Preparation and Thermal Shock Resistance of Mullite Ceramics for High Temperature Solar Thermal Storage

Mullite thermal storage ceramics were prepared by low-cost calcined bauxite and kaolin.The phase composition,microstructure,high temperature resistance and thermophysical properties were characterized by modern testing techniques.The experimental results indicate that sample A3(bauxite/kaolin ratio of 5:5)sintered at 1620℃has the optimum comprehensive properties,with bulk density of 2.83 g·cm^(-3)and bending strength of 155.44 MPa.After 30 thermal shocks(1000℃-room temperature,air cooling),the bending strength of sample A3 increases to 166.15 MPa with an enhancement rate of 6.89%,the corresponding thermal conductivity and specific heat capacity are 3.54 W·(m·K)^(-1)and 1.39 kJ·(kg·K)^(-1)at 800℃,and the thermal storage density is 1096 kJ·kg^(-1)(25-800 mullite ceramics;sintering properties;high-temperature thermal storage;thermal shock resistance).Mullite forms a dense and continuous interlaced network microstructure,which endows the samples high thermal storage density and high bending strength,but the decrease of bauxite/kaolin ratio leads to the decrease of mullite content,which reduces the properties of the samples.

Preparation of micro-arc oxidation coatings on magnesium alloy and its thermal shock resistance property

In the NaAlO2-Na2SiO3 compound system, the ceramic coatings were prepared on magnesium alloy by micro-arc oxidation. The morphology, phase composition, and thermal shock resistance of the ceramic coatings were studied by scanning electron microscope, X-ray diffraction and thermal shock tests, respectively. The results showed that the ceramic coating contains MgO, MgAl2O4, as well as a little amount of MgESiO4. The thickness of the ceramic coatings increases with the current density increasing, when the current density is 12 A·dm^-2, the thermal shock resistance of the produced ceramic coating is the best. The hardness of the ceramic coating is up to 10 GPa or so.

Effect of Rare Earth on Thermal Shock Resistance of Steel 9Cr2Mo

The effect of rare earth elements on thermal shock resistance of cold roller steel 9Cr2Mo was investigated by means of X-ray diffractometry and optical microscopy. Experimental results show that the process of carbide precipitation of heat effect zone is restrained by adding RE elements in steel 9Cr2Mo. Therefore, thermal shock resistance of this steel can be improved.

Thermal Shock Resistance of Nano SiC-BN Composites

Nano SiC - BN composite powders were prepared by dissolving analytically pure H3BO3 and CO（ NH2 ）2 with the mole ratio of 1：2.5 in the absolute alcohol, adding 80% E-SiC with 0. 2 μm average grain size while stirring, firing at 850 ℃ in nitrogen （purity： 99. 99%, pressure： O. 92 -0. 93 MPa） for 15 h. Nano SiC -BN composite specimens were prepared by hot-pressed sintering the nano SiC - BN composite powder in N2 atmosphere with 0. 92 - 0. 93 MPa and at 30 MPa axial pressure for 0. 5 - 1 h at 1 750 - 1 800 ℃. The thermal shock resistance of nano SiC -BN composites was studied by three-point bending, TEM and SEM. The results show that, adding BN can decrease the modulus of elasticity of SiC materials, which improves thermal shock resistance;furthermore, because of the large difference of thermal expansion coefficient between matrix SiC and second phase hexa-BN, thermal mismatch effect results in intercrystalline delamination of h-BN grains and forming many micropores in composite ceramic, which can relax the thermal expansion caused by high tempera- ture effectively, and improve the thermal shock resistance significantly.

