A CMOS Power Amplifier with 100% and 18% Modulation Depth for Mobile RFID Readers

Aiming at the specific protocol of RFID technology,a 915MHz CMOS transmitter front-end for OOK modulation is implemented in a 0.18μm CMOS process. The transmitter incorporates a class-E power amplifier （PA）, a modulator, and a control logic unit. The direct-conversion architecture minimizes the required on-and-off-chip components and provides a low-cost and efficient solution. A novel structure is proposed to provide the modulation depth of 100% and 18% ,respectively. The PA presents an output ldB power of 17.6dBm while maintaining a maximum PAE of 35.4%.

Morphotype dependence of Globigerinoides ruber(white)and Trilobatus sacculifer Mg/Ca ratios in the western tropical Pacific:implications for reconstructing the mixed-layer depth

Planktonic foraminifer Globigerinoides ruber(white)and Trilobatus sacculifer are the most frequently used mixedlayer dwelling species for reconstructing past oceanic environments.Specifically,the Mg/Ca ratios of these two foraminiferal species have been used for reconstructing tropical/subtropical changes in sea surface temperature(SST).However,these two species have different morphotypes,of which the spatial and temporal differences in Mg/Ca ratios and their influencing factors are still unclear.Our objective is to investigate the potential differences between the Mg/Ca ratios of these different morphotypes of G.ruber(white)and T.sacculifer in the western Philippine Sea(WPS)and determine their implications for the reconstruction of SST and upper-ocean structure.Mg/Ca measurements are made on two basic morphotypes of G.ruber(white)[sensu stricto(s.s.)and sensu lato(s.l.)]and T.sacculifer[with(w)and without(w/o)a sac-like final chamber]on samples of Site MD06-3047B from the WPS.Our results reveal that Mg/Ca ratios of different G.ruber morphotypes show consistent differences;and those of T.sacculifer morphotypes show staged variations since MIS 3.It is suggested to select a single morphotype for reconstructing SST changes using the Mg/Ca ratios of G.ruber and T.sacculifer in the WPS.Furthermore,the Mg/Ca ratios between G.ruber s.s.and G.ruber s.l.[Δ(Mg/Ca)_(G.ruber s.s.-s.l.)]downcore MD06-3047B covaries with indexes of summer monsoon.Combining with the core-top results,showing regional variation of differences in theΔ(Mg/Ca)_(G.ruber s.s.-s.l.)over the western tropical Pacific,we propose thatΔ(Mg/Ca)_(G.ruber s.s.-s.l.)may tend to reflect summer mixed layer depth.

Enhancement of modulation depth of an all-optical switch using an azo dye-ethyl red film

The polymethyl methacrylate （PMMA） film doped with an azo dye ethyl-red （ER） film is employed to demonstrate the properties of an all-optical switch by its photoinduced dichroism and birefringence. We show how to enhance remarkably the modulation depth of all-optical switches almost to 100% by using two linear polarization beams： one beam is inclined at 45° with respect to the probing beam and serves as a pumping beam, and the other beam is perpendicular to the probing beam and used as an erasing beam. Furthermore, a maximum-to-minimum output intensity ratio of 2000：1 is achieved in experiment, which is very useful and important for optical storages and image displays.

Near resonance vibration isolation on a levered-dual response(LEDAR)Coulomb-damped system by differential preloads/offsets in linear springs

The levered-dual response(LEDAR)Coulomb-damped system attains near resonant vibration isolation by differential preloads/offsets in linear springs.It takes the advantages of both the preloads/offsets in linear springs and the guiderail friction for realizing different levels of vibration isolation.The isolation capacities are investigated on the strategies with both the horizontal and vertical guiderails,with the horizontal rail only,and without guiderails.The compressive preloads generally result in the consumption of most of the initial excitation energy so as to overcome the potential threshold.The isolation onsets at the frequency ratio of 1∓0.095 on the left-hand side(LHS)and the right-hand side(RHS)of the lever are relative to the load plate connector.The observed near resonant isolation thus makes the LEDAR system a candidate for the isolation of the mechanical systems about resonance while opening a path for simultaneous harvesterisolation functions and passive functions at extreme frequencies.

