Effect of a homogeneous recrystallized microstructure and a bimodal microstructure on mechanical properties in Mg-5Zn-0.6Zr alloys

For typical Mg-Zn-Zr alloys,exhilaratingly high strength of a yield strength(YS)higher than 300 MPa can hardly be attained by traditional rolling.In this paper,we compare the mechanical properties and strengthening mecha-nisms of the Mg-5Zn-0.6Zr alloys having a homogeneous dynamical recrystallized microstructure and a bimodal microstructure with high-density nano substructures.The Mg-5Zn-0.6Zr alloy with the bimodal microstructure(rolled at 150℃ with a thickness reduction of 60%)exhibits a YS of 332 MPa,an ultimate tensile strength(UTS)of 360 MPa,and an elongation of 5%.The high strength is attributed to the microstructure with high-density nano substructures,high-density nano(Mg,Zr)Zn_(2) precipitates,ultrafine recrystallized grains,and strong basal texture.In comparison,the Mg-5Zn-0.6Zr alloy with homogeneous microstructure(rolled at 200℃ with a thick-ness reduction of 70%)exhibits a YS of 209 MPa,an UTS of 317 MPa,and an elongation of 17%,which contains coarser recrystallized grains,coarser precipitates,weaker texture,and lower density of dislocations,further re-sulting in low strength.The difference between the strengthening mechanism in two kinds of microstructure is discussed in detail.The results facilitate the preparation of wrought Magnesium alloy with high strength by reasonable microstructure construction.

Fractal Characteristics and Prediction of Ti-15-3 Alloy Recrystallized Microstructure

Grain shape of the hot deforming alloy is an important of material. The fractal theory was applied to analyze index to character the microstructure and performance the recrystallized microstructure of Ti-15-3 alloy after hot deformation and solution treatment. The fractal dimensions of recrystallized grains were calculated by slit island method. The influence of processing parameters on fractal dimension and grain size was studied, It has been shown that the shapes of recrystallized grain boundaries are self-similar, and the fractal dimension varies from 1 to 2. With increasing deformation degree and strain rate or decreasing deformation temperature, the fractal dimension of grain boundaries increased and the grain size decreased. So the fractal dimension could characterize the grain shape and size. A neural network model was trained to predict the fractal dimension of recrystallized microstructure and the result is in excellent agreement with the experimental data.

Progress in Recrystallized SiC and Its Composites

Recrystallized silicon carbide（ RSi C）,a high purity Si C material sintered by the process of evaporation-condensation without any additives,is one of the most important structural materials in the fields of high temperatures. However,its low density and porous structure caused by the sintering mechanism in the absence of shrinkage,restrict its wide applications in engineering.This paper reviews the research progress and related technologies on the preparation of high-density RSi C and its composites. RSi C with relative high density up to 2. 75g·cm- 3can be obtained by a combination of pretreatment to Si C raw materials such as reshaping,modification and particle size distribution,and appropriate forming method. Post treatments such as cyclic pyrolysis and impregnation- recrystallization,and slurry impregnation- recrystallization are needed for the further density increase of RSi C（ 2. 99 g·cm- 3）. In addition,high performance RSi C- Mo Si2 and RSi C- Al composites obtained by melt infiltration are also reviewed.

Influence of rolling parameters on dynamically recrystallized microstructures in AZ31 magnesium alloy sheets

Conventional rolling experiments via the embedded pin in rolling sheet method were carried out at different reduction rates,starting rolling temperatures,and rolling speeds,and the effects of rolling parameters(i.e.,temperature,equivalent strain,and rolling time)on dynamically recrystallized(DRX)microstructures of AZ31 alloy during hot rolling were studied quantitatively.The temperature-strain dependence of the high-angle grain boundary fraction(HAGB%)was examined through electron backscattered diffraction.Results showed that as-rolled microstructures with high HAGB%may be obtained under average rolling temperatures of 270-320℃,equivalent strains higher than 0.8,and a rolling speed of 246 mm/s.These results may be related to the DRX kinetics and dynamic recovery which are controlled by deformation temperature and strain.HAGB%decreased with increasing rolling time(decreasing rolling speed),which is attributed to dynamic recovery,and the recrystallized grain size decreased as rolling time increased.However,further increases in rolling time increased average grain sizes but decreased mean subgrain sizes;these results are attributed to increases in the low-angle grain boundary(LAGB)length per unit area with rolling time.LAGB formation was controlled by dynamic recovery,which consistently follows polygonization or formation of new subgrains inside larger grains;hence,average subgrain sizes decreased with the rolling time.The effect of dynamic recovery on HAGB and LAGB formation and their related mechanisms over a wide range of strains and temperatures were discussed in detail.

