperature,the influences of gas-liquid contact angle and gas temperature in the recirculation zone on the primary atomization are virtually negligible.However,increasing the gas temperature will increase the gas-liquid relative velocity near the recirculation zone and decrease the melt film thickness,which are the main reasons for the reduced mass median diameter(MMD,d50)of primary atomized droplets.During the secondary atomization,increasing the gas temperature from 300 K to 600 K results in an increase in the droplet dispersion angle,which is beneficial to the formation of spherical metal powder.In addition,increasing the gas temperature,the positive effect of gas-liquid relative velocity increase on droplets refinement overweighs the negative influence of the GMR decrease,resulting in the reduced MMD and diameter distribution interval.From the analysis of the atomization mechanism,the increase in atomization efficiency caused by increasing the temperature of the atomizing gas,including primary atomization and secondary atomization,is mainly due to the increase in the gas drag force difference between the inner and outer sides of the annular liquid film.

INDUCTION PLASMA REACTIVE DEPOSITION OF TUNGSTEN CARBIDE FROM TUNGSTEN METAL POWDER

Experimental results on the primary carburization reaction between the tungsten powder and methane in the induction plasma, and the secondary carburization of the deposit on substrate at high temperature are reported. Optical microscopy and scanning electron microscopy were used to examine the microstructures of starting tungsten powder, carburized powder, and deposit. X-ray diffraction analysis, thermal gravimetric analysis and microhardness measurement were used to characterize the structures and properties of the powder and the deposit. It is found that the primary carburization reaction in the induction plasma starts from the surface of tungsten particles when the particles are melted. Tungsten particles are partially carburized inside the reactive plasma. Complete carburization is achieved through the secondary carburization reaction of the deposit on substrate at high temperature.

Microstructural evolution during direct laser sintering of multi-component Cu-based metal powder

A multi-component Cu-based metal powder was chosen for direct laser sintering. The powder consists of a mixture of high-purity Cu powder, pre-alloyed CuSn and CuP powder. Liquid phase sintering with complete melting of the binder (CuSn) but non-melting of the cores of structural metal (Cu) proves to be a feasible mechanism for laser sintering of this powder system. The microstructural evolution of the sintered powder with variation of laser processing parameters was presented. High sintering activities and sound densification response were obtained by optimizing the laser powers and scan speeds. Using a high laser power accompanied by a high scan speed gives rise to balling effect. At a high laser power with a slow scan speed the sintering mechanism may change into complete melting/solidification, which decreases the obtainable sintered density. The role of additive phosphorus in the laser sintering process is addressed. Phosphorus can act as a fluxing agent and has a preferential reaction with oxygen to form phosphatic slag, protecting the Cu particles from oxidation. The phosphatic slag shows a concentration along grain boundaries due to its light mass as well as the short thermal cycle of SLS.

Fabrication and Analysis of Vanadium-Based Metal Powders for Selective Laser Melting

Vanadium Alloy is a type of advanced nuclear material with many ideal properties compared as traditional nuclear materials, which has very wide and important application in first-wall and blanket structural material for fusion power plant applications. So it has attracted increasing attentions, especially on new manufacturing methods, such as selective laser melting and so on. In this paper, the comparative study of the powders obtained by mechanical mixing method, dry grinding method and wet grinding method respectively was performed to evaluate the effect of ball milling process on the microstructure and degree of alloying of the vanadium-based powder mixtures with the nominal composition of V5Cr5Ti vanadium alloy. The powders prepared by dry grinding method exhibits better spherical-like morphology and degree of alloying than those prepared by mechanical mixing method and wet grinding method, which indicates that dry grinding method can be used to prepare the superfine vanadium alloy powders for selective laser melting. This work provides a new method as well as important insights into the preparation of superfine vanadium alloy powders for selective laser melting additive manufacturing technology.

Structural Characteristics and Properties of Precious Metal Powders and Copper Powder Prepared by High-speed Centrifugal Atomization Technique

The principle and characteristics of the rapidly solidified centrifugal atomization technique are studied in present paper.It has been widely used to make fine,rapidly solidified precious metal powders for application as the electrical engineering materials,conductive coatings for electromagnetic shielding and brazing alloys.The silver powder,copper powder and some precious metal alloys powders are prepared by the new method.A comparative analysis is carried out with the conventional electrolytic silver powder and chemical deposition silver powder.The results show that rapidly solidified powders are fine and have higher solid solubility of the alloying elements,and their alloys have excellent properties in various aspects.

Nano-scaled metal powder improving tribological properties of lubricant

Cu nanoparticles were fabricated by ball milling with the anhydrous alcohol as dispersant. The size and figure of Cu nanoparticles were characterized by X-ray diffractometry and transmission electron microscopy. The tribological properties of adding Cu and MoS2 nanoparticles to the pure grease were measured on MM-200 tester, compared with the single additive and pure grease. The results show the size of Cu nanoparticles is about 50 nm. The surface with lubricant added nanopowder as additive possesses a remarkable decrease in wear volume. The friction coefficient and wear volume of lubricant mixed with 5% copper and 30% disulfide molybdenum nanoparticles are 0.09 and 1.80mm3, respectively. This mixed additive can not only increase the ability of supporting heavy load but repair the microscopic channels and cracks on the wear surface. Under higher load and long period of time, this lubricant has the characteristics of self-repairing, occluding resistance and ability of enduring higher temperature.

