MUF Resins Improved by Citric Acid as Adhesives for Wood Veneer Panels

This article presents the first applied results of using citric acid in combinations with a melamine-urea-formal-dehyde(MUF)resin for bonding wood veneers.The chemical reactions involved are shown based on a MALDI ToF analysis of the reaction of the MUF resin with citric acid.The preliminary results of the physical and mechanical properties of the LVL prepared are also presented.Veneers from Populus sp were used to manufacture 5-layer laminated veneer lumber(LVL)of small dimensions.Five combinations of the amount of citric acid,MUF spread rate and pressing parameters were tested.LVL bonded with 20%of citric acid+100 g/m^(2)of MUF,hot-pressed using a 3-step process with maximum 1.5 MPa of pressure yielded the board with better dimensional stability and mechanical properties.It could be concluded that citric acid in combination with MUF can be used for bonding wood veneer and the research should be continued to study further the parameters involved and to enhance the results.

Using optical coherence tomography images to evaluate fungal growth in reline resins

As changes in hard or soft oral tissues normally have a microbiological component,it is important to develop diagnostic techniques that support clinical evaluation,without destroying microbio-logical formation.The optical coherence tomography(OCT)represents an alternative to analyze tissues and microorganisms without the need for processing.This imaging technique could be defined as a fast,real-time,in situ,and non-destructive method.Thus,this study proposed the use of the OCT to visualize biofilm by Candida albicans in reline resins for removable prostheses.Three reline resins(Silagum-Comfort,Coe Comfort,and Soft-Confort),with distinct char-acteristics related to wa ter sorption and fungal inhibition were used.A total of 30 samples(10 for each resin group)were subjected to OCT scanning before and 96 h after inoculation with Candida albicans(URM 6547).The biofilm analysis was carried out through a 2D optical Callisto SD-OCT(930 nm)operated in the spectral domain.Then,the images were preprocessed using a3×3 Gaussian filter to remove the noise,and then Otsu binarization,allowing segmentation and pixel counting.The layer's biofilm formed was clearly defined and,indeed,its visualization is modified by water sorption of each material.Silagum-Comfort and Soft.Confort showed some similarities in the scattering of light between the clean and inoculated samples,in which,the latter samples presented higher values of light signal intensity.Coe-Comfort samples were the only ones that showed no di®erences between the clean or inoculated images.Therefore,the results of this study suggest that OCT is a viable technique to visualize the biolm in reline materials.Becausendings in the literature are still scarcely using the OCT technique to visualize biolm in reline resins,further studies are encouraged.It should not contain any references or displayed equations.

Room-Temperature Phosphorescence and Lifetime of Fossil Resins (Amber) from Dominican Republic, Mexico, Baltic Sea, Myanmar, and Fushun, China

Amber can emit room temperature phosphorescence(RTP)under the well-known 365 nm fluorescence ultraviolet light.This paper is devoted to the phosphorescence study of 20 pieces of amber materials from the Dominican Republic,Mexico,Baltic sea,Myanmar,and Fushun,China.The results show that amber from the same geographic origin has similar shape in phosphorescence spectra.However,the shape of the amber phosphorescence spectra varies depending on their different localities.Burmite(amber from Myanmar)and Fushun amber have a bright yellow phosphorescence with a long lifetime,while the Dominican and Mexican ones are weaker and last shorter.The irradiation of Baltic amber becomes faint or even inert.Phosphorescence spectral Gaussian fitting results suggest an emission maximum near 550 nm in most amber samples.Their phosphorescence lifetime,analyzed through the exponential function fitting,is up to 1 second in Burmite and Fushun samples,shorter in the Dominican and Mexican ones,about 0.230 s,and the shortest in Baltic amber,close to 0.151 s.These variations of phosphorescence lifetime and intensity are related to the relative geological ages of these amber.It indicated that the phosphorescence agent was probably formed during the long geological time.While the anomaly occurred in Baltic amber,the only one found in a sea secondary deposit form,it demonstrated that the terrestrial geological environment these amber preserved has prevented the phosphorescence agent to be deactivated.

