Optimizing Optical Attocells Positioning of Indoor Visible Light Communication System

Visible light communication(VLC),which is a prominent emerging solution that complements the radio frequency(RF)technology,exhibits the potential to meet the demands of fifth-generation(5G)and beyond technologies.The random movement of mobile terminals in the indoor environment is a challenge in the VLC system.The model of optical attocells has a critical role in the uniform distribution and the quality of communication links in terms of received power and signal-to-noise ratio(SNR).As such,the optical attocells positions were optimized in this study with a developed try and error(TE)algorithm.The optimized optical attocells were examined and compared with previous models.This novel approach had successfully increased minimum received power from−1.29 to−0.225 dBm,along with enhanced SNR performance by 2.06 dB.The bit error rate(BER)was reduced to 4.42×10−8 and 6.63×10−14 by utilizing OOK-NRZ and BPSK modulation techniques,respectively.The optimized attocells positions displayed better uniform distribution,as both received power and SNR performances improved by 0.45 and 0.026,respectively.As the results of the proposed model are optimal,it is suitable for standard office and room model applications.

Low Complexity Detection Algorithms Based on ADMIN for Massive MIMO

This paper proposes the alternating direction method of multipliers-based infinity-norm(ADMIN) with threshold(ADMIN-T) and with percentage(ADMIN-P) detection algorithms,which make full use of the distribution of the signal to interference plus noise ratio(SINR) for an uplink massive MIMO system.The ADMIN-T and ADMIN-P detection algorithms are improved visions of the ADMIN detection algorithm,in which an appropriate SINR threshold in the ADMIN-T detection algorithm and a certain percentage in the ADMIN-P detection algorithm are designed to reduce the overall computational complexity.The detected symbols are divided into two parts by the SINR threshold which is based on the cumulative probability density function(CDF) of SINR and a percentage,respectively.The symbols in higher SINR part are detected by MMSE.The interference of these symbols is then cancelled by successive interference cancellation(SIC).Afterwards the remaining symbols with low SINR are iteratively detected by ADMIN.The simulation results show that the ADMIIN-T and the ADMIN-P detection algorithms provide a significant performance gain compared with some recently proposed detection algorithms.In addition,the computational complexity of ADMIN-T and ADMIN-P are significantly reduced.Furthermore,in the case of same number of transceiver antennas,the proposed algorithms have a higher performance compared with the case of asymmetric transceiver antennas.

Modelling and Performance Analysis of Visible Light Communication System in Industrial Implementations

Visible light communication(VLC)has a paramount role in industrial implementations,especially for better energy efficiency,high speed-data rates,and low susceptibility to interference.However,since studies on VLC for industrial implementations are in scarcity,areas concerning illumination optimisation and communication performances demand further investigation.As such,this paper presents a new modelling of light fixture distribution for a warehouse model to provide acceptable illumination and communication performances.The proposed model was evaluated based on various semi-angles at half power(SAAHP)and different height levels for several parameters,including received power,signal to noise ratio(SNR),and bit error rate(BER).The results revealed improvement in terms of received power and SNR with 30 Mbps data rate.Various modulations were studied to improve the link quality,whereby better average BER values of 5.55×10^(−15) and 1.06×10^(−10) had been achieved with 4 PAM and 8 PPM,respectively.The simulation outcomes are indeed viable for the practical warehouse model.

Flat Supercontinuum Generation at 1550 nm in a Dispersion-Flattened Microstructure Fibre Using Picosecond Pulse

The generation of a flat supercontinuum of over 80nm in the 1550nm region by injecting 1.6ps 10 GHz repetition rate optical pulses into an 80-m-long dispersion-flattened microstructure fibre is demonstrated. The fibre has small normal dispersion with a variation smaller than 1.5 （ps·nm^-1·km^-1） between 1500 and 1650nm. The generated supercontinuum ranging from 1513 to 1591 nm has the flatness of ±1.5 dB and it is not so flat in the range of several nanometres around the pump wavelength 1552nm. Numerical simulation is also used to study the effect of optical loss, fibre parameters and pumping conditions on supercontinuum generation in the dispersion-flattened microstructure fibre, and can be used for further optimization to generate flat broad spectra.

