Assessing the Impact of Fugitive Dust Emissions from Cement Silos at Cluster of Concrete Batching Facilities Using Air Dispersion Modeling

This research assessed the environmental impact of cement silos emission on the existing concrete batching facilities in M35-Mussafah, Abu Dhabi, United Arab Emirates. These assessments were conducted using an air quality dispersion model (AERMOD) to predict the ambient concentration of Portland Cement particulate matter less than 10 microns (PM10) emitted to the atmosphere during loading and unloading activities from 176 silos located in 25 concrete batching facilities. AERMOD was applied to simulate and describe the dispersion of PM10 released from the cement silos into the air. Simulations were carried out for PM10 emissions on controlled and uncontrolled cement silos scenarios. Results showed an incremental negative impact on air quality and public health from uncontrolled silos emissions and estimated that the uncontrolled PM10 emission sources contribute to air pollution by 528958.32 kg/Year. The modeling comparison between the controlled and uncontrolled silos shows that the highest annual average concentration from controlled cement silos is 0.065 μg/m3, and the highest daily emission value is 0.6 μg/m3;both values are negligible and will not lead to significant air quality impact in the entire study domain. However, the uncontrolled cement silos’ highest annual average concentration value is 328.08 μg/m3. The highest daily emission average value was 1250.09 μg/m3;this might cause a significant air pollution quality impact and health effects on the public and workers. The short-term and long-term average PM10 pollutant concentrations at these receptors predicted by the air dispersion model are discussed for both scenarios and compared with local and international air quality standards and guidelines.

Comparative Analysis of PM10 Emission Rates from Controlled and Uncontrolled Cement Silos in Concrete Batching Facilities

This research study quantifies the PM10 emission rates (g/s) from cement silos in 25 concrete batching facilities for both controlled and uncontrolled scenarios by applying the USEPA AP-42 guidelines step-by-step approach. The study focuses on evaluating the potential environmental impact of cement dust fugitive emissions from 176 cement silos located in 25 concrete batching facilities in the M35 Mussafah industrial area of Abu Dhabi, UAE. Emission factors are crucial for quantifying the PM10 emission rates (g/s) that support developing source-specific emission estimates for areawide inventories to identify major sources of pollution that provide screening sources for compliance monitoring and air dispersion modeling. This requires data to be collected involves information on production, raw material usage, energy consumption, and process-related details, this was obtained using various methods, including field visits, surveys, and interviews with facility representatives to calculate emission rates accurately. Statistical analysis was conducted on cement consumption and emission rates for controlled and uncontrolled sources of the targeted facilities. The data shows that the average cement consumption among the facilities is approximately 88,160 (MT/yr), with a wide range of variation depending on the facility size and production rate. The emission rates from controlled sources have an average of 4.752E-04 (g/s), while the rates from uncontrolled sources average 0.6716 (g/s). The analysis shows a significant statistical relationship (p < 0.05) and perfect positive correlation (r = 1) between cement consumption and emission rates, indicating that as cement consumption increases, emission rates tend to increase as well. Furthermore, comparing the emission rates from controlled and uncontrolled scenarios. The data showed a significant difference between the two scenarios, highlighting the effectiveness of control measures in reducing PM10 emissions. The study’s findings provide insights into the impact of cement silo emissions on air quality and the importance of implementing control measures in concrete batching facilities. The comparative analysis contributes to understanding emission sources and supports the development of pollution control strategies in the Ready-Mix industry.

Air Quality Indices, Sources and Impact on Human Health of PM₁₀and PM_2.5in Alexandria Governorate, Egypt

In this study, PM10 and PM2.5 were measured in seven sites representing different activities (the same sites of EEAA monitoring stations) in addition to eighth site that used as a background. All results were higher than AQLs of EEAA, US/EPA, and EC although PM10 and PM2.5 are considered to be a direct cause of cardiovascular diseases as well as lead to death and it may be a reason for a number of chest diseases in short-term as well as long-term. Results were compared to the Air Quality Forecast system which developed by EEAA and AQI which created by US/EPA was calculated for some PM10 and PM2.5. Probable potential anthropogenic sources for such high concentrations of PM included unpaved roads, indiscriminate demolition and construction work, industrial activities, and solid wastes. This study resulted in a number of suggestions and recommendations include: 1) Implementation of integrated ISO 26000 and ISO 14001, 2) EIMP/EEAA monitoring stations need restructuring plan to cover all areas in Alexandria, 3) EIMP/EEAA must be supported with PM2.5 monitors, 4) PM control systems must be used in all industrial activities to reduce PM pollution from the source, 5) AQL of PM2.5 in the ambient environment must be reduced and it must be included in the working environment parameters, 6) Environmental law must be applied strictly, and 7) Multidisciplinary co-operation especially between environment and public health specialists must be increased.

Decrease of TSP, PM₁₀, and Lead Concentration in a Lead Company in Alexandria City, Egypt

The study was carried out in a lead company inside Alexandria which exists in a residential area. Different sites have been selected inside the Department of Lead Improvement to measure TSP, PM10, and heavy lead during the melting process which takes place inside big alloying kettles and from the stack emissions. After that, the company made evaluation of the old factory and decision makers decided to make development for this factory through buying a complete unit for treatment with a special filter to make abatement for the level of emission especially for lead. The aim of this work is: 1) Put a plan for monitoring the level of different pollution after modification and to calculate the percentage of decrease (efficiency) of the new control unit through concentration of TSP, PM10, and lead through different processes;2) Install a new filter to abate the different air pollutants such as TSP, PM10, and lead. Total Suspended Particulate (TSP) and Respiratory dust (PM10) measured by using Volume sampler and Air mitrix. Lead was measured by the digestion of the samples with a mixture of hydrochloric and nitric acids and using Atomic Absorption Spectropho- tometer. Results of measuring TSP, PM10, Lead in working environment, and lead inside stack before and after installation of the new filter showed percentage of decrease from 22% to 120%, 33% to 160%, 26% to 102%, and 51% to 56.5% respectively.