Effects of dynamic recrystallization and strain-induced dynamic precipitation on the corrosion behavior of partially recrystallized Mg-9Al-lZn alloys

The corrosion susceptibility of recrystallized and un-recrystallized grains in equal channel angular pressed(ECAPed)Mg-9Al-lZn(AZ91)alloys immersed in chloride containing media was investigated through immersion testing and an electrochemical microcell technique coupledwith high resolution techniques such as scanning Kelvin probe force microscopy(SKPFM),transmission electron microscopy(TEM),andelectron backscatter diffraction(EBSD).During ECAP,dynamic recrystallization(DRX)and strain-induced dynamic precipitation(SIDP)simultaneously occurred,resulting in a bimodal grain structure of original elongated coarse grains and newly formed equiaxed fine grainswith a large volume fraction ofβ-Mg17Al12 precipitates.Corrosion preferentially initiates and propagates in the DRXed grains,owing tothe greater microchemistry difference between theβ-Mg17Al12 precipitates formed at the DRXed grain boundaries and the adjacentα-Mgmatrix,which induces a strong microgalvanic coupling between these phases.Additionally,the weaker basal texture of the DRXed grainsalso makes these grains more susceptible to electrochemical reactions than the highly textured un-DRXed grains.The influence of dynamicrecrystallization and dynamic precipitation was also studied in ECAPed alloys with differenl levels of deformation strain through corrosion andelectrochemical techniques.Increasing the strain level led to a more uniform corrosion with a shallow penetration depth,lower corrosion ratevalues,and higher protective ability of the oxide film.Furthermore,higher levels of strain resulted in greater hardness values of the ECAPedalloys.The superior corrosion resistance and strength of the ECAPed alloys with increasing strain level was attributed to the combination ofsmaller DRXed grain size,higher DRX ratio,and higher volume fraction of uniformly distributed fineβ-Mg17Al12 precipitates.c 2020 Published by Elsevier B.V.on behalf of Chongqing University.

Surface morphology and impurity distribution of electron beam recrystallized silicon films on low cost substrates for solar cell absorber

A line shaped electron beam recrystallised polycrystalline silicon film on the low cost substrate was investigated for the use of the solar cell absorber. The applied EB energy density strongly influences the surface morphology of the film system. Lower EB energy density results in droplet morphology and the rougher SiO2 capping layer due to the low fluidity. With the energy increasing, the capping layer becomes smooth and continuous and less and small pinholes form in the silicon film. Tungstendisilicide (WSi2) is formed at the interface tungsten/silicon but also at the grain boundaries of the silicon. Because of the fast melting and cooling of the silicon film, the eutectic of silicon and tungstendisilicide mainly forms at the grain boundary of the primary silicon dendrites. The SEM-EDX analysis shows that there are no chlorine and hydrogen in the area surrounding a pinhole after recrystallization because of outgassing during the solidification.

Comparative Study on Schizontocidal Activity of Recrystallized or Crude Daphnetin Against Malaria Parasites

Objective To compare the schizontocidal activity of recrystallized or crude daphnetin against malaria parasites in vivo. Methods Schizontocidal activity of recrystallized or crude daphnetin at various dosages was assessed in mice infected with Plasmodium berghei ANKA using a 4-day suppress assay. Results The comparison of the reduction rate of parasitemia caused by either recrystallized or crude dephnetin showed that ED50 of crude daphnetin was 18.36 mg/kg, with 95% confidence limit of 5.96-56.54 mg/kg while ED50 of recrystallized daphnetin was 11.46 mg/kg, with 95% confidence limit of 8.63-15.22 mg/kg. Conclution The results indicate that the efficacy of recrystallized daphnetin is 37.6% higher than that of crude daphnetin.