Stable single longitudinal mode erbium-doped silica fiber laser based on an asymmetric linear three-cavity structure

We present a stable linear-cavity single longitudinal mode （SLM） erbium-doped silica fiber laser. It consists of four fiber Bragg gratings （FBGs） directly written in a section of photosensitive erbium-doped fiber （EDF） to form an asymmetric three-cavity structure. The stable SLM operation at a wavelength of 1545.112 nm with a 3-dB bandwidth of 0.012 nm and an optical signal-to-noise ratio （OSNR） of about 60 dB is verified experimentally. Under laboratory conditions, the performance of a power fluctuation of less than 0.05 dB observed from the power meter for 6 h and a wavelength variation of less than 0.01 nm obtained from the optical spectrum analyzer （OSA） for about 1.5 h are demonstrated. The gain fiber length is no longer limited to only several centimeters for SLM operation because of the excellent mode-selecting ability of the asymmetric three-cavity structure. The proposed scheme provides a simple and cost-effective approach to realizing a stable SLM fiber laser.

A novel method of rapidly modeling optical properties of actual photonic crystal fibres

The flexible structure of photonic crystal fibre not only offers novel optical properties but also brings some difficulties in keeping the fibre structure in the fabrication process which inevitably cause the optical properties of the resulting fibre to deviate from the designed properties. Therefore, a method of evaluating the optical properties of the actual fibre is necessary for the purpose of application. Up to now, the methods employed to measure the properties of the actual photonic crystal fibre often require long fibre samples or complex expensive equipments. To our knowledge, there are few studies of modeling an actual photonic crystal fibre and evaluating its properties rapidly. In this paper, a novel method, based on the combination model of digital image processing and the finite element method, is proposed to rapidly model the optical properties of the actual photonic crystal fibre. Two kinds of photonic crystal fibres made by Crystal Fiber A/S are modeled. It is confirmed from numerical results that the proposed method is simple, rapid and accurate for evaluating the optical properties of the actual photonic crystal fibre without requiring complex equipment.

Design and analysis of a novel single-mode single-polarization photonic crystal fibre based on polarization-dependent coupling and absorption effect

A novel single-mode single-polarization （SMSP） photonic crystal fibre has been proposed and analysed based on the polarization-dependent coupling and absorption effect via a full-vector finite element method with perfectly matched layers. The numerical results predict that very efficient SMSP operation can be achieved with both high bandwidth and high extinction ratio at low loss penalty. Effects of the fibre structural parameters on the SMSP bandwidth and extinction ratio have been explored, which will provide useful guide for the design and fabrication of the fibre. The results obtained will be instructive for the realization of new SMSP fibres with high performance.

An Ultra-Broadband Single-Polarization Single-Mode Photonic Crystal Fibre

An ultra broadband single-polarization single-mode （SPSM） photonic crystal fibre （PCF） is proposed and analysed by using the plane-wave expansion method and the beam propagation method. Numerical results demonstrate that the SPSM wavelength region nearly at 580 nm in width from 1. 461μm to 2.041μm is obtained in this PCF. The start wavelength of the SPSM region is close to the hole pitch, and the width of the SPSM region increases with the increasing hole pitch. Effects of dopant concentration on SPSM properties are investigated. The confinement loss decreases and the width of SPSM region widens slightly with the increasing dopant concentration. These results offer a new possibility of fabricating active doped SPSM PCFs with high performance that is crucial for improving the performance of linearly polarized fibre lasers.

