Multi-Band Antenna with Three Folded Monopoles for Mobile Communication Systems

This paper presents the design and the experimental characterization of a new multi-band antenna consisting of three folded monopoles dedicated to mobile communication systems. The originality of this paper is to get the PMR (Professional or Private Mobile Radio) band with the GSM (Global System for Mobile Communications), DCS (Digital Cellular System) and UMTS (Universal Mobile Telecommunications System) bands. The main lobe of the antenna radiates in the zenith direction with a linear polarization over all bands. It is interesting to design the proposed antenna in order to obtain better performances in terms of directive radiation pattern (especially in the PMR band) in comparison with the already existing antenna systems in the wireless market for similar purposes. The prototype was studied with the software CST-MWS (Micro wave studio 2012). The antenna has been designed and successfully measured.

Miniaturized multi-band antenna using deformed splot ring resonator

A 48 mm x 60 mm x 1 mm miniaturized multi band antenna based on deformed split ring re sonators was presented. The antenna was consisted of a micro strip line and a deformed split square ring. Its/S11/parameters were determined through numerical simulation and experimental measure ment within three working bands of 2.6 GHz to 3. 0 GHz, 3. 9 GHz to 4. 4 GHz and 5.2 GHz to 5. 8 GHz and the results showed that the parameters within all the bands were less than 10 dB. The gain at every frequency for the antenna was above 2.2 dB and it increased monotonously with the frequency from 5. 5 GHz to 7. 0 GHz.

Th-Shaped Tunable Multi-Band Antenna for Modern Wireless Applications

A compact,reconfigurable antenna supporting multiple wireless services with a minimum number of switches is found lacking in literature and the same became the focus and outcome of this work.It was achieved by designing a Th-Shaped frequency reconfigurable multi-band microstrip planar antenna,based on use of a single switch within the radiating structure of the antenna.Three frequency bands(i.e.,2007–2501 MHz,3660–3983MHz and 9341–1046 MHz)can be operated with the switch in the ON switch state.In the OFF state of the switch,the antenna operates within the 2577–3280MHz and 9379–1033MHz Bands.The proposed antenna shows an acceptable input impedance match with Voltage Standing Wave Ratio(VSWR)less than 1.2.The peak radiation efficiency of the antenna is 82%.A reasonable gain is obtained from 1.22 to 3.31 dB within the operating bands is achieved.The proposed antenna supports UniversalMobile Telecommunication System(UMTS)-1920 to 2170 MHz,Worldwide Interoperability and Microwave Access(WiMAX)/Wireless Broadband/(Long Term Evolution)LTE2500–2500 to 2690 MHz,Fifth Generation(5G)-2500/3500 MHz,Wireless Fidelity(Wi-Fi)/Bluetooth-2400 to 2480 MHz,and Satellite communication applications in X-Band-8000 to 12000 MHz.The overall planar dimension of the proposed antenna is 40×20mm2.The antennawas designed,along with the parametric study,using Electromagnetic(EM)simulation tool.The antenna prototype is fabricated for experimental validation with the simulated results.The proposed antenna is low profile,tunable,lightweight,cheap to fabricate and highly efficient and hence is deemed suitable for use in modern wireless communication electronic devices.

Study of multi-band property of rectangular microstrip patch antenna having different numbers of wide slots

The property of multi-band operation has been studied and investigated analytically through the design of a rectangular patch microstrip antenna having different numbers of wide slots arranged at both the radiating edges. The analyses were carried out using the method of moments simulation software. It is shown that a patch with three slots has a multi-band feature with four resonant frequencies at 1.6, 1.8, 2.65, and 4.83 GHz and adequate values of return loss and gain. It is also shown that a patch with two pairs of wide slots arranged at both the radiating edges has the dual band feature with resonant frequencies at 1.64 and 1.8 GHz and good values of return loss and gain.

Design of multi-band metasurface antenna array with low RCS performance

In this paper, a multi-band metasurface（MS） antenna array with low radar cross section（RCS） performance is proposed and measured. Firstly, a 44 antenna array is composed of four 22 Jerusalem cross structure antenna arrays working at different frequency bands, which is aimed at enhancing the bandwidth effectively. Then, each antenna can be seen as a unit of MS in spite of adding the feeding structure. Based on phase cancellation principle, the MS is arranged into a chessboard configuration in order to realize wideband RCS reduction. Thus, excellent radiation and scattering characteristics are obtained simultaneously. Simulated and measured results indicate that this work provides a novel method to achieve bandwidth expansion as well as wideband RCS reduction of the antenna array.

