高速电磁阀相移PWM电压驱动策略

高速电磁阀作为数字流量技术的核心控制元件,其动态响应及有效可控占空比区间严重影响系统流量控制精度。为进一步扩展有效可控占空比区间,提出一种包含基准脉冲宽度调制(PWM)、预激励PWM、激励PWM、高频PWM、预卸荷PWM、卸荷PWM在内的相移PWM电压驱动策略,给出相移PWM电压驱动策略的工作原理,并建立高速电磁阀动态特性理论模型,开展预激励PWM、预卸荷PWM可控占空比仿真分析与实验验证研究。结果表明:所提策略与复合PWM电压驱动策略相比,阀芯开启、关闭压力响应时间分别缩小了87%、37.9%,工作频率为100 Hz,阀芯正常启闭可控占空比为0.285~0.77,自扩展至0.085~0.81。

不平衡电网下三相PWM整流器模型预测控制及纹波抑制方法

针对三相电网不平衡故障下的电压型PWM整流器的直流电压二次纹波和网侧电流谐波,研究了一种纹波抑制方法。基于传统的双闭环控制结构,提出电网不对称故障下参考电流计算方法。利用模型预测控制取代电流环PI控制,结合PWM调制环节固定开关频率,根据电流预测模型和电流误差最小原则,不仅减小了网侧电流谐波和直流母线侧电压纹波,而且降低了平均开关次数进而减少了器件损耗。通过建立的交流侧110 V、直流侧300 V、输出功率0.7 k W的实验平台进行了实验验证,表明该系统具有良好的稳态性能。仿真结果和实验结果验证了所提出控制方法的有效性以及理论分析的正确性。

Defect Engineering with Rational Dopants Modulation for High‑Temperature Energy Harvesting in Lead‑Free Piezoceramics

High temperature piezoelectric energy harvester(HTPEH)is an important solution to replace chemical battery to achieve independent power supply of HT wireless sensors.However,simultaneously excellent performances,including high figure of merit(FOM),insulation resistivity(ρ)and depolarization temperature(Td)are indispensable but hard to achieve in lead-free piezoceramics,especially operating at 250°C has not been reported before.Herein,well-balanced performances are achieved in BiFeO3–BaTiO3 ceramics via innovative defect engineering with respect to delicate manganese doping.Due to the synergistic effect of enhancing electrostrictive coefficient by polarization configuration optimization,regulating iron ion oxidation state by high valence manganese ion and stabilizing domain orientation by defect dipole,comprehensive excellent electrical performances(Td=340°C,ρ250°C>10^(7)Ωcm and FOM_(250°C)=4905×10^(–15)m^(2)N^(−1))are realized at the solid solubility limit of manganese ions.The HT-PEHs assembled using the rationally designed piezoceramic can allow for fast charging of commercial electrolytic capacitor at 250°C with high energy conversion efficiency(η=11.43%).These characteristics demonstrate that defect engineering tailored BF-BT can satisfy high-end HT-PEHs requirements,paving a new way in developing selfpowered wireless sensors working in HT environments.

Increase in the variability of terrestrial carbon uptake in response to enhanced future ENSO modulation

El Niño-Southern Oscillation(ENSO)is a major driver of climate change in middle and low latitudes and thus strongly influences the terrestrial carbon cycle through land-air interaction.Both the ENSO modulation and carbon flux variability are projected to increase in the future,but their connection still needs further investigation.To investigate the impact of future ENSO modulation on carbon flux variability,this study used 10 CMIP6 earth system models to analyze ENSO modulation and carbon flux variability in middle and low latitudes,and their relationship,under different scenarios simulated by CMIP6 models.The results show a high consistency in the simulations,with both ENSO modulation and carbon flux variability showing an increasing trend in the future.The higher the emissions scenario,especially SSP5-8.5 compared to SSP2-4.5,the greater the increase in variability.Carbon flux variability in the middle and low latitudes under SSP2-4.5 increases by 30.9%compared to historical levels during 1951-2000,while under SSP5-8.5 it increases by 58.2%.Further analysis suggests that ENSO influences mid-and low-latitude carbon flux variability primarily through temperature.This occurrence may potentially be attributed to the increased responsiveness of gross primary productivity towards regional temperature fluctuations,combined with the intensified influence of ENSO on land surface temperatures.

