ForceCT双能量与低kV扫描技术在头颈CTA中的对比分析

探索并比较Force CT双能量与低kV扫描技术在头颈CTA中的作用。方法 以系统随机化法,将2022.01-2023.01在我院接受头颈CTA检查的40例患者均分为两组各20例。其中观察组患者采用低kV扫描技术,对照组则进行Force CT双能量扫描。比较两组的辐射剂量、图像质量。结果 观察组的辐射剂量指数低于对照组,P<0.05。观察组的大脑中动脉与颈内动脉图像质量均高于对照组,P<0.05。结论 运用低kV扫描技术,能较好地降低头颈CTA检查时的辐射剂量,与此同时还能得到更为高质量的图像,帮助病情的更快诊断,患者能尽快得到个性化的治疗,早日恢复健康。

Force CT高级建模迭代重建算法对门静脉图像质量的影响

目的:探讨Force CT高级建模迭代重建算法(ADMIRE)对门静脉图像质量影响。方法:回顾性分析2022年1—4月于中山大学附属第八医院行上腹部CT平扫及增强的40例患者影像资料,在syngo.via后处理工作站重建,采用门脉期原始数据重建出滤波反投影算法(FBP)、ADMIRE1、ADMIRE3、ADMIRE5 4组不同重建算法的图像,在4组不同算法图像上测量门静脉干中心位置、肝实质及同层竖脊肌的CT值和噪声值,计算门静脉和肝实质的信噪比(SNR)和对比噪声比(CNR)。此外,由两位具有5年以上诊断经验的医生对图像进行主观评分。结果:随着迭代等级的增高,图像的CNR、SNR呈现上升的趋势,图像的噪声值呈现下降的趋势,其中ADMIRE5组图像中门静脉和肝脏具有最高的CNR和SNR且具有最低的噪声值,以及最高的主观评分,采用ADMIRE5重建算法的门静脉与周围组织对比非常好,门静脉5级分支显示良好。结论:高级建模迭代重建ADMIRE算法相比于FBP重建算法,降噪效果更好,门静脉的显示更加锐利,能提升门静脉的图像质量。

Optimization-based mode selection scheme for OAM millimeter wave system in the off-axis misalignment case

Millimeter-wave transmission combined with Orbital Angular Momentum(OAM)has the advantage of reducing the loss of beam power and increasing the system capacity.However,to fulfill this advantage,the antennas at the transmitter and receiver must be parallel and coaxial;otherwise,the accuracy of mode detection at the receiver can be seriously influenced.In this paper,we design an OAM millimeter-wave communication system for overcoming the above limitation.Specifically,the first contribution is that the power distribution between different OAM modes and the capacity of the system with different mode sets are analytically derived for performance analysis.The second contribution lies in that a novel mode selection scheme is proposed to reduce the total interference between different modes.Numerical results show that system performance is less affected by the offset when the mode set with smaller modes or larger intervals is selected.

Comparisons of Wave Force Model Effects on the Structural Responses and Fatigue Loads of a Semi-Submersible Floating Wind Turbine

The selection of wave force models will significantly impact the structural responses of floating wind turbines.In this study,comparisons of wave force model effects on the structural responses and fatigue loads of a semi-submersible floating wind turbine(SFWT)were conducted.Simulations were performed by employing the Morison equation(ME)with linear or second-order wave kinematics and potential flow theory(PFT)with first-or second-order wave forces.A comparison of regular waves,irregular waves,and coupled wind/waves analyses with the experimental data showed that many of the simulation results and experimental data are relatively consistent.However,notable discrepancies are found in the response amplitude operators for platform heave,tower base bending moment,and tension in mooring lines.PFT models give more satisfactory results of heave but more significant discrepan-cies in tower base bending moment than the ME models.In irregular wave analyses,low-frequency resonances were captured by PFT models with second-order difference-frequency terms,and high-frequency resonances were captured by the ME models or PFT models with second-order sum-frequency terms.These force models capture the response frequencies but do not reasonably predict the response amplitudes.The coupled wind/waves analyses showed more satisfactory results than the wave-only analyses.However,an important detail to note is that this satisfactory result is based on the overprediction of wind-induced responses.