Multi-Band Rectangular Patch End-Fire Antenna Array

A novel multi-band end-fire antenna array was designed, fabricated, and characterized. Analytical calculations were carried out to determine the critical antenna dimensions and the design was optimized using a 3D electromagnetic finite-element solver. The measured results were in good agreement with the designed results. The proposed antenna array exhibits multi-band capabilities which can be potentially used for applications that require a multi-band end-fire radiation pattern.

Design of Multi-band Small Antenna Based on Single Split-Ring Resonator

To use the single split-ring resonator （SRR） as a basic unit cell for small antenna with multi-band frequency response is proposed. The structure of antenna is consisted of a single spilt-ring resonator and a coupled microstrip line. The designed antenna is numerically optimized with CST Microwave Studio. The radiation properties of the antenna show that there are three frequency bands among which two bands are 1.3 GHz and 2.1 GHz ultra-widehand （UWB）, respectively, where Sll is less than - 10 dB. The gain at every frequency for the multi-hand antenna is above 2.6 dBi, and it increases monotonously with the frequency in the two UWB.

Multi-Band Metamaterial Antenna for Terahertz Applications

A multi-band metamaterial antenna is proposed to operate at the terahertz(THz)band for medical applications.The proposed structure is designed on a polyimide as a support layer,and its radiating elements are made of graphene.Initially,the design is started with a conventional shape showing a single operating frequency at 1.1 THz.To achieve a multi-band operating frequency,the conventional shape was replaced with the proposed metamaterial as a radiating patch that has properties not exist in nature.The multi-band frequencies are obtained without compromising the overall size of the design.The overall size is 600×600×25μm^(3).The operating frequencies are 0.36,0.49,0.69,0.87,and 1.04 THz.A full ground plane is used to behave as isolation between the design and the human body model.The proposed design is investigated on free space and on the human body model,showing excellent performance in both cases.The achieved gains for the following frequencies 0.36,0.49,0.69,0.87,and 1.04 THz are 4.81,6.5,8.41,6.02,and 7.96 dB,respectively,while the efficiencies are 83.91%,96.28%,90.80%,91.71%,and 92.99%,respectively.The conventional design was modified to have a partial ground to show the benefit of using the full ground.The design is loaded on the human body model and its performance is affected.The efficiency and gain are 6.61 dB and 95.58.7%for the case of no human body model,and 4.26 dB and 40.30%for the case of using a human body model.Hence,the proposed metamaterial antenna will be useful for future medical applications in the THz band.

Dielectric Loading on Multi-Band Behaviors of Pentagonal Fractal Patch Antennas

This paper describes the multiband behaviour as well as the response for dielectric loading of a pentagonal fractal patch antenna designed at frequency f = 2.45 GHz. The proposed antenna shape has been obtained by introducing slots in a pentagonal patch antenna up to second iteration. Detailed design steps and results of the designs are studied and investigated in this paper. Simulated and measured results reveal that the antenna will be operated at three different frequency bands—2.17 GHz, 3.56 GHz, and 7.93 GHz with acceptable performances (i.e. VSWR < 2). The measured results for the antennas are in good agreement with simulated results. The proposed antenna maintains good radiation pattern with gain. However dielectric loading increases its radiation efficiency at the cost of significant decrease in gain and directivity.

The Tianma 65 m radio telescope antenna

The Tianma 65 m radio telescope(TMRT)at Shanghai is a fully steerable single-dish radio telescope in China,operating at centimeter to millimeter wavelengths(1.25 GHz to 50 GHz).This paper presents details on the main specifications,design,performance analysis,testing,and construction of the telescope antenna.The measured total efficiency is better than 50%over the whole elevation angle range,first sidelobe levels are less than−20 dB,antenna system noise temperatures are less than 70 K at 30°elevation angle,and pointing accuracy is less than 3″.The measured and calculated results are in good agreement,verifying the effectiveness of the design and analysis.

