A Combined Antenna Array Deployment with High Positioning Accuracy and Low Angular Measurement Error

In this paper,an antenna array composed of circular array and orthogonal linear array is proposed by using the design of long and short baseline“orthogonal linear array”and the circular array ambiguity resolution design of multi-group baseline clustering.The effectiveness of the antenna array in this paper is verified by sufficient simulation and experiment.After the system deviation correction work,it is found that in the L/S/C/X frequency bands,the ambiguity resolution probability is high,and the phase difference system error between each channel is basically the same.The angle measurement error is less than 0.5°,and the positioning error is less than 2.5 km.Notably,as the center frequency increases,calibration consistency improves,and the calibration frequency points become applicable over a wider frequency range.At a center frequency of 11.5 GHz,the calibration frequency point bandwidth extends to 1200 MHz.This combined antenna array deployment holds significant promise for a wide range of applications in contemporary wireless communication systems.

System error iterative identification for underwater positioning based on spectral clustering

The observation error model of the underwater acous-tic positioning system is an important factor to influence the positioning accuracy of the underwater target.For the position inconsistency error caused by considering the underwater tar-get as a mass point,as well as the observation system error,the traditional error model best estimation trajectory(EMBET)with little observed data and too many parameters can lead to the ill-condition of the parameter model.In this paper,a multi-station fusion system error model based on the optimal polynomial con-straint is constructed,and the corresponding observation sys-tem error identification based on improved spectral clustering is designed.Firstly,the reduced parameter unified modeling for the underwater target position parameters and the system error is achieved through the polynomial optimization.Then a multi-sta-tion non-oriented graph network is established,which can address the problem of the inaccurate identification for the sys-tem errors.Moreover,the similarity matrix of the spectral cluster-ing is improved,and the iterative identification for the system errors based on the improved spectral clustering is proposed.Finally,the comprehensive measured data of long baseline lake test and sea test show that the proposed method can accu-rately identify the system errors,and moreover can improve the positioning accuracy for the underwater target positioning.

Uncertainties in landslide susceptibility prediction:Influence rule of different levels of errors in landslide spatial position

The accuracy of landslide susceptibility prediction(LSP)mainly depends on the precision of the landslide spatial position.However,the spatial position error of landslide survey is inevitable,resulting in considerable uncertainties in LSP modeling.To overcome this drawback,this study explores the influence of positional errors of landslide spatial position on LSP uncertainties,and then innovatively proposes a semi-supervised machine learning model to reduce the landslide spatial position error.This paper collected 16 environmental factors and 337 landslides with accurate spatial positions taking Shangyou County of China as an example.The 30e110 m error-based multilayer perceptron(MLP)and random forest(RF)models for LSP are established by randomly offsetting the original landslide by 30,50,70,90 and 110 m.The LSP uncertainties are analyzed by the LSP accuracy and distribution characteristics.Finally,a semi-supervised model is proposed to relieve the LSP uncertainties.Results show that:(1)The LSP accuracies of error-based RF/MLP models decrease with the increase of landslide position errors,and are lower than those of original data-based models;(2)70 m error-based models can still reflect the overall distribution characteristics of landslide susceptibility indices,thus original landslides with certain position errors are acceptable for LSP;(3)Semi-supervised machine learning model can efficiently reduce the landslide position errors and thus improve the LSP accuracies.

New Three-Dimensional Assessment Model and Optimization of Acoustic Positioning System

This paper addresses the problem of assessing and optimizing the acoustic positioning system for underwater target localization with range measurement.We present a new three-dimensional assessment model to evaluate the optimal geometric beacon formation whether meets user requirements.For mathematical tractability,it is assumed that the measurements of the range between the target and beacons are corrupted with white Gaussian noise with variance,which is distance-dependent.Then,the relationship between DOP parameters and positioning accuracy can be derived by adopting dilution of precision(DOP)parameters in the assessment model.In addition,the optimal geometric beacon formation yielding the best performance can be achieved via minimizing the values of geometric dilution of precision(GDOP)in the case where the target position is known and fixed.Next,in order to ensure that the estimated positioning accuracy on the region of interest satisfies the precision required by the user,geometric positioning accuracy(GPA),horizontal positioning accuracy(HPA)and vertical positioning accuracy(VPA)are utilized to assess the optimal geometric beacon formation.Simulation examples are designed to illustrate the exactness of the conclusion.Unlike other work that only uses GDOP to optimize the formation and cannot assess the performance of the specified size,this new three-dimensional assessment model can evaluate the optimal geometric beacon formation for each dimension of any point in three-dimensional space,which can provide guidance to optimize the performance of each specified dimension.