Force and impulse multi-sensor based on flexible gate dielectric field effect transistor

Nowadays,force sensors play an important role in industrial production,electronic information,medical health,and many other fields.Two-dimensional material-based filed effect transistor(2D-FET)sensors are competitive with nano-level size,lower power consumption,and accurate response.However,few of them has the capability of impulse detection which is a path function,expressing the cumulative effect of the force on the particle over a period of time.Herein we fabricated the flexible polymethyl methacrylate(PMMA)gate dielectric MoS_(2)-FET for force and impulse sensor application.We systematically investigated the responses of the sensor to constant force and varying forces,and achieved the conversion factors of the drain current signals(I_(ds))to the detected impulse(I).The applied force was detected and recorded by I_(ds)with a low power consumption of~30 nW.The sensitivity of the device can reach~8000%and the 4×1 sensor array is able to detect and locate the normal force applied on it.Moreover,there was almost no performance loss for the device as left in the air for two months.

Study of the Lift Force Induced by An Interceptor on A High-Speed Mono-Hull:The Affecting Factors and Estimation Formula

To find a better way to estimate the lift force induced by an interceptor on a high-speed mono-hull ship,a series of high-speed mono-hull ship models are designed and investigated under different conditions.Different lift forces are obtained by numerical calculations and validated by a model test in a towing tank.The factors that influence the force are the interceptor height,velocity,draft,and deadrise angle.The relationship between each factor and the induced lift force is investigated and obtained.We found that the induced lift mainly depends on the interceptor height and advancing velocity,and is proportional to the square of the interceptor height and velocity.The results also showed that the effects of the draft and deadrise angle are relatively less important,and the relationship between the induced lift and these two factors is generally linear.Based on the results,a formula including the combined effect of all factors used to estimate the lift force induced by the interceptor is developed based on systematic analysis.The proposed formula could be used to estimate the lift force induced by interceptors,especially under high-speed condition.

Collision off-axis position dependence of relativistic nonlinear Thomson inverse scattering of an excited electron in a tightly focused circular polarized laser pulse

This paper presents a novel view of the impact of electron collision off-axis positions on the dynamic properties and relativistic nonlinear Thomson inverse scattering of excited electrons within tightly focused, circularly polarized laser pulses of varying intensities. We examine the effects of the transverse ponderomotive force, specifically how the deviation angle and speed of electron motion are affected by the initial off-axis position of the electron and the peak amplitude of the laser pulse. When the laser pulse intensity is low, an increase in the electron's initial off-axis distance results in reduced spatial radiation power, improved collimation, super-continuum phenomena generation, red-shifting of the spectrum's harmonic peak, and significant symmetry in the radiation radial direction. However, in contradiction to conventional understandings,when the laser pulse intensity is relatively high, the properties of the relativistic nonlinear Thomson inverse scattering of the electron deviate from the central axis, changing direction in opposition to the aforementioned effects. After reaching a peak, these properties then shift again, aligning with the previous direction. The complex interplay of these effects suggests a greater nuance and intricacy in the relationship between laser pulse intensity, electron position, and scattering properties than previously thought.

Culturally competent care across borders: Implementing culturally responsive teaching for nurses in diverse workforces

The migration of healthcare professionals,including nurses,is a global phenomenon.It is driven by various factors,including the pursuit of better opportunities,living conditions,and professional development,as well as political instability or conflict in their home countries.The World Health Organization(WHO)has noted that high-income countries often rely on foreign-trained nurses to fill gaps in their healthcare systems[1].For instance,as of 2021,over 40%(52 million)of all nurses in the United States(US)were expatriates[2].In the United Kingdom(UK),the percentage of expatriate nurses was even higher,reaching approximately 18%in 2021[3].Owing to globalization and migration,healthcare providers must possess cultural competence to deliver improved care[4,5].Culturally responsive teaching(CRT)is rooted in the idea that culture plays a vital role in shaping people’s behaviors,beliefs,values,and communication styles[6].Furthermore,these cultural factors influence patients’perspectives on health,illness,healing,and their preferences for care and communication[7].By recognizing and embracing these cultural differences,nurses can provide more effective and compassionate care to their diverse patient population[8].

Imaging a force field via an optically levitated nanoparticle array

Levitated optomechanical systems represent an excellent candidate platform for force and acceleration sensing.We propose a force-sensing protocol utilizing an optically levitated nanoparticle array.In our scheme,N nanoparticles are trapped in an optical cavity using holographic optical tweezers.An external laser drives the cavity,exciting N cavity modes interacting simultaneously with the N nanoparticles.The optomechanical interaction encodes the information of the force acting on each nanoparticle onto the intracavity photons,which can be detected directly at the output ports of the cavity.Consequently,our protocol enables real-time imaging of a force field.

