In order to analyze the spray characteristics of non-circular nozzle holes based on the air-assisted spray system, the spray characteristics of circular and non-circular nozzles were studied under the pressure of 0.2-...In order to analyze the spray characteristics of non-circular nozzle holes based on the air-assisted spray system, the spray characteristics of circular and non-circular nozzles were studied under the pressure of 0.2-0.6 MPa and the spray volume of 1000-5000 mL/h. Elliptical nozzle and triangular nozzle are classified as non-circular geometries. The spray cone angle was measured by processing the spray image captured by a CCD camera. The measured spray cone angles of the circular nozzles were analyzed, and the axis switching phenomenon of minor plane of elliptical nozzle was found during the test. Among the three shapes of nozzles, the elliptical nozzle had the largest spray cone angle, and the triangular nozzle had the smallest. The velocity field obtained depended on the PIV system. The results show that for axial velocity, elliptical orifice spray has greater kinetic energy and smaller droplet size under the same working parameters. Compared with the circular and elliptical nozzles, triangular orifice reached maximum spray velocity the fastest, but its velocity decay was the fastest. For radial velocity, away from the axis, the spray velocity of the elliptical orifice was less affected by the injection parameters, and the velocity was less than that of circular orifice and triangle orifice. Increasing air pressure will weaken radial propagation. The increase of liquid spraying rate had no remarkable effect on the increase of spraying rate. The results of particle size analysis show that the particle size of the non-circular orifice is reduced compared with that of the circular orifice, which promotes the breakup of droplets to a certain extent and enhances the atomization effect.展开更多
Discrete element modelling(DEM)is a numerical method for examining the dynamic behavior of granular media.In order to build an accurate simulation model and provide more comprehensive soil characteristic parameters fo...Discrete element modelling(DEM)is a numerical method for examining the dynamic behavior of granular media.In order to build an accurate simulation model and provide more comprehensive soil characteristic parameters for the design and optimization of various soil contact machinery,in this paper,the discrete element simulation method(EDEM)combined with experimental approach is used to investigate the soil contact characteristic parameters in East Asia.In this study,Hertze-Mindlin(no slip)was used as a particle contact model by taking particle contact parameters and soil JKR(Johnson-Kendall-Roberts)surface energy as determinants,and repose angle,internal friction angle,and cohesive force as evaluation indexes.The method of Plackett-Burman,Stepest ascent,and Box-Behnken were used to gradually reduce the range of parameters needed for simulation until the most accurate value was determined.The results show that the restitution coefficient,static friction coefficient,and rolling friction coefficient between soil particles have significant effects on the DEM model,and their value of them are 0.596,0.725,and 0.16,respectively.Based on these parameters used for the repose angle test and direct shear stress test,the value of repose angle is 31.97°,the internal friction angle is 27.61°,and the cohesive force is 33.06 kPa.The relative errors with the actual measured values are 9.54%,1.87%,and 2.31%,respectively.In order to further test whether the simulation parameters of soil obtained by repose angle test and direct shear stress test are consistent with the real soil,comparison test between field test and discrete element simulation was used.The results show that the error in height of ridge between the simulated soil and the actual soil is 4.06%,which is within the acceptable range.It also indicates that the calibrated and optimized soil simulation model can accurately represent the real soil.The research provides theoretical basis and technical support for the study of soil contact parts by using the discrete element method,combined with repose angle test and direct shear stress test.展开更多
基金Sponsored by the National Key R&D Project(Grant No.2019YFD1002500)the Key Projects of Science and Technology Support Plan of JiangsuP rovince(Grant No.BE2016341)the Open Fund of State Key Laboratory of Internal Combustion Engine(Grant No.GKF2015-004)。
文摘In order to analyze the spray characteristics of non-circular nozzle holes based on the air-assisted spray system, the spray characteristics of circular and non-circular nozzles were studied under the pressure of 0.2-0.6 MPa and the spray volume of 1000-5000 mL/h. Elliptical nozzle and triangular nozzle are classified as non-circular geometries. The spray cone angle was measured by processing the spray image captured by a CCD camera. The measured spray cone angles of the circular nozzles were analyzed, and the axis switching phenomenon of minor plane of elliptical nozzle was found during the test. Among the three shapes of nozzles, the elliptical nozzle had the largest spray cone angle, and the triangular nozzle had the smallest. The velocity field obtained depended on the PIV system. The results show that for axial velocity, elliptical orifice spray has greater kinetic energy and smaller droplet size under the same working parameters. Compared with the circular and elliptical nozzles, triangular orifice reached maximum spray velocity the fastest, but its velocity decay was the fastest. For radial velocity, away from the axis, the spray velocity of the elliptical orifice was less affected by the injection parameters, and the velocity was less than that of circular orifice and triangle orifice. Increasing air pressure will weaken radial propagation. The increase of liquid spraying rate had no remarkable effect on the increase of spraying rate. The results of particle size analysis show that the particle size of the non-circular orifice is reduced compared with that of the circular orifice, which promotes the breakup of droplets to a certain extent and enhances the atomization effect.
基金This work was financially supported by the National Science and Technology Major Project of China(Grant No.2019YFD 1002502)the National Natural Science Foundation of China(Grant No.51675239)+2 种基金The Natural Science Fund Project of Colleges in Jiangsu Province of China(Grant No.19KJA430018)The Important Development Program of Ningxia Province of China(Grant No.2018BBF02020)The Research and Development Program of Zhenjiang Province of China(Grant No.NY2019015).
文摘Discrete element modelling(DEM)is a numerical method for examining the dynamic behavior of granular media.In order to build an accurate simulation model and provide more comprehensive soil characteristic parameters for the design and optimization of various soil contact machinery,in this paper,the discrete element simulation method(EDEM)combined with experimental approach is used to investigate the soil contact characteristic parameters in East Asia.In this study,Hertze-Mindlin(no slip)was used as a particle contact model by taking particle contact parameters and soil JKR(Johnson-Kendall-Roberts)surface energy as determinants,and repose angle,internal friction angle,and cohesive force as evaluation indexes.The method of Plackett-Burman,Stepest ascent,and Box-Behnken were used to gradually reduce the range of parameters needed for simulation until the most accurate value was determined.The results show that the restitution coefficient,static friction coefficient,and rolling friction coefficient between soil particles have significant effects on the DEM model,and their value of them are 0.596,0.725,and 0.16,respectively.Based on these parameters used for the repose angle test and direct shear stress test,the value of repose angle is 31.97°,the internal friction angle is 27.61°,and the cohesive force is 33.06 kPa.The relative errors with the actual measured values are 9.54%,1.87%,and 2.31%,respectively.In order to further test whether the simulation parameters of soil obtained by repose angle test and direct shear stress test are consistent with the real soil,comparison test between field test and discrete element simulation was used.The results show that the error in height of ridge between the simulated soil and the actual soil is 4.06%,which is within the acceptable range.It also indicates that the calibrated and optimized soil simulation model can accurately represent the real soil.The research provides theoretical basis and technical support for the study of soil contact parts by using the discrete element method,combined with repose angle test and direct shear stress test.