Sphericizing metal powders by mechanical means

A dry mechanical surface treatment was described, in which irregularly shaped metal powders were impacted and sphericized by using high speed airflow impact method particles composite system(PCS). The optimum technological parameters for the metal powders processed were determined according to the treatment effect under different conditions. The results show that the irregularly shaped metal powders are impacted into dense spherical particles, the bulk density and tap density of the metal powders increase noticeably. The combination property of metal powders is improved greatly.

Effects of Metal and Composite Metal Nanopowders on the Thermal Decomposition of Ammonium Perchlorate (AP) and the Ammonium Perchlorate/Hydroxyterminated Polybutadiene (AP/HTPB) Composite Solid Propellant

Effects of metal (Ni, Cu, Al) and composite metal (NiB, NiCu, NiCuB) nanopowders on the thermal decomposition of ammonium perchlorate (AP) and composite solid propellant ammonium perchlorate/hydroxyterminated polybutadiene (AP/HTPB) were studied by thermal analysis (DTA). The results show that metal and composite metal nanopowders all have good catalytic effects on the thermal decomposition of AP and AP/HTPB composite solid propellant. The effects of metal nanopowders on the thermal decomposition of AP are less than those of the composite metal nanopowders. The effects of metal and composite metal nanopowders on the thermal decomposition of AP are different from those on the thermal decomposition of the AP/HTPB composite solid propellant.

Aspects of the Powder in Metal Additive Manufacturing: A Review

The most widely used metal additive manufacturing processes utilize powder that is spread or fed onto a building platform. Although there are reviews of the literature on some aspects of the powder, many aspects have been under-reviewed or unreviewed. The present work is a review of the literature on these aspects. Articles published in the open literature through the end of February 2022 were collected by consulting highly regarded relevant bibliographic databases, such as Google Scholar and Science Direct. The aspects reviewed were emerging methods of powder production, methods used to improve the quality of a powder after production by a well-established method, influence of variables of well-established powder production methods on powder properties, influence of powder production method on powder properties, and influence of powder reuse on properties of powders of a wide collection of alloys. One key finding was that with regard to powder reuse, the only consistent finding is that it leads to increase in the oxygen content of the powder. Another key finding was that the literature on the aspects of the literature reviewed herein contains many shortcomings and gaps, which suggest potential areas for future research, such as techniques for optimization of process variables for a given combination of metal powder and powder production method and development of methods for production of powders of new/emerging metallic materials.

Preparation of Chromium-iron Metal Powder from Chromium Slag by Reduction Roasting and Magnetic Separation

Chromium slag（CS）has become one of the most hazardous solid waste containing chromium and iron.Based on its characteristics,the technology of reduction roasting and magnetic separation was employed to treat CS.The major impurity element of CS is magnesium and it exists in magnesium ferrite phase,which is hard to recover iron in the absence of additives.During reduction roasting,additives（Al2O3and CaF2）could destroy the structure of magnesium ferrite and improve the iron grade and recovery.The final product,i.e.chromium-iron powder,contains 72.54% Fe and 13.56% Cr,with the iron recovery of 80.34% and chromium recovery of 80.70%.

Studies on Acid Leaching Methods for Fine Metal Powder Production

Two different processes (i) alloying followed by selective leaching of alloying constituent and (ii) controlled chemical attack of oversize powder stock were studied in some detail to assess their suitability for metal powder production. In a typical series of experiments on the alloying process, titanium, zirconium and nickel were alloyed with aluminium. The sample was then leached out with acid to yield the metals in powder form. The metal powders generally had a particle size spread in the range of <5 μm. The acid concentration and contact time were varied and both have influences on particle size of the final product. In the second process involving chemical attack of coarse powder, it is shown by taking the example of nickel that a range of particle size could be generated through close control of acid concentration and contact time.

IGNITING SHS BY LASER AND ITS APPLICATION TO SELECTIVE LASER SINTERING OF METALLIC POWDER MATERIAL

How to directly fabricate metallic functional parts with selective laser sintering (SLS) process is a potential technique that scientists are researching. Existent problems during directly fabricating metal part by use of SLS are analyzed. For the sake of solving the problems, a new idea of adding self-propagating high-temperature synthesis (SHS) material into metallic powder material to form new type of SLS metallic powder material is put forward. This powder material can release controllable amount of heat during its interaction with the laser beam energy to reduce the requirement to laser power during directly sintering metallic part, to prolong the time of metallic liquid phase existing, and to improve the intensity and accuracy of SLS part. For this reason, SHS material′s interaction with the CO2 laser beam energy is researched, which proves that CO2 laser beam energy may instantly ignite SHS reaction. On the basis of the above-mentioned researches, the effect of sintering the metal powder material mixing SHS material with CO2 laser is also researched, which shows: there is an optimal blending ratio of various material in the new metallic powder material. Under the optimal blending ratio and SLS process parameters, this new metallic powder material can indeed release amount of heat and SHS reaction may be controlled within the laser sintering. This research result makes it possible that the metallic part is directly sintered with small CO2 laser (less than 50W), which may greatly reduce the volume, cost and running expenditure of SLS machine, be propitious to application.

