A New Method for Deriving High-Vertical-Resolution Wind Vector Data from the L-Band Radar Sounding System in China

High-vertical-resolution radiosonde wind data are highly valuable for describing the dynamics of the meso-and microscale atmosphere. However, the current algorithm used in China's L-band radar sounding system for calculating highvertical-resolution wind vectors excessively smooths the data, resulting in significant underestimation of the calculated kinetic energy of gravity waves compared to similar products from other countries, which greatly limits the effective utilization of the data. To address this issue, this study proposes a novel method to calculate high-vertical-resolution wind vectors that utilizes the elevation angle, azimuth angle, and slant range from L-band radar. In order to obtain wind data with a stable quality, a two-step automatic quality control procedure, including the RMSE-F(root-mean-square error F) test and elemental consistency test are first applied to the slant range data, to eliminate continuous erroneous data caused by unstable signals or radar malfunctions. Then, a wind calculation scheme based on a sliding second-order polynomial fitting is utilized to derive the high-vertical-resolution radiosonde wind vectors. The evaluation results demonstrate that the wind data obtained through the proposed method show a high level of consistency with the high-resolution wind data observed using the Vaisala Global Positioning System and the data observed by the new Beidou Navigation Sounding System. The calculation of the kinetic energy of gravity waves in the recalculated wind data also reaches a level comparable to the Vaisala observations.

Characterization of Aquifers in Crystalline and Crystallophyll Basement Zones Using the Electrical Resistivity Method (Trails and Electrical Soundings) in the Gagnoa Region, (Central-Western Côte d’Ivoire)

Introduction: Located in the central-western part of Côte d’Ivoire, the subsoil of the Gagnoa region is made up of sedimentary volcano formations and granitoids with developed fracturing. This complex Precambrian basement contains most of the region’s water resources. This is at the origin of the high failure rate during the various hydrogeological prospecting campaigns. Methodology: The database consists of resistivities from 42 holes and 51 trails drilled as part of the implementation of high-throughput drilling in the study area. The objective of this study is to deepen the knowledge of the fissured basement by interpreting profile curves and electrical soundings. It will be a question of classifying the different types of anomalies obtained on the profiles and their shapes. The orientation of the lineaments observed on the profiles was determined. Results: The interpretation of the geophysical data revealed various anomalies, the main ones being of the CC (Conductor Compartment) and CEDP (Contact between two bearings) types. These types of anomalies are mainly expressed in various forms: the “V”, “W” and “U” shapes. From these anomalies and the appearance of the electrical profiles, lineaments and their orientations were identified with N90-100, N130-140, N170-180 as major orientations. Conclusion: These results could contribute to a better understanding of the fractured environment of the Gagnoa region.

Analysis of Continuous Thunderstorm in One Week at Qingdao Airport Based on Sounding Data

Continuous thunderstorm occurring at Qingdao Airport in China from August 7 to 13,2022 was analyzed based on sounding data.The weather was divided into thunderstorm gale,thunderstorm and heavy precipitation,and some physical quantities and time variables which can effectively identify severe convective weather types were preliminarily obtained.The results show that CAPE was sensitive to different types of weather,but the uncertainty was relatively large.Convective temperature T_(CON),temperature difference between 500 and 850 hPa,and vertical wind shear can distinguish thunderstorm gale,thunderstorm and heavy precipitation weather obviously.Besides,K index,Showalter index,θ_(se) difference between 500 and 850 hPa were also important basis to distinguish thunderstorm and heavy precipitation weather.Thunderstorm gale can be distinguished by the 24-hour variations of K index,and the difference of dew point between 500 and 850 hPa.The 24-hour variations of(T-T_(d))_(500) and vertical wind shear can be used to distinguish between heavy precipitation and thunderstorm weather;the 24-hour variation of stratification stability Δθ_(se) can distinguish the three kinds of weather well.For the wind field,the existence of vertical wind shear was required for strong convective weather,and the 24-hour increment of thunderstorm gale and thunderstorm was larger than that of heavy precipitation.