Microstructure Evolution and Recrystallized Behavior of Friction Stir Welding Twin-Induced Plasticity Steel

The restoration mechanism of twin-induced plasticity(TWIP)steel during friction stir welding(FSW)changed with the degree of the deformation,and the microstructure evolution and dynamic recrystallization are complex and unclear.In this paper,the electron backscattered diffraction and transmission electron microscopy techniques were used to evaluate the dynamic grain structure of FSW joint of TWIP steel.The results showed that the dynamic recrystallization mechanisms in TWIP steel during FSW contained discontinuous dynamic recrystallization(DDRX)and continuous dynamic recrystallization(CDRX).The recrystallization mechanism transitioned from DDRX at the initial deformation stage to DDRX and CDRX at the middle deformation stage,eventually becoming primarily CDRX at the end deformation stage.Numerous annealing twin boundaries(ATBs)were formed within the joint,and the straight ATBs primarily resulted from grain growth accidents,while cluster-shaped ATBs were formed through re-excitations and decomposition of specific grain boundaries.

深低温保存下高效抗冻多肽的合理设计和机理探讨

The development of effective antifreeze peptides to control ice growth has attracted a significant amount of attention yet still remains a great challenge.Here,we propose a novel design method based on in-depth investigation of repetitive motifs in various ice-binding proteins(IBPs)with evolution analysis.In this way,several peptides with notable antifreeze activity were developed.In particular,a designed antifreeze peptide named AVD exhibits ideal ice recrystallization inhibition(IRI),solubility,and biocompatibility,making it suitable for use as a cryoprotective agent(CPA).A mutation analysis and molecular dynamics(MD)simulations indicated that the Thr6 and Asn8 residues of the AVD peptide are fundamental to its ice-binding capacity,while the Ser18 residue can synergistically enhance their interaction with ice,revealing the antifreeze mechanism of AVD.Furthermore,to evaluate the cryoprotection potential of AVD,the peptide was successfully employed for the cryopreservation of various cells,which demonstrated significant post-freezing cell recovery.This work opens up a new avenue for designing antifreeze materials and provides peptide-based functional modules for synthetic biology.

Predicting recrystallized grain size in friction stir processed 304L stainless steel

A major dilemma faced in the nuclear industry is repair of stainless steel reactor components that have been exposed to neutron irradiation. When conventional fusion welding is used for repair, intergranular cracks develop in the heat-affected zone(HAZ). Friction stir processing(FSP), which operates at much lower peak temperatures than fusion welding, was studied as a crack repair method for irradiated 304 L stainless steel. A numerical simulation of the FSP process in 304 L was developed to predict temperatures and recrystallized grain size in the stir zone. The model employed an Eulerian finite element approach,where flow stresses for a large range of strain rates and temperatures inherent in FSP were used as input. Temperature predictions in three locations near the stir zone were accurate to within 4%, while prediction of welding power was accurate to within 5% of experimental measurements. The predicted recrystallized grain sizes ranged from 7.6 to 10.6 μm, while the experimentally measured grains sizes in the same locations ranged from 6.0 to 7.6 μm. The maximum error in predicted recrystallized grain size was about 39%, but the associated stir zone hardness from the predicted grain sizes was only different from the experiment by about 10%.

