螺旋波等离子体源以其高电离效率与高密度优势受到多个领域的青睐。螺旋波放电高电离效率的机理或者功率耦合模式,一直是困扰该领域学者的难点之一,对于放电过程与特性的诊断则是揭示其物理机制的重要途径。光谱诊断能够克服介入式诊断...螺旋波等离子体源以其高电离效率与高密度优势受到多个领域的青睐。螺旋波放电高电离效率的机理或者功率耦合模式,一直是困扰该领域学者的难点之一,对于放电过程与特性的诊断则是揭示其物理机制的重要途径。光谱诊断能够克服介入式诊断手段对等离子体的干扰同时受等离子体烧蚀等弊端,且响应速度快、操作灵活。为研究螺旋波等离子体的放电特性以及气体压力的影响,开展了以氩气为工质气体的光谱实验研究,并针对实验开展了Helic程序数值模拟。通过改变光纤探头焦距调整径向诊断位置,得到谱线强度的径向分布。由氩原子4p-4s能级跃迁产生的谱线主要集中在740~920 nm区间,谱线相对强度较离子激发谱线较强。实验研究发现,在较低氩气压力范围(0.2 Pa< P Ar <1.0 Pa),随着压力增加,放电光强迅速增加,但是当压力增加到大于1.0 Pa之后,光强增长的趋势变缓,甚至部分谱线的相对强度不再增长,达到类饱和状态,朗缪尔探针测量得到离子密度变化趋势与其相似。光强分布在靠近径向边界处( r ≈4 cm)存在凸起,且随压力增加,该凸起分布更为明显。通过对电子温度的计算发现,压力增加到一定程度将影响放电均匀性。仿真结果显示,增大压力,功率沉积密度的径向分布逐渐向径向边界处积累,与实验观察到的谱线强度径向凸起相一致,螺旋波与TG波的耦合效率增加。随着气体压力的增加,Er的径向边界峰值降低,原因是波所受阻尼增强, TG波被有效地局限于径向较窄的边界处。电流密度轴向分量Jz在等离子体内部和边界处的峰值呈显著的减小趋势,可见,虽然压力增加一定程度上提高了等离子体密度,但却相应的减小了电离率,导致轴向电流密度受限。但是径向电流密度Jr却呈现先减小后增大的趋势,且增长幅度明显,综合来看,放电效率有所提高。可见适当增加气体压力,有助于提高放电的功率耦合效率和强度,增加等离子体密度。光强比值法是针对线性谱线参数计算的典型方法, Helic程序亦是专业领域内认可度很高的计算工具,结果可靠,分析方法具有可借鉴性。实验及仿真结果对于提高氩气工质下的螺旋波放电强度提供了一定的参考价值。展开更多
Development of magnetohydrodynamic acceleration technology is expected to improve wind tunnel simulation capability and testing capability.The underlying premise is to produce uniform and stable plasma in supersonic a...Development of magnetohydrodynamic acceleration technology is expected to improve wind tunnel simulation capability and testing capability.The underlying premise is to produce uniform and stable plasma in supersonic air flow,and gas discharge is an effective way to achieve this.A nanosecond pulsed discharge experimental system under supersonic conditions was established,and a pin-to-plate nanosecond pulsed discharge experiment in Mach 2 air flow was performed to verify that the proposed method produced uniform and stable plasma under supersonic conditions.The results show that the discharge under supersonic conditions was stable overall,but uniformity was not as good as that under static conditions.Increasing the number of pins improved discharge uniformity,but reduced discharge intensity and hence plasma density.Under multi-pin conditions at 1000Hz,the discharge was almost completely corona discharge,with the main current component being the displacement current,which was smaller than that under static conditions.展开更多
文摘螺旋波等离子体源以其高电离效率与高密度优势受到多个领域的青睐。螺旋波放电高电离效率的机理或者功率耦合模式,一直是困扰该领域学者的难点之一,对于放电过程与特性的诊断则是揭示其物理机制的重要途径。光谱诊断能够克服介入式诊断手段对等离子体的干扰同时受等离子体烧蚀等弊端,且响应速度快、操作灵活。为研究螺旋波等离子体的放电特性以及气体压力的影响,开展了以氩气为工质气体的光谱实验研究,并针对实验开展了Helic程序数值模拟。通过改变光纤探头焦距调整径向诊断位置,得到谱线强度的径向分布。由氩原子4p-4s能级跃迁产生的谱线主要集中在740~920 nm区间,谱线相对强度较离子激发谱线较强。实验研究发现,在较低氩气压力范围(0.2 Pa< P Ar <1.0 Pa),随着压力增加,放电光强迅速增加,但是当压力增加到大于1.0 Pa之后,光强增长的趋势变缓,甚至部分谱线的相对强度不再增长,达到类饱和状态,朗缪尔探针测量得到离子密度变化趋势与其相似。光强分布在靠近径向边界处( r ≈4 cm)存在凸起,且随压力增加,该凸起分布更为明显。通过对电子温度的计算发现,压力增加到一定程度将影响放电均匀性。仿真结果显示,增大压力,功率沉积密度的径向分布逐渐向径向边界处积累,与实验观察到的谱线强度径向凸起相一致,螺旋波与TG波的耦合效率增加。随着气体压力的增加,Er的径向边界峰值降低,原因是波所受阻尼增强, TG波被有效地局限于径向较窄的边界处。电流密度轴向分量Jz在等离子体内部和边界处的峰值呈显著的减小趋势,可见,虽然压力增加一定程度上提高了等离子体密度,但却相应的减小了电离率,导致轴向电流密度受限。但是径向电流密度Jr却呈现先减小后增大的趋势,且增长幅度明显,综合来看,放电效率有所提高。可见适当增加气体压力,有助于提高放电的功率耦合效率和强度,增加等离子体密度。光强比值法是针对线性谱线参数计算的典型方法, Helic程序亦是专业领域内认可度很高的计算工具,结果可靠,分析方法具有可借鉴性。实验及仿真结果对于提高氩气工质下的螺旋波放电强度提供了一定的参考价值。
基金National Natural Science Foundation of China (Nos. 11372352, 51776222)the China Postdoctoral Science Foundation (Nos. 2017T100772, 2016M590972).
文摘Development of magnetohydrodynamic acceleration technology is expected to improve wind tunnel simulation capability and testing capability.The underlying premise is to produce uniform and stable plasma in supersonic air flow,and gas discharge is an effective way to achieve this.A nanosecond pulsed discharge experimental system under supersonic conditions was established,and a pin-to-plate nanosecond pulsed discharge experiment in Mach 2 air flow was performed to verify that the proposed method produced uniform and stable plasma under supersonic conditions.The results show that the discharge under supersonic conditions was stable overall,but uniformity was not as good as that under static conditions.Increasing the number of pins improved discharge uniformity,but reduced discharge intensity and hence plasma density.Under multi-pin conditions at 1000Hz,the discharge was almost completely corona discharge,with the main current component being the displacement current,which was smaller than that under static conditions.