Synthesis and Characterization of Cured Allyl/Propargyl Ether Novolac Resins

A new kind of modified thermoset resins were synthesized by phase-transfer Williamson reaction from novolac resin and mixtures of allyl- and propargyl-chlorides. The compositions of the resins were defined by 1H NMR （nuclear magnetic resonanse） spectroscopy and the dependence of the cured materials properties on the composition was established. Increase of a propargyl content resulted in char yield raise and the maximum value had been found for propargylated resin--58%. DSC （differential scanning calorimetry）-analysis of the resins has demonstrated that exothermic enthalpy of the curing process could be adjusted by varying the content of propargyl and allyl groups in the resin.

Preparation of Aminated Macroporous Polyvinyl Alcohol Resins and Evaluation for Bilirubin Adsorption

In the present study we prepared macroporous polyvinyl alcohol beads. A series of bilirubin adsorbents were generated by immobilization of eight amine agents to the beads as ligands. The adsorption of bilirubin was evaluated by in vitro static and dynamic adsorption tests. The results show that these adsorbents have excellent adsorption efficiency and capacity. Among the eight ligands, trimethylamine （TMA）, triethylamine （TEA） and 1,6- hexanediamine （HDA） showed the highest adsorption capacity. The adsorption equilibrium can be achieved in half an hour, and the adsorption percentage of bilirubin was up to 80%. Static electricity and hydrophobie interaction played the main role in bilirubin adsorption, and the adsorption was found to match the monolayer model. The excellent adsorption of these adsorbents indicates their potential in clinical treatment.

SYNTHESIS，REGENERATION AND APPLICATIONOF SORPTION RESINS

By means of the synthetic approach of non－polar or weak polar oil－sorbed polymers，the gel sorption resin（GSR） and the multiporous sorption resin（MSR） were prepared．The structure of the resins，sorption power，sorption speed，desorption，and sorption of organic compounds from sewage，exhaust gas and soil were discussed．Moreover，the resins were used to decrease LOD and BOD5 values of water waste from sewage factory．Theyare a klndof potential materials for environmental control．

Hydrolysis Activities of Resins of Complexes Made from Polysaccharides and Ce^(4+)

Resins of complexes made from agarose-Ce4+ (RCA-Ce) and chitosan-Ce4+ (RCC-Ce) were prepared. Hydrolysis rates of methamidophos, omethoate and chlorpyrifos treated by RCA-Ce were 32.39%, 27. 12% and 46.62%, respectively, those of chlorpyrifos and methamidophos in mung bean sprout juice 38.28% and 35.45% , and that of chlorpyrifos in tea extract 59.76% . Hydrolysis rates of protein in tea extract treated by RCA-Ce increased by 86.46% . RCC-Ce could be employed in the apple juice production. The contents of methamidophos and parathion-methyl in the juice treated by RCC-Ce decreased 58.76% and 71.92% . Furthermore, RCC-Ce was used to clarification for beer by the ways of a column. RCC-Ce could hydrolyze sensitive protein and increase contents of free amino acid in the beer. Therefore, the beer treated by RCC-Ce could stay oxidation and aging procedure due to some metal ions being absorbed by RCC-Ce.

A discussion on producing agro-residue composites with isocyanate resins

With the urgent shortage of forest resource in China, using agro-residues as raw materials of composite become increasingly important. Agro-residue is the most potential fiber resource, which is helpful to sustainable development of composite industries in China. Based on a great deal of researches, this paper summarized and discussed some problems in using agro-residues as raw materials of composites, including raw material preparation, hot-pressing, bonding technology, preventing composite from going moldy. It is proposed that to manufacture the composite of rice straws or wheat straws, the isocayante resin is a suitable adhesive, and the appropriate technologies, bonding, and treatment measures are also needed.