MZI-based wavelength interrogation system with tunable-FBG

We proposed a scheme of fiber Bragg grating （FBG） sensor interrogation system based on all fiber Mach-Zehnder Interferometer （MZI） edge filter and tunable-FBG. The equal power signals from FBG sensor and tunable FBG are coupled into port 1 and port 2 of MZI respectively. The experimental results show that the interrogation precision of the proposed system is 0.02 nm in a range of I nm. Furthermore, the precision can be improved by adjusting the two interference arms of the filter.

The number of least degrees of freedom required for a polarization controller to transform any state of polarization to any other output covering the entire Poincar sphere

Using two typical types of polarization controller, this paper analyses theoretically and experimentally the fact that it is necessary to adjust at least three instead of two waveplates in order to transform any state of polarization to any other output covering the entire Poincar6 sphere. The experimental results are exactly in accordance with the theory discussed in this paper. It has corrected the conventional and inaccurate point of view that two waveplates of a polarization controller are adequate to complete the transformation of state of polarization.

Design and fabrication of Panda-type erbium-doped polarization-maintaining fibres

To obtain the stable operation of erbium-doped fibre laser, the simple and ideal technology is adopted by use of the erbium doped polarization maintaining fibre （EDPMF）. The design criteria of the Panda-type EDPMF are presented, which take into account the cutoff wavelength, mode field diameter, modal birefringence and background loss. Four groups of optimum structural paramcter combinations are determined in terms of the design criteria. Two kinds of the Panda-type EDPMFs are selected to be fabricated. The fabrication process and the parameter control of the Panda-type EDPMFs are presented in detail. Their refractive index profiles, birefringence and absorption spectra are experimentally investigated. The absorption coefficient of the EDPMF, whose core is co-doped with Bi, Ga, A1 and Ge, is about 57.9dB/m at 1.53μm. Co-doping Bi, Ga and A1 can greatly increase the erbium concentration in the silica-based fibre. The high birefringence is obtained for the Panda-type EDPMF. The group birefringence of the EDPMF, whose outer cladding diameter is 125 μm, is about 4.8 × 10%^-4.

8×10 Gb/s transmission system over 2015 km with dispersion compensation by fiber Bragg Grating

The cascaded chirp fiber Bragg gratings(CFBGs) with ITU-T standard wavelengths and wavelength grid are applied to compensate the dispersion of 8×10 Gb/s WDM system.The ASE of the EDFA could be reduced,the OSNR of the transmitted signal can be increased and the fluctuation of the EDFA gain can be restrained in a certain scope by the CFBG employed in the system.Experiment of error-free 8×10 Gb/s 2 015 km transmission without FEC and electric regeneration is demonstrated in this paper.In this system,only EDFA is used as amplifier,and no other form of dispersion compensator is adopted except CFBG.The experimental result showed that after 2015 km transmission,the consistency of the dispersion compensating for each channel is perfect.

Self-organized GaN/AlN hexagonal quantum-dots:strain distribution and electronic structure

This paper presents a finite element method of calculating strain distributions in and around the self-organized GaN/AlN hexagonal quantum dots. The model is based on the continuum elastic theory, which is capable of treating a quantum dot with an arbitrary shape. A truncated hexagonal pyramid shaped quantum dot is adopted in this paper. The electronic energy levels of the GaN/AlN system are calculated by solving a three-dimension effective mass Shrodinger equation including a strain modified confinement potential and polarization effects. The calculations support the previous results published in the literature.

Design of Phosphor-Free Single-Chip White Light-Emitting Diodes Using InAlGaN Irregular Multiple Quantum Well Structures

A novel approach for the design of phosphor-free single-chip white light-emitting diodes （LEDs） is proposed by employing InAIGaN irregular multiple quantum well （IMQW） structures. The electronic and optical properties of the designed InA1GaN IMQWs are analyzed in detail by fully considering the effects of strain, well-coupling, valence band-mixing, and quasi-bound states using the effective-mass Hamiltonian deduced from k. p theory. For comparison, three different types of InAIGaN IMQW structures with ultra-wide band spontaneous emission spectra are analyzed, and the results show that phosphor-free single-chip white light LEDs with more than 20Ohm emission band can be obtained using properly designed InAIGaN IMQW structures.