Self-assembly of perovskite nanocrystals:From driving forces to applications

Self-assembly of metal halide perovskite nanocrystals(NCs)into superlattices can exhibit unique collective properties,which have significant application values in the display,detector,and solar cell field.This review discusses the driving forces behind the self-assembly process of perovskite NCs,and the commonly used self-assembly methods and different self-assembly structures are detailed.Subsequently,we summarize the collective optoelectronic properties and application areas of perovskite superlattice structures.Finally,we conclude with an outlook on the potential issues and future challenges in developing perovskite NCs.

Experimental and numerical simulation study on forced ventilation and dust removal of coal mine heading surface

In order to study the problems of unreasonable airflow distribution and serious dust pollution in a heading surface,an experimental platform for forced ventilation and dust removal was built based on the similar principles.Through the similar experiment and numerical simulation,the distribution of airflow field in the roadway and the spatial and temporal evolution of dust pollution under the conditions of forced ventilation were determined.The airflow field in the roadway can be divided into three zones:jet zone,vortex zone and reflux zone.The dust concentration gradually decreases from the head to the rear of the roadway.Under the forced ventilation conditions,there is a unilateral accumulation of dust,with higher dust concentrations away from the ducts.The position of the equipment has an interception effect on the dust.The maximum error between the test value and the simulation result is 12.9%,which verifies the accuracy of the experimental results.The research results can provide theoretical guidance for the application of dust removal technology in coal mine.

Electric field and force characteristic of dust aerosol particles on the surface of high-voltage transmission line

High-voltage transmission lines play a crucial role in facilitating the utilization of renewable energy in regions prone to desertification. The accumulation of atmospheric particles on the surface of these lines can significantly impact corona discharge and wind-induced conductor displacement. Accurately quantifying the force exerted by particles adhering to conductor surfaces is essential for evaluating fouling conditions and making informed decisions. Therefore, this study investigates the changes in electric field intensity along branched conductors caused by various fouling layers and their resulting influence on the adhesion of dust particles. The findings indicate that as individual particle size increases, the field strength at the top of the particle gradually decreases and eventually stabilizes at approximately 49.22 k V/cm, which corresponds to a field strength approximately 1.96 times higher than that of an unpolluted transmission line. Furthermore,when particle spacing exceeds 15 times the particle size, the field strength around the transmission line gradually decreases and approaches the level observed on non-adhering surface. The electric field remains relatively stable. In a triangular arrangement of three particles, the maximum field strength at the tip of the fouling layer is approximately 1.44 times higher than that of double particles and 1.5 times higher compared to single particles. These results suggest that particles adhering to the transmission line have a greater affinity for adsorbing charged particles. Additionally, relevant numerical calculations demonstrate that in dry environments, the primary adhesion forces between particles and transmission lines follow an order of electrostatic force and van der Waals force. Specifically, at the minimum field strength, these forces are approximately74.73 times and 19.43 times stronger than the gravitational force acting on the particles.

Distributed Dynamic Load in Structural Dynamics by the Impulse-Based Force Estimation Algorithm

This paper proposes a novel approach for identifying distributed dynamic loads in the time domain.Using polynomial andmodal analysis,the load is transformed intomodal space for coefficient identification.This allows the distributed dynamic load with a two-dimensional form in terms of time and space to be simultaneously identified in the form of modal force,thereby achieving dimensionality reduction.The Impulse-based Force Estimation Algorithm is proposed to identify dynamic loads in the time domain.Firstly,the algorithm establishes a recursion scheme based on convolution integral,enabling it to identify loads with a long history and rapidly changing forms over time.Secondly,the algorithm introduces moving mean and polynomial fitting to detrend,enhancing its applicability in load estimation.The aforementioned methodology successfully accomplishes the reconstruction of distributed,instead of centralized,dynamic loads on the continuum in the time domain by utilizing acceleration response.To validate the effectiveness of the method,computational and experimental verification were conducted.