A Compact UHF Antenna Based on Hilbert Fractal Elements and a Serpentine Arrangement for Detecting Partial Discharg

Efforts to protect electric power systems from faults have commonly relied on the use of ultra-high frequency(UHF)antennas for detecting partial discharge(PD)as a common precursor to faults.However,the effectiveness of existing UHF antennas suffers from a number of challenges such as limited bandwidth,relatively large physical size,and low detection sensitivity.The present study addresses these issues by proposing a compact microstrip patch antenna with fixed dimensions of 100 mm×100 mm×1.6 mm.The results of computations yield an optimized antenna design consisting of 2nd-order Hilbert fractal units positioned within a four-layer serpentine arrangement with a fractal unit connection distance of 3.0 mm.Specifically,the optimized antenna design achieves a detection bandwidth for which the voltage standing wave ratio is less than 2 that is approximately 97.3%of the UHF frequency range(0.3–3 GHz).Finally,a prototype antenna is fabricated using standard printed circuit board technology,and the results of experiments demonstrate that the proposed antenna is capable of detecting PD signals at a distance of 8 m from the discharge source.

Assessment of the performance of the TOPGNSS and ANN-MB antennas for ionospheric measurements using low-cost u-blox GNSS receivers

Low-cost GNSS receivers have recently been gaining reliability as good candidates for ionospheric studies. In line with these gains are genuine concerns about improving the performance of these receivers. In this work, we present a comprehensive investigation of the performances of two antennas(the u-blox ANN-MB and the TOPGNSS TOP-106) used on a low-cost GNSS receiver known as the u-blox ZED-F9P. The two antennas were installed on two identical and co-located u-blox receivers. Data used from both receivers cover the period from January to June 2022. Results from the study indicate that the signal strengths are dominantly greater for the receiver with the TOPGNSS antenna than for the receiver with the ANN-MB antenna, implying that the TOPGNSS antenna is better than the ANN-MB antenna in terms of providing greater signal strengths. Summarily, the TOPGNSS antenna also performed better in minimizing the occurrence of cycle slips on phase TEC measurements. There are no conspicuous differences between the variances(computed as 5-min standard deviations) of phase TEC measurements for the two antennas, except for a period around May-June when the TOPGNSS gave a better performance in terms of minimizing the variances in phase TEC. Remarkably, the ANN-MB antenna gave a better performance than the TOPGNSS antenna in terms of minimizing the variances in pseudorange TEC for some satellite observations. For precise horizontal(North and East) positioning, the receiver with the TOPGNSS antenna gave better results, while the receiver with the ANN-MB antenna gave better vertical(Up) positioning. The errors for the receivers of both antennas are typically within about 5 m(the monthly mean was usually smaller than 1 m) in the horizontal direction and within about 10 m(the monthly mean was usually smaller than 4 m) in the vertical direction.

Physical design and recent experimental results of the new ICRF antenna on EAST

Two new ICRF antennas operating in the ion cyclotron radio frequency(ICRF) range have been developed for EAST to overcome the low coupling problem of the original antennas.The original ICRF antennas were limited in their power capacity due to insufficient coupling.The new antenna design takes into account both wave coupling and absorption processes through comprehensive wave coupling and absorption codes,with the dominant parallel wave number k∥of 7.5 m-1at dipole phasing.Through the use of these new ICRF antennas,we are able to achieve 3.8 MW output power and 360 s operation,respectively.The initial experimental results demonstrate the reliability of the antenna design method.

Prediction of Bandwidth of Metamaterial Antenna Using Pearson Kernel-Based Techniques

The use of metamaterial enhances the performance of a specific class of antennas known as metamaterial antennas.The radiation cost and quality factor of the antenna are influenced by the size of the antenna.Metamaterial antennas allow for the circumvention of the bandwidth restriction for small antennas.Antenna parameters have recently been predicted using machine learning algorithms in existing literature.Machine learning can take the place of the manual process of experimenting to find the ideal simulated antenna parameters.The accuracy of the prediction will be primarily dependent on the model that is used.In this paper,a novel method for forecasting the bandwidth of the metamaterial antenna is proposed,based on using the Pearson Kernel as a standard kernel.Along with these new approaches,this paper suggests a unique hypersphere-based normalization to normalize the values of the dataset attributes and a dimensionality reduction method based on the Pearson kernel to reduce the dimension.A novel algorithm for optimizing the parameters of Convolutional Neural Network(CNN)based on improved Bat Algorithm-based Optimization with Pearson Mutation(BAO-PM)is also presented in this work.The prediction results of the proposed work are better when compared to the existing models in the literature.