Groundwater Potential Mapping in Lapan Gwari Community Using Integrated Remote Sensing and Electrical Resistivity Soundings

This research aims to address the pressing issue of failed and abandoned wells, causing water scarcity in Lapan Gwari Community, through an improved groundwater exploration approach integrating remote sensing and electrical resistivity soundings. The study area, located within the Zungeru Sheet 163 SE, spans Latitudes 9°30'00"N to 9°32'00"N and Longitudes 6°28'00" to 6°30'00". The surface geologic, structural, and hydrogeological mapping provided essential insights into the hydrogeological framework. Leveraging SRTM DEM data, thematic maps were created for geomorphology, slope, land use, lineament density, and drainage density. These datasets were then integrated using ArcGIS to develop a preliminary groundwater potential zones map. Further investigations were conducted using Vertical Electrical Sounding (VES) and Electrical Resistivity Imaging (2D VES) surveys at targeted locations identified by the preliminary map. Results show that the study area predominantly consists of crystalline rocks of the Nigerian Basement Complex, primarily comprising schist and granite with minor occurrences of quartz vein intrusions. Surface joint directions indicated a dominant NE-SW trend. The VES data revealed three to four geoelectric layers, encompassing the topsoil (1 to 5 m depth, resistivity: 100 Ωm to 300 Ωm), the weathered layer (in the 3-layer system) or fractured layer (in the 4-layer system), and the fresh basement rock characterized by infinite resistivity. The shallow weathered layers (3 to 30 m thickness) are believed to hold aquiferous potential. Hydrogeological interpretation, facilitated by 2D resistivity models, delineated water horizons trapped within clayey sand and weathered/fractured formations. Notably, the aquifer resistivity range was found to be between 3 - 35 m and 100 - 300 Ωm, signifying a promising aquifer positioned at depths of 40 to 88 m. This aligns with corroborative static water level measurements. Given this, we recommend drilling depths of a minimum of 80 m to ensure the acquisition of sufficient and sustainable water supplies. The final groundwater potential zones map derived from this study is expected to serve as an invaluable guide for prospective groundwater developers and relevant authorities in formulating effective water resource management plans. By effectively tackling water scarcity challenges in Lapan Gwari Community, this integrated approach demonstrates its potential for application in similar regions facing comparable hydrogeological concerns.

Comparison and Analysis between Two Types of Sounding Data of China

The upper air weather forecast data used in current business and research and digital data of the recently finished upper air meteorological monthly report were comparatively analyzed in complete data and quality condition of data, and sounding curve change caused by the difference of complete data was also compared, which evaluated advantages and disadvantages of two types of data.

Development of multi-channel observation and inversion for IP electrical sounding method

In order to improve the exploration effect of deep non-ferrous mineral resources, multi-channel observation methods for induced polarization （IP） electrical sounding data and their inversion imaging technology are studied. First of all, four multi-channel observation methods are developed based on conventional IP electrical method, namely three-electrode and four-electrode arrays of unilateral and bilateral current transmitting. Then the maximum smoothness constrained inversion method of the least squares sense for IP electrical sounding data is proposed, and the inversion software is programmed. Finally, the simulation and inversion results of geo-electrical model for the proposed observation methods are analyzed. And the comparison results show that three-electrode array of bilateral current transmitting gives the best result, but the intensity in field work is larger than others; unilateral three-electrode and four-electrode arrays give the better results. Taking detection results and convenience of field exploration work into consideration, these two methods are more suitable for practical application; bilateral observation method of four-electrode array is not suitable for the detection of the steep ore bodies.

Analysis of Atmospheric Boundary Layer Height Characteristics over the Arctic Ocean Using the Aircraft and GPS Soundings

Utilizing aircraft sounding data collected from the Surface Heat Budget of the Arctic Ocean (SHEBA, 1998) campaign, the authors evaluated commonly-used profile methods for Arctic ABL height estimation by validating against the'true'ABL height from aircraft sounding profiles, where ABL height is defined as the top of the layer with significant turbulence. Furthermore, the best performing method was used to estimate ABL height from the one-year GPS soundings obtained during SHEBA (October 1997-October 1998). It was found that the temperature gradient method produces a reliable estimate of ABL height. Additionally, the authors determined optimal threshold values of temperature gradient for stable boundary layer (SBL) and convective boundary layer (CBL) to be 6.5 K/100 m and 1.0 K/100 m, respectively. The maximum ABL height during the year was 1150 m occurred in May. Median values of Arctic ABL height in May, June, July, and August were 400 m, 430 m, 180 m, and 320 m, respectively. Arctic ABL heights are clearly higher in the spring than in the summer.