Modulation Depth Based on Frequency-shift Characteristic of LiNbO3 Waveguide Electro-optic Intensity Modulator

The modulation depth, defined according to practical modulation results, which changes with the microwave power and its frequency, is significant for systems utilizing the frequency-shift characteristic of the LiNbO3 waveguide Electro-Optic Intensity Modulator （EOIM）. By analyzing the impedance mismatch between the microwave source and the EOIM, the effective voltage applied to the RF port of the EOIM is deprived from the microwave power and its frequency. Associating with analyses of the phase velocity mismatch between the microwave and the optical wave, the theoretical modulation depth has been obtained, which is verified by experimental results. We provide a method to choose the appropriate modulation depth to optimize the desired sideband through proper transmission bias for the system based on the frequency-shift characteristic of the EOIM.

A 5mW 1.8V Low Over-Sampling Ratio ΣΔ Modulator with 81dB Dynamic Range

This work demonstrates that the ΣΔ modulator with a low oversampling ratio is a viable option for the high-resolution digitization in a low-voltage environment.Low power dissipation is achieved by designing a low-OSR modulator based on differential cascade architecture,while large signal swing maintained to achieve a high dynamic range in the low-voltage environment.Operating from a voltage supply of 1.8V,the sixth-order cascade modulator at a sampling frequency of 4-MHz with an OSR of 24 achieves a dynamic range of 81dB for a 80-kHz test signal,while dissipating only 5mW.

Research of a fractional-turn ratio saturable pulse transformer and its application in a microsecond-range pulse modulator

As a combination device for a step-up pulse transformer and a magnetic switch,the saturable pulse transformer is widely used in pulsed-power and plasma technology.A fractional-turn ratio saturable pulse transformer is constructed and analyzed in this paper.Preliminary experimental results show that if the primary energy storage capacitors are charged to 300 V,an output voltage of about 19 kV can be obtained across the capacitor connected to the secondary windings of a fractional-tum ratio saturable pulse transformer.Theoretical and experimental results reveal that this kind of pulse transformer is not only able to integrate a step-up transformer and a magnetic switch into one device,but can also lower the saturable inductance of its secondary windings,thus leading to the relatively high step-up ratio of the pulse transformer.Meanwhile,the application of the fractional-turn ratio saturable pulse transformer in a μs range pulse modulator as a voltage step-up device and main switch is also included in this paper.The demonstrated experiments display that an output voltage with an amplitude of about 29 kV,and a 1.6 μs pulse width can be obtained across a 3500 Ω resistive load,based on a pulse modulator,if the primary energy storage capacitors are charged to 300 V.This compact fractional-turn ratio saturable pulse transformer can be applied in many other fields such as surface treatment,corona plasma generation and dielectric barrier discharge.

Tunable magneto optic modulation based on magnetically responsive nanostructured magnetic fluid

Magnetic fluid is a kind of functional composite material with nanosized structure and unique optical properties. The tunable magneto-optic modulation of magnetic fluid under external magnetic field, achieved by adjusting the polarization direction of incident light, is investigated theoretically and experimentally in this work. The corresponding modulation depth and response time are obtained. The accompanying mechanisms are clarified by using the theory of dichroism of magtietic fluid and the aggregation/disintegration processes of magnetic particles within magnetic fluid when the external magnetic field turns on/off.

Periodic Modulation of Nonlinearity in a Two-Core Photonic Crystal Fiber: A Numerical Investigation

We present a numerical investigation of the propagation and the switching of ultra-short pulses (100 fs) in a two-core nonlinear coupler of photonic crystal fibers constructed with periodically modulated the non-linearity fiber (PMNL-PFC). Our simulations are taking into account different amplitude and frequency modulations of the PMNL-PFC. A coupler for coupling whose length is Lc = 1.8 cm, the transmission characteristics, the compression factor, the crosstalk (Xtalk) and extinction ratio (Xratio) levels of the first order solitons were studied for low to high pump energies considering 2Lc. By an analysis on the reference channel (channel 2), it is observed that at low modulation frequencies an increase occurs in the switching power increasing transmission efficiency. For high modulation frequencies, the transmitted energy efficiency loses. The switching pulses are stronger for low frequency and high amplitude modulation. The Xtalk is a function of the measurement made on the secondary channel (channel 1). It was observed that this unwanted high-frequency energy increases to lessen the measure of the amplitude modulation. In summary, we have demonstrated that introduction of a non-linearity profile takes the periodically modulated PMNL-PFC to strong variations at transmission efficiency, Xtalk, Xratio a function of frequency and modulation amplitude and the input power.

