High-efficiency perovskite solar cells（PSCs） reported hitherto have been mostly prepared in a moisture and oxygen-free glove-box atmosphere, which hampers upscaling and real-time performance assessment of this excit...High-efficiency perovskite solar cells（PSCs） reported hitherto have been mostly prepared in a moisture and oxygen-free glove-box atmosphere, which hampers upscaling and real-time performance assessment of this exciting photovoltaic technology. In this work, we have systematically studied the feasibility of allambient-processing of PSCs and evaluated their photovoltaic performance. It has been shown that phasepure crystalline tetragonal MAPbI;perovskite films are instantly formed in ambient air at room temperature by a two-step spin coating process, undermining the need for dry atmosphere and post-annealing.All-ambient-processed PSCs with a configuration of FTO/TiO;/MAPbI;/Spiro-OMeTAD/Au achieve opencircuit voltage（990 mV） and short-circuit current density（20.31 mA/cm;） comparable to those of best reported glove-box processed devices. Nevertheless, device power conversion efficiency is still constrained at 5% by the unusually low fill-factor of 0.25. Dark current–voltage characteristics reveal poor conductivity of hole-transporting layer caused by lack of oxidized spiro-OMe TAD species, resulting in high seriesresistance and decreased fill-factor. The study also establishes that the above limitations can be readily overcome by employing an inorganic p-type semiconductor, copper thiocyanate, as ambient-processable hole-transporting layer to yield a fill-factor of 0.54 and a power conversion efficiency of 7.19%. The present findings can have important implications in industrially viable fabrication of large-area PSCs.展开更多
The forming mechanism of hole flanging on a thick-wall heavy cylinder forging is simulated by DEFORM3D. The cylinder is 4 390 mm in diameter and 390 mm in thickness. The results show that the compound deformation with...The forming mechanism of hole flanging on a thick-wall heavy cylinder forging is simulated by DEFORM3D. The cylinder is 4 390 mm in diameter and 390 mm in thickness. The results show that the compound deformation with bending and expanding happens in the process of hole flanging. The diameter of pre-hole of the workpiece is one of the key parameters in the process of hole flanging. The optimal diameter is obtained for reverse-conical hole of average diameter 40 mm by simulation of hole flanging process on 5 pre-holes with different diameters and 3 pre-holes with different shapes. The results can provide the scientific base for engineering application of the process.展开更多
A reliable method non-destructive X-ray test of wood defects with computer digital image processing technique was presented in the paper which made the knot-hole in wood clear and easily recognized. It was the first t...A reliable method non-destructive X-ray test of wood defects with computer digital image processing technique was presented in the paper which made the knot-hole in wood clear and easily recognized. It was the first time to use maximtun entropy to determine the threshold of binary picture and thc result was satisfying. The improved Robert was used in the paper in the paper to outline the knot-hole so that the processing was almost on real time.展开更多
With permanent down-hole gauges （PDGs） widely installed in oilfields around the world in recent years, a continuous stream of transient pressure data in real time is now available, which motivates a new round of res...With permanent down-hole gauges （PDGs） widely installed in oilfields around the world in recent years, a continuous stream of transient pressure data in real time is now available, which motivates a new round of research interests in further developing pressure transient processing and analysis techniques. Transient pressure measurements from PDG are characterized by long term and high volume data. These data are recorded under unconstrained circumstances, so effects due to noise, rate fluctuation and interference from other wells cannot be avoided. These effects make the measured pressure trends decline or rise and then obscure or distort the actual flow behavior, which makes subsequent analysis difficult. In this paper, the problems encountered in analysis of PDG transient pressure are investigated. A newly developed workflow for processing and analyzing PDG transient pressure data is proposed. Numerical well testing synthetic studies are performed to demonstrate these procedures. The results prove that this new technique works well and the potential for practical application looks very promising.展开更多
Blazars are characterized by large intensity and spectral variations across the electromagnetic spectrum It is believed that jets emerging from them are almost aligned with the line-of-sight. The major- ity of identif...Blazars are characterized by large intensity and spectral variations across the electromagnetic spectrum It is believed that jets emerging from them are almost aligned with the line-of-sight. The major- ity of identified extragalactic sources in γ-ray catalogs of EGRET and Fermi are blazars. Observationally, blazars can be divided into two classes： fiat spectrum radio quasars （FSRQs） and BL Lacs. BL Lacs usually exhibit lower γ-ray luminosity and harder power law spectra at γ-ray energies than FSRQs. We attempt to explain the high energy properties of FSRQs and BL Lacs from Fermi γ-ray space telescope observations. It was argued previously that the difference in accretion rates is mainly responsible for the large mismatch in observed luminosity in ＂7-ray. However, when intrinsic luminosities are derived by correcting for beaming effects, this difference in 7-ray luminosity between the two classes is significantly reduced. In order to ex- plain this difference in intrinsic luminosities, we propose that spin plays an important role in the luminosity distribution dichotomy of BL Lacs and FSRQs. As the outflow power of a blazar increases with increasing spin of a central black hole, we suggest that the spin plays a crucial role in making BL Lac sources low luminous and slow rotators compared to FSRQ sources.展开更多