Dual-band multi-beam reconfigurable terahertz antenna based on graphene frequency selective surface

In this paper,a dual-band graphene-based frequency selective surface(GFSS)is investigated and the operating mechanism of this GFSS is analyzed.By adjusting the bias voltage to control the graphene chemical po-tential between 0 eV and 0.5 eV,the GFSS can achieve four working states:dual-band passband,high-pass lowimpedance,low-pass high-impedance,and band-stop.Based on this GFSS,a hexagonal radome on a broadband omnidirectional monopole antenna is proposed,which can achieve independent 360°six-beam omnidirectional scanning at 1.08 THz and 1.58 THz dual bands.In addition,while increasing the directionality,the peak gains of the dual bands reach 7.44 dBi and 6.67 dBi,respectively.This work provides a simple method for realizing multi-band terahertz multi-beam reconfigurable antennas.

Design of a Metasurface Antenna Based on Characteristic Mode Theory

A novel metasurface antenna consisting of 5×5 rectangular patch elements is presented.Thestructure with and without the central element are both analyzed by the Characteristic Mode Theory(CMT).The developed mutually orthogonal principal modes of the optimized periodic patch structure areexcited by a center-feed dipole.A differential feeding network is employed to realize impedance matching.Prototype with profile height of 0.07λ_(0)(λ_(0)is the wavelength in free space at the lowest operatingfrequency)is fabricated and assembled to verify the simulation results.The measured results show that thereflectance coefficient of proposed matesurface antenna is less than-10 dB in the whole operating bandrange from 4.2 GHz to 5.5 GHz,a relative bandwidth of 26.8%is achieved,and the maximummeasured realized gain is more than 9 dBi with a maximum radiation efficiency of 90%.The designprovides a guideline on the application of characteristic modes(CMs)to radiation problems.

Microstrip Patch Antenna with an Inverted T-Type Notch in the Partial Ground for Breast Cancer Detections

This study designs a microstrip patch antenna with an inverted T-type notch in the partial ground to detect tumorcells inside the human breast.The size of the current antenna is small enough(18mm×21mm×1.6mm)todistribute around the breast phantom.The operating frequency has been observed from6–14GHzwith a minimumreturn loss of−61.18 dB and themaximumgain of current proposed antenna is 5.8 dBiwhich is flexiblewith respectto the size of antenna.After the distribution of eight antennas around the breast phantom,the return loss curveswere observed in the presence and absence of tumor cells inside the breast phantom,and these observations showa sharp difference between the presence and absence of tumor cells.The simulated results show that this proposedantenna is suitable for early detection of cancerous cells inside the breast.

Deployment Dynamic Modeling and Driving Schemes for a Ring-Truss Deployable Antenna

Mesh reflector antennas are widely used in space tasks owing to their light weight,high surface accuracy,and large folding ratio.They are stowed during launch and then fully deployed in orbit to form a mesh reflector that transmits signals.Smooth deployment is essential for duty services;therefore,accurate and efficient dynamic modeling and analysis of the deployment process are essential.One major challenge is depicting time-varying resistance of the cable network and capturing the cable-truss coupling behavior during the deployment process.This paper proposes a general dynamic analysis methodology for cable-truss coupling.Considering the topological diversity and geometric nonlinearity,the cable network's equilibrium equation is derived,and an explicit expression of the time-varying tension of the boundary cables,which provides the main resistance in truss deployment,is obtained.The deployment dynamic model is established,which considers the coupling effect between the soft cables and deployable truss.The effects of the antenna's driving modes and parameters on the dynamic deployment performance were investigated.A scaled prototype was manufactured,and the deployment experiment was conducted to verify the accuracy of the proposed modeling method.The proposed methodology is suitable for general cable antennas with arbitrary topologies and parameters,providing theoretical guidance for the dynamic performance evaluation of antenna driving schemes.