期刊文献+
共找到2篇文章
< 1 >
每页显示 20 50 100
Characteristics and formation mechanisms of defect bands in vacuum-assisted high-pressure die casting AE44 alloy 被引量:3
1
作者 Ying-ying HOU Meng-wu WU +2 位作者 Bing-hui TIAN Xiao-bo LI Shou-mei XIONG 《Transactions of Nonferrous Metals Society of China》 SCIE EI CAS CSCD 2022年第6期1852-1865,共14页
The microstructure in vacuum-assisted high-pressure die casting(HPDC) Mg-4Al-4RE(AE44) alloy was studied. Special attention was paid to the characteristics of defect bands and their formation mechanisms. Since double ... The microstructure in vacuum-assisted high-pressure die casting(HPDC) Mg-4Al-4RE(AE44) alloy was studied. Special attention was paid to the characteristics of defect bands and their formation mechanisms. Since double defect bands are commonly observed, the cross section of die cast samples is divided into five parts with different grain morphologies and size distributions. The inner defect band is much wider than the outer one. Both the defect bands are solute segregation bands, resulting in a higher area fraction of Al;RE;phase than that in the adjacent regions. No obvious aggregation of porosities is observed in the defect bands of AE44 alloy. This may be due to a narrow solidification temperature range of AE44 alloy and a large amount of latent heat released during the precipitation of intermetallic phases. The formation of the defect bands is related to the shear stress acting upon the partially solidified alloy, which can lead to collapse of the grain network. However, the generation mechanisms of shear stress in the outer and inner defect bands are quite different. 展开更多
关键词 high-pressure die casting magnesium alloy AE44 microstructure defect band
下载PDF
压铸镁合金缺陷带的组织特征及形成机理 被引量:3
2
作者 吴孟武 侯莹滢 +3 位作者 李晓波 熊守美 陆文兴 王运桂 《特种铸造及有色合金》 CAS 北大核心 2020年第2期117-122,共6页
研究了压铸镁合金缺陷带的组织形貌及分布特征,建立缺陷带与压室预结晶(ESCs)、气缩孔及压铸工艺参数之间的对应关系,在此基础上探讨了缺陷带的形成及演化机理。结果表明,压铸镁合金截面凝固组织以缺陷带为界可划分为3个有明显组织特征... 研究了压铸镁合金缺陷带的组织形貌及分布特征,建立缺陷带与压室预结晶(ESCs)、气缩孔及压铸工艺参数之间的对应关系,在此基础上探讨了缺陷带的形成及演化机理。结果表明,压铸镁合金截面凝固组织以缺陷带为界可划分为3个有明显组织特征差异的区域。随着压铸低速速度提高,镁合金凝固组织中ESCs含量逐渐降低,而缺陷带组织愈加明显并向压铸件中心靠拢,缺陷带宽度减小,其内部孔洞更加聚集;高速速度越大,压铸镁合金凝固组织中ESCs越分散,缺陷带向压铸件中心靠拢,压铸在无高速速度情况下,镁合金凝固组织横截面出现双缺陷带现象。压铸充型过程中金属液流的形态决定了缺陷带的分布位置和发展趋势,在高速金属液的剧烈冲刷及增压压力的作用下,靠近金属液流外轮廓的晶粒发生破碎或转动,在晶粒间形成大于剩余金属液体积的间隙,随着凝固的进行,形成沿液流轮廓分布孔洞聚集的缺陷带组织。 展开更多
关键词 镁合金 冷室压铸 缺陷带 微观组织
原文传递
上一页 1 下一页 到第
使用帮助 返回顶部