Effect of CaO doping on mechanical properties and thermal shock resistance of 10NiO-NiFe_2O_4 composite ceramics

The CaO doped 10NiO-NiFe2O4 composite ceramics were prepared by the cold isostatic pressing-sintering process, and the effects of CaO content on the phase composition, mechanical property and thermal shock resistance of 10NiO-NiFe2O4 composite ceramics were studied. The results show that the samples mainly consist of NiO and NiFe2O4 when content of CaO is less than 4%(mass fraction), bending strength increases obviously by CaO doping. Bending strength of the samples doped with 2% CaO is above 185 MPa, but that of the samples without CaO is only 60 MPa. Fracture toughness is improved obviously by CaO doping, the samples doped with 2% CaO have the maximum fracture toughness of 2.12 MPa ·m1/2 , which is about two times of that of the undoped ceramics. CaO doping is bad to thermal shock resistance of 10NiO-NiFe2O4 composite ceramics.

Relation Between Sintering Reactivity of Matrix and Thermal Shock Resistance of Ultra-low Cement Bonded Corundum-spinel Castables for Fired Purging Plugs

Purging plugs installed in the bottom of steel ladles are widely used for the secondary refining of high quality steel grades.The dynamic service conditions and temperature gradients caused by the cold inert gas blown through the plug during stirring create a strong thermal shock impact on the materials.This can affect its service life and restrict the safety and efficiency of steel making if the plug fails during use.In this work,the influence of the particle size distribution (PSD) and amount of reactive alumina on the sintering behavior of ultra-low cement bonded corundum-spinel based castables was investigated on lab scale.The relationship between sintering reactivity of matrix and thermal shock resistance of castables was evaluated in detail.Results show that the sintering of castables can be intensified by using finer reactive alumina.However,excessive sintering of the castable through finer reactive alumina is negative for thermal shock resistance.The microstructure characterization reveals that castables with more intense sintering show denser matrix structure,which is less effective in hampering crack propagation and therefore results in decline of their thermal shock resistance.

Effect of Fused MgO-ZrO_2 Clinker Addition on Thermal Shock Resistance of MgO-ZrO_2 Unfired Bricks

MgO -ZrO2 unfired bricks with ZrO2 content up to 8% at the interval of 2% were prepared, using fused magnesia （ MgO ： 97% ） and fused MgO - ZrO2 clinker （ ZrO2 ： 14. 33% ） as starting materials and phenolic resin as binder. The effects of ZrO2 content on thermal shock resistance （TSR） and other properties such as cold and hot modulus of rupture have been investigated. Re- sidual cold modulus of rupture ratio after heating at 1 000 ℃ and quenching by air blowing was adopted to characterize TSR. Addition of the MgO -ZrO2 clinker improves TSR, attributing to the microcrack toughening effect by thermal expansion mismatch between different phases. When ZrO2 content goes above 4%. the impro- ving effect tends to be moderate. The introduction of MgO- ZrO2 clinker can also improve the HMOR at 1 500 ℃, while the increased ZrO2 content reduces CMOR of the bricks prefired at 1 600 ℃, due to the thermal expansion mismatch effect. Compromising the overall properties, the optimal ZrO2 content for such magnesia based unfired brick is suggested to be 4%.

Thermal Shock Resistances of FeMnCr/Cr_3C_2 Coatings Deposited by Arc Spraying

Arc spraying with the cored wires was applied to deposit FeMnCr/Cr3C2 coatings on low carbon steel substrates, namely FM1, FM2 and FM3. Thermal shock resistances of the coatings were investigated to assess the influence of Cr3C2 content on thermal shock resistance. Characteristics of the coatings under thermal cycling test were studied by optical microscopy, field emission scanning electron microscope （FE-SEM） and energy dispersion spectrum （EDS）, X-ray diffraction （XRD）. The experimental results show that hardness of the coatings increases, bonding strength decreases slightly with increase of the Cr3C2 content of the coatings. As a result, FM2 coating possesses the best thermal shock resistance, attributing to its better thermal expansion matches and wettability than those of FM3 coating, less oxide rate than that of FM1 coating restraining from cracks formation and propagation in coatings.