Calculation and correction of magnetic object positioning error caused by magnetic field gradient tensor measurement

Magnetic field gradient tensor measurement is an important technique to obtain position information of magnetic objects. When using magnetic field sensors to measure magnetic field gradient as the coefficients of tensor, field differentiation is generally approximated by field difference. As a result, magnetic objects positioning by magnetic field gradient tensor measurement always involves an inherent error caused by sensor sizes, leading to a reduction in detectable distance and detectable angle. In this paper, the inherent positioning error caused by magnetic field gradient tensor measurement is calculated and corrected by iterations based on the systematic position error distribution patterns. The results show that, the detectable distance range and the angle range of an ac magnetic object（2.44 Am^2@1 kHz） can be increased from（0.45 m, 0.75 m）,（0？, 25？） to（0.30 m, 0.80 m）,（0？,80？）, respectively.

Data-processing induced GPS-positioning error

Global Positioning System data processing is affected by many non-tectonic factors, including the common-mode errors （CME） in station-position time series. The characteristics and origins of CME are still not clear, due to uneven distribution of global GPS networks and the lack of reliable data of the position time series. In this work, data from 241 continuous GPS stations were reprocessed in a consistent way and the results were compared with those generated at Jet Propulsion Laboratory （JPL）. Improvements of residual positions were obtained for many low-quality stations, especially those located in Asia and Australia.

Three-dimensional positions of scattering centers reconstruction from multiple SAR images based on radargrammetry

A method and procedure is presented to reconstruct three-dimensional(3D) positions of scattering centers from multiple synthetic aperture radar(SAR) images. Firstly, two-dimensional(2D) attribute scattering centers of targets are extracted from 2D SAR images. Secondly, similarity measure is developed based on 2D attributed scatter centers' location, type, and radargrammetry principle between multiple SAR images. By this similarity, we can associate 2D scatter centers and then obtain candidate 3D scattering centers. Thirdly, these candidate scattering centers are clustered in 3D space to reconstruct final 3D positions. Compared with presented methods, the proposed method has a capability of describing distributed scattering center, reduces false and missing 3D scattering centers, and has fewer restrictionson modeling data. Finally, results of experiments have demonstrated the effectiveness of the proposed method.

Influence of positioning errors of optical shaping components for single emitter laser diode on beam shaping effects

Beam shaping is required for semiconductor lasers to achieve high optical fiber coupling efficiency in many applications.But the positioning errors on optics may reduce beam shaping effects,and then lead to low optical fiber coupling efficiency.In this work,the positioning errors models for the single emitter laser diode beam shaping system are established.Moreover,the relationships between the errors and the beam shaping effect of each shapers are analysed.Subsequently,the relationship between the errors and the optical fiber coupling efficiency is analysed.The result shows that position errors in the Z axis direction on the fast axis collimator have the greatest influence on the shaping effect,followed by the position errors in the Z axis direction on the converging lens,which should be strictly suppressed in actual operation.Besides,the position errors have a significant influence on the optical fiber coupling efficiency and need to be avoided.

Effects of laser beam divergence angle on airborne LIDAR positioning errors

The influence of laser beam divergence angle on the positioning accuracy of scanning airborne light detection and ranging （LIDAR） is analyzed and simulated. Based on the data process and positioning principle of airborne LIDAR, the errors from pulse broadening induced by laser beam di vergence angle are modeled and qualitatively analyzed for different terrain surfaces. Simulated results of positioning errors and suggestions to reduce them are given for the flat surface, the downhill of slope surface, and the uphill surface.