Crystallization Modulation and Holistic Passivation Enables Efficient Two‑Terminal Perovskite/CuIn(Ga)Se_(2)Tandem Solar Cells

Two-terminal(2-T)perovskite(PVK)/CuIn(Ga)Se_(2)(CIGS)tandem solar cells(TSCs)have been considered as an ideal tandem cell because of their best bandgap matching regarding to Shockley–Queisser(S–Q)limits.However,the nature of the irregular rough morphology of commercial CIGS prevents people from improving tandem device performances.In this paper,D-homoserine lactone hydrochloride is proven to improve coverage of PVK materials on irregular rough CIGS surfaces and also passivate bulk defects by modulating the growth of PVK crystals.In addition,the minority carriers near the PVK/C60 interface and the incompletely passivated trap states caused interface recombination.A surface reconstruction with 2-thiopheneethylammonium iodide and N,N-dimethylformamide assisted passivates the defect sites located at the surface and grain boundaries.Meanwhile,LiF is used to create this field effect,repelling hole carriers away from the PVK and C60 interface and thus reducing recombination.As a result,a 2-T PVK/CIGS tandem yielded a power conversion efficiency of 24.6%(0.16 cm^(2)),one of the highest results for 2-T PVK/CIGS TSCs to our knowledge.This validation underscores the potential of our methodology in achieving superior performance in PVK/CIGS tandem solar cells.

Design of Serially Concatenated Two-Level Polar Coded Modulation System with Low-Complexity

Multilevel coding(MLC)is a commonly used polar coded modulation scheme,but challenging to implement in engineering due to its high complexity and long decoding delay for high-order modulations.To address these limitations,a novel two-level serially concatenated MLC scheme,in which the bitlevels with similar reliability are bundled and transmitted together,is proposed.The proposed scheme hierarchically protects the two bit-level sets:the bitlevel sets at the higher level are sufficiently reliable and do not require excessive resources for protection,whereas only the bit-level sets at the lower level are encoded by polar codes.The proposed scheme has the advantages of low power consumption,low delay and high reliability.Moreover,an optimized constellation signal labeling rule that can enhance the performance is proposed.Finally,the superiority of the proposed scheme is validated through the theoretical analysis and simulation results.Compared with the bit interleaving coding modulation(BICM)scheme,under 256-quadrature amplitude modulation(QAM),the proposed scheme attains a performance gain of 1.0 dB while reducing the decoding complexity by 54.55%.

Taming of trinitromethyl-oxadiazole to access high density and high oxygen balance via a dual modulation strategy

Energetic compounds bearing the trinitromethyl group are garnering broad attraction as potential candidates for a new generation of high energy dense oxidizers.In this work,an effective dual modulation strategy involving both molecular isomerization and crystal morphology control was employed to design and optimize trinitromethyl-oxadiazole with improved comprehensive performance.Utilizing this dual strategy,3,5-bis(trinitromethyl)-1,2,4-oxadiazole(3)was synthesized,resulting in the formation of two distinct crystal morphologies(needle and sheet)corresponding to two crystal forms(3-a and3-b).Encouragingly,while maintaining ultra-high oxygen balance(21.73%),3 achieves impressive densities(1.97-1.98 g/cm^(3)).To our knowledge,the density of 1.98 g/cm^(3)for 3-a sets a new record among that of nitrogen-rich monocyclic compounds.Notably,practical crystal morphology prediction was creatively introduced to guide the experimental crystallization conditions of 3,increasing the impact sensitivity and friction sensitivity from 1 J to 80 N(3-a)to 10 J and 240 N(3-b),respectively.Additionally,the crystal structural analyses and theoretical calculations were conducted to elucidate the reasons of differences between 3-a and 3-b in density and stability.This work provides an efficient strategy to enhance performance of trinitromethyl derivatives,broadening the path and expanding the toolbox for energetic materials.