Microstructural evolution and dynamic recrystallization mechanisms of additively manufactured TiAl alloy with heterogeneous microstructure during hot compression

Microstructural evolution and dynamic recrystallization(DRX)mechanisms of a Ti-48Al-2Cr-2Nb(at.%)alloy prepared by selective electron beam melting(SEBM)during hot deformation at 1150℃and 0.1 s^(-1)were investigated by hot compression tests,optical microscope(OM),scanning electron microscope(SEM),electron back-scattered diffraction(EBSD)and transmission electron microscope(TEM).The results show that the initial microstructure of the as-SEBMed alloy exhibits layers of coarseγgrains and fineγ+α_(2)+(α_(2)/γ)lamellar mixture grains alternately along the building direction.During the early stage of hot deformation,deformation twins tend to form within the coarse grains,facilitating subsequent deformation,and a small number of DRX grains appear in the fine-grained regions.With the increase of strain,extensive DRX grains are formed through different DRX mechanisms in both coarse and fine-grained regions,involving discontinuous dynamic recrystallization mechanism(DDRX)in the fine-grained regions and a coexistence of DDRX and continuous dynamic recrystallization(CDRX)in the coarsegrained regions.

Refinement Mechanism of Microstructure of Undercooled Nickel Based Alloys

Through the use of purification and recirculation superheating techniques on molten glass,the Ni65Cu33Co2 alloy was successfully undercooled to a maximum temperature of 292 K.High-speed photography was employed to capture the process of interface migration of the alloy liquid,allowing for an analysis of the relationship between the morphological characteristics of the alloy liquid solidification front and the degree of undercooling.Additionally,the microstructure of the alloy was examined using metallographic microscopy,leading to a systematic study of the microscopic morphological characteristics and evolution laws of the refined structure during rapid solidification.The research reveals that the grain refining mechanism of the Ni-Cu-Co ternary alloy is consistent with that of the binary alloy(Ni-Cu).Specifically,under low undercooling conditions,intense dendritic remelting was found to cause grain refinement,while under high undercooling conditions,recrystallization driven by accumulated stress and plastic strain resulting from the interaction between the liquid flow and the primary dendrites caused by rapid solidification was identified as the main factor contributing to grain refinement.Furthermore,the study highlights the significant role of the Co element in influencing the solidification rate and reheat effect of the alloy.The addition of Co was also found to facilitate the formation of non-segregated solidification structure,indicating its importance in the overall solidification process.

Improvement of Microstructure and Mechanical Properties of Rapid Cooling Friction Stir-welded A1050 Pure Aluminum

Two-mm thick A1050 pure aluminum plates were successfully joined by conventional and rapid cooling friction stir welding(FSW), respectively. The microstructure and mechanical properties of the welded joints were investigated by electron backscatter diffraction characterization, Vickers hardness measurements, and tensile testing. The results showed that liquid CO_(2) coolant significantly reduced the peak temperature and increased the cooling rate, so the rapidly cooled FSW joint exhibited fine grains with a large number of dislocations. The grain refinement mechanism of the FSW A1050 pure aluminum joint was primarily attributed to the combined effects of continuous dynamic recrystallization, grain subdivision, and geometric dynamic recrystallization. Compared with conventional FSW, the yield strength, ultimate tensile strength, and fracture elongation of rapidly cooled FSW joint were significantly enhanced, and the welding efficiency was increased from 80% to 93%. The enhanced mechanical properties and improved synergy of strength and ductility were obtained due to the increased dislocation density and remarkable grain refinement. The wear of the tool can produce several WC particles retained in the joint, and the contribution of second phase strengthening to the enhanced strength should not be ignored.

Twinning aspects and their efficient roles in wrought Mg alloys:A comprehensive review

Twinning is widely recognized as an effective and cost-efficient method for controlling the microstructure and properties of wrought magnesium(Mg)alloys.Specifically,twins play a crucial role in initiating dynamic recrystallization(DRX),while twin regions experience rapid recrystallization during static recrystallization(SRX).The activation of twinning can lead to changes in lattice orientation,significantly impacting the final texture in Mg alloys.The active roles of twinning are influenced by various factors during the activation process,and the mobility of twin boundaries(TB)can be amplified by stress effects,dislocation interactions,and thermal effects.Conversely,annealing treatments that involve proper segregation or precipitation on TBs serve to stabilize them,restraining their motion.Events such as segregation may also alter the twinning propensity in Magnesium-rare earth(Mg-RE)alloys.While{10–11}contraction twins(CT)and{10–11}-{10–12}double twins(DT)can promote dynamic recrystallization(DRX),they also pose a risk as potential sources of voids and cracks.Additionally,understanding the nucleation and growth mechanisms of twinning is crucial,and these aspects are briefly reviewed in this article.Considering the factors mentioned above,this article summarizes the recent research progress in this field,shedding light on advancements in recent eras.