Laser Interferometer Based Measurement for Positioning Error Compensation in Cartesian Multi-Axis Systems

Accuracy is one of the most important key indices to evaluate multi-axis systems’ (MAS’s) characteristics and performances. The accuracy of MAS’s such as machine tools, measuring machines and robots is adversely affected by various error sources, including geometric imperfections, thermal deformations, load effects, and dynamic disturbances. The increasing demand for higher dimensional accuracy in various industrial applications has created the need to develop cost-effective methods for enhancing the overall performance of these mechanisms. Improving the accuracy of a MAS by upgrading the physical structure would lead to an exponential increase in manufacturing costs without totally eliminating geometrical deviations and thermal deformations of MAS components. Hence, the idea of reducing MAS’s error by a software-based alternative approach to provide real-time prediction and correction of geometric and thermally induced errors is considered a strategic step toward achieving the full potential of the MAS. This paper presents a structured approach designed to improve the accuracy of Cartesian MAS’s through software error compensation. Four steps are required to develop and implement this approach: (i) measurement of error components using a multidimensional laser interferometer system, (ii) tridimensional volumetric error mapping using rigid body kinematics, (iii) volumetric error prediction via an artificial neural network model, and finally (iv) implementation of the on-line error compensation. An illustrative example using a bridge type coordinate measuring machine is presented.

Cone beam computed tomography-guided differences among registration methods for lung cancer and the effects of tumor position,treatment model,and tumor size on positioning errors

Objective To explore the differences in three different registration methods of cone beam computed tomography(CBCT)-guided down-regulated intense radiation therapy for lung cancer as well as the effects of tumor location,treatment mode,and tumor size on registration.Methods This retrospective analysis included 80 lung cancer patients undergoing radiotherapy in our hospital from November 2017 to October 2019 and compared automatic bone registration,automatic grayscale(t+r)registration,and automatic grayscale(t)positioning error on the X-,Y-,and Z-axes under three types of registration methods.The patients were also grouped according to tumor position,treatment mode,and tumor size to compare positioning errors.Results On the X-,Y-,and Z-axes,automatic grayscale(t+r)and automatic grayscale(t)registration showed a better trend.Analysis of the different treatment modes showed differences in the three registration methods;however,these were not statistically significant.Analysis according to tumor sizes showed significant differences between the three registration methods(P<0.05).Analysis according to tumor positions showed differences in the X-and Y-axes that were not significant(P>0.05),while the autopsy registration in the Z-axis showed the largest difference in the mediastinal and hilar lymph nodes(P<0.05).Conclusion The treatment mode was not the main factor affecting registration error in lung cancer.Three registration methods are available for tumors in the upper and lower lungs measuring<3 cm;among these,automatic gray registration is recommended,while any gray registration method is recommended for tumors located in the mediastinal hilar site measuring<3 cm and in the upper and lower lungs≥3 cm.

Geometric Error Identification of Gantry-Type CNC Machine Tool Based on Multi-Station Synchronization Laser Tracers

Laser tracers are a three-dimensional coordinate measurement system that are widely used in industrial measurement.We propose a geometric error identification method based on multi-station synchronization laser tracers to enable the rapid and high-precision measurement of geometric errors for gantry-type computer numerical control(CNC)machine tools.This method also improves on the existing measurement efficiency issues in the single-base station measurement method and multi-base station time-sharing measurement method.We consider a three-axis gantry-type CNC machine tool,and the geometric error mathematical model is derived and established based on the combination of screw theory and a topological analysis of the machine kinematic chain.The four-station laser tracers position and measurement points are realized based on the multi-point positioning principle.A self-calibration algorithm is proposed for the coordinate calibration process of a laser tracer using the Levenberg-Marquardt nonlinear least squares method,and the geometric error is solved using Taylor’s first-order linearization iteration.The experimental results show that the geometric error calculated based on this modeling method is comparable to the results from the Etalon laser tracer.For a volume of 800 mm×1000 mm×350 mm,the maximum differences of the linear,angular,and spatial position errors were 2.0μm,2.7μrad,and 12.0μm,respectively,which verifies the accuracy of the proposed algorithm.This research proposes a modeling method for the precise measurement of errors in machine tools,and the applied nature of this study also makes it relevant both to researchers and those in the industrial sector.