A Multi-Task Learning Framework for Joint Sub-Nyquist Wideband Spectrum Sensing and Modulation Recognition

The utilization of millimeter-wave frequencies and cognitive radio(CR)are promising ways to increase the spectral efficiency of wireless communication systems.However,conventional CR spectrum sensing techniques entail sampling the received signal at a Nyquist rate,and they are not viable for wideband signals due to their high cost.This paper expounds on how sub-Nyquist sampling in conjunction with deep learning can be leveraged to remove this limitation.To this end,we propose a multi-task learning(MTL)framework using convolutional neural networks for the joint inference of the underlying narrowband signal number,their modulation scheme,and their location in a wideband spectrum.We demonstrate the effectiveness of the proposed framework for real-world millimeter-wave wideband signals collected by physical devices,exhibiting a 91.7% accuracy in the joint inference task when considering up to two narrowband signals over a wideband spectrum.Ultimately,the proposed data-driven approach enables on-the-fly wideband spectrum sensing,combining accuracy,and computational efficiency,which are indispensable for CR and opportunistic networking.

A Kind of PWM Pneumatic Servo Control System——Modulation Methods and Dynamic Responses

Vibrations or dither's are features of the PWM servo control system in their steady outputs. On the grounds of analyses and experiments of a PWM pneumatic servo control system, the paper puts forward four varieties of PWM modulation methods, and concludes on the relationship between dithers and the different methods, and then discusses the influence of friction to the dithers. Results from experiments regarding the dynamic and static responses on the given system support the theories presented.

考虑PWM波形特征的纳米晶磁心损耗模型的研究及验证

磁心损耗精确预测对于电力电子变压器的优化设计至关重要。然而,传统的磁心损耗模型在复杂激励下适用性较差,尤其对于占空比可调、高次谐波含量丰富的PWM波磁心损耗预测,计算精度显著下降。基于Jordan损耗分离模型,建立了一种考虑PWM波形特征的磁心损耗计算方法。首先,该方法根据激励波形特征,推导出相应的波形系数及等效频率来计算PWM波激励下的动态涡流损耗,将Jordan模型的适用范围从正弦拓展到PWM波激励下的磁心损耗计算;然后,分析了不同占空比激励下激励波形有效频率及高次谐波含量变化对损耗系数的影响,并对其进行数学表征,实现了整个占空比范围内磁心损耗的精确预测;最后,搭建了高频非正弦激励下软磁材料磁特性测量平台,针对1K107B纳米晶材料,测量了两种典型PWM波激励下的损耗数据。实验结果表明,所建立的磁心损耗模型具有较高的计算精度,相比于传统的Steinmetz改进公式,整体精度提高了25%。

一种低延时低功耗PWM比较器电路设计

设计了一种基于HHGrace 0.35μm BCD工艺的低延时低功耗电压型静态脉冲宽度调制(Pulse Width Modulation,PWM)比较器,主要应用于高频低功耗的开关电源系统。设计中包含动态尾电流源和改进型正反馈放大器,以改进传统跨导放大器(Operational Transconductance Amplifier,OTA)型比较器高延迟和高功耗等问题。仿真结果表明:在1.2~5.0 V供电电压范围内稳定工作,最大上升沿延时35 ns,最大下降沿延时41 ns,支持6 MHz开关频率的系统,比较精度8 mV,失调电压439μV,静态功耗仅为2.5μA(1.2 V供电)和4.4μA(5.0 V供电)。

不平衡电网下电流源型PWM整流器改进型无差拍控制

三相电流源型PWM整流器运行在电网电压不平衡情况下,引起直流侧及网侧电流存在大量低次谐波,势必对后级变换器供电稳定性、安全性等存在不利影响。针对该问题,首先建立整流器数学模型,推导出不平衡电网下直流侧电压和网侧电流表达式,揭示出系统直流侧和网侧电流产生低次谐波的机理。其次,根据瞬时功率理论设计内环电流参考指令,并利用无差拍控制实现网侧电流对参考电流的跟踪。然而传统无差拍控制存在延时问题,将影响网侧电流的跟随性能,造成电能质量下降。为解决该问题,提出了网侧电流内环改进型无差拍控制,利用两步预测法补偿系统延时。最后,基于Matlab/Simulink平台搭建仿真模型,验证所提控制策略的正确性与有效性。结果表明,所提方法能有效抑制直流侧和网侧电流低次谐波,实现网侧电流正弦化和直流侧电压稳定输出。