Effects of mechanical boundary conditions on thermal shock resistance of ultra-high temperature ceramics

The effects of mechanical boundary conditions, often encountered in thermalstructural engineering, on the thermal shock resistance（TSR） of ultra-high temperature ceramics（UHTCs） are studied by investigating the TSR of a UHTC plate with various types of constraints under the first, second, and third type of thermal boundary conditions. The TSR of UHTCs is strongly dependent on the heat transfer modes and severity of the thermal environments. Constraining the displacement of the lower surface in the thickness direction can significantly decrease the TSR of the UHTC plate, which is subject to the thermal shock at the upper surface. In contrast, the TSR of the UHTC plate with simply supported edges or clamped edges around the lower surface is much better.

Properties and appropriate conditions of stress reduction factor and thermal shock resistance parameters for ceramics

Through introducing the analytical problem of the plate with convection into the solution of the transient heat conduction thermal stress field model of the elastic plate, the stress reduction factor is presented explicitly in its dimensionless form. A new stress reduction factor is introduced for the purpose of comparison. The proper- ties and appropriate conditions of the stress reduction factor, the first and second ther- mal shock resistance （TSR） parameters for the high and low Biot numbers, respectively, and the approximation formulas for the intermediate Blot number-interval are discussed. To investigate the TSR of ceramics more accurately, it is recommended to combine the heat transfer theory with the theory of thermoelasticity or fracture mechanics or use a numerical method. The critical rupture temperature difference and the critical rup- ture dimensionless time can be used to characterize the TSR of ceramics intuitively and legibly.

Fabrication and plasma arc thermal shock resistance of HfB_2-based ultra high temperature ceramics

Two hafnium diboride based ceramic matrix composites containing 20% （volume fraction） SiC particle and with or without AIN as sintering additives were fabri,aated by hot-pressed sintering. The mechanical properties and microstructures of these two composites were tested and the thermal shock resistances were evaluated by plasma arc heater. The results indicate that the composite with A1N as sintering additive has a denser and finer microstructure than composite without sintering additive, and the mechanical properties, thermal shock resistance of the composite with A1N as sintering additive are also higher than those of the composite without A1N. Microstructure analysis on the cross-section of two composites after thermal shock tests indicates that a compact oxidation scale contains HfO2 and Al2O3 liquid phase is found on the surface of composite with A1N, which could fill the voids and cracks of surface and improve the thermal shock resistance of composite.

Thermal Shock Resistance of Bauxite-based β-Sialon Bonded Corundum Materials

Thermal shock resistant properties of reaction sintered bauxite-based β-Sialon bonded corundum have been investigated, and the results are compared with those of Al_ 2O_ 3 based counterpart. It is found they all have very good thermal shock resistance. Their residual strength ratios after one thermal shock cycle at ΔT=1200℃ and ΔT=1350℃ are 61%~73% and 53%~65% respectively. Their critical temperature difference (TSR) is 600℃~800℃. TSR parameters are calculated based on thermal expansion, modulus of elasticity, and fracture toughness determined. The reasons for improving TSR of these composite materials are discussed.

Design of Composite Ladle Shroud for Improving Thermal Shock Resistance

A ladle shroud is one of the functional refractories for continuous casting,which undergoes severe thermal shock by molten steel when used without pre-heating.The composite ladle shroud with an insulating liner presents excellent thermal shock resistance.Finite element simulation is an effective method to explore the maximum thermal stress for predicting the thermal shock resistance of ladle shrouds.In this paper,the influence of the lining materials and the structure of ladle shrouds on the thermal stress distribution is systematically researched.The working mechanism of the lining material on the body material is also presented.Lining materials with low thermal expansion,elastic modulus and thermal conductivity are helpful to improve the thermal shock resistance and an optimum lining thickness is suggested.The lining material can both serve as thermal resistance for the body material to buffer the thermal stress,and apply a strain load to the body material by the thermal strain to increase the stress.