Effects of the initiation position on the damage and fracture characteristics of linear-charge blasting in rock

To study the effects of the initiation position on the damage and fracture characteristics of linear-charge blasting, blasting model experiments were conducted in this study using computed tomography scanning and three-dimensional reconstruction methods. The fractal damage theory was used to quantify the crack distribution and damage degree of sandstone specimens after blasting. The results showed that regardless of an inverse or top initiation, due to compression deformation and sliding frictional resistance, the plugging medium of the borehole is effective. The energy of the explosive gas near the top of the borehole is consumed. This affects the effective crushing of rocks near the top of the borehole, where the extent of damage to Sections Ⅰ and Ⅱ is less than that of Sections Ⅲ and Ⅳ. In addition, the analysis revealed that under conditions of top initiation, the reflected tensile damage of the rock at the free face of the top of the borehole and the compression deformation of the plug and friction consume more blasting energy, resulting in lower blasting energy efficiency for top initiation. As a result, the overall damage degree of the specimens in the top-initiation group was significantly smaller than that in the inverse-initiation group. Under conditions of inverse initiation, the blasting energy efficiency is greater, causing the specimen to experience greater damage. Therefore, in the engineering practice of rock tunnel cut blasting, to utilize blasting energy effectively and enhance the effects of rock fragmentation, using the inverse-initiation method is recommended. In addition, in three-dimensional(3D) rock blasting, the bottom of the borehole has obvious end effects under the conditions of inverse initiation, and the crack distribution at the bottom of the borehole is trumpet-shaped. The occurrence of an end effect in the 3D linear-charge blasting model experiment is related to the initiation position and the blocking condition.

Error Analysis on the Positioning Accuracy of a Pneumatic Vibration Isolator

A method of error analysis on the positioning accuracy of a pneumatic vibration isolator was proposed.First,the necessity of positioning accuracy was studied,in addition to the key factors associated with positioning accuracy.These analyses indicated that the positioning accuracy of the pneumatic vibration isolator was mainly attributed to the position error of the push button and the gap between the spindle and valve stem.Second,the error model of the positioning accuracy of the pneumatic vibration isolator was established through geometric simplification and geometric calculation.There are different methods used to calculate the position error of the push button for the different valves.Finally,an example analysis evaluating the impact of a specific two-position three-way valve on the positioning accuracy was given by means of error distribution.Experimental results validated the accuracy of the error model and the example analysis.This error model can be used to guide the structural parameter optimization design according to the requirements for positioning accuracy.

Endemic error correction model and quantitative analysis of precise point positioning

To identify the endemic error of the precise point positioning which cannot be weakened or eliminated in precise point positioning (PPP) zero-difference model, the 24 h observation data acquired from CHAN station on Oct 31st, 2010, were adopted for analyses, different correction models of various errors were discussed and their influences on traditional zero-difference model were analyzed. The results show that the errors cannot be ignored. They must be corrected with suitable models and estimated with auxiliary parameters. The influence magnitudes of all errors are defined, and the results have guiding significance to improve the accuracy of precise point positioning zero-difference model.

A Radiotherapy Treatment Margin Formula When Systematic Positioning Errors are Relatively Small Compared to Random Positioning Errors: A First-Order Approximation

A radiotherapy treatment margin formula has been analytically derived when a standard deviation (SD) of systematic positioning errors &#425;is relatively small compared to an SD of random positioning errors &sigma;. The margin formula for 0 ≤ &#425;≤ &sigma;was calculated by linearly interpolating two boundaries at &#425;= 0 and &#425;= &sigma;, assuming that the van Herk margin approximation of k1&#425;+ k2&sigma;is valid at &#425;= &sigma;. It was shown that a margin formula for 0 ≤ &#425;≤ &sigma;may be approximated by k1&sigma;+ k2&#425;, leading to a more general form of k1 max(&#425;,&sigma;) + k2 min(&#425;,&sigma;) which is a piecewise linear approximation for any values of &#425;and &sigma;.