Mechanism in Solidification of a Ternary Nickel Based Alloy

The experiment employed the use of melt purification and cyclic superheating technique to achieve maximum undercooling of Ni65Cu31Co4 alloy at 300K.Simultaneously,high-speed photography techniques were used to capture the process of alloy liquid phase interface migration,and analyzed the relationship between the shape characteristics of the front end of alloy solidification and undercooling.The microstructure of the alloy was observed through metallographic microscopy,and the micro-morphological characteristics and evolution of the rapidly solidified microstructure were systematically studied.It is found that the grain refinement mechanism of Ni-Cu-Co ternary alloy is similar to that of Ni-Cu binary alloy.Grain refinement at low undercooling is caused by intense dendritic remelting,while grain refinement at high undercooling is attributed to recrystallization,driven by the stress and plastic strain accumulated from the interaction of liquid flow and primary dendrites caused by rapid solidification.It also shows that the addition of the third element Co plays a significant role in solidification rate and re-ignition effect.

Effect of annealing treatment on the microstructure and mechanical properties of warm-rolled Mg-Zn-Gd-Ca-Mn alloys

The basal texture of traditional magnesium alloy AZ31 is easy to form and exhibits poor plasticity at room temperature.To address these problems,a multi-micro-alloyed high-plasticity Mg-1.8Zn-0.8Gd-0.1Ca-0.2Mn(wt%)alloy was developed using the unique role of rare earth and Ca solute atoms.In addition,the influence of the annealing process on the grain size,second phase,texture,and mechanical properties of the warm-rolled sheet at room temperature was analyzed with the goal of developing high-plasticity mag-nesium alloy sheets and obtaining optimal thermal-mechanical treatment parameters.The results show that the annealing temperature has a significant effect on the microstructure and properties due to the low alloying content:there are small amounts of larger-sized block and long string phases along the rolling direction(RD),as well as several spherical and rodlike particle phases inside the grains.With increas-ing annealing temperature,the grain size decreases and then increases,and the morphology,number,and size of the second phase also change correspondingly.The particle phase within the grains vanishes at 450℃,and the grain size increases sharply.In the full recrystal-lization stage at 300-350℃,the optimum strength-plasticity comprehensive mechanical properties are presented,with yield strengths of 182.1 and 176.9 MPa,tensile strengths of 271.1 and 275.8 MPa in the RD and transverse direction(TD),and elongation values of 27.4%and 32.3%,respectively.Moreover,there are still some larger-sized phases in the alloy that influence its mechanical properties,which offers room for improvement.

An in-situ study of static recrystallization in Mg using high temperature EBSD

It has been a common method to improve the mechanical properties of metals by manipulating their microstructures via static recrystallization,i.e.,through heat treatment.Therefore,the knowledge of recrystallization and grain growth is critical to the success of the technique.In the present work,by using in-situ high temperature EBSD,the mechanisms that control recrystallization and grain growth of an extruded pure Mg were studied.The experimental results revealed that the grains of priority for dynamic recrystallization exhibit fading competitiveness under static recrystallization.It is also found that grain boundary movement or grain growth is likely to show an inverse energy gradient effect,i.e.,low energy grains tend to swallow or grow into high energy grains,and grain boundaries of close to 30°exhibit superior growth advantage to others.Another finding is that{10-12}tensile twin boundaries are sites of hardly observed for recrystallization,and are finally swallowed by adjacent recrystallized grains.The above findings may give comprehensive insights of static recrystallization and grain growth of Mg,and may guide the design of advanced materials processing in microstructural engineering.

