期刊文献+
共找到3篇文章
< 1 >
每页显示 20 50 100
钙处理过程中ML08Al钢非金属夹杂物变化热力学分析
1
作者 荆高扬 《金属制品》 2018年第1期59-61,共3页
ML08Al钢在浇注过程中水口易出现堵塞,降低生产效率。钢中存在大量的Al_2O_3及其他高熔点铝酸钙附着在水口表面并不断聚集是引起水口堵塞的主要原因。采用钙处理工艺可明显降低水口堵塞发生率,但水口堵塞现象仍时有发生。为寻找合适的... ML08Al钢在浇注过程中水口易出现堵塞,降低生产效率。钢中存在大量的Al_2O_3及其他高熔点铝酸钙附着在水口表面并不断聚集是引起水口堵塞的主要原因。采用钙处理工艺可明显降低水口堵塞发生率,但水口堵塞现象仍时有发生。为寻找合适的钙处理工艺条件,通过热力学计算得出1 600℃时钢水中Al-O、Al-Ca、Al-S平衡曲线,分析在钙处理过程中生成12CaO·7Al_2O_3时各主要元素质量分数控制区间,并将实际控制情况与理论计算结果进行对比,从理论上评价钙处理的控制水平。 展开更多
关键词 ML08A1 冷镦钢 钙处理 非金属夹杂物
下载PDF
SWRH82A+Cr热轧盘条生产工艺实践 被引量:1
2
作者 李涛 姜洪刚 +1 位作者 吕建勋 荆高扬 《金属制品》 2015年第2期41-43,51,共4页
介绍SWRH82A+Cr热轧盘条的化学成分设计和生产工艺路线。生产工艺控制过程中,转炉终点控制w(C)≥0.50%,出钢时间控制在5-7 min;LF炉精炼过程中控制软吹氩时间不小于15 min,精炼总周期控制在75min左右;连铸过程中控制钢水过热度在30... 介绍SWRH82A+Cr热轧盘条的化学成分设计和生产工艺路线。生产工艺控制过程中,转炉终点控制w(C)≥0.50%,出钢时间控制在5-7 min;LF炉精炼过程中控制软吹氩时间不小于15 min,精炼总周期控制在75min左右;连铸过程中控制钢水过热度在30℃以下;轧制过程中控制开轧温度(1 020±20)℃,吐丝温度(890±20)℃,风冷辊道速度0.8 m/s,冷却速率16℃/s。盘条显微组织为S+P+少量渗碳体,晶粒度为8.0级,索氏体体积分数在85%以上,抗拉强度控制在1 196-1 221 MPa,断面收缩率和断后伸长率分别控制在39%-42%和13.5%-16.5%,产品质量满足客户要求。 展开更多
关键词 SWRH82A 力学性能 非金属夹杂物 晶粒度 网状渗碳体
下载PDF
Coarsening Behavior ofγ′Precipitates and Compression Performance of Novel Co-Ni-Al-W Superalloy
3
作者 Zhou Cheng Jin Lei +2 位作者 Jing Gaoyang Yu Boyan Zhao Jun 《稀有金属材料与工程》 SCIE EI CAS CSCD 北大核心 2024年第10期2786-2793,共8页
The coarsening behavior ofγʹprecipitate phase at different temperatures and the compressive performance of novel Co-Ni-Al-W superalloy were investigated.Experiment results show that the evolution of the mean radius a... The coarsening behavior ofγʹprecipitate phase at different temperatures and the compressive performance of novel Co-Ni-Al-W superalloy were investigated.Experiment results show that the evolution of the mean radius and volume fraction of theγʹphase obeys the classical Lifshitz-Slyozov-Wagner model.The coarsening rate of theγʹphase exhibits a significant dependence on the aging temperature,which increases from 1.30×10^(−27)m^(3)/s at 800℃to 9.56×10−27 m^(3)/s at 900℃.The activation energy ofγʹphase is mainly influenced by the W diffusion in theγmatrix,presenting as 210 kJ/mol.The prepared Co-Ni-Al-W alloy possesses superb comprehensive properties,particularly the good combination of highγʹsolvus temperature(1221℃)and low density(8.7 g/cm^(3)).Besides,the compressive yield strength of the Co-Ni-Al-W alloy at ambient and high temperatures are higher than that of otherγʹ-strengthened Co-based superalloys.The compressive yield strength of the Co-Ni-Al-W alloy at 850℃is as high as 774 MPa. 展开更多
关键词 Co-Ni-Al-W superalloy γʹphase coarsening behavior compressive performance
原文传递
上一页 1 下一页 到第
使用帮助 返回顶部