Switching expansion reduction(SER)uses a switch valve instead of the throttle valve to realize electronically controlled pressure reduction for high pressure pneumatics.A comprehensive and interactive pneumatic simula...Switching expansion reduction(SER)uses a switch valve instead of the throttle valve to realize electronically controlled pressure reduction for high pressure pneumatics.A comprehensive and interactive pneumatic simulation model according to the experimental setup of SER has been built.The mathematical model considers heat exchanges,source air pressure and temperature,environmental temperatures and heat transfer coefficients variations.In addition,the compensation for real gas effect is used in the model building.The comparison between experiments and simulations of SER indicates that,to compensate the real gas effect in high pressure discharging process,the thermal capacity of air supply container in simulation should be less than the actual value.The higher the pressure range,the greater the deviation.Simulated and experimental results are highly consistent within pressure reduction ratios ranging from 1.4 to 20 and output air mass flow rates ranging from 3.5 to 132 g/s,which verifies the high adaptability of SER and the validity of the mathematic model and the compensation method.展开更多
The energy balance, air internal energy, enthalpy and exergy transfers of high pressure switching expansion reduction （SER） are comparatively analyzed in this paper to give a better understanding about the exergy an...The energy balance, air internal energy, enthalpy and exergy transfers of high pressure switching expansion reduction （SER） are comparatively analyzed in this paper to give a better understanding about the exergy analysis and its difference between energy conversion analyses for the pneumatics. In SER, the exergy transfer efficiency is much lower than the enthalpy efficiency. The enthalpy efficiency is primarily related to the initial pressure of supply tanks, and the exergy efficiency is primarily related to the pressure reduction ratios. Heat transfers increase the internal energy, enthalpy and exergy of air; the influence on exergy is relatively small. The total enthalpy in SER decreases as the air temperature decreases in the expansion process of the air. And exergy loss is primarily related to the irreversible process of isenthalpic throttling but not energy conversion. Based on the analyses, to improve the exergy efficiency of the pneumatics, the pressure reduction without power output should be avoided.展开更多
A single on/off valve is used to carry out the position control of the asymmetrical hydraulic cylinder. The influence of the nominal flow rate on the positional accuracy of piston is investigated and the proximate for...A single on/off valve is used to carry out the position control of the asymmetrical hydraulic cylinder. The influence of the nominal flow rate on the positional accuracy of piston is investigated and the proximate formula for calculating the nominal flow rate of on/off valve is introduced. The system structure proposed in this paper could avoid cavitation and hyper pressure in two chambers to some extent. The simulation results indicated that the control method in this paper could satisfy the expected control requirements.展开更多
基金Project(51205421)supported by the National Natural Science Foundation of ChinaProject(2012M521647)supported by the Postdoctoral Science Foundation of China
文摘Switching expansion reduction(SER)uses a switch valve instead of the throttle valve to realize electronically controlled pressure reduction for high pressure pneumatics.A comprehensive and interactive pneumatic simulation model according to the experimental setup of SER has been built.The mathematical model considers heat exchanges,source air pressure and temperature,environmental temperatures and heat transfer coefficients variations.In addition,the compensation for real gas effect is used in the model building.The comparison between experiments and simulations of SER indicates that,to compensate the real gas effect in high pressure discharging process,the thermal capacity of air supply container in simulation should be less than the actual value.The higher the pressure range,the greater the deviation.Simulated and experimental results are highly consistent within pressure reduction ratios ranging from 1.4 to 20 and output air mass flow rates ranging from 3.5 to 132 g/s,which verifies the high adaptability of SER and the validity of the mathematic model and the compensation method.
基金the National Natural Science Foundation of China(No.51205421)the Fund of the Key Laboratory of Sensing Technology and Biomedical Instruments of Guangdong Province(No.2011A060901013)
基金the National Natural Science Foundation of China(No.50575202)
文摘The energy balance, air internal energy, enthalpy and exergy transfers of high pressure switching expansion reduction （SER） are comparatively analyzed in this paper to give a better understanding about the exergy analysis and its difference between energy conversion analyses for the pneumatics. In SER, the exergy transfer efficiency is much lower than the enthalpy efficiency. The enthalpy efficiency is primarily related to the initial pressure of supply tanks, and the exergy efficiency is primarily related to the pressure reduction ratios. Heat transfers increase the internal energy, enthalpy and exergy of air; the influence on exergy is relatively small. The total enthalpy in SER decreases as the air temperature decreases in the expansion process of the air. And exergy loss is primarily related to the irreversible process of isenthalpic throttling but not energy conversion. Based on the analyses, to improve the exergy efficiency of the pneumatics, the pressure reduction without power output should be avoided.
基金the National Natural Science Foundation of China (No. 50575202)
文摘A single on/off valve is used to carry out the position control of the asymmetrical hydraulic cylinder. The influence of the nominal flow rate on the positional accuracy of piston is investigated and the proximate formula for calculating the nominal flow rate of on/off valve is introduced. The system structure proposed in this paper could avoid cavitation and hyper pressure in two chambers to some extent. The simulation results indicated that the control method in this paper could satisfy the expected control requirements.