Promoting dynamic recrystallization and improving strength and ductility of Mg-7Bi alloy through Al addition

This study investigated the influence of the addition of Al to a Mg-7Bi(B7,wt%)alloy,particularly its recrystallization behavior during extrusion and its resulting mechanical properties.The addition of 2 wt%Al to the B7 alloy resulted in a lower grain size,a reduction in the number density of fine Mg3Bi2 particles,and a higher area fraction of relatively coarse Mg3Bi2 particles in the extrusion billet.These microstructural changes increased the nucleation sites for recrystallization,reduced the Zener pinning effect,and enhanced particle-stimulated nucleation,all of which promoted dynamic recrystallization behavior during extrusion.As a result,the area fraction of recrystallized grains in the extruded alloy increased from 77%to 94%.The extruded B7 alloy exhibited a strong<10-10>fiber texture,whereas the extruded Mg-7Bi-2Al(BA72)alloy had a weak<10-10>-<2-1-10>texture,which was attributed to the minimal presence of unrecrystallized grains and the dispersed orientation of the recrystallized grains.The tensile yield strength(TYS)of the extruded BA72 alloy was higher than that of the extruded B7 alloy(170 and 124 MPa,respectively),which resulted from the enhanced grain-boundary and solid-solution strengthening effects.The tensile elongation(EL)of the BA72 alloy also exceeded that of the B7 alloy(20.3%and 6.1%,respectively),the result of the uniform formation of fine twins under tension in the former and the formation of a few coarse twins among the unrecrystallized grains in the latter.Consequently,the addition of a small amount of Al to the B7 alloy significantly improved both the strength and ductility of the extruded alloy,resulting in a remarkable increase in the product of the TYS and EL from 756 to 3451 MPa%and expanding its potential range of applications as a lightweight extruded structural component.

Effect of Gd Addition on Hot Deformation Behavior and Microstructure Evolution of 7075 Aluminum Alloy

In order to clarify the effect of rare earth Gd on the microstructure evolution and deformation behavior of 7075 aluminum alloy during hot compression,uniaxial compression tests of Al-Zn-Mg-Cu-0.5%Gd were conducted at strain rates of 0.001,0.01,0.1,and 1 s^(-1)with the temperatures ranging from 350 to 450℃.The microstructural evolution during deformation was characterized using optical microscopy and electron backscatter diffraction(EBSD)techniques.The experimental results indicate that the addition of the rare earth element Gd significantly increases the peak flow stress and thermal activation energy of the alloy.Due to the pinning effect of rare earth phases,dislocation movement is hindered,leading to an increased level of work hardening in the alloy.However,the dynamic recrystallization of the alloy is complicated.At a high Z(Zener-Hollomon parameter)values,recrystallization occurs in the form of DDRX(Discontinuous Dynamic Recrystallization),making it easier to nucleate at grain boundaries.As the Z value decreases gradually,the recrystallization mechanism transitions from discontinuous dynamic recrystallization(DDRX)to continuous dynamic recrystallization(CDRX).At a low Z values with the strain rate of 0.001 s^(-1),the inhibitory effect of rare earths weakens,resulting in a comparable recrystallization ratio between Al-Zn-Mg-Cu-Gd alloy and 7075 aluminum alloy.Moreover,the average grain size of the aluminum alloy with Gd addition is only half that of 7075 aluminum.The addition of Gd provides Orowan and substructure strengthening for the alloy,which greatly improves the work-hardening of the alloy compared with 7075 aluminum alloy and improves the strength of the alloy.

The Mechanism of Cube Texture Formation in Ni-7 at%W Substrate

In order to obtain the sharp cube texture,a new process,the intermediate annealing rolling technique,has been introduced to prepare the Ni7W substrate.In this paper,a cubic texture content up to 98.5%within 10°of the standard cubic orientation is obtained in the final substrate and the influence of this improved rolling technique on the cube texture formation has been discussed.The results show that the increased cube texture in the Ni7W substrate is caused by the optimized deformation texture and the increased nucleated fraction of the cube grains.