Blind parameter estimation of pseudo-random binary code-linear frequency modulation signal based on Duffing oscillator at low SNR

Conventional parameter estimation methods for pseudo-random binary code-linear frequency modulation(PRBC-LFM)signals require prior knowledge,are computationally complex,and exhibit poor performance at low signal-to-noise ratios(SNRs).To overcome these problems,a blind parameter estimation method based on a Duffing oscillator array is proposed.A new relationship formula among the state of the Duffing oscillator,the pseudo-random sequence of the PRBC-LFM signal,and the frequency difference between the PRBC-LFM signal and the periodic driving force signal of the Duffing oscillator is derived,providing the theoretical basis for blind parameter estimation.Methods based on amplitude method,short-time Fourier transform method,and power spectrum entropy method are used to binarize the output of the Duffing oscillator array,and their performance is compared.The pseudo-random sequence is estimated using Duffing oscillator array synchronization,and the carrier frequency parameters are obtained by the relational expressions and characteristics of the difference frequency.Simulation results show that this blind estimation method overcomes limitations in prior knowledge and maintains good parameter estimation performance up to an SNR of-35 dB.

Effects of process parameters on the depth-to-width ratio of flux-cored wire underwater wet welding

The effects of process parameters on the depth-to-width ratio （D/W） of flux-cored wire underwater wet welding with a certain type of homemade .flux-cored wire are studied. It is found that the welding .speed, wire feeding speed and torch oscillating amplitude hare significant effects on the dopth-to-width ratio （D/W） of welds. The D/W ratio of welds increases significantly with the increase of welding speed without the oscillating of welding torch. It increased （from 0. 14 to 0. 26 ） with the increase of wire feeding speed while the torch oscillating. And it decreased linearly with the increase of torch oscillating amplitude. However, the influelwe of oscillating speed, wire extension and welding voltage on the D/W ratio of welds was not obvious.

Theoretical analyses on bed topography responses in large depth-to-width ratio river bends with constant curvatures

Bed morphology is the result of a dynamic response to a complex meandering river system. It is an important factor for the further development of river. Based on the meandering river characterized by a large depth-to-width ratio, a theoretical model is established with the coupling of Navier-Stokes （N-S）~ sediment transport, and bed deformation equations. The flow characteristics and bed response of river are obtained with the perturbation method. The research results show that, under the effect of two- dimensional flow disturbance, the bars and pools present the regular response. For a given sinuousness, the amplitude of the bed response can be used as a criterion to judge the bedform stability. The effects of the Reynolds number, disturbance wavenumber, sinuousness, and bed morphology gradient on the bed response development are described.

Study on the model of an insurer's solvency ratio in Markov-modulated Brownian markets

In this paper the insurer＇s solvency ratio model with or without jump diffusion process in the presence of financial distress cost is constructed, where an insurer＇s solvency ratio is characterized by a Markov-modulated dynamics. By Girsanov＇s theorem and the option pricing formula, the expected present value of shareholders＇ terminal payoff is provided.

Research on Large Depth Diameter Ratio Ultra-precision Aspheric Grinding System

In this paper, the factors of affecting surface roughness and profiles accuracy of the machined larege depth diamter ratio aspheric surfaces in ultra-precision grinding process are analyzed theoretically. An ultra-precision aspheric grinding system is then designed and manufactured. Aerostatic form is adopted to build the spindle of the workpiece, transverse guideway, longitudinal guideway and the spindle of the grinder in this system. The following specification is achieved, such as the turning accuracy of the spindle of the workpiece is 0.05 μm, radial rigidity of the spindle is GE 220N/μm, axial rigidity is GE 160 N/μm, radial rigidity of the guideway is GE 200N/μm, the highest rotational speed of the grinder is 80 000 rev/min and its turning accuracy is 0.1 μm, the resolution of linear displacement of the transverse and longitudinal guideway is 4.9 nm. Adjusting range of this adjusting mechanism is 2 mm in the Y direction, the adjusting accuracy of the precise adjusting mechanism is 0.1 μm. Micro displacement measuring system of this ultra-precision aspheric grinding adopts two-backfeed strategy, and angle displacement back-feed is realized by photoelectric encoder, it’s resolution is 655 360 pulse/rev. after 4 frequency multiplication, it’s angle displacement resolution is achieved 2 621 440 pulse/rev. Straight-line displacement is monitored by single frequency laser interferometer (DLSTAX LTM-20B, made in Japan). This CNC system adopts inimitable bi-arc step length flex CN interpolation algorithm, it’s CN system resolution is 5 nm.So this aspheric grinding system ensures profile accuracy of the machined part. The resolution of this interferometer is 5 nm. Finally, lots of ultra-precision grinding experiments are carried out on this grinding system. Some optical aspheric parts, with profiles accuracy of 0.3 μm, surface roughness less than 0.01 μm, are obtained.

