Investigation of working pressure on the surface roughness controlling technology of glow discharge polymer films based on the diagnosed plasma

The effects of working pressure on the component, surface morphology, surface roughness, and deposition rate of glow discharge polymer （GDP） films by a trans-2-butene/hydrogen gas mixture were investigated based on plasma characteristics diagnosis. The composition and ion energy distributions of a multi-carbon （CaHs/H2） plasma mixture at different working pressures were diagnosed by an energy-resolved mass spectrometer （MS） during the GDP film deposition process. The Fourier transform infrared spectroscopy （FT-IR）, field emission scanning electron microscope （SEM） and white-fight interferometer （WLI） results were obtained to investigate the structure, morphology and roughness characterization of the deposited films, respectively. It was found that the degree of ionization of the C4H8/H2 plasma reduces with an increase in the working pressure. At a low working pressure, the C-H fragments exhibited small-mass and high ion energy in plasma. In this case, the film had a low CH3/CH2 ratio, and displayed a smooth surface without any holes, cracks or asperities. While the working pressure increased to 15 Pa, the largest number of large-mass fragments led to the deposition rate reaching a maximum of 2.11 #m h-1, and to hole defects on the film surface. However, continuing to increase the working pressure, the film surface became smooth again, and the interface between clusters became inconspicuous without etching pits.

Influence of Working Pressure on Ion Sensitive Probe Measurement in Microwave ECR Plasmas

In order to precisely measure the ion parameters in a microwave electron cyclotron resonance plasma using an ion sensitive probe,the dependences of the current-voltage（I-V）characteristics on the shielding height（h）and the potential difference between inner and outer electrodes（V_B）have been investigated at different working pressures of 0.03 Pa and 0.8 Pa.Results show that the I-V curves at higher pressure are more sensitive to the variation of h than those at lower pressure.The influence of V_B on ion temperature（T_i）measurement becomes more prominent when the pressure is increased from 0.03 Pa to 0.8 Pa.Under both pressures,the optimized h is obtained at the condition where the current reaches zero in the positive voltage region with a suitable V_B of-1.5 V because of effective shielding of the electron E×B drift.

Preparation and optoelectronic properties of a-IGZO thin films deposited by RF magnetron sputtering at different working pressures

Transparent oxide semiconductor, a-IGZO, thin films were prepared by high-vacuum RF magnetron sputtering at different working pressures. The effect of working pressure on crystal structure, surface morphology, and electrical and optical properties of the films was studied. The highest ball mobility of 17.45 cmZ-V-l.s- 1 is obtained at 0.3 Pa with annealing at 200 ℃, while the highest carrier concentration of 2.32×10^20 cm^-3 and the lowest resistivity of 0.001568 Ω.cm are obtained at 0.45 Pa with annealing. The highest transmittance of 90.9 % is obtained at 0.9 Pa with annealing treatment. A ＂blue shift＂ of UV absorption edge is observed with the increase of working press ure.

WORKING LIQUID PRESSURE AND ITS CONTROL IN HYDRAULIC DRAWING PROCESSES OF CUPS

A method of setting up a pressure-stroke characteristic of the working liquid in hydraulic drawing is studied. A pressure-stroke characteristic and software for controlling its forming process are also developed. And a set of pressure controlling devices with PLC as a central processor are designed. It can be got from the relevant experiments that the pressure-stroke characteristic is correct and its control for forming process is available.

LaB6 Work Function and Structural Stability under High Pressure

The work functions of the （110） and （10（3） surfaces of LaB6 are determined from ambient pressure to 39.1 GPa. The work function of the （110） surface slowly decreases but that of the （100） surface remains at a relatively constant value. To determine the reason for this difference, the electron density distribution （EDD） is determined from high-pressure single-crystal x-ray diffraction data by the maximum entropy method. The EDD results show that the chemical bond properties in LaB6 play a key role also investigated by single-crystal x-ray diffraction. In observed from ambient pressure to 39.1 GPa. The structural stability of LaB6 under high pressure is this study, no structural or electronic phase transition is

Effects of Pressure Stress Work and Viscous Dissipation in Mixed Convection Flow Along a Vertical Flat Plate

The Effects of pressure stress work and viscous dissipation in mixed convection flow along a vertical fiat plate have been investigated. The results are obtained by transforming the governing system of boundary layer equations into a system of non-dimensional equations and by applying implicit finite difference method together with Newton＇s linearization approximation. Numerical results for different values of pressure stress work parameter, viscous dissipation parameter and Prandtl number have been obtained. The velocity profiles, temperature distributions, skin friction co-efficient and the rate of heat transfer have been presented graphically for the effects of the aforementioned parameters.

警察工作压力对身心健康的影响及其对策(下)

In all the occupations which have pressure, the psychological pressure index of police’s work is the highest. This article analyses systematically the source of pressure of police’s work and reaction mechanism of it to effects on sound in body and mind. Then it demonstrates the warning signs and symptoms of the reaction of pressure of police’s work and proposes countermeasures according to the common phenomena of anxiousness and depression.

Compressive and Sealing Characteristics of PTFE under Cyclic Loading-unloading

Compressive and sealing characteristics of PTFE under cyclic loading-unloading at room temperature are studied in order to evaluate the cyclic sealing performance of control valve comprehensively. The unloading characteristics are different from the loading ones, therefore there is hysteresis between the unloading and loading curves. Compressive hysteresis is the main factor that causes sealing hysteresis. The leakage rate of PTFE complies with the power law before it enters the relatively stable region. Lastly, the effect of working pressure on the compressive and sealing characteristics is discussed. The experimental results show that the working pressure has little effect on compressive deformation but has a great influence on leakage rate.