Development of Prolonged Release Microspheres of Metformin Hydrochloride Using Ion Exchange Resins

Aim To prepare the prolonged-released microspheres of mefformin hydrochloride. Methods Ion-exchange resin-drug mefformin hydrochloride complexes were prepared as core materials, and followed by coating using ethylcellulose （EC） by the emulsion solvent diffusion technique. The release rate of mefformin from the microcapsules was highly dependent on the encapsulating formulation, thus being used as an index for formulation screening. Orthogonal experiments were performed to optimize the coating formulation. Results The final chosen formulation for coating of mefformin microcapsules were as follows： （ 1 ） the ratio of EC （20cps） to EC （45cps） was 50：50; （2） the ratio of plasticizer to coating materials was 20% ;and （3） the ratio of resin-mefformin complexes to coating materials was 5 ： 1. Conclusion The prolonged release microspheres of mefformin hydrochloride were successfully prepared.

Kinetic modeling of adsorption of vanadium and iron from acid solution through ion exchange resins

This study assessed the adsorption process and the reaction kinetics involved in the selective recovery of vanadium from an acid solution containing iron as an impurity.Four commercial resins were studied:Lewatit^(®)MonoPlus TP 209 XL,Lewatit^(®) TP 207,Dowex^(TM)M4195(chelating resin)and Lewatit^(®) MonoPlus S 200 H(strong cationic exchange resin).To investigate the effect of time on the adsorption process,batch experiments were carried out using the following initial conditions:pH 2.0,298 K,and a proportion of 1 g of resin to 50 mL of solution.The variation of pH over time was analyzed.Chelating resin released less H+ions as the adsorption occurred,resulting in a lower drop of pH when compared to S 200 H resin.Ion adsorption by the resins was also evaluated through FT-IR and SEM−EDS before and after the experiments.Among the evaluated kinetic models(pseudo-first order,pseudo-second order,Elovich and intraparticle diffusion models),the pseudo-second order model best fits the experimental data of the adsorption of vanadium and iron by all of the four resins.M4195 resin showed the highest recovery of vanadium and the lowest adsorption of iron.Kinetic data,which are fundamental to industrial processes applications,are provided.

Synthesis and Adsorption Properties of Polystyrene-supported Chelating Resins Containing Heterocyclic Functional Groups

A series of new chelating resins with incorporating heterocyclic functional groups： pyridine, thiadizole, benzothizole into macroporous chloromethylated polystyrene were synthesized via hydrophilic spacer arm of polyethylene glycol containing sulfur. These chelating resins were found to show high adsorption capacities for Ag^＋, Hg^2＋, Au^3＋ and Pd^2＋, and the presence of spacer arm can enhance adsorption ability due to increase the hydrophilicity of the chelating resins.

Emission of BTEX and PAHs from molding sands with furan cold setting resins containing different contents of free furfuryl alcohol during production of cast iron

At present, furan resin is the largest selling no-bake system of moulding sands. The most commonly used furan no-bake binders(FNB) are condensation products of furfuryl alcohol(FA) urea, formaldehyde and phenol. They are generally cured by exposure to organic sulfonic acids. FNB provide excellent mold and core strength, cure rapidly and allow the sand to be reclaimed at fairly high yields, generally 75%-80%, especially in applications where due allowance is made for the need to keep total sulfur content below 0.1%. However, due to probable carcinogenic properties of furfuryl alcohol, the EU Directive limits the content of this substance(in a monomer form in resin) to 25%. The classification of furfuryl alcohol and the resulting furan resin products has changed from "harmful" to "toxic by inhalation". The aim of this study was to determine the effect of free furfuryl alcohol content in the resin on the emission of harmful substances from the BTEX(Benzene Toluene Ethylbenzene & Xylene) and PAHs(polycyclic aromatic hydrocarbon) group exposed to high temperature and how it affects the emissions allowance of reclaimed sand in the matrix. Three resins from a leading manufacturer were examined, which contain a free furfuryl alcohol content of 71%-72%, about 50% and < 25%, respectively. The hardener for each resin was 65% aqueous solution of paratoluenesulfonic acid. Tests were carried out in semi-industrial conditions where liquid cast-iron was poured into sample sand mold at 1,350 °C. The matrix of the studied sands was reclaimed in the amount of 0, 50%, 100%, respectively.With the increase of free furfuryl alcohol content, the volume of evolved gases decreased. For all resins the main component from the BTEX group dominating in the emitted gases was benzene; however toluene also appeared in the amount of a few percentages. In contrast, ethylbenzene and xylenes occurred only in the gases emitted from resin-bonded sands with the largest furfuryl alcohol content. The increase in the share of reclaimed sands resulted in very significant increase in the volume of gas generated and participation of benzene in these gases. In terms of emission of compounds from the PAHs group virtually for all resins, the total content of these substances was comparable(within the limits of error). The main components were: fluoranthene, pyrene and benzo(a) anthracene.