定频PWM控制混合桥双LLC谐振变换器研究

针对宽输出电压应用中传统频率控制LLC谐振变换器工作频率范围宽且存在较大循环电流的问题,提出1种定频PWM控制混合桥双LLC谐振变换器。根据原边侧结构的不同,所提变换器有3种拓扑结构形式,分别为半桥-半桥双LLC谐振变换器、半桥-全桥双LLC谐振变换器、全桥-全桥双LLC谐振变换器。其中,原边侧结构并联输入,2个变压器二次侧串联输出。相较于传统频率控制LLC变换器,3种拓扑形态始终在谐振频率点工作,缩小了开关频率范围;在PWM控制策略下,可以分别实现2倍电压增益、3倍电压增益和4倍电压增益以适应宽电压场合;电路中循环电流损耗低,软开关性能良好。Simulink仿真和实验结果验证了所提方案的可行性。

基于非线性扰动观测器的三相PWM整流器滑模控制

针对交流微电网中三相PWM整流器的运行状态易受负载扰动、滤波电容参数摄动影响的问题,本文提出一种基于非线性扰动观测器的三相PWM整流器滑模控制方法。首先,将负载扰动、滤波电容参数摄动等视为集总扰动,构建电压环非线性模型。其次,设计非线性扰动观测器,实现集总扰动的在线估计。为实现主动抗干扰控制和滑模抖振抑制,将估计的集总扰动引入到滑模面中,得到了一种含有扰动估计的新型滑模面。最后,基于滑模控制理论设计电压外环滑模控制器,并采用Lyapunov稳定性理论对其进行了稳定性证明。动态性能测试结果表明,非线性扰动观测器能够快速、准确地对集总扰动进行估计;与双环PI控制相比,所提控制的过渡过程时间减少了60%,电压跌落量减少了54%;滤波电容参数变化时,所提控制的动态性能保持良好。稳态性能测试结果表明,与传统滑模控制和双环PI控制相比,所提控制的电流总谐波畸变率分别减少了70%和44%,同时滑模抖振得到了有效地抑制。测试结果证明了所提控制方法的强抗负载扰动能力和良好的滤波电容参数鲁棒性。

基于PWM软开关技术的智能充电机的设计与实现

针对由工频变压器和整流电路组成的传统充电机存在体积大、不便运输、可靠性差等缺陷,采用无工频变压器开关电源技术,按照蓄电池充电特性曲线特点,采用恒流-恒压(CC-CV)充电法,进行系统方案及主电路设计,并使用整流—Buck降压斩波模式和PWM软开关技术控制充电机电路。实验表明,与工频型充电机相比,该方法能显著延长蓄电池使用寿命。

基于三矢量的PWM整流器改进模型预测直接功率控制方法

为解决传统模型预测直接功率控制存在的开关频率不恒定、计算量大、共模电压大问题,设计了一种三矢量模型预测直接功率控制方法。该方法通过在单个控制周期内输出三个不同电压矢量,克服了传统方法因连续多个周期输出相同电压矢量造成的开关频率不恒定问题;同时,在两相静止坐标系中,通过优化空间电压矢量图划分方法,采用两个代价函数确定电网电压矢量所在扇区,将算法的遍历次数从27次降至10次,克服了传统方法计算量大的问题;此外,通过去除两个冗余零矢量PPP与NNN,将共模电压抑制在Udc/3以内。最后搭建了5kW实验样机进行实验验证,仿真与实验结果表明,该方法可以有效降低计算量,输出谐波和共模电压抑制效果优于传统方法。

Research of the Unity Theory Between Three-level Space Vector and Carrier-based PWM Modulation Strategy