Effects of Additive CeO_2 on Thermal Shock Resistance of Plasma-Sprayed Cr_2O_3 Coating

The influence of CeO2 with different content on the thermal shock resistance of plasmasprayed Cr2O3 coating was investigated. The thermal shock failure mechanism of coating was also studied. It is found that the thermal shock failure mechanism of coating is thermal stress fatigue destruction, and the destruction takes place at interface of ceramic and bond coating. The experimental results show that the lifetime of coating fracture and failure increase considerably when 3% CeO2 is added into the plasma-sprayed Cr2O3 coating. The suitable content of CeO2 makes the microcracks exist in network form. The microcrack net can release internal stress in coating, delay the crack forming and expanding and decrease holes in coating. Thus the thermal shock resistance increase largely.

Thermal Shock Resistance and Erosion Resistance of TiB_2 Multiphase Ceramic Composites

The thermal shock resistance and anti- aluminum erosion of TiB2 - BN multiphase ceramics composites were studied. The experimental results show that the TiB2-BN multiphase ceramic possesses a good thermal shock resistance at high temperatures （ 1000, 1200, 1400, 1500 ℃ ）, with the increasing in thermal shocking temperature, the electro-conductivity of TiB2-BN ceramics increases. The metal aluminum has a great influence on the properties of TiB2 - BN ceramics and the main reason is that the aluminum reacts seriously with BN. It is suggested that the content of BN should be reduced to the greatest extent.

Preparation of yttrium oxide coating with enhanced thermal shock resistance on refractories used for titanium alloy melting and casting

In order to enhance the service life of refractories for melting and casting of titanium alloy,preparation of yttrium oxide coatings on the refractories surface is an effective solution.The improvement of thermal shock stability of the coating is beneficial to its spalling resistance during the high-temperature service,and the available slurry with good performance is the prerequisite.The effects of the varieties and contents of dispersant(sodium tripolyphosphate,sodium hexametaphosphate,sodium pyrophosphate,citric acid and polycarboxylate ammonium salt)and binder(aluminum dihydrogen phosphate,zirconium acetate and yttria sol)on the stability,rheological and thixotropic properties of yttrium oxide waterbased slurry were investigated,and the effects of slurry composition design on the thermal shock resistance of the coating were focused.The results showed that the introduction of polycarboxylate ammonium salt as dispersant significantly improved the stability of the slurry,and the varieties of the binders had significant effects on the dispersibility of the slurry.When aluminum dihydrogen phosphate and polycarboxylate ammonium salt were used as binder and dispersant,respectively,the slurry had better stability,suitable rheological and thixotropic properties.By using aluminum dihydrogen phosphate as binder,the coating had good thermal shock resistance and no obvious cracks were observed for the coating after thermal shock,which was attributed to the yttrium aluminate binding phase generated in the coating.An effective method was provided for preparing yttrium oxide coatings with enhanced thermal shock resistance applied in the process of titanium alloy melting and casting.

A novel route to enhance high-temperature mechanical property and thermal shock resistance of low-carbon Mgo-C bricks by introducing ZrSiO_(4)

Conventional MgO-C bricks(graphite content>14 wt.%)produce a great deal of greenhouse gas emission,while low-carbon MgO-C bricks have serious thermal shock resistance during high-temperature service.To enhance the high-temperature mechanical property and thermal shock resistance of low-carbon MgO-C bricks,a novel route of introducing ZrSiO_(4) powder into low-carbon MgO-C bricks was reported in such refractories with 2 wt.% flaky graphite.The results indicate that the low-carbon MgO-C brick with 0.5 wt.%ZrSiO_(4) addition has the maximum hot modulus of rupture at 1400℃ and the corresponding specimen fired in the carbon embedded atmosphere has the maximum residual strength ratio(98.6%)after three thermal shock cycles.It is found that some needle-like AlON and plate-like Al_(2)O_(3)-ZrO_(2) composites were in situ formed in the matrices after the low-carbon MgO-C bricks were coked at 1400℃,which can enhance the high-temperature mechanical property and thermal shock resistance due to the effect of fiber toughening and particle toughening.Moreover,CO_(2) emission of the newly developed low-carbon MgO-C bricks is reduced by 58.3% per ton steel after using them as the working lining of a 90 t vacuum oxygen decarburization ladle.