Crustal Structure Revealed by a Deep Seismic Sounding Profile of Baijing-Gaoming-Jinwan in the Pearl River Delta

The Pearl River Estuary area, located in the middle part of the southern China coastal seismic belt, has long been considered a potential source of strong earthquakes above magnitude 7.0. To scientifically assess the potential strong earthquake risk in this area, a three-dimensional artificial seismic sounding experiment, consisting of a receiving array and seabed seismograph, was performed to reveal the deep crustal structure in this region. We used artificial ship-borne air-gun excitation shots as sources, and fixed and mobile stations as receivers to record seismic data from May to August 2015. This paper presents results along a line from the western side of the Pearl River Estuary to the western side of the Baijing-Gaoming-Jinwan profile. A two-dimensional velocity structure was constructed using seismic travel-time tomography. The inversion results show that the Moho depth is 27 km in the coastal area and 30 km in the northwest of the Pearl River Estuary area, indicating that the crust thins from land to sea. Two structural discontinuities and multiple low-velocity anomalies appear in the crustal section. Inside both discontinuity zones, a low-velocity layer, with a minimum velocity of 6.05 km s^(-1), exists at a depth of about 15 km, and another, with a minimum velocity of 6.37 km s^(-1), exists at a depth of about 21.5 km between the middle and lower crust. These low velocities suggest that the discontinuities may consist of partly molten material. Earthquakes with magnitudes higher than 5.0 occurred in the low-velocity layer along the profile. The deep Kaiping-Enping fault, rooted in the crust, may be one of the most important channels for deep material upwelling and is related to tectonic movement since the Cretaceous in the Pearl River Delta tectonic rift basin.

A New Infrared Atmospheric Sounding Interferometer Channel Selection and Assessment of Its Impact on Met Office NWP Forecasts

A new set of Infrared Atmospheric Sounding Interferometer （IASI） channels was re-selected from 314 EUMETSAT channels. In selecting channels, we calculated the impact of the individually added channel on the improvement in the analysis outputs from a one-dimensional variational analysis （1D-Var） for the Unified Model （UM） data assimilation system at the Met Office, using the channel score index （CSI） as a figure of merit. Then, 200 channels were selected in order by counting each individual channel＇s CSI contribution. Compared with the operationally used 183 channels for the UM at the Met Office, the new set shares 149 channels, while the other 51 channels are new. Also examined is the selection from the entropy reduction method with the same 1D-Var approach, Results suggest that channel selection can be made in a more objective fashion using the proposed CSI method. This is because the most important channels can be selected across the whole IASI observation spectrum. In the experimental trial runs using the UM global assimilation system, the new channels had an overall neutral impact in terms of improvement in forecasts, as compared with results from the operational channels. However, upper-tropospheric moist biases shown in the control run with operational channels were significantly reduced in the experimental trial with the newly selected channels. The reduction of moist biases was mainly due to the additional water vapor channels, which are sensitive to the upper-tropospheric water vapor.

Bathymetry predicted from vertical gravity gradient anomalies and ship soundings

In this paper, the admittance function between seafloor undulations and vertical gravity gradient anomalies was derived. Based on this admittance function, the bathymetry model of 1 minute resolution was predicted from vertical gravity gradient anomalies and ship soundings in the experimental area from the northwest Pacific. The accuracy of the model is evaluated using ship soundings and existing models, including ETOPO1, GEBCO, DTU10 and V15.1 from SIO. The model＇s STD is 69. 481m, comparable with V15.1 which is generally believed to have the highest accuracy.