Effect of Hyperbranched Polyester on Modification of Epoxy Resins Cured with Anhydride

The synthesis and characterization of hyperbranched polyester （HBP） with different molecular weight are studied. The effect of HBP on the modification of epoxy resins cured with anhydride is mainly discussed. The characteristics of HBP and the morphologies of cured system are determined by nuclear magnetic resonance spectroscopy （NMR）, gel permeation chromatography （GPC） and scanning electron microscope （SEM）. The impact strength of cured system is detected and Fourier transform infrared （FTIR） measurements were used to pursue the curing process. The investigation shows that HBP can improve the toughness by forming copolymer networks between epoxy resins, HBP and anhydride. Moreover, when the molecular weight of HBP is 1342g/mol the toughening effect is the best, and the changes of toughness are small with the increase of molecular weight of HBP to 3500 g/mol.

Synthesis and Adsorption Properties of Chelating Resins Containing Sulfoxide and Heterocyclic Functional Groups

Several of new chelating resins containing sulfoxide and heterocyclic functional groups （3-aminopyridine and 2-mercaptobenzothiazole） based on macroporous chloromethylated polystyrene were synthesized and characterized by elemental analysis and infrared spectra. Their adsorption capacities towards Zn^2＋, Cu^2＋, Pb^2＋, Hg^2＋ and Ag^＋ at pH 3.0 and 6.0 were investigated in detail. It was found that the adsorption capacities of the resins containing bis[（3-pyridylaminoethyl）sulfoxide or （2-benzothiazolylthioethyl）sulfoxide for the above ions were higher than that on ones containing single above-mentioned groups.

Curing reaction and mechanism of phenol-formaldehyde novolac resins for foundry

In this study on the curing dynamics of phenol-formaldehyde novolac resins(PFNR) and hexamethylene tetramine(HMTA), two typical commercial PFNR were selected as examples and the curing reactions of the resins with HMTA were studied by differential scanning calorimetry(DSC). Based on the data calculated by the Kissinger equation and the Crane equation, a thermocuring dynamic model was established, from which the process conditions, activation energy, reaction kinetics equation and a f irst-order reaction of the curing reactions were derived.

Tannin–Phenol Formaldehyde Resins As Binders for Cellulosic Fibers: Mechanical Properties

In this study Eucalyptus tannin (T) was isolated from outer bark of Eucalyptus trees;as sodium phenoxide salt and used as extender or copolymer into phenol formaldehyde (PF) resin at five percent (10, 20, 30, 40 and 50)% W/W. Tan-nin-phenol formaldehyde (TPF) and tannin formaldehyde-phenol formaldehyde (TFPF) resins that synthesized in this study were evaluated as adhesive material for cellulosic fibers by study the mechanical properties of the composite sheets .The results show that the substituting of (PF) with tannin at (10 –50)% W/W give resins with mechanical properties comparable or near to those of pure (PF) , where the tensile strength at break (Tb) ranging from 15.15 Mpa to 22.27 Mpa as compared with 17.6 Mpa for pure (PF);while the impact strength properties (Im) of composites sheets increased with increased the (T) percents which were about 5.16 KJ/m2 for (TPF – 10%) and 7.21 KJ/m2 for (TPF - 50%) .On the other hand modification of (T) to tannin formaldehyde resin (TF) appear less performance at the results of this study , this effect probably to low penetration of (TFPF) resins between the small voids of cellulose fibers when soaked it in resin solutions. In general the results of this study indicate that the Eucalyptus tannin can be used for par-tial substitution of (PF) to produce resins with feasible mechanical properties and can be used in some applications of (PF) resins.