Influence of working gas pressure on the performance of W/Si multilayers

The effect of Ar pressure on the performance of W/Si multilayers is investigated. W/Si multilayers were deposited by a high vacuum DC magnetron sputtering system. The Ar pressure was changed from 1.0 to 5.0 mTorr with an interval of 1.0 mTorr during the deposition process. Electron probe microanalysis and Rutherford backscattering are performed to determine the Ar content incorporated within these multilayers. The results demonstrate that less Ar is incorporated within the sample when more Ar is used in the plasma, which could be explained by the increase of the collision probability and the decrease in the kinetic energy of Ar ions arriving at the substrate when more Ar exists. The grazing incident X-ray reflectivity （GIXR） at 0.154 nm is used to determine the structural parameters of the layers. The results show that the structures of these multilayers prepared at different Ar pressure are very similar and that the interface roughness increases quickly when the Ar pressure is higher than 3.0 mTorr. The measurements of the extreme ultraviolet （EUV） reflectivity indicate that the reflectivity decreases when Ar pressure increases. The fitting results of GIXR and EUV refiectivity curves indicate that with an increase of Ar pressure, the density and decrement of the refractive index are increased for W and decreased for Si, which is mainly due to （1） the decrease in Ar content incorporated within these multilayers which affects their performance and （2） the increase of collision probability for sputtered W and Si, the decrease of their average kinetic energy arriving at the substrate, and thus the loosing of their layers.

The Motivate Effect of Higher Education Institutions' Compensation System on Faculties

Based on the questionnaire survey,this article reveals the effects of the current university compensation system on faculties in three psychological aspects,namely performance exam effect,work pressure and endurance capability.The results indicate that university faculties have a strong pursuit for self-fulfillment and successful career.Most of them love their teaching career and wish to further improve the fairness and efficiency of university management system by deepening the management systemic reform.Multi-leveled,multi-purposed and multi-modeled managing strategy of university compensation system is proved to be the main methods of improving fairness and efficiency.

Intention to Leave and Associated Factors among Health Professionals in Jimma Zone Public Health Centers, Southwest Ethiopia

Background: Inadequate human resources are a major constraint to improving global health. The health sector is characterized by a high turnover coupled with internal as well as external brain drain but there is little information on intention to leave among health professionals in public health centers of Jimma Zone, Oromia Regional State. The aim of this study is to assess intention to leave and associated factors among health professionals in public health centers of Jimma Zone, southwest Ethiopia. Methods: A cross-sectional quantitative and qualitative study was conducted on seven randomly selected woredas (districts) which have 53 public health centers. All health professionals in sampled district public health centers were included (n = 505). Factor analysis was employed for all Likert scale instruments to extract factor(s) representing each of the scales using SPSS version 16.0. The qualitative data was analyzed by thematic analysis methods. Ethical approval was obtained from Jimma University. Results: Four hundred fifty five (90.1%) health professionals participated in the study;out of this, 290 (63.7%) had intention to leave. Among variables, job satisfaction (Beta = -0.298, (95% CI, -0.568 to -0.029), working environment (Beta = -0.612, (95% CI, -0.955 to -0.270), and organizational management (Beta = -0.552, (95% CI, 0.289 to 0.815) had statistically significant association with intention to leave among health professionals in public health centers of Jimma Zone. Conclusions: The overall intention to leave among health professionals was high. Level of job satisfaction, working environment, work pressure, and organizational management had statistically significant association with intention to leave. Thus, responsible bodies should aggressively work on the concerns identified, like, improvements in salary, promotion in terms of training/educational opportunity, improving working environment, and transfer of health professionals, and improvement of the leadership skills of managers.

Effects of extrinsic positive end-expiratory pressure on work of breathing in patients with chronic obstructive pulmonary disease

Objective To investigate the effects of extrinsic positive end-expiratory pressure (PEEPe) on work of breathing in patients with chronic obstructive pulmonary disease (COPD) and their corresponding mechanism.Methods Ten ventilated patients with COPD were included in the study. A Bicore CP-100 pulmonary monitor (Bicore Monitoring System, USA) was used for monitoring respiratory mechanics. First, dynamic intrinsic positive end-expiratory pressure (PEEPi,dyn) was measured when PEEPe was zero, which was called PEEPi,dynz. Then the PEEPe was set randomly at 0%, 40%, 60%, 80% and 100% of PEEPi,dynz respectively. Pulmonary mechanics and other parameters (heart rate, blood pressure and blood gas analysis) were measured 30 minutes after the level of PEEPe was changed.Results Work of breathing patient (WOBp), pressure time product, difference of esophageal pressure and PEEPi,dyn decreased significantly when PEEPe was applied, and continued decreasing as PEEPe was increased. Work of breathing ventilator increased significantly when PEEPe was increased to 80% and 100% of PEEPi,dynz. Significantly positive linear correlation was found between the changes in WOBp and in PEEPi,dyn.Conclusions WOBp decreases gradually as PEEPe is increased. WOBp decreases by narrowing the difference between the alveolus pressure and the central airway pressure at the end of expiration when PEEPe is applied.