Use of Total Precipitable Water Classification of A Priori Error and Quality Control in Atmospheric Temperature and Water Vapor Sounding Retrieval

This study investigates the use of dynamic a priori error information according to atmospheric moistness and the use of quality controls in temperature and water vapor profile retrievals from hyperspectral infrared （IR） sounders. Temperature and water vapor profiles are retrieved from Atmospheric InfraRed Sounder （AIRS） radiance measurements by applying a physical iterative method using regression retrieval as the first guess. Based on the dependency of first-guess errors on the degree of atmospheric moistness, the a priori first-guess errors classified by total precipitable water （TPW） are applied in the AIRS physical retrieval procedure. Compared to the retrieval results from a fixed a priori error, boundary layer moisture retrievals appear to be improved via TPW classification of a priori first-guess errors. Six quality control （QC） tests, which check non-converged or bad retrievals, large residuals, high terrain and desert areas, and large temperature and moisture deviations from the first guess regression retrieval, are also applied in the AIRS physical retrievals. Significantly large errors are found for the retrievals rejected by these six QCs, and the retrieval errors are substantially reduced via QC over land, which suggest the usefulness and high impact of the QCs, especially over land. In conclusion, the use of dynamic a priori error information according to atmospheric moistness, and the use of appropriate QCs dealing with the geographical information and the deviation from the first-guess as well as the conventional inverse performance are suggested to improve temperature and moisture retrievals and their applications.

Deep seismic sounding investigation into the deep structure of the magma system in Changbaishan-Tianchi volcanic region

The magma system of Changbaishan-Tianchi Volcanic region is studied with three-dimensional deep seismic sounding (DSS) technique. The results show that the magma system of Changbaishan-Tianchi volcanic region, mainly characterized by low velocity of P wave, can be divided into three parts in terms of depth. At the depth range of 9-15 km, the distribution of the magma system is characterized by extensiveness, large scale and near-SN orientation. This layer is the major place for magma storage. From the depth of 15 km down to the lower crust, it is characterized by small lateral scale, which indicates the 'trace' of magma intrusion from the upper mantle into the crust and also implies that the magma system most probably extends to the upper mantle, or even deeper.(less than 8-9 km deep), the range of magma distribution is even smaller, centering on an SN-oriented area just north of the Tianchi crater. If low velocity of P wave is related to the magma system, it then reflects that the magma here is still in a state of relatively high temperature. In this sense, the magma system of Changbaishan-Tianchi volcanic region is at least not 'remains', in other words, it is in an 'active' state.

The application of the high-frequency electromagnetic sounding method in the exploration of underground thermal water

High-frequency electromagnetic sounding is an electromagnetic exploration method using the natural high-frequency electromagnetic field as a field source. It has higher resolution and greater depth penetration than the direct current method and is especially fit for geothermal energy exploration and low- and mid-level groundwater detection. We introduce a successful application of high-frequency electromagnetic sounding for evaluating geothermal water resources. The high frequency electromagnetic system （MT-USA with a frequency range from 10 KHz to 1 Hz） is first applied to sample field data from China. A remote reference station is used to assure sampled data quality. We then perform 2D inversion image processing with the electrical method data. The results basically indicate the spatial distribution of underground geothermal water and provide favorable clues to finding the sources of the subsurface geothermal water in this area.

Three-dimensional forward modeling for magnetotelluric sounding by finite element method

A finite element algorithm combined with divergence condition was presented for computing three-dimensional(3D) magnetotelluric forward modeling. The finite element equation of three-dimensional magnetotelluric forward modeling was derived from Maxwell's equations using general variation principle. The divergence condition was added forcedly to the electric field boundary value problem, which made the solution correct. The system of equation of the finite element algorithm was a large sparse, banded, symmetric, ill-conditioned, non-Hermitian complex matrix equation, which can be solved using the Bi-CGSTAB method. In order to prove correctness of the three-dimensional magnetotelluric forward algorithm, the computed results and analytic results of one-dimensional geo-electrical model were compared. In addition, the three-dimensional magnetotelluric forward algorithm is given a further evaluation by computing COMMEMI model. The forward modeling results show that the algorithm is very efficient, and it has a lot of advantages, such as the high precision, the canonical process of solving problem, meeting the internal boundary condition automatically and adapting to all kinds of distribution of multi-substances.

A Fast Algorithm of Cartographic Sounding Selection

An effective strategy and framework that adequately integrate the automated and manual processes for fast cartographic sounding selection is presented. The important submarine topographic features are extracted for important soundings selection, and an improved "influence circle" algorithm is introduced for sounding selection. For automatic configuration of soundings distribution pattern, a special algorithm considering multi factors is employed. A semi automatic method for solving the ambiguous conflicts is described. On the basis of the algorithms and strategies a system named HGIS for fast cartographic sounding selection is developed and applied in Chinese Marine Safety Administration Bureau (CMSAB). The application experiments show that the system is effective and reliable. At last some conclusions and the future work are given.