两电平空间矢量脉宽调制（space vector pulse widthmodulation,SVPWM）与正弦脉宽调制（sinusoidal pulse widthmodulation,SPWM）存有一定的本质关系,对于三电平,在常见的8段式SVPWM序列中可以证明,SVPWM与SPWM本质上也存在某种统一。实际的SVPWM调制中,由于要考虑中点电压平衡、减少谐波等其它性能问题,一般会利用开关冗余状态得到8段以上的开关调制序列。目前的文献中还未曾有对这些情况进行统一性地验证,因此三电平SVPWM与SPWM的统一理论存在一定的不足。研究发现,可通过严格地理论推导将传统意义上的调制波分解为2个子调制波,再进行SPWM调制,可以得到与SVPWM完全吻合的序列。该文在此方法基础上深入研究了8段以上（10、12、14段）的SVPWM调制序列与SPWM的统一。经过严格地理论推导,成功实现了含任意段数的SVPWM序列与SPWM的统一。仿真结果证明了该理论的正确性。

一种基于离散时域模型的单相PWM整流器控制参数多目标优化设计方法

单相PWM整流器一般采用电压外环比例积分、电流内环比例谐振的双闭环控制方法,在实现交流侧高功率因数的同时稳定直流侧输出电压,因此受到国内外学者的广泛研究。然而,在内外环控制参数设计阶段,传统设计方法一般根据经验选取控制参数,参数选取范围较大,且无法量化评估控制参数的时域控制效果,导致参数优化整定困难。为此,该文提出一种基于离散时域模型的内外环控制参数多目标优化设计方法。首先,采用传统设计方法确定电压外环比例、积分控制参数以及电流内环比例、谐振控制参数的安全设计空间;然后,基于离散时域模型将安全设计空间正映射至控制参数的时域性能空间,实现电流内环控制参数对交流侧功率因数以及电压外环控制参数对直流侧电压超调量的量化评估。在此基础上,通过进一步约束性能目标得到性能优化设计空间,考虑内外环控制参数的耦合效应,对内外环性能优化设计空间进行重新组合,再将其映射至性能空间,得到内外环控制目标帕累托最优前沿下的最优设计空间,从中选取内外环控制参数的优化设计点,在典型工况下实验测得的交流侧功率因数为0.981 26,直流输出电压超调量绝对值为1.37%,证明了所提优化设计方法的正确性。

模式切换结合模糊PWM的气动容腔压力控制方法

容腔压力是管路系统的主要控制对象,用高速开关阀代替普遍使用的比例阀进行压力调控,可大幅降低系统成本。针对单腔双阀压力跟踪系统,提出了一种模式切换结合模糊PWM的气动容腔压力控制方法。该方法的目的是减小超调,降低调节时间,提高压力跟踪性能。首先由模糊控制器根据偏差给出占空比指令,然后通过引入PWM将开关量转换为连续量调节,进而通过快速切换开关阀的工作模式实现容腔内压力的精细化调节。仿真结果表明:阶跃响应的超调量小于0.6%,峰值时间0.15 s,调节时间0.16 s,同时能够很好的跟踪上0.5 Hz的谐波信号,与当前控制策略相比,超调量和调节时间均有明显的降低。

三相PWM整流器离散空间矢量无模型预测电流控制策略

针对PWM整流器模型预测控制对系数参数准确性高度依赖的问题,提出一种基于离散空间矢量的无模型预测电流控制(MFPCC)策略。该策略通过矢量合成,在每个控制周期应用两个基本矢量,提高了预测电流的准确性;通过峰谷采样,分别测量并存储上一控制周期两个基本矢量作用下的电流梯度;并建立电流梯度方程,从而根据应用矢量的电流梯度进一步更新剩余6个未应用矢量的电流梯度,结合当前时刻的电流采样值,实现未来时刻的电流预测,得到下一时刻最优的虚拟矢量。该方法不依赖于任何系统参数,且消除了传统MFPCC策略中电流梯度更新停滞现象,降低了输出电流谐波。最后,通过实验和仿真验证了所提方法的有效性和优越性。