Ti_(2)AlNb-based alloy was joined in a continuous drive friction welding machine under different rotational rates(500,1000 and 1500 r/min).The microstructure and mechanical properties of the joints were investigated.I...Ti_(2)AlNb-based alloy was joined in a continuous drive friction welding machine under different rotational rates(500,1000 and 1500 r/min).The microstructure and mechanical properties of the joints were investigated.It is shown that the weld zone(WZ) is fully composed of recrystallized B2 phase,and the grain size decreases with increasing rotational rate.The thermo-mechanically affected zone(TMAZ) suffers severe deformation during welding,due to which most of original precipitation phase is dissolved and streamlines are present.In the heat affected zone(HAZ),only the fine O phase is dissolved.The as-welded joint produced using 1000 r/min has the best mechanical properties,whose strength and elongation are both close to those of the base metal,while the as-welded joint obtained using 500 r/min exhibits the worst mechanical properties.Post-weld annealing treatment annihilates the deformation microstructure and fine O phase precipitates in the joints,consequently improving the mechanical properties significantly.Decomposed α_(2) phase is a weakness for the mechanical performance of the joint since microcracks are apt to form in it in the tensile test.展开更多
The Ti_(2)AlNb alloy was joined with TC4 alloy by vacuum diffusion bonding.The relationship between bonding parameters,and joint microstructure and shear strength was investigated.The results indicated that the diffus...The Ti_(2)AlNb alloy was joined with TC4 alloy by vacuum diffusion bonding.The relationship between bonding parameters,and joint microstructure and shear strength was investigated.The results indicated that the diffusion of Al,Ti,Nb and V elements across bonding interface led to the formation of three reaction layers:B2/βlayer andα2 layer on the TC4 side,andα2+B2/βlayer on the Ti_(2)AlNb side.The bonding temperature determined the atomic activity,thus controlling the growth of reaction layers and influencing the shear strength of the joint.When the Ti_(2)AlNb alloy and TC4 alloy were bonded at 950℃for 30 min under 10 MPa,the shear strength of the joint reached the maximum of 467 MPa.The analysis on the fracture morphology showed that the fracture occurred within the B2/βlayer and the fracture model was ductile rupture.Meanwhile,the formation mechanism of the Ti_(2)AlNb/TC4 joint was discussed in depth.展开更多
Ti_(2)AlNb基合金由于具有优异的高温比强度、高温抗蠕变性能和较高的断裂韧度,因而被认为是替代传统镍基高温合金最具潜力的材料。采用电子束选区熔化(selective electron beam melting,SEBM)技术成形Ti-22Al-25Nb合金,通过工艺优化获...Ti_(2)AlNb基合金由于具有优异的高温比强度、高温抗蠕变性能和较高的断裂韧度,因而被认为是替代传统镍基高温合金最具潜力的材料。采用电子束选区熔化(selective electron beam melting,SEBM)技术成形Ti-22Al-25Nb合金,通过工艺优化获得高致密度(5.42-5.43 g/cm^(3))的成形试样。研究了沉积态和热等静压(hot isostatic pressing,HIP)态试样的显微组织演变、物相演变及其对力学性能的影响。结果表明:沉积态和HIP态组织呈现出沿成形方向的柱状晶结构,且均由B2,O和α_(2)相组成,沉积态试样中的O/α_(2)相自上而下逐渐增加,HIP后组织趋于均匀化,且相对沉积态,析出相的宽度缩小、数量减少。沉积态试样中析出相较多的下部区域具有更高的显微硬度((345.87±5.09)HV),HIP后试样硬度值增加至388.91-390.48HV。沉积态试样室温抗拉强度和伸长率分别为(1061±23.71)MPa和(3.67±1.15)%,HIP后抗拉强度增加至(1101±23.07)MPa,伸长率降低至3.5%。展开更多
基金the financial supports from the Science and Technology Special Project, China (No. K19168)the National Science and Technology Major Project of China (No. 2017-VI-0004-0075)the National Natural Science Foundation of China (No. 52231002)。
文摘Ti_(2)AlNb-based alloy was joined in a continuous drive friction welding machine under different rotational rates(500,1000 and 1500 r/min).The microstructure and mechanical properties of the joints were investigated.It is shown that the weld zone(WZ) is fully composed of recrystallized B2 phase,and the grain size decreases with increasing rotational rate.The thermo-mechanically affected zone(TMAZ) suffers severe deformation during welding,due to which most of original precipitation phase is dissolved and streamlines are present.In the heat affected zone(HAZ),only the fine O phase is dissolved.The as-welded joint produced using 1000 r/min has the best mechanical properties,whose strength and elongation are both close to those of the base metal,while the as-welded joint obtained using 500 r/min exhibits the worst mechanical properties.Post-weld annealing treatment annihilates the deformation microstructure and fine O phase precipitates in the joints,consequently improving the mechanical properties significantly.Decomposed α_(2) phase is a weakness for the mechanical performance of the joint since microcracks are apt to form in it in the tensile test.
基金This work was supported by the National Natural Science Foundation of China(No.51905055)the Natural Science Foundation of Chongqing,China(No.cstc2020jcyj-msxmX0115)the Fundamental Research Funds for the Central Universities,China(No.2020CDJ-LHZZ-086).
文摘The Ti_(2)AlNb alloy was joined with TC4 alloy by vacuum diffusion bonding.The relationship between bonding parameters,and joint microstructure and shear strength was investigated.The results indicated that the diffusion of Al,Ti,Nb and V elements across bonding interface led to the formation of three reaction layers:B2/βlayer andα2 layer on the TC4 side,andα2+B2/βlayer on the Ti_(2)AlNb side.The bonding temperature determined the atomic activity,thus controlling the growth of reaction layers and influencing the shear strength of the joint.When the Ti_(2)AlNb alloy and TC4 alloy were bonded at 950℃for 30 min under 10 MPa,the shear strength of the joint reached the maximum of 467 MPa.The analysis on the fracture morphology showed that the fracture occurred within the B2/βlayer and the fracture model was ductile rupture.Meanwhile,the formation mechanism of the Ti_(2)AlNb/TC4 joint was discussed in depth.