AN ALGORITHM FOR AUTOMATIC CARTOGRAPHIC SOUNDING SELECTION

Soundings on nautical charts provide information about the shape of ocean bottom between chart depth curves. A single chart may have thousands of soundings posted on it. This paper describes a new algorithm for selecting soundings automatically. At first,the problem encountered in automatic cartographic sounding selection is presented. Then the authors give the principle of the new algorithm,and the implementation is illuminated in detail. At last the experiments prove the rationality and efficiency of the new algorithm.

Study on the detection of abnormal sounding data based on LS-SVM

A new method of detecting abnormal sounding data based on LS-SVM is presented.The theorem proves that the trend surface filter is the especial result of LS-SVM.In order to depict the relationship of trend surface filter and LS-SVM,a contrast is given.The example shows that abnormal sounding data could be detected effectively by LS-SVM when the training samples and kernel function are reasonable.

Optimal placement of two soil soundings for rectangular footings

This study uses a recently proposed algorithm for consideration of soil sounding locations in the bearing capacity estimations of spatially variable soil for rectangular footings.The objective of the study is to assess the possibility of indicating general guidelines for optimal soil sounding locations in the case of two soundings and rectangular footings.The possibility of proposing such general guidelines would be extremely valuable from the engineering practice point of view.Moreover,it would be promising for future studies concerning more complex foundation arrangements.For this reason,numerous scenarios are analyzed for a variety of vertical and horizontal fluctuation scales and a variety of rectangular foundation lengths.For generality of the results,two correlation structures are considered,i.e.the Gaussian and the Markovian ones.The optimal sounding location results are discussed.The observations indicate that,for a specified vertical fluctuation scale,all optimal borehole locations in dimensionless coordinates form a curve.This phenomenon can be utilized in practical applications.The potential applications of the obtained results and the directions for future studies in this area are also discussed.

Crustal Structure of the Chuan-Dian Block Revealed by Deep Seismic Sounding and its Implications for the Outward Expansion of the East Tibetan Plateau

The Chuan-Dian Block(CDB)is located in the southeastern margin of the Tibetan Plateau,with a complex geological structure and active regional faults.The present tectonic condition with strong crustal deformation is closely related to the ongoing collision of the India and Eurasia plates since 65 Ma.The study of the crustal structure of this area is key to revealing the evolution and deep geodynamics of the lateral collision zone of the Tibetan Plateau.Deep seismic sounding is the most efficient method with which to unravel the velocity structure of the whole crust.Since the 1980s,19 deep seismic sounding profiles have been captured within the CDB area.In this study,we systematically integrate the research results of the 19 profiles in this area,then image the 3D crustal velocity,by sampling with a 5 km spacing and 2D/3D Kriging interpolation.The results show the following.(1)The Moho depth in the study area deepens from 30 km in the south to 66 km in the north,whereas there is no apparent variation from west to east.The Pn wave velocity is higher in stable tectonic units,such as 7.95 km/s in the Lanping-Simao block and 7.94 km/s in the western margin of the Yangtze block,than in active or mobile tectonic units,such as 7.81 km/s in the Baoshan block,7.72 km/s in the Tengchong block and 7.82 km/s in the Zhongdian block.(2)The crustal nature of the Tengchong block,the northern Lanping-Simao block and the Zhongdian block reflects a type of orogenic belt,having relatively strong tectonic activities,whereas the crustal nature of the central Lanping-Simao block and the western margin of the Yangtze block represents a type of platform.The different features of the upper-middle crust velocity,Moho depth and Pn wave velocity to both sides of the Red River fault zone and the Xianshuihe fault zone,reflect that they are clearly ultra-crustal.(3)Based on the distribution of the low velocity zones in the crust,the crustal material of the Tibetan Plateau is flowing in a NW–SE direction to the north of 26°N and to the west of 101°E,then diverting to flowing eastwards to the east of 101°E.

A Step Forward toward Effectively Using Hyperspectral IR Sounding Information in NWP

Satellite-based atmospheric sounding measurements with high spectral resolution or from hyperspectral infrared （IR） sounders are important global observations for improving weather forecasts through assimilating them into operational numerical weather prediction （NWP） systems.