Ion Exchange Adsorption Kinetics of Miglitol by D001 Resins

In order to explore internal factors for adsorption kinetic effect of miglitol by D001 resin, a batch adsorption operation for miglitol kinetic adsorption at different concentrations, temperatures and vibrating rates was investigated in oscillator (SHZ-A), respectively. The different kinetic mathematical model, Webber-Morris kinetic equation, film diffusion coefficient equation and kinetic boundary model were all applied to discuss the adsorption process. The results showed that Type 1 pseudo-second order kinetic equation can be all used to describe miglitol adsorbed by D001 resin at different concentrations, temperatures and vibrating rates. Moreover, the total activation energy (Ea) can be calculated and its value is 9.7 kJ/mol, and then calculated values of the process film diffusion coefficient and pore diffusion coefficient, it may be inferred from these gotten values that the ion exchange process is all mainly controlled by film diffusion. Therefore, the results also suggest that the external adsorption factors such as solute concentration, temperature and vibrating rate for effect of mass transfer diffusion process control of miglitol onto D001 resin are relatively weak.

A Comparative Study of Bisphenol-A, Hydantoin and Cyanuric Acid Based Epoxy Resins Using XRD

To evaluate the efficiency of modified epoxy resins using bisphenol-A, hydantoin & cyanuric acid & to investigate the structural change due to the presence of Nitrogen atoms in polymeric chain for improved insulating properties, weatherability etc. The samples of epoxy resin bisphenol-a, hydantoin and Cyanuric acid based was taken for X-RAY diffraction analysis. The diffraction patterns were Fourier analysed to get an exact idea about the change in the polymer structure. From X-RAY diffraction analysis it was found that all physical parameters like area of cross section, number of carbon atoms per entanglement, stiffness parameter, particle size, percentage crystallinity & electron density fluctuation, in case of bisphenol-A based epoxy resin is more than other epoxy resins;that is;as the number of nitrogen atoms increased, all the physical parameters were reducedIn the present study only X-ray diffraction patterns of bisphenol-A, hydantoin and cyanuric acid based epoxy resins were studied. However their dielectric and ultrasonic properties could also be studied to get more information about the structur With the help of X-RAY diffraction patterns, one can easily check the synthesized samples of epoxy resins. The method to investigate the structural analysis of epoxy resin was novel and could find numerous applications in surfacecoatings.

Tannin Resins for Wood Preservatives:A Review

Tannins and wood preservatives,in this article,are briefly introduced at beginning.The research and application progress on tannin resins for wood preservatives at home and abroad are reviewed.The significance and development prospects of research on tannins for wood preservatives are prospected.

Rheological behavior of novel polyamide 6/silica nanocomposites containing epoxy resins

A novel polyamide 6/silica nanocomposite containing epoxy resins(EPA6N) was prepared via in situ polymerization using tetraethoxysilane(TEOS) as the precursor of silica.The dynamic rheological properties of pure PA6 and EPA6N at temperatures of 225 and 235 ℃ were investigated.The results of transmission electron microscopy(TEM) and atomic force microscopy(AFM) indicate that the silica particles are well dispersed in the polyamide 6 matrix on about 30 nm in diameter,which demonstrates that this method can effectively avoid agglomeration of the inorganic particles.The rheological results suggest that pure PA6 shows Newtonian behavior.However,the novel EPA6N exhibits a solid-like rheological behavior,which is due to the small size,large surface of silica particles and the stronger polyamide 6-silica chemical bond formed through the reactions of epoxy resins with end groups of PA6 molecular chains.The EPA6N also exhibits higher melt viscosity,storage modulus and loss modulus than those of pure PA6.