Optimization of Wickerhamomyces anomalus Fermentation Conditions for Pectinase Production Based on Wet Processing of Arabica Coffee in Yunnan Province

In order to improve the pectin-degrading efficiency in wet processing of Arabica coffee in Yunnan, Box-Behnken design and single factor experiment were used to optimize the fermentation conditions of five pectinolytic Wickerhamomyces anomalus strains from the fermentation broth of Arabica coffee in Baoshan, Yunnan during wet processing with pectase activity as an indicator. The results showed that the five strains all synthesized pectin lyase(PL), polygalacturonase(PG), and pectin methylesterase(PM).Among them, strain CAP5 had strong ability to produce PG and PL,while strain CAP4 secreted a large amount of PM. Under optimized conditions, the activity of PG, PL, and PM of the five strains came in at 250.17~411.20 U/mL, 12.98~16.55 U/mL, and 208.52~322.83 U/mL,respectively. The four factors of nitrogen source concentration,fermentation time, Mn2+ concentration, and pH value were optimized and the optimal pectinase-producing fermentation conditions for five strains were as follows: peptone 2.2 g/L, fermentation time 30 h, Mn2+ 1.5 mmol/L, and pH 4.3. After fermentation under the optimized conditions, the maximum PG activity of CAP5 amounted to 411.20 U/mL, 114.03% higher than that before optimization.Meanwhile, the PG activity of strains CAP3, CAP4, CAP8, and CAP10 increased by 86.74%, 114.55%, 65.79%, and 66.07%,respectively, and the activity of PL and PM of the five strains rose 150.35%~218.56% and 341.07%~418.52%, respectively. These findings suggested that W. anomalus strains could be used as coffee starter and had great potential for the lysis of pectin.

Wet Coffee Processing Discharges Affecting Quality of River Water at Kayanza Ecological Zone, Burundi

Wet coffee processing leads to the generation of large volumes of wastewater, whose discharge to the environment leads to pollution of freshwater bodies. Kayanza is a major coffee growing area in Burundi with more than 40 wet coffee processing factories (WCPF) that discharge effluents directly to receiving water bodies without treatment. This study was carried out to assess the effect of coffee wastewater on the physicochemical properties of receiving waterbodies in Kayanza coffee growing ecological zone. Currently, no study has been done to analyze the effluent from the WCPF and assess the level of pollution. This study will therefore provide valuable data on the water pollution from coffee processing plants. Ten (10) rivers in the Kayanza coffee growing zone were studied during the months of April and June, 2020. Water samples were collected upstream (U) and downstream (D) of the effluent discharge points in triplicate. Samples were analyzed for pH, Chemical Oxygen Demand (COD), Biochemical Oxygen Demand (BOD5), Temperature, Salinity, Electrical Conductivity (EC), Total Dissolved Solids (TDS), Dissolved Oxygen (DO), Total Suspended Solids (TSS), Nitrates, Nitrites, Lead (Pb), Copper (Cu), Chlorides and Ammonium ions using standard methods. Physical parameters were analyzed in situ whereas chemical parameters were analyzed in the laboratories in Burundi Institute of Agricultural Sciences (ISABU) and University of Burundi. Data were analyzed using R-studio-1.0.153, GenStat 64-bit Release 14.1 and SSPS. Results on the physicochemical parameters indicated that coffee factory effluent has a polluting potential during coffee processing peak. The concentrations of the physicochemical parameters were significantly (p < 0.05) higher downstream (D) compared to upstream (U) of the river water sampling points. All downstream sites had COD, BOD5, TSS and pH values above allowable limits set by WHO and Burundi. The polluting impact of public wet coffee processing factories was significantly higher than that of private and cooperatives owned factories (p < 0.05). Measures should be taken in order to protect water bodies.

Study on the Genetics and Development of Fiber Pigments and Color Deviation After Wetting Process of Naturally Colored Cotton

The genetic control of fiber pigment color in naturally colored cotton was studied. The expression of brown and green fiber color was controlled by incompletely dominant single genes and incompletely dominant major genes, respectively. Production and accumulation of the fiber pigment were related to special expression of enzymatic genes for pigment synthesis in fiber cells. At the stage of fiber lengthening, naturally colored cotton, like white cotton, appeared purely white. But when fiber cell walls entered the thickening stage, pigment appeared by degrees. When the fiber was completely matured (on boll dehiscence), the color reached its darkest level. After wetting process treatment, the hues of the fiber pigment changed in regular patterns. The hue circle for brown and green cotton changed in the opposite direction with wetting process treatment. In general, the treated cotton color and luster became dark and vivid, and this trend provided the possibility for enhancing the fiber quality by suitable environmental friendly finishing. The analysis showed that the color and luster of the cotton may be controlled by a series of pigments which show different chemical performance.