The object of this work is to investigate the influence of process parameters on drilling characteristics of an Al 1050 sheet with a thickness of 0.2 mm using a pulsed Nd:YAG laser through numerical analyses and exper...The object of this work is to investigate the influence of process parameters on drilling characteristics of an Al 1050 sheet with a thickness of 0.2 mm using a pulsed Nd:YAG laser through numerical analyses and experiments. By comparing the numerical analyses with the experiments, a proper numerical model was obtained. From the results of the numerical analyses and the experiments, the effects of process parameters on entrance diameters of drilled holes, shapes of the holes, taper angles of the holes and temperature distributions in the vicinity of the holes were examined quantitatively. In addition, the optimal drilling condition was estimated to improve the quality of the drilled holes.展开更多
In this paper, spectral hole depth dependence on temperature below 10 K in Tm^3＋ ：YAG crystal is investigated in detail. A novel model is proposed to analyze the temperature dependence on the spectral hole. By using...In this paper, spectral hole depth dependence on temperature below 10 K in Tm^3＋ ：YAG crystal is investigated in detail. A novel model is proposed to analyze the temperature dependence on the spectral hole. By using the proposed model, we theoretically deduce the temperature dependence of spectral hole depth. The results are compared with experimental results and they are in good agreement. According to the theoretic results, the optimum temperature in experiment can be found.展开更多
In order to meet the rapid needs of processing square hole in mechanical equipment, the paper expounds the square hole processing method： planetary wheel method, and analyze the principle of tooling structure and pro...In order to meet the rapid needs of processing square hole in mechanical equipment, the paper expounds the square hole processing method： planetary wheel method, and analyze the principle of tooling structure and process with computer graphics parameters design. The results that, as long as the appropriate parameters, using the above method not only can punch the square hole, can also be processed triangle, the five angle and hexagonal regular polygon holes. The square hole processing method can provide theoretical basis and engineering reliable reference for related engineering and technical personnel.展开更多
A process capability study is performed for the turning process on a general purpose center lathe in order to verify the process performance and machine ability to perform within specified tolerance limit. The process...A process capability study is performed for the turning process on a general purpose center lathe in order to verify the process performance and machine ability to perform within specified tolerance limit. The process and machine capability indices were measured to determine the process and machine adequacy for industrial application. The tolerance limits were obtained from the given nominal size of the shaft, using the basic hole system and 90 sample shafts were turned on the lathe machine to specification for varying spindle speed and feed rate of the lathe. Three (3) samples were randomly selected for the turning process of a combination of the spindle speed and feed rate as a subgroup size for a total subgroup of thirty (30). The diameters (representing the quality characteristics) were used to generate control charts and capability histogram for the process. The process is within statistical control but found incapable of meeting up to specification because the capability index (C<sub>p</sub>) measured was less than 1 and the machine capability for industrial application is not adequate.展开更多
文摘High-efficiency perovskite solar cells（PSCs） reported hitherto have been mostly prepared in a moisture and oxygen-free glove-box atmosphere, which hampers upscaling and real-time performance assessment of this exciting photovoltaic technology. In this work, we have systematically studied the feasibility of allambient-processing of PSCs and evaluated their photovoltaic performance. It has been shown that phasepure crystalline tetragonal MAPbI;perovskite films are instantly formed in ambient air at room temperature by a two-step spin coating process, undermining the need for dry atmosphere and post-annealing.All-ambient-processed PSCs with a configuration of FTO/TiO;/MAPbI;/Spiro-OMeTAD/Au achieve opencircuit voltage（990 mV） and short-circuit current density（20.31 mA/cm;） comparable to those of best reported glove-box processed devices. Nevertheless, device power conversion efficiency is still constrained at 5% by the unusually low fill-factor of 0.25. Dark current–voltage characteristics reveal poor conductivity of hole-transporting layer caused by lack of oxidized spiro-OMe TAD species, resulting in high seriesresistance and decreased fill-factor. The study also establishes that the above limitations can be readily overcome by employing an inorganic p-type semiconductor, copper thiocyanate, as ambient-processable hole-transporting layer to yield a fill-factor of 0.54 and a power conversion efficiency of 7.19%. The present findings can have important implications in industrially viable fabrication of large-area PSCs.
文摘The forming mechanism of hole flanging on a thick-wall heavy cylinder forging is simulated by DEFORM3D. The cylinder is 4 390 mm in diameter and 390 mm in thickness. The results show that the compound deformation with bending and expanding happens in the process of hole flanging. The diameter of pre-hole of the workpiece is one of the key parameters in the process of hole flanging. The optimal diameter is obtained for reverse-conical hole of average diameter 40 mm by simulation of hole flanging process on 5 pre-holes with different diameters and 3 pre-holes with different shapes. The results can provide the scientific base for engineering application of the process.