Efficient fabrication of light Cf/SiHfBOC composites with excellent thermal shock resistance and ultra-high-temperature ablation up to 1800℃

In this paper,a high-yield Hf-modified SiHfBOC ceramic precursor was developed,and a high-pressure assisted impregnation pyrolysis method was proposed to achieve the preparation of 3D PyC–Cf/SiHfBOC composites.This high-pressure assisted impregnation method significantly improves impregnation filling effect of the precursor in and between fiber bundles compared to dozens of traditional impregnation cycles.After undergoing just 9 precursor infiltration pyrolysis(PIP)cycles,the composites achieved relative density of approximately 90%and density of 1.64 g/cm^(3).The critical temperature difference of the 3D PyC–Cf/SiHfBOC composites after the shock of room temperature(RT)–1000℃is as high as 650℃,which is twice that of traditional ceramic materials,showing good thermal shock resistance.Under the effect of Hf modification,a dense HfO_(2)–SiO_(2)oxide layer(thickness of 93μm)was formed in situ on the surface of the 3D PyC–Cf/SiHfBOC composites,effectively preventing further erosion of the composite matrix by high-temperature oxidation gas.Even in the ultra-high-temperature oxygen-containing environment at 1800℃,it still exhibits an excellent non-ablative result(with a linear ablation rate of 0.83×10^(−4)mm/s).This work not only enriches the basic research on lightweight ultra-high-temperature ceramic composites converted from Hf ceramic precursors,but also provides strong technical support for their applications in ultra-high-temperature non-ablative thermal protection materials for high-speed aircraft.

Excellent thermal shock resistance of NiCrAlY coatings on copper substrate via laser cladding

Coatings are widely used to protect substrates in extreme thermal environments(e.g., arc heaters), and thermal shock resistance is a crucial parameter for the coatings, which requires tight interlayer bonding between coatings and substrates. In this work, Ni Cr Al Y coatings were highly required for the pure copper substrate to restrict the electric arc in arc heaters. To overcome the bonding difculty of coating on the copper surface, the Ni Cr Al Y coatings were prepared by two laser cladding methods: conventional laser cladding(CLC) and high-speed laser cladding(HSLC). The microstructure, composition, and thermal shock resistance of Ni Cr Al Y cladding layers prepared by both methods were investigated. Benefitting from the high cooling rate and high energy density, the HSLC-layer has better composition uniformity and tighter interlayer bonding than the CLC-layer, achieving a 30%–45% improvement in thermal cycling lifetime. Besides, the Ni Cr Al Y layers prepared on copper substrate by both laser cladding methods exhibit3–10 times better thermal shock resistance than those Ni Cr Al Y layers prepared by conventional spraying methods. It further confirms the great effects of metallurgical bonding and composition uniformity on the thermal shock resistance of coatings. The Ni Cr Al Y layers fail in the form of internal cracking and interface peeling, and the corresponding failure mechanism is discussed.

Normalized evaluation of thermal shock resistance for ceramic materials

A normalized method for evaluation of thermal shock resistance for ceramic materials was proposed.A thermal shock resistance index(TSRI),Г,in the range of 1 to 100,was introduced,based on a normalized formula obtained directly by a simple testing process of determining the changes in flexural strength before and after thermal shock cycles.Alumina ceramic was chosen as the model material and its thermal shock behavior was investigated systematically by water quenching.Based on the experiments on alumina ceramic,the thermal shock behaviors of other 19 types of ceramic materials ranging from porcelain,refractory ceramics to advanced ceramics including structural and functional ceramics were also evaluated,and their TSRIs,Г,were derived.The dependence ofГon the coefficient of thermal expansion(CTE)of the materials was plotted,and it revealed that CTE is the most critical factor in affecting the thermal shock resistance for various ceramic materials.The effect of other factors such as porosity and fracture toughness on the index was also discussed.