PREPARATION OF NANOSIZED METAL-OXIDE ULTRAFINE POWDERS BY ATOMIZING-COMBUSTION TECHNIQUE

Ｔｈｅｎａｎｏｓｉｚｅｄｍｅｔａｌ－ｏｘｉｄｅｏｆＴｉｎ（Ｓｎ），Ｉｎｄｉｕｍ（Ｉｎ），Ｂｉｓｍｕｔｈ（Ｂｉ）ａｎｄｓｏｏｎａｒｅｈｉｇｈｑｕａｌｉｔｙｃｅ－ｒａｍｉｃｍａｔｅｒｉａｌｓ．Ａｓｔｈｅｌａｔｅｓｔｓｔｕｄｉｅｓｈａｖｅｓｈｏｗｎ，ｐｒｏ...

Densification Model for Porous Metallic Powder Materials

A new mechanical model for powder metallurgy compaction is presented. In this model, various amount of voids can be introduced into a continuous solid, therefore porosity can be conveniently controlled. The elastic-plastic finite element method was used to analyze the sintered powder material. The model was used to simulate compressing of a sintered cylinder. MSC.Marc of MSC. Software Corporation was applied here, and the sintered powder model was built in MSC.Mentat. The sintered cylindrical powder metallurgy part is treated as a piece of normal metal with pores in the model. The metal block is considered as cylinder with a radius of 6.0 mm and a total height of 10.0 mm. Young’s module was assumed to be 4 000 MPa. Poisson’s ratio was 0.269. The initial yield stress is 210 MPa. Friction coefficient used for the upper and lower contact surfaces is 0.3. Coulomb principle is adopted. Considering axisymmetricity, just half a section is analyzed. Totally there are 1 240 elements. Experiment was carried out by a computer controlled a universal tensile testing machine. During the experiment, the sample was prepared from highly compressible water atomized iron powder with 0.6wt% polymeric lubricant. Particle size is about 100～150 μm. The comparison was performed using a sintered cylindrical sample. The green compact was sintered at 1 140 ℃ for 2 hours. Initially, H0 is 10.20 mm, Φ0 is 12.01 mm and the initial relative density is 0.789. After pressing, H is 7.30 mm, Φ1 is 13.10 mm, Φ2 is 14.64 mm and relative density is 0.88. The load-displacement curves agree with the experimental results very well. Plastic deformation of metallic material is mostly caused by the slipping of crystal lattice. Although very small, a metal powder particle is composed of metallic crystal. Mechanical properties of a powder particle should be very close to their as solid metal counterpart.

Selective Laser Melting Process of Fe-Ni Metal Powder

The density of the SLM forming parts is investigated to determine the good technological parameters of SLM at the same time obtain the dense parts. In the SLM experiment, material used is Fe-Ni metal powder, the good technological parameters of SLM are determined by analyzing the effect of the laser electric current, the laser pulse width, the pulse of laser light frequency, the scan speed, the scan interval, push powder thickness and the scanning way on the single channel scanning, the single-layer scanning, which can lay the foundation for afterward block body formation. Microstructure and properties of the block specimen prepared under the different SLM process parameter are studied by the density measurement and the scanning electronic microscope analysis. The forming parts with high density have been prepared under the optimal SLM process parameters.

Mechanical and ballistic properties of powder metal 7039 aluminium alloy joined by friction stir welding

7039 Al alloy plates which were used as armor materials were produced by powder metallurgy method. The prepared mixed powders were pressed and plated by extrusion process. These plates, after being subjected to T6 heat treatment, were joined double-sided by friction stir welding method. Microstructure and microhardness of the welded plate were investigated. It was determined that the finest grain structure and the lowest hardness value occurred in the stir zone as 2-6 mm and HV 80.9, respectively. In order to determine the ballistic properties of welded plates, 7.62 mm armor piercing projectiles were shot to the base metal（BM）, heat affected zone（HAZ）, and thermomechanically affected zone＋stir zone（TMAZ＋SZ）. Ballistic limits（v_（50）） of these zones were determined. The ballistic limits of the BM, TMAZ＋SZ, and HAZ of the plate were approximately 14.7%, 15.3%, and 17.9% lower than that of the standard plate at the same thickness, respectively. It was determined that the armor piercing projectiles created petaling and ductile hole enlargement failure types at the armor plate. Ballistic and mechanical results can be enhanced by hot-cold rolling mills after extrusion and particle reinforcement.