The influences of thickness of spacing layer and the elastic anisotropy on the strain fields and band edges of InAs/GaAs conical shaped quantum dots

Based on the continuum elastic theory, this paper presents a finite element analysis to investigate the influences of elastic anisotropy and thickness of spacing layer on the strain field distribution and band edges （both conduction band and valence band） of the InAs/CaAs conical shaped quantum dots. To illustrate these effects, we give detailed comparisons with the circumstances of isolated and stacking quantum dot for both anisotropic and isotropic elastic characteristics. The results show that, in realistic materials design and theoretical predication performances of the optoelectronic devices, both the elastic anisotropy and thickness of the spacing layer of stacked quantum dot should be taken into consideration.

Towards 640 Gbit/s wavelength conversion based on nonlinear polarization rotation in a semiconductor optical amplifier

Taking into account ultra-fast carrier dynamics, this paper models 640 Gbit/s wavelength conversion scheme based on nonlinear polarization rotation （NPR） in a single semiconductor optical amplifier （SOA） and investigates the performance of this kind of wavelength conversion scheme in detail. In this model, two carrier temperature equations are introduced to substitute two energy density equations, which reduce the complexity of calculation in comparison with the previous model. The temporary gain and phase shift dynamics induced by ultra-short optical pulses are numerically simulated and the simulated results are qualitatively in good agreement with reported experimental results. Simulated results show that non-inverted and inverted 640 Gbit/s wavelength conversions based on NPR are achieved with clear open eye diagrams. To further investigate the performance of the non-inverted wavelength conversion scheme, the dependence of output extinction ratio （ER） on some key parameters used in simulation is illustrated. Furthermore, simulated analyses show that high performance non-inverted wavelength conversion based on NPR can be achieved by using a red-shifted filtering scheme.

Six-State Quantum Key Distribution Using Photons with Orbital Angular Momentum

A new implementation of high-dimensional quantum key distribution （QKD） protocol is discussed. Using three mutual unbiased bases, we present a d？level six-state QKD protocol that exploits the orbital angular momentum with the spatial mode of the light beam. The protocol shows that the feature of a high capacity since keys are encoded using photon modes in d-level Hilbert space. The devices for state preparation and measurement are also discussed. This protocol has high security and the alignment of shared reference frames is not needed between sender and receiver.

Research and Progress of Service Driven Optical Switching Network in China

National R&D activities on optical switching networkare introduced. Optical switching network testbedswere established in China including 3T-net andOBS ring and mesh network test-bed with the supportof national '863' program. As an importantmodule in OPS network, a novel all-optical serialmulticast mode is discussed.

Novel method to optimize the distributed pump powers in a kilowatt ytterbium-doped double-clad fiber laser

The rate equations with multipoint boundary conditions are solved by numerical method accurately.A novel method based on genetic algorithm is proposed to optimize distributed pump powers in kilowatt YDDC fiber laser in this paper.The calculated results show that lower operation temperature and better uniformity can be achieved through an optimized pump arrangement.

Supercontinuum Generationin Normal-dispersion Photonic Crystal Fiber Using Picosecond Pulse

Studied is the Super-continuum(SC) generation of a normal-dispersion photonic crystal fiber(PCF) using picosecond pulse excitation. In experimental analyses, a 237 nm broadband infrared continuum was generated pumped at 1 550 nm(normal dispersion regime) by 1.6 ps pulses from an erbium-doped fiber laser. In addition, we conduct the numerical analyses of SC based on generalized nonlinear Schr dionger equation. The results have been applied to investigate the dominant physical processes underlie the generation of SC. We conclude that dispersion, self-phase modulation(SPM),four-wave-mixing(FWM) and Raman scattering are determinants of SC generation rather than fission of soliton in normal-dispersion PCF.