Response of Freezing/Thawing Indexes to the Wetting Trend under Warming Climate Conditions over the Qinghai–Tibetan Plateau during 1961–2010:A Numerical Simulation

Since the 1990s,the Qinghai–Tibetan Plateau(QTP)has experienced a strikingly warming and wetter climate that alters the thermal and hydrological properties of frozen ground.A positive correlation between the warming and thermal degradation in permafrost or seasonally frozen ground(SFG)has long been recognized.Still,a predictive relationship between historical wetting under warming climate conditions and frozen ground has not yet been well demonstrated,despite the expectation that it will become even more important because precipitation over the QTP has been projected to increase continuously in the near future.This study investigates the response of the thermal regime to historical wetting in both permafrost and SFG areas and examines their relationships separately using the Community Land Surface Model version 4.5.Results show that wetting before the 1990s across the QTP mainly cooled the permafrost body in the arid and semiarid zones,with significant correlation coefficients of 0.60 and 0.48,respectively.Precipitation increased continually at the rate of 6.16 mm decade–1 in the arid zone after the 1990s but had a contrasting warming effect on permafrost through a significant shortening of the thawing duration within the active layer.However,diminished rainfall in the humid zone after the 1990s also significantly extended the thawing duration of SFG.The relationship between the ground thawing index and precipitation was significantly negatively correlated(−0.75).The dual effects of wetting on the thermal dynamics of the QTP are becoming critical because of the projected increases in future precipitation.

Engineering practice and economic analysis of ozone oxidation wet denitrification technology

SO_(2)and NO emitted from coal-fired power plants have caused serious air pollution in China.In this study,a test system for NO oxidation using O_(3)is established.The basic characteristics of NO oxidation and products forms are studied.A separate test system for the combined removal of SO_(2)and NO_(x)is also established,and the absorption characteristics of NO_(x)are studied.The characteristics of NO oxidation and NO_(x)absorption were verified in a 35 t·h^(-1)industrial boiler wet combined desulfurization and denitrification project.The operating economy of ozone oxidation wet denitrification technology is analyzed.The results show that O_(3)has a high rate and strong selectivity for NO oxidation.When O_(3)is insufficient,the primary oxidation product is NO_(2).When O_(3)is present in excess,NO_(2)continues to get oxidized to N_(2)O_(5)or NO_(3).The removal efficiency of NO_(2)in alkaline absorption system is low(only about 15%).NOx removal efficiency can be improved by oxidizing NO_(x)to N_(2)O_(5)or NO_(3)by increasing ozone ratio.When the molar ratio of O_(3)/NO is 1.77,the NOx removal efficiency reaches 90.3%,while the operating cost of removing NO_(x)per kilogram is 6.06 USD(NO_(2)).

Effect of Wet Surface Treated Nano-SiO_2 on Mechanical Properties of Polypropylene Composite

Nano-SiO2/polypropylene composite was prepared by melt-blending process. The nano-SiO2 particles were organized by wet process surface treatment with silane coupling agent KH-570. The effect of mass fraction of nano-SiO2 particles and dosage of KH-570 on the toughening and strengthening of PP matrix were investigated based on the fractography of impact notch and the analysis of crystal structure by X-ray and dispersive structure of nano-SiO2 by TEM. Results show that the impact and flexural strength and modulus of the composite are improved obviously with low loading of nano-SiO2 （3 wt%-5 wt%）, and the izod impact strength of PP increases twice with 4 wt% nano-SiO2. The nano-SiO2 particles treated can disperse into the matrix resin, which has evident heterogeneous nucleation effects on the crystallization of PP. The optimal toughening and strengthening effects of PP matrix can be obtained when the content of nano-SiO2 and KH-570 are 4 wt% and 3 wt%, respectively.

Simulation of Wetting and Drying Processes in A Depth Integrated Shallow Water Flow Model by Slot Method

A particular porosity method named ＂slot method＂ is implemented in a depth-integrated shallow water flow model （DIVAST） to simulate wetting and drying processes. Discussed is the relationship between the shape factors of the ＂slot＂ and the preset depth used in ＂wetting-drying＂ algorithm. Two typical tests are conducted to examine the performance of the method with the effect of the shape factors of the ＂slot＂ being checked in detail in the first test. Numerical results demonstrate that： 1 ） no additional effort to improve the finite difference scheme is needed to implement ＂slot method＂ in DIVAST, and 2） ＂slot method＂ will simulate wetting and diying processes correctly if the shape factors of the ＂slot＂ being selected properly.