Research on Positioning Error Compensation for Micro Milling Machine Tool

Micro milling has many advantages in fabricating three-dimensional(3D) structure in micrometer scale. The micro milling machine tool with high positioning accuracy is of great importance for getting micro structure with high profile precision and good surface quality. Meanwhile, the method of position error compensation is a good way to improve the accuracy of the micro milling machine tools. In this paper,a software method is adopted to compensate the positioning error and improve the positioning accuracy. According to error cancellation theory,the compensation values are generated and compensation tables are built to adjust the positioning error in the NC system based on Industrial Motion and Automation Control( IMAC). The positioning accuracy of linear motor is ± 0. 3 μm without backlash after compensation. In order to verify the effectiveness of compensation on the machining performance,concave spherical surfaces are processed on the micro milling machine tool. The experimental results show that the profile radius error of the spherical surface machined with compensation decreases more than 60%.

Far-Field Pattern Reconstruction from Positioning Errors Affected Near-Field Data Acquired via Helicoidal Scanning

In this paper, an effective technique to compensate the positioning errors in a near-field—far-field (NF-FF) transformation with helicoidal scanning for elongated antennas is presented and validated both numerically and experimentally. It relies on a nonredundant sampling representation of the voltage measured by the probe, obtained by considering the antenna as enclosed in a cylinder ended in two half-spheres. An iterative scheme is used to reconstruct the helicoidal NF data at the points fixed by the representation from the acquired irregularly spaced ones. Once the helicoidal data have been retrieved, those needed by a classical NF-FF transformation with cylindrical scanning are efficiently evaluated by using an optimal sampling interpolation algorithm. Some numerical tests, assessing the accuracy of the approach and its stability with respect to random errors affecting the data, are reported. Experimental tests performed at the Antenna Characterization Lab of the University of Salerno further confirm the validity of the proposed technique.

Integration system research and development for three-dimensional laser scanning information visualization in goaf

An integration processing system of three-dimensional laser scanning information visualization in goaf was developed. It is provided with multiple functions, such as laser scanning information management for goaf, cloud data de-noising optimization, construction, display and operation of three-dimensional model, model editing, profile generation, calculation of goaf volume and roof area, Boolean calculation among models and interaction with the third party soft ware. Concerning this system with a concise interface, plentiful data input/output interfaces, it is featured with high integration, simple and convenient operations of applications. According to practice, in addition to being well-adapted, this system is favorably reliable and stable.

Effect of the firing position on aiming error and probability of hit

Sources of dispersions that contribute to delivery error and reduce the soldier performance in terms of hit probability are numerous.In order to improve the warfighter performance,the source of the errors contributing to the inaccuracy and dispersion of the weapon systems must be understood.They include ammunition dispersion error,gun dispersion,aerodynamic jump and the aiming error.The aiming error or gun pointing error is defined as the angle between the gun muzzle at the instant the trigger is pulled and the line of fire that corresponds to the intendent aim point.This is a round-to-round error.In weapons systems that include the rifle,the ammunition,a sight and a gunner,the aiming error was shown to be the single most important source of dispersion for the regular infantryman.In other words,for the general purpose rifle weapon system,the weak link is often the human.In order to verify and quantify this assertion,an experimental investigation was carried out to determine the aiming error associated with general purpose rifle fired by infantryman.The aiming error was evaluated for various firing positions and scenarios using infantryman for ranges varying between 100 m and 500 m.The results show that the aiming error is the main contributor to dispersion for the general purpose rifle fired by a non-specialized infantryman.The aiming error induced dispersion for unstressed and rested gunners is shown to be at best equivalent to that of the weapon fired from a bench rest by a marksman.Crown Copyright(?) 2019 Production and hosting by Elsevier B.V.on behalf of China Ordnance Society.