Post-Traumatic Stress Disorder among Defence and Security Forces in Northern Benin (2023)

Introduction: Post-traumatic stress disorder (PTSD) is defined as “actual exposure to death or the threat of death, serious injury or sexual violence”, either directly or indirectly, resulting in a symptomatic procession of repetition, avoidance, neurovegetative hyperactivity and individualized symptoms, with or without negative cognitive and mood changes. It therefore goes without saying that the defence and security forces constitute a high-risk population in need of attention. Objective: To study post-traumatic stress disorder in defence and security forces in the city of Parakou in 2023. Methods: Descriptive cross-sectional study conducted from December 2022 to July 2023. The study population consisted of active military, republican police and firefighters in the city of Parakou in 2023. Non-proportional stratified sampling was used, given the inaccessibility of the source population size for national security reasons. Post-traumatic stress disorder was assessed using the “post-traumatic stress disorder checklist-5 (PCLS-5) scale. Results: A total of 305 subjects participated in the survey. Males dominated 90.2%. The most represented corps was the Republican Police (41.6%), most of whom were non-commissioned officers (46.6%). The majority count between 11 and 20 years of service (48.9%), with 2 to 5 missions completed (67.5%). The calculated prevalence of post-traumatic stress disorder was 11.8%, based on the post-traumatic stress disorder checklist-5 (PCL-5). Of the 36 respondents with post-traumatic stress disorder, 20 (55.6%) had experienced an armed attack, 25 (69.4%) had witnessed a violent death, 18 (50.0%) had witnessed the agony of a colleague, 15 (41.7%) had been exposed to a fire or explosion, while 26 (72.2%) had been traumatized by physical and/or verbal aggression. 5 (13.9%) had consulted a specialist psychiatrist, while 6 (16.7%) were on medication and 26 (72.2%) used sport as a means of maintaining physical and mental health. Respectively 22 (61.1%) and 21 (58.3%) had definite symptoms of anxiety and depression. Multivariate analysis revealed a significant association between post-traumatic stress disorder and the following variables: total number of children ≤ 2 (p = 0.015), comorbidities such as arterial hypertension (p = 0.007), history of hepatitis (p = 0.017), work accidents (p = 0.016), alcohol dependence (p = 0.004), domestic violence (p = 0.004), psychological violence (p = 0.017) and anxiety disorders (p Conclusion: Defence and security personnel can also be prey to post-traumatic stress disorder (PTSD), which needs to be systematically taken into account when they are subjected to trauma in the course of their duties. Mental health should be an integral part of the periodic medical check-up objectives for defence and security forces throughout the country.

An extended social force model on unidirectional flow considering psychological and behavioral impacts of hazard source

An accurate assessment of the evacuation efficiency in case of disasters is of vital importance to the safety design of buildings and street blocks.Hazard sources not only physically but psychologically affect the pedestrians,which may further alter their behavioral patterns.This effect is especially significant in narrow spaces,such as corridors and alleys.This study aims to integrate a non-spreading hazard source into the social force model following the results from a previous experiment and simulation,and to simulate unidirectional pedestrian flows over various crowd densities and clarity–intensity properties of the hazard source.The integration include a virtual repulsion force from the hazard source and a decay on the social force term.The simulations reveal(i)that the hazard source creates virtual bottlenecks that suppress the flow,(ii)that the inter-pedestrian push forms a stabilisation phase on the flow-density curve within medium-to-high densities,and(iii)that the pedestrians are prone to a less orderly and stable pattern of movement in low clarity–intensity scenarios,possibly with lateral collisions passing the hazard source.

Train wheel-rail force collaborative calibration based on GNN-LSTM

Accurate wheel-rail force data serves as the cornerstone for analyzing the wheel-rail relationship.However,achieving continuous and precise measurement of this force remains a significant challenge in the field.This article introduces a calibration algorithm for the wheel-rail force that leverages graph neural networks and long short-term memory networks.Initially,a comprehensive wheel-rail force detection system for trains was constructed,encompassing two key components:an instrumented wheelset and a ground wheel-rail force measuring system.Subsequently,utilizing this system,two distinct datasets were acquired from the track inspection vehicle:instrumented wheelset data and ground wheel-rail force data,a feedforward neural network was employed to calibrate the instrumented wheelset data,referencing the ground wheel-rail force data.Furthermore,ground wheel-rail force data for the locomotive was obtained for the corresponding road section.This data was then integrated with the calibrated instrumented wheelset data from the track inspection vehicle.Leveraging the GNN-LSTM network,the article establishes a mapping relationship model between the wheel-rail force of the track inspection vehicle and the locomotive wheel-rail force.This model facilitates continuous measurement of locomotive wheel-rail forces across three typical scenarios:straight sections,long and steep downhill sections,and small curve radius sections.