Various Methods Used for the Treatment of the Wet-Phosphoric Acid

Phosphoric acid obtained by the wet process is laden with impurities which limit its use in fertilizers. To expand its range of use, various methods have been proposed to purify it which range from simple fading-clarification to more complex operations. These processes include essentially the liquid-liquid extraction, chemical precipitation, ion flotation, adsorption on activated carbon, ion exchange resins. However, the use of these techniques is limited to a number of disadvantages such as high operational cost, environmental pollution, complicated process, limited effectiveness, etc.. Our contribution for this domain （purification of wet-phosphoric acid） consists to use clays which could be adsorbent materials alternative to both economic and less polluting. These are phyllosilicates which have a large adsorption capacity due to their large specific surface and their surface charge. In this study, we will detail the processes which present great importance for the treatment of wet phosphoric acid.

THERMAL PROCESS OF VACUUM FLUXLESS LASER SOLDERING AND ANALYSIS ON SOLDER SPREADING AND WETTING

In order to study the mechanism of vacuum fluxless soldering on the conditions of laser heating, the method of measuring temperature by the thermocouple is used to analyze the spreading and wetting process of both fluxless Sn-Pb solder in the vacuum surroundings and flux Sn-Pb solder on Cu pad. Solder spreading and wetting affected by the soldering thermal process is also discussed according to the thermodynamics principle. Results show that vacuum fluxless soldering demands higher temperature, and the fall of the solder surface tension is the important factor achieving fluxless laser soldering.

The Properties of Sulfur Rubber Concrete (SRC)

The mix designs and specimen preparation for the dry process and wet process of sulfur rubber conerete （ SRC ） were investigated. The compressive strength, corrosion-resistance and toughness were studied and discussed. The results show that SRC is corrosion-resistanet. Although the compressive strength of SRC decreases with inereasing rubber content, the toughness increases instead . Adding micro-filler will improve the compressive strength of SRC . There is a threshold value for the sulfur content, at which the compressive strength and the workability of SRC reach an optimum balance . The bond between rubber particles and surrounding sulfur is strong due to the vulcanization process that generates cross-link through S-C bonds.

Performance and mechanism of CO_(2) absorption during the simultaneous removal of SO_(2) and NO_(x) by wet scrubbing process

The co-removal of CO_(2)while removing SO_(2)and NOxfrom industrial flue gas has great potential of carbon emission reduction but related research is lacking.In this study,a wet scrubbing process with various urea solutions for desulfurization and denitrification was explored for the possibility of CO_(2)absorption.The results showed that the urea-additive solutions were efficient for NOxand SO_(2)abatement,but delivered<10%CO_(2)absorption efficiency.The addition of Ca(OH)_(2)dramatically enhanced the CO_(2)absorption,remained the desulfurization efficiency,unfortunately restricted the denitrification efficiency.Among various operating parameters,pH of solution played a determining role during the absorption.The contradictory pH demands of CO_(2)absorption and denitrification were observed and discussed in detail.A higher pH of solution than 10 was favorable for CO_(2)absorption,while the oxidizing of NO to NO_(2),NO_(2)^(-)or NO_(3)^(-)by NaClO_(2)was inhibited in this condition.When7<pH<10,it was favorable for the conversion and absorption of NO and NOx.However,the conversion of HCO_(3)^(-)to CO_(3)^(2-)was significantly inhibited,hence preventing the absorption of CO_(2).Large part of Ca(OH)_(2)became CaCO_(3)with a finer particle size,which covered the unreacted Ca(OH)_(2)surface after the reaction.Kinetic analysis showed that the CO_(2)absorption in urea-NaClO_(2)-Ca(OH)_(2)absorbent was controlled by chemical reaction in early stage,then by ash layer diffusion in later stage.

Ultrasonic attenuation spectroscopy for multivariate statistical process control in nanomaterial processing

Ultrasonic attenuation spectroscopy （UAS） is an attractive process analytical technology （PAT） for on-line real-time characterisation of slurries for particle size distribution （PSD） estimation. It is however only applicable to relatively low solid concentrations since existing instrument process models still cannot fully take into account the phenomena of particle-particle interaction and multiple scattering, leading to errors in PSD estimation. This paper investigates an alternative use of the raw attenuation spectra for direct multivariate statistical process control （MSPC）. The UAS raw spectra were processed using principal component analysis. The selected principal components were used to derive two MSPC statistics, the Hotelling＇s T2 and square prediction error （SPE）. The method is illustrated and demonstrated by reference to a wet milling process for processinR nanoparticles.