Evaluation of EEG β2/θ -ratio and channel locations in measuring anesthesia depth

In this paper, the ratio of powers in the frequency bands of β2 and θ waves in EEG signals (termed as the β2/θ -ratio) was introduced as a potential enhancement in measuring anesthesia depth. The β2/θ -ratio was compared to the relative β-ratio which had been commercially used in the BIS monitor. Sensitivity and reliability of the β2/θ -ratio and EEG measurement locations were analyzed for their effectiveness in measuring anesthesia depth during different stages of propofol induced anesthesia (awake, induction, maintenance, and emergence). The analysis indicated that 1) the relative β -ratio and β2/θ-ratio derived from the prefrontal, frontal, and the central cortex EEG signals were of substantial sensitivity for capturing anesthesia depth changes. 2) Certain channel positions in the frontal part of the cortex, such as , had the combined benefits of substantial sensitivity and noise resistance. 3) The β2/θ-ratio captured the initial excitation, while the relative β -ratio did not. 4) In the maintenance and emergence stages, the β2/θ -ratio showed improved reliability. Implications: The ratio of powers in EEG frequency bands and derived from the frontal cortex EEG channels has combined benefits of substantial sensitivity and noise resistance in measuring anesthesia depth.

Single-photon modulation spectrum

We present a robust method of single-photon modulation by directly modulating the single photons and observe its fre- quency spectrum. Compared with conventional photon counting technique, the single-photon modulation spectrum shows that the method could not only realize high-frequency modulation but also obtain higher signal-to-noise ratio. Moreover, the theoretical calculations show good agreement with the experimental results.

Impact of depth ratio on flow structure and turbulence characteristics of compound open channel flows

Compound open channel flows appear in most natural rivers are of great importance in river management and flood control.In this study,large eddy simulations were carried out to simulate the compound open channel flows with four different depth ratios(hr=0.10,0.25,0.50,and 0.75).The main flow velocity,secondary flow,Reynolds stress,and bed shear stress were obtained from numerical simulations.The depth-averaged stream wise momentum equation was used to quantify the lateral momentum exchange between the main channel and floodplain.The instantaneous coherent structures were presented by the Q criterion method.The impact of hr on flow structure and turbulence charac-teristics was analyzed.The results showed that with the increase of hr,the high velocity area in the main channel shifted to the floodplain,and the dip phenomenon became more obvious;the Reynolds stress largely contributed to the lateral momentum exchange within the flows near the side walls of floodplain;and the vortex structures were found to significantly increase in the floodplain region.

Turbulent Modulation in Particulate Flow: A Review of Critical Variables

A review of the main mechanisms influencing turbulent modulation in the presence of spherical and non-spherical particles is presented. The review demonstrates the need for more numerical and experimental work with higher accuracy than obtained so far and the need to resolve the flow near the surface of particles with the aim to re-evaluate the quantitative effect of different parameters on turbulent modulation. The review reveals that non-spherical particles have more adverse effect on turbulence as compared to spherical ones, for the same ambient conditions.

An Over Modulation Strategy and Simulation Study for Matrix Converter

The over modulation strategy of matrix converter(MC) is put forward on the basis of conventional AC/DC/AC MC control theory. Firstly,imaginary AC/DC converter is over modulated to get the greatest fictitious DC voltage,secondly,imaginary DC/AC converter is over modulated,which effectively improve the voltage transfer ratio. Two voltage transfer ratio is emphatically analyzed with Fourier transform. At last,different modulation method is simulated with MATLAB,the simulation results verified the theoretical analysis and validity of the over modulation strategy,which provide a theoretical basis for the further research.

AN ITERATIVE RELIABILITY-BASED DECODING FOR LDPC CODED MODULATION SYSTEM

In this paper, A Belief Propagation concatenated Orderd-Statistic Decoder (BP-OSD) based on accumulated Log-Likelihood Ratio (LLR) is proposed for medium and short lengths Low Density Parity-Check (LDPC) codes coded Bit-Interleaved Coded Modulation (BICM) systems. The accumulated soft output values delivered by every BP iteration are used as reliability values of Soft-Input Soft-Output OSD (SISO-OSD) decoder and the soft output of SISO-OSD is used as a priori probabilities of the demodulator for the next iteration. Simulation results show that this improved algorithm achieves noticeable performance gain with only modest increase in computation complexity.