文摘A reliable method non-destructive X-ray test of wood defects with computer digital image processing technique was presented in the paper which made the knot-hole in wood clear and easily recognized. It was the first time to use maximtun entropy to determine the threshold of binary picture and thc result was satisfying. The improved Robert was used in the paper in the paper to outline the knot-hole so that the processing was almost on real time.
基金Science Foundation of China University of Petroleum, Beijing (No.YJRC-2011-02)for the financial support during this research
文摘With permanent down-hole gauges （PDGs） widely installed in oilfields around the world in recent years, a continuous stream of transient pressure data in real time is now available, which motivates a new round of research interests in further developing pressure transient processing and analysis techniques. Transient pressure measurements from PDG are characterized by long term and high volume data. These data are recorded under unconstrained circumstances, so effects due to noise, rate fluctuation and interference from other wells cannot be avoided. These effects make the measured pressure trends decline or rise and then obscure or distort the actual flow behavior, which makes subsequent analysis difficult. In this paper, the problems encountered in analysis of PDG transient pressure are investigated. A newly developed workflow for processing and analyzing PDG transient pressure data is proposed. Numerical well testing synthetic studies are performed to demonstrate these procedures. The results prove that this new technique works well and the potential for practical application looks very promising.
基金partially supported by projects SB/S2HEP-001/2013funded by DST(DB)+1 种基金ISRO/RES/2/367/10-11funded by ISRO,India
文摘Blazars are characterized by large intensity and spectral variations across the electromagnetic spectrum It is believed that jets emerging from them are almost aligned with the line-of-sight. The major- ity of identified extragalactic sources in γ-ray catalogs of EGRET and Fermi are blazars. Observationally, blazars can be divided into two classes： fiat spectrum radio quasars （FSRQs） and BL Lacs. BL Lacs usually exhibit lower γ-ray luminosity and harder power law spectra at γ-ray energies than FSRQs. We attempt to explain the high energy properties of FSRQs and BL Lacs from Fermi γ-ray space telescope observations. It was argued previously that the difference in accretion rates is mainly responsible for the large mismatch in observed luminosity in ＂7-ray. However, when intrinsic luminosities are derived by correcting for beaming effects, this difference in 7-ray luminosity between the two classes is significantly reduced. In order to ex- plain this difference in intrinsic luminosities, we propose that spin plays an important role in the luminosity distribution dichotomy of BL Lacs and FSRQs. As the outflow power of a blazar increases with increasing spin of a central black hole, we suggest that the spin plays a crucial role in making BL Lac sources low luminous and slow rotators compared to FSRQ sources.
基金supported by a grant-in-aid of Regional Innovation Center(RIC),New Technology Development and Research Center of Laser Application in Chosun University,Korea.
文摘The object of this work is to investigate the influence of process parameters on drilling characteristics of an Al 1050 sheet with a thickness of 0.2 mm using a pulsed Nd:YAG laser through numerical analyses and experiments. By comparing the numerical analyses with the experiments, a proper numerical model was obtained. From the results of the numerical analyses and the experiments, the effects of process parameters on entrance diameters of drilled holes, shapes of the holes, taper angles of the holes and temperature distributions in the vicinity of the holes were examined quantitatively. In addition, the optimal drilling condition was estimated to improve the quality of the drilled holes.
基金supported by the National Natural Science Foundation of China (Grant No. 11004152)the Science Fund of Tianjin Education Commission (Grant Nos. 20090715 and 20110704)
文摘In this paper, spectral hole depth dependence on temperature below 10 K in Tm^3＋ ：YAG crystal is investigated in detail. A novel model is proposed to analyze the temperature dependence on the spectral hole. By using the proposed model, we theoretically deduce the temperature dependence of spectral hole depth. The results are compared with experimental results and they are in good agreement. According to the theoretic results, the optimum temperature in experiment can be found.
文摘In order to meet the rapid needs of processing square hole in mechanical equipment, the paper expounds the square hole processing method： planetary wheel method, and analyze the principle of tooling structure and process with computer graphics parameters design. The results that, as long as the appropriate parameters, using the above method not only can punch the square hole, can also be processed triangle, the five angle and hexagonal regular polygon holes. The square hole processing method can provide theoretical basis and engineering reliable reference for related engineering and technical personnel.
文摘A process capability study is performed for the turning process on a general purpose center lathe in order to verify the process performance and machine ability to perform within specified tolerance limit. The process and machine capability indices were measured to determine the process and machine adequacy for industrial application. The tolerance limits were obtained from the given nominal size of the shaft, using the basic hole system and 90 sample shafts were turned on the lathe machine to specification for varying spindle speed and feed rate of the lathe. Three (3) samples were randomly selected for the turning process of a combination of the spindle speed and feed rate as a subgroup size for a total subgroup of thirty (30). The diameters (representing the quality characteristics) were used to generate control charts and capability histogram for the process. The process is within statistical control but found incapable of meeting up to specification because the capability index (C<sub>p</sub>) measured was less than 1 and the machine capability for industrial application is not adequate.