Scheme of negative acoustic radiation force based on a multiple-layered spherical structure

Acoustic radiation force(ARF), as an important particle manipulation method, has been extensively studied in recent years. With the introduction of the concept of “acoustic tweezers”, negative acoustic radiation has become a research hotspot. In this paper, a scheme of realizing negative ARF based on the multiple-layered spherical structure design is proposed. The specific structure and design idea are presented. Detailed theoretical calculation analysis is carried out.Numerical simulations have been performed to verify the correctness of this prediction. The conjecture that the suppression of backscattering can achieve negative ARF is verified concretely, which greatly expands the application prospect and design ideas of the ARF. This work has laid a theoretical foundation for realizing precise control of the structure.

Dynamic-based model for calculating the boulder impact force in debris flow

The boulder impact force in debris flow is generally calculated by static methods such as the cantilever beam models.However,these methods cannot describe the dynamic scenario of boulder collision on structures,so the inertia and damping effects of the structures are not involved causing an overestimation on the boulder impact force.In order to address this issue,a dynamic-based model for calculating the boulder impact force of a debris flow was proposed in this study,and the dynamic characteristics of a cantilever beam with multiple degrees of freedom under boulder collision were investigated.By using the drop-weight method to simulate boulders within debris flow,seven experiments of drop-weight impacting the cantilever beam were used to calibrate the error of the dynamicbased model.Results indicate that the dynamic-based model is able to reconstruct the impact force history on the cantilever beam during impact time and the error of dynamic-based model is 15.3%in calculating boulder impact force,significantly outperforming the cantilever beam model’s error of 285%.Therefore,the dynamic-based model can overcome the drawbacks of the static-based models and provide a more reliable theoretical foundation for the engineering design of debris flow control structures.

Experimental Study on the Electrochemical Performance of PEMFC under Different Assembly Forces

Proton exchange membrane fuel cell(PEMFC)is of paramount significance to the development of clean energy.The components of PEMFC are assembled using many pairs of nuts and bolts.The assembly champing bolt torque is critical to the electrochemical performance and mechanical stability of PEMFC.In this paper,a PEMFC with the threechannel serpentine flow field was used and studied.The different assembly clamping bolt torques were applied to the PEMFC in three uniform assembly bolt torque and six non-uniform assembly bolt torque conditions,respectively.And then,the electrochemical performance experiments were performed to study the effect of the assembly bolt torque on the electrochemical performance.The test results show that the assembly bolt torque significantly affected the electrochemical performance of the PEMFC.In uniform assembly bolt torque conditions,the maximal power density increased initially as the assembly bolt torque increased,and then decreased on further increasing the assembly torque.It existed the optimum assembly torque which was found to be 3.0 N·m in this work.In non-uniform assembly clamping bolt torque conditions,the optimum electrochemical performance appeared in the condition where the assembly torque of each bolt was closer to be 3.0 N·m.This could be due to the change of the contact resistance between the gas diffusion layer and bipolar plate and mass transport resistance for the hydrogen and oxygen towards the catalyst layers.This work could optimize the assembly force conditions and provide useful information for the practical PEMFC stack assembly.

Effect of preload forces on multidimensional signal dynamic behaviours for battery early safety warning

Providing early safety warning for batteries in real-world applications is challenging.In this study,comprehensive thermal abuse experiments are conducted to clarify the multidimensional signal evolution of battery failure under various preload forces.The time-sequence relationship among expansion force,voltage,and temperature during thermal abuse under five categorised stages is revealed.Three characteristic peaks are identified for the expansion force,which correspond to venting,internal short-circuiting,and thermal runaway.In particular,an abnormal expansion force signal can be detected at temperatures as low as 42.4°C,followed by battery thermal runaway in approximately 6.5 min.Moreover,reducing the preload force can improve the effectiveness of the early-warning method via the expansion force.Specifically,reducing the preload force from 6000 to 1000 N prolongs the warning time(i.e.,227 to 398 s)before thermal runaway is triggered.Based on the results,a notable expansion force early-warning method is proposed that can successfully enable early safety warning approximately 375 s ahead of battery thermal runaway and effectively prevent failure propagation with module validation.This study provides a practical reference for the development of timely and accurate early-warning strategies as well as guidance for the design of safer battery systems.