Accelerated oxidation of VOCs via vacuum ultraviolet photolysis coupled with wet scrubbing process

Vacuum ultraviolet(VUV) photolysis is a facile method for volatile organic compounds(VOCs) elimination, but is greatly limited by the relatively low removal efficiency and the possible secondary pollution. To overcome above drawbacks, we developed an efficient method for VOCs elimination via VUV photolysis coupled with wet scrubbing process. In this coupled process, volatile toluene, a representative of VOCs, was oxidized by the gas-phase VUV photolysis, and then scrubbed into water for further oxidation by the liquid-phase VUV photolysis. More than 96% of toluene was efficiently removed by this coupled process, which was 2 times higher than that in the gas-phase VUV photolysis. This improvement was attributed to the synergistic effect between gas-phase and liquid-phase VUV photolysis. O3and HO·are the predomination reactive species for the toluene degradation in this coupled process, and the generation of O3in gas-phase VUV photolysis can efficiently enhance the HO·production in liquid-phase VUV photolysis. The result from in-situ proton transfer reaction ionization with mass analyzer(PTR-MS) further suggested that most intermediates were trapped by the wet scrubbing process and efficiently oxidized by the liquid-phase VUV photolysis, showing a high performance for controlling the secondary pollution. Furthermore, the result of stability test and the reuse of solution demonstrated that this coupled process has a highly stable and sustainable performance for toluene degradation. This study presents an environmentally benign and highly efficient VUV photolysis for gaseous VOCs removal in the wet scrubbing process.

Fe203-CeO2-Bi203/y-AI203 catalyst in the catalytic wet air oxidation （CWAO） of cationic red GTL under mild reaction conditions

The Fe203-CeO2-Bi203/-A1203 catalyst, a novel environmental-friendly material, was used to investigate the catalytic wet air oxidation （CWAO） of cationic red GTL under mild operating conditions in a batch reactor. The catalyst was prepared by wet impregnation, and characterized by special surface area （BET measurement）, X-ray diffraction （XRD） and X-ray photoelectron spectroscopy （XPS）. The Fe203-CeO2-]]i203/qt-A1203 catalyst exhibited good catalytic activity and stability in the CWAO under atmosphere pressure. The effect of the reaction conditions （catalyst loading, degradation temperature, solution concentration and initial solution pH value） was studied. The result showed that the decolorization efficiency of cationic red GTL was improved with increasing the initial solution pH value and the degradation temperature. The apparent activation energy for the reaction was 79 kJ. mo1-1. Hydroperoxy radicals （HO2.） and superoxide radicals （O2-） appeared as the main reactive species upon the CWAO of cationic red GTL.

Synthesis and Properties of Novel Polyimide Fibers Containing Phosphorus Groups in the Side Chain (DATPPO)

A series of polyamic acid copolymers(co-PAAs) containing phosphorous groups in the side chains were synthesized from [2,5-bis(4-aminophenoxy) phenyl] diphenylphosphine oxide(DATPPO) and 4,4′-oxydianiline(ODA) with 3,3′,4,4′-biphenyltetracarboxylic dianhydride(s-BPDA) through the polycondensation in N,N′-dimethyacetamide(DMAc). The co-PAA solutions were spun into fibers by a dry-jet wet spinning process followed by thermal imidization to obtain co-polyimide(co-PI) fibers. FTIR spectra and elemental analysis confirmed the chemical structure of PI fibers. SEM results indicated that the resulting PI fibers had a smooth and dense surface, a uniform and circle-shape diameter. The thermogravimetric measurements showed that with the increase of DATPPO content, the resulting PI fibers possessed high decomposition temperature and residual char yield, indicating that the PI fibers had good thermal stability. The corresponding limiting oxygen index(LOI) values from the experiment results showed that the co-PI fibers possessed good flame-retardant property. Furthermore, the mechanical properties of the co-PI fibers were investigated systematically. When the DATPPO content increased, the tensile strength and initial modulus of the co-PI fibers decreased. However, the mechanical properties were improved by increasing the draw ratio of the fibers. When the draw ratio was up to 2.5, the tensile strength and initial modulus of the co-PI fibers reached up to 0.64 and 10.02 GPa, respectively. The WAXD results showed that the order degree of amorphous matter increased with increased stretching. In addition, the SAXS results displayed that valuably drawing the fibers could eliminate the voids inside and lead to better mechanical property. WAXD revealed that the orientation of the amorphous polymer influenced the